Sanyo VCB-9324 User's Manual
Contents
1. E Multiple cameras connection You can use multiple cameras by connecting them a camera switcher or a quad unit sold separately then conducting the surveillance from one location by splitting the monitor screen to view the image from each camera or by switching the image from each camera on the monitor screen For detailed information please refer to the installed devices instruction manuals 2 Example of connection to a monitor B gt VIDEO IN ss VIDEO OUT CAUTION e Make sure the AC adaptor is not connected to the wall outlet before connecting it to the 24 V AC input terminals e When making the connections be careful to respect the polarity and not to shortcut the terminals 8 English SETTINGS AND ADJUSTMENTS E Adjusting the focus 1 Loosen the lens cover fixing screw A 2 Tum the cover counterclockwise to align the tab C on the lens cover with the tab B on the base and remove the cover 3 Remove the hood lens D then while watching the image on the monitor tum the focus ring E to adjust the focus 4 When finished install the hood lens then align the tab C on the lens cover with the tab B on the base and tum the cover dockwise until the tab F on the cover is aligned with the tab B on the base Tighten the lens cover fixing screw A English 9 TROUBLESHOOTING Before taking the camera for repairs please check below to mak2. the periods specified below SFC will repair or replace at its option the product and any of its parts which fail to conform to this warranty The warranty period commences on the date the product was first purchased or rented at retail LABOR PARTS IMAGE DEVICE 3 YEARS 3 YEARS 5 YEARS EXCLUSIONS This warranty does not cover A the adjustment of customer operated controls as explained in the appropriate model s instruction manual or B the repair of any product whose serial number has been altered defaced or removed This warranty shall not apply to the cabinet or cosmetic parts antenna knobs batteries or image burns to projection or picture tubes caused by electronic devices or games This warranty does not apply to uncrating setup installation removal of the product for repair or reinstallation of the product after repair This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including but not limited to any malfunction defect or failure caused by or resulting from unauthorized service or parts improper maintenance operation contrary to furnished instructions shipping or transit accidents modification or repair by the user abuse misuse neglect accident incorrect power line voltage fire flood or other Acts of God or normal wear and tear The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party
3. 0 sec Iris system Electronic iris Gain control Automatic Lens Built in F2 0 f 3 8 mm fixed focal lens focus adjustment Angle of view Horizontally Approx 71 Vertically Approx 53 Diagonal Approx 90 Operational environmental conditions Temperature 10 C 50 C Humidity less than 90 RH 24 V AC 2 1W Approx 160 g Features and specifications are subject to change without prior notice or obligations E DIMENSIONS 51 mm 10 English
4. PHASE volume on camera 2 try setting the LINE PHASE volume on camera 1 If it still cannot be corrected please check that the polarity of the power cords of all connected devices is correct CONNECTIONS AND INSTALLATION E Connecting the coaxial cable horizontally 1 Qut and prepare the extremity of the coaxial cable sold separately as illustrated 2 Attach the coaxial cable to the base Loosen the VIDEO OUT terminal screw A and the GND terminal screw B then insert the center wire of the coaxial cable in the VIDEO OUT terminal and make sure the shielding mesh part of the cable is located into the GND cable clamper then tighten both screws A and B to attach the cable a Connecting the coaxial cable vertically using the vertical holder Return the shielding mesh here plate Cut and prepare the extremity of the coaxial cable sold separately as illustrated Loosen the VIDEO OUT terminal screw and remove the GND terminal screw Insert the coaxial cable into the GND terminal damp a then attach the damp to the supplied vertical holder plate b using the screw c from the second GND terminal Attach the vertical holder plate to the GND terminal using the terminal screw then insert the centre wire of the coaxial cable into the VIDEO OUT terminal and tighten the terminal scew 6 English CONNECTIONS AND INSTALLATION E Installing the BNC plug sold separately To connect the camera to peripheral devices use a
5. SANYO INSTRUCTION MANUAL VCB 9324 B W CCD Camera About this manual Before installing and using the camera please read this manual carefully Be sure to keep it handy for later reference SANYO INDUSTRIAL VIDEO B W VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user s expense unless specifically stated otherwise in this warranty The names and addresses of Authorized Sanyo Service Centers may be obtained by writing to SFS Corporation SFC s warranty administrator at any of the addresses listed below or by calling toll free 1 800 421 5013 New Jersey Office California Office Illinois Office 210 Riser Road 1200 W Artesia Blvd 900 N Arlington Heights Rd Little Ferry NJ 07643 Compton CA 90220 Itasca IL 60143 201 641 3000 310 537 5830 708 775 1414 THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA EXCLUDING HAWAII AND ALL U S TERRITORIES AND PROTECTORATES THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL USER THE ORIGINAL DATED BILL OF SALE SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED Subject to the OBLIGATIONS above and EXCLUSIONS below SANYO FISHER USA CORPORATION warrants this SANYO product against defects in materials and workmanship for
6. This equipment IMPORTANT OPERATING AND MAINTENANCE generates uses and can radiate radio frequency energy and if INSTRUCTIONS IN THE LITERATURE ACCOMPANYING not installed and used in accordance with the instructions may THIS UNIT cause harmful interference to radio communications However there is no guarantee that interference will not occur in WARNING a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures TO PREVENT THE RISK OF ARE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver For the customers in Canada Connect the equipment into an outlet on a circuit different This Class B digital apparatus complies with Canadian ICES 003 from that to which the receiver is connected s x s Consult the dealer or an experienced radio TV technician for help Pour la dientele canadienne k a This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Cet appareil numerique de
7. coaxial cable with BNC plug 1 Cut the extremity of the coaxial cable sold separately as illustrated e Cable type RG 6U 5C 2V 500 m maximum If the type of peripheral devices connected the type of cable used and or the cable length are not as specified the image and synchronization signals may not be transmitted correctly CAUTION Use CCTV Video grade coaxial cable Due to its construction an RG 59U cable will not transmit the signal properly when installed through conduits or through the air and therefore cannot be used Insert the cable through the adaptor then tum the shielding mesh over Loosen the center wire securing screw of the plug then install the cable in the BNC plug so that the center wire is threaded through the plug center opening Before tightening the center wire securing screw make sure the center wire comes out through the plug center opening 4 Screw the adaptor onto the plug English 7 CONNECTIONS AND INSTALLATION E Basic connections for monitoring or recording The peripheral devices VCR monitor etc and cables are sold separately 1 Make the video signal connection between the camera and the monitor or time lapse VCR 2 Plug the AC adaptor to a wall outlet Adjust the picture on the monitor using the Brightness and Contrast controls Fig 2 nN e gt co lt E Hr VIDEO IN Time lapse VCR VIDEO OUT VIDEO IN sold separately Monitor sold separately
8. e sure that the camera is used correctly If it still does not perform correctly please consult your dealer or a Sanyo Authorized Service Center E No picture on the monitor screen s the power turned on to all connected devices Is the voltage correct Are all the signal connecting cables correctly connected s the lighting sufficient The picture is not dear s the monitor correctly adjusted s the lens focus correctly adjusted Are the lens surfaces clean f there is dust or finger prints on the lens the image quality will deteriorate To clean the lens use a soft cloth or a commercially available lens cleaning set SERVICE This camera is a precision instruments and if treated with care it will provide years of satisfactory performance However in the event of a problem the owner is advised not to attempt to make repairs or open the cabinet Servicing should always be referred to your dealer or Sanyo Authorized Service Center SPEC ICATIONS EIA standard 525 TV lines 30 frames sec Temperature 20 C 60 C Humidity less than 70 RH 525 TV lines 60 field sec 2 1 interlace Interline transfer method 1 3 inch solid state CCD 537 H x 505 V 510 H x 492 V Line lock 400 TV lines horizontally 350 TV lines vertically 1 0 V p p 75Q screw on terminal More than 50 dB Minimum required illumination O lux Electronic iris range 1 60 to 1 80 00
9. la Classe B est conforme a la norme NMB 003 du Canada Changes or modifications not expressly approved by Sanyo may This installation should be made by a qualified service person and void the user s authority to operate this camera should conform to all local codes English 1 CONTENTS PRECAUTIONS isinin 3 PARTS NAMES AND FUNCTIONS cscssssssstecssessssecssessstecssesssseessessasees 4 CONNECTIONS AND INSTALLATION sssrin 6 SETTINGS AND ADJUSTMENTS sssssssssssecssscsssessssesssessseesssessseessseess 9 TROUBLESHOOTING ssscssssscssessssesssessssesssessseesssessseesssessseesssessseessseess 9 SPECIFICATIONS ignani bh cacedacaveapsescarsanvuneeate 10 Accessories Q Verticaliholder plat ssisnypresann a 1 pe p gt FEATURES e Built in interline transfer method 1 3 CCD approx 270 000 picture elements e Low smear anti blooming low lag no burning and no geometric distortion using the CCD solid state image device e Built in fixed focal lens F 2 0 f 3 8 mm e 100 solid state components giving excellent immunity to shock and vibration e Not subject to interference from magnetic or electrostatic fields e Built in IR LED by very required mininum illumination is approx O lux at 4 5 m e Horizontal resolution more than 400 TV lines e Power supply 24 V AC operation 2 English PRECAUTIONS E in case of problem Do not use the camera if smoke or a strange odour comes from the unit o
10. nlight as that could cause deformation discoloration or other damages Be careful when installing close to the ceiling in a kitchen or boiler room as the temperature may raise to high levels Install where the temperature range will stay between 10 C and 50 C no condensation E Ceaning e Dirt can be removed from the cabinet by wiping it with a soft cloth To remove stains wipe with a soft cloth moistened with a soft detergent solution and wrung dry then wipe dry with dry soft cloth Do not use benzine thinner or other chemical product on the cabinet as that may cause deformation and paint peeling Before using a chemical cloth make sure to read all accompanying instructions Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time as that may cause damage or paint peeling PARTS NAMES AND FUNCTIONS Hood lens Foausring The focus does not need adjustment for subjects 1 m and more from the lens If the subject is closer than 1 m turn the focus ring to adjust the focus as necessary See page 9 Lens Lens cover This cover will protect the lens from dust and damage 24V AC input terminal 24 V AC GND With this camera use only the 24 V AC power adaptor model No VPT 115 available from Sanyo E Power supply connections Use a 3 wire grounded cable 22 AWG or more and connect as shown by the illustration CAUTION e To
11. prevent camera and or AC adaptor failure pay close attention polarity when making the connections e To prevent fire hazard any UL listed wire rated VW 1 should be used for the 24 V AC cable input terminal 4 English PARTS NAMES AND FUNCTIONS Camera mounting screw hole 1 4 20 UNC When mounting the camera to the mounting bracket use this installation hole Lens cover fixing screw GND ground terminal screw Loosen the GND terminal screw insert the coaxial cable into the clamp and tighten the GND terminal screw VIDEO OUT teminal screw Align the centre wire of the coaxial cable with the VIDEO OUT terminal then first tighten the cable clamp and then the VIDEO OUT terminal screw e Cable type RG 6U 5C 2V The view angle of this camera is as follows Horizontal 71 Vertical 53 Diagonal 90 To adjust the camera angle use the camera mounting bracket sold separately English 5 Line phase volume When using a camera switcher to connect 2 cameras or more to one monitor there may be a vertical roll of the images when switched In such a case set as described below Switch the display on the monitor from camera 1 to camera 2 Adjust the LINE PHASE volume on camera 2 until the vertical roll of the image stops If more than two cameras are used please repeat this procedure for all the cameras CAUTION If the vertical roll cannot be corrected by setting the LINE
12. r if it seems not to function correctly Disconnect the power cord immediately and consult your dealer or a Sanyo Authorized Service Centre E Do not open or modify Do not open the cabinet as it may be dangerous and cause damage to the unit For internal settings and repairs consult your dealer or a Sanyo Authorized Service Centre E Do not put objects inside the unit Make sure that no metal objects or flammable substance get inside the camera If used with a foreign object inside it could cause a fire short circuits or damages If water or a liquid gets inside the camera disconnect the power cord immediately and consult your dealer or a Sanyo Authorized Service Centre Be careful to protect the camera from rain sea water etc E Be careful when handling the unit To prevent damages do not drop the camera or subject it to strong shock or vibration E Install away from electric or magnetic fields If installed close to a TV radio transmitter magnet electric motor transformer audio speakers the magnetic field they generate will distort the image English 3 E Protect from humidity and dust To prevent damages to the camera do not install it where there is greasy smoke or steam where the dampness may get too high or where there is a lot of dust E Protect from high temperatures Do not install close to stoves or other heat generating devices such as spotlights etc or where it could be subject to direct su
13. to assume for it any other obligation or liability THE DURATION OF ANY WARRANTIES WHICH MAY BE IMPLIED BY LAW INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS IS LIMITED TO THE TERM OF THIS WARRANTY IN NO EVENT SHALL SFC BE LIABLE FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE ATTENTION For your protection in the event of theft or loss of this product please fill in the information below for you own personal records Model No Serial No Located on back or bottom side of unit Date of Purchase Purchase Price Where Purchased 21605 Plummer Street 1AC6P1P1829 Chatsworth California 91311 L73E4 US 1098NI Printed in Japan INFORMATION TO USER Sa fe ty Guard This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against THIS SYMBOL INDICATES THAT THERE ARE harmful interference in a residential installation
Download Pdf Manuals
Related Search