Sanus Systems PFV59S User's Manual
Contents
1. remaining of the shelf pins into the left side and back Lower the glass onto the shelf pins NOTE We recommend that all contents stored in or on this item of furniture be removed before shifting it The manufacturers will not be held liable for damage caused when furniture is shifted without first removing its contents If furniture is shifted we recommend that it is lifted not dragged2. 204 x 4 MH1169A0 x 1 RRE P816192 x 4 not to scale Q Bump on Cable Ducts P840022 x 18 P840200 x 4 not to scale a gray black Back edge Base underside Fasten 6 glides to the base as shown Note that there are 3 gray and 3 black glides Use gray glides at front of the base if the stand is going to be placed on a light colored floor Use Black glides at the front if the stand is going to be placed ona dark colored floor Large wooden dowels x 4 Left front panel Right front panel x6 Screw 3 connector rods into holes in left and right front panels as indicated above Press fit 2 large wooden dowels into large holes in left and right panels as shown Left side panel Right side panel lo O p Small wooden dowels T x12 a 9 0 o 9 Press fit small wooden dowels into left and right sides as shown above Right side panel p HE Qay D Insert cams into large holes in left and right sides as shown Make sure arrows on the cams point towards the corresponding cam holes along the edges of the panels Screw 4 connector rods into holes indicated in back panel Screw 4 connector rods into holes in the base as indicated above Insert 2 cams into large holes in the base as shown above Cable duct Press f
3. BUS5306 PLATINUM FURNITURE MODEL PFV59s Digital TV Stand Assembly Instructions Congratulations and thank you for purchasing your new Sanus Platinum Furniture Product If you have any questions regarding this or any other Sanus product please contact our customer service department at 800 359 5520 or www sanus com It is not necessary to contact the retailer with any questions or problems as parts can be sent directly to you Please follow these assembly instructions This will save you time make assembly easier and prevent possible damage to your new Digital TV Stand Assistance may be required for some assembly procedures Correct assembly is your responsibility BUS5306 We recommend that the unit is assembled on a soft surface such as carpet Please record your serial number in the space provided below and retain this manual for future reference Serial No This unit was manufactured using ISO 9000 certified systems For improvement purposes design and specifications are subject to change without notice SA NU SIS YO TEMS THE UNION OF FORM AND FUNCTION UNPACK AND IDENTIFY PARTS Angle ee Thin side Left side Long rail Left front Right side Glass shelf J M Steel bracket Base Thin side aa Right front PART NUMBER Glide gray black PART DESCRIPTION Base Left side Right side Thin side Right front Left fr
4. it the sides to the back as shown above Turn the cams clockwise to tighten Press fit 4 cable ducts into large holes in the back as shown Wy i gt E Assistance may be needed for this step Turn Cams clockwise to tighten Press fit the sides and back assembly onto the base as shown Turn the cams clockwise to tighten Fasten the back to the base as shown above STEP 10 Note position of rebate VW 3s Assistance may be needed for this step Hold the long rail in between the sides as illustrated Insert the black barrel nuts into the holes in the long rail Ensure the holes in the sides are aligned with the holes in the long rail Fasten the sides to the long rail as shown STEP 11 Press fit the front panels to the sides and base as shown Turn the cams clockwise to tighten STEP 12 NG Adjusting screw x 4 Thin side Slide thin sides down slots in front panels and back ensuring silver surfaces face out Screw each adjusting screw into sides by half of it s visible threaded length then once this is done tighten all 4 Adjusting screws fully into sides STEP 13 Fit the long steel bracket into the rebate in the long rail and in the grooves in the sides as shown above Ensure the bracket is equally distanced from the sides on both ends Once the b
5. ont Long rail Back Glass top Glass shelf Steel bracket Angle bracket Cable duct Gray glide Black glide Hardware pack 2 1 1 1 1 1 1 1 2 4 3 3 1 M20205A1PO M20206A1ZS M20207A1ZS M20208A1ZS M20209A1ZS M20210A1ZS M20211A1ZS M20212A1PO M20213A1PO M20214A1PO P816190 P816191A P840200 P815034A P815034 MH1181A0 TOOLS REQUIRED PHILLIPS No 2 SCREWDRIVER CUSTOMER SERVICE INFORMATION IN THE UNLIKELY EVENT OF PARTS BEING FAULTY OR MISSING CHECK PACKAGING REPLACEMENT PARTS CAN BE OBTAINED BY CALLING THE TOLL FREE NUMBER WITHIN 14 DAYS OF PURCHASE TOLL FREE NUMBER 800 359 5520 USA ONLY THE FOLLOWING INFORMATION MUST BE SUPPLIED IN FULL 1 YOUR NAME ADDRESS AND TELEPHONE NUMBER 2 PRODUCT MODEL NAME NUMBER AND COLOR 3 DESCRIPTION PART NUMBER AND QUANTITY OF REQUIRED PARTS 4 PURCHASE DETAILS STORE THE UNIT WAS PURCHASED FROM DATE OF PURCHASE 5 SERIAL NUMBER OF THE UNIT PURCHASED LOCATED ON REAR OF UNIT Hardware Contents CAUTION There are many small components used in the construction of this unit These loose items should be kept away from young children while assembling your unit Scale 1 1 unless stated otherwise Shelf pin P840048 x 6 P860034 x 9 P860071 X 6 P860068 X 5 P860211 x 2 Small wooden Barrel nut Connector rod Cam Large wooden dowels dowel pack P840050 x 2 P820016T x 14 P820015T x 14 P800
6. racket is adjusted in the sides fasten it to the long rail using the screws shown above It is important that you hold the long rail against the steel bracket as you tighten the screws STEP 14 Bump on self adhesive Attach 18 bump ons to top surface of the back sides front rails and steel bracket where shown above SY X Assistance may be needed for this step When placing the glass top on the unit pay attention to the following tips Ensure painted side is facing down Back edge of the glass top must be flush with the back panel Glass top s overhang at the left side must match that of the right side Lift the glass when repositioning it do not drag it as it could damage your glass SL H o Ten edge Above is the top view of the cabinet indicating where the glass top should rest on the cabinet STEP 15 Fasten the angle brackets to the back as shown above Note the angle brackets are essential for the strength of the stand Frosted side should face down Insert 2 shelf pins into the bottom holes in the right side Place a piece of polystyrene from the pack onto the base as shown above Alternatively you could use a soft rag Tilt the glass to one side and rest it on top of the polystyrene Then carefully push the glass inside the cabinet and rest the right side on the shelf pins Then raise the left side of the glass up and insert the
Download Pdf Manuals
Related Search