Samsung SSA-S2000W User's Manual
Contents
1. I lost the Master Card and could not register or delete the card or change the settings You must initialize the product if you want to change the device settings without the Master Card or PIN Initializing the product will restore all your settings regarding the Master Card and user cards to the factory default Initialization using the extemal cable Tum off the product and detach it from the wall Tum off the product and detach it from the wall J Tum on the product and check the initial state LED indicators blink with the increasing bell sound Disconnect the two short circuited lines and tum off the product Hardware Forcible Initialization use this only if initializing the product with the extemal cable is not possible um off the product and detach it from the wall Loosen the 4 screws on the rear to remove the bezel um on the product and connect the initialization jumper switch under the LED Check the initialization state 3 LED indicators are blinking simultaneously Tum off the product and use the 4 screws to attach it back to the wall Install and use the product as usual For more information refer to the initialization section in the user manual You must consult with a qualified technician for the removal and initialization process of the product v v V V 2 Ifthe problem persists after you have followed the procedures above2. 1 Present the Master Card to the device ee 2 Press Button B 3B and Button in sequence and press ENT 3 Enter the two digit retry count and press 5 e You can specify a number from 00 to 99 e The retry count for an unregistered ID is defaulted to 05 24_ Basic Setup TO SPECIFY THE KEYPAD INPUT SUSPENSION TIME IF THE RETRY COUNT WITH AN UNREGISTERED ID EXCEEDS THE LIMIT Samsun 1 Present the Master Card to the device 2 Press Button B and Button o in sequence and press B 3 Enter the two digit keypad input suspension time unit minute and press e The default is set to 01 You can specify a time from 01 to 99 minutes dNlas SISvd L You can specify the time of the keypad input suspension followed by an alarm if an unregistered user keeps trying to open the door for certain times the code number is set to 82 TO SPECIFY THE DELAYED START TIME INSECURE MODE samsune 1 Present the Master Card to the device 2 Press Button 8 and Button o in sequence and press 3 Enter the two digit delayed start time unit minute and press e The default is set to 00 Lf See the table below for your reference When the last person set the Secure mode before exiting the office the external sensors will SEGUE Mede get activated since then If the external sensors get activated right after you set the Secure mode your motion will be Delayed St
3. 4 Present the Master PIN number to the device again and the device will switch o normal mode lt Master PIN gt f no input is made for 20 seconds the device will switch to normal mode SAMSUNG samsune 7 wee lt User Number gt lt User Number gt lt Master PIN gt REGISTERING CARDS IN RF CARD PIN COMBINATION MODE Ensure that you must have registered the Master Card and the device is specified in RF Card PIN combination mode 1 Present the Master Card to the device When the mode is specified only the green LED indicator flashes 2 Press Button and Button o in sequence and press When the device enters Standby only the red LED indicator flashes 3 Present cards or PIN numbers 4 6 digits to register with the device one after another and the device will register them with a beep Repeat this step if you want to register multiple cards or PIN numbers 4 Present the Master PIN number to the device again and the device will switch to normal mode f no input is made for 20 seconds the device will switch to normal mode LY The door may be accessed in two ways using the card or the PIN number 22_ User Management TO DELETE A REGISTERED CARD OR PIN NUMBER Ensure that you must have registered the Master Card or the Master PIN number and the device is specified in a certain mode This is applicable in all modes SAMSUNG 1 Enter the Master Card or Master PIN BA When the m
4. 2 Keypad ie to configure or release settings as appropriate or enter a card 8_ Product Introduction CABLE COLOR SCHEME 2 PIN Connector 1 0 Pins Signal Cable Color Power 12V DC 12V Red Earth grounding GND Black 10 PIN Connector 1 0 Pins Signal Cable Color Door Control Relay NC NC RL1 Blue with White stripes Door Control Relay COM COMIRL1 Gray with Red stripes Door Control Relay NO NO RL1 White with Red stripes Alarm Relay NC NC RL2 Purple with White stripes Alarm Relay COM COMIRL2 White Alarm Relay NO NO RL2 Purple Exit Button EXI Orange Door Contact Sensor CONTACT Yellow with Red stripes Aux Input 1 AUXIN 1 Green Aux Input 2 AUXIN 2 Green with White stripes 7 PIN Connector 1 0 Pins Signal Cable Color Wiegand Data Input 0 DATA 0 Pink Wiegand Data Input 1 DATA 1 Sky blue TTL Output TIL Orange with White stripes Chime Bell Output CHI Brown with White stripes Aux Input 3 AUXIN 3 Green with Red stripes RESERVED 1 Blue with Red stripes RESERVED 2 Yellow with Red stripes 3 PIN Connector 1 0 Pins Signal Cable Color RESERVED 1 Black with White stripes RESERVED 2 Red with White stripes RESERVED 3 Black English _ 9 NOILONGOYLNI LONGOHd installation and external connection INSTALLING THE REAR TEMPLATE 6 32 hole La O10 EJE O ring O ring
5. contact a designated service center English _ 47 troublesnooting Problem SSA S2000 can recognize a presented RF card but can not recognize the RF card number using the keypad 1 Action Check if the buzzer sounds when you press a key lf you hear the buzzer sound Master Card or PIN 4 6 digits Mode 03 or 05 ENT Enter the command to enable the keypad input 73 ENT For more information refer to the section of enabling or disabling the keypad input for a card number in the user manual If you hear the buzzer sound after a certain time The keypad input will be suspended for one minute default if you enter unregistered numbers in 5 consecutive times default To change the retry count for an unauthenticated access Master Card or PIN 4 6 digits Mode 03 or 05 ENT Enter the command to set the retry count for an unauthenticated access 82 ENT v Enter a new retry count two digits ENT ex 10 ENT gt the retry count is 10 For more information refer to the retry count setting section in the user manual To change the keypad suspension time Master Card or PIN 4 6 digits Mode 03 or 05 ENT Enter the command to change the keypad suspension time 60 ENT v Enter a new time two digits ENT ex 10 ENT the keypad input will be suspended for 10 minutes For more information refer to the applicable section for the keypad suspension
6. repeat Step 1 above select the lt B gt buttons and press Lf The default is set to switch from HIGH 5V to LOW OV TO SPECIFY THE INPUT MODE FOR THE EXIT BUTTON You can specify an operation for the Exit button when it switches from LOW OV to HIGH 5V 1 Present the Master Card to the device 2 Press Button g and Button p and Button e To release the setting press the B B gt buttons and press ONILLAS GAONVAGV LY buttons and press The default is set to switch from HIGH 5V to LOW OV TO SPECIFY THE INPUT MODE FOR THE DOOR CONTACT SENSOR You can specify an operation for the Door Contact Sensor when it switches from LOW OV to HIGH 5V 1 Present the Master Card to the device Samsunc 2 Press Button G and Button B in sequence and press To release the setting repeat Step 1 above select the lt gt buttons and press Lf The default is set to switch from HIGH 5V to LOW OV English _ 37 additional features MUTE You can mute the keypad tone or melody in normal operation 1 Present the Master Card to the device 2 Press Button B and Button Oo in sequence and press e To release the setting repeat Step 1 above select the B B gt buttons and press LY By default it is set to enabled TO SPECIFY THE USE OF THE TAMPER ALARM You can maintain the alarm setup in normal operation and rel
7. E E 3 1 2 hole A 2 O E O ring 8 6 32 hole 2 8 a N QN 1 52 38 5mm 1 52 38 5mm 3 03 77mm Oo Once the main unit is fixed with the rear panel it will not be loosened Please check if the device is operating before fixing it If you try to remove the rear panel once it is fixed the lock parts of the rear panel will break resulting in a situation where the whole rear panel must be replaced 10_ Installation and External Connection CABLE SELECTION 1 O ee 8 7 8 8 DC12V amp 0 e amp Power Supply Ball 8A 82000 aS Ey RF Reader Sensor Input Lock Alarm Item Cable Type Power DC12V e 1 E Belden 9409 18 AWG 2 Conductor Unshielded Reader power and data Belden 9512 22 AWG 4 Conductor Shielded External Reader gt This Product Belden 9514 22 AWG 8 Conductor Shielded Door Contact Sensor Belden 9512 22 AWG 4 Conductor Shielded 3 Exit Button Fil Input pare a Bee Belden 9514 22 AWG 8 Conductor Shielded Door Lock 4 Alarm Device Belden 9409 18 AWG 2 Conductor Unshielded Lock Alarm gt This Product Oo The cables should be thick enough to allow the maximum current consumed by the reader English _ 11 NOILOANNOO TWNYALXS ANY NOLLVTIVLSNI installation anc_extermal connection BYPASS DIODE CONNECTION If you connected an inductor door locks or alarm device to the output relay there should
8. Secure mode 50 o Door Relay 01 m Operation port setting value Output Port Setting Value 51 U Operate the door relay onl 01 pi y only X3 Operate the alarm relay only 02 If the alarm relay and the TTL output operate in Secure mode Operate the TTL output only 04 Secure Mode 00 Operate the door relay and TTL output 05 Alaim Relay TTL 400 Output Port Setting Value 06 Operate the alarm relay and TTL output 06 TO SPECIFY THE OUTPUT TIME IF THE CARD IS AUTHENTICATED You can specify the output time if the card ID is authenticated When the card ID is authenticated the door relay and the TTL output operate for a set time 1 Present the Master Card to the device 2 Press Button B and Button in sequence and press 3 Enter the two digit door open time and press 4 Specify the two digit TTL output time and press z e For instance if you set the door open time to 03 and TTL to 00 the door relay operates for 3 seconds for an authenticated card ID e By default the door relay operates for 03 seconds while the TTL output works for 00 second in normal and Secure modes e You can specify from 10 to 99 English _ 29 O time setuo TO SPECIFY THE OUTPUT TIME IF THE CARD IS NOT AUTHENTICATED You can specify the output time if an unregistered card or PIN number fails in getting authenticated 1 Present the Master Card to the device samsons 2 Press Button B twi
9. a beep If you don t want to register the cards right now simply jump to Step 5 above without through Step 4 above 5 Present the registered Master Card to the product once again 6 The device enters Standby mode with only the orange LED indicator flashing 18_ Reader Mode Setup READER MODE SETUP RF P W No Master Card or Master PIN is ever registered If you remember the Master Card or the Master PIN was registered initialize the product and try again 1 When you turn on the product all of the 3 LED indicators will flash with a beep e No flashing of the 3 indicators denotes that the reader mode is already specified 2 Press Button Go and Button B in sequence and press 3 3 Present a card that you want to register as the Master Card to the device When the Master Card is registered only the red LED indicator flashes dN13S AGOW Y3dAvJ4 4 Present a card to the device enter the 4 6 digit password and press f you don t want to register the cards right now simply jump to Step 5 above without through Step 4 above 5 Present the registered Master Card to the product once again 6 The device enters Standby mode with only the orange LED indicator flashing READER MODE SETUP PIN ONLY No Master Card or Master PIN is ever registered If you remember the Master Card or the Master PIN was registered initialize the product and try again 1 When you tum on the product all of the 3 LED
10. it securely and firmly The fall of controller may cause personal injury Do not place conductive objects e g screwdrivers coins metal parts etc or containers filled with water on top of the controller Doing so may cause personal injury due to fire electric shock or falling objects Do not install the unit in humid dusty or sooty locations Doing so may cause fire or electric shock If any unusual smells or smoke come from the unit stop using the product In such case immediately disconnect the power source and contact the service center Continued use in such a condition may cause fire or electric shock If this product fails to operate normally contact the nearest service center Never disassemble or modify this product in any way SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair 10 When cleaning do not spray water directly onto parts of the product Doing so may cause fire or electric shock CAUTION i Do not drop objects on the product or apply strong blows to it Keep away from a location subject to excessive vibration or magnetic interference Do not install in a location subject to high temperature over 50 C low temperature below 10 C or high humidity Doing so may cause fire or electric shock 3 If you want to relocate the already installed product be sure to turn off the power and then move or reinstall it Remove the power plug from the outl
11. occur a voltage surge while the inductor is turning on and off If you do not connect a reverse diode to the relay the surge voltage will cause damage to the electric circuit of the controller To reduce this surge it is recommended to connect a reverse diode between the devices I samsune wee DC Cathode Anode eee ree N m JOG DC 1N4004 1N4007 or equiv Lock Alarm 1 0 CONNECTION Input Connection 1 samsunc Door Contact Sensor Green with red stripes GND Exit Button Orange line GND e 7 8 rw ee Bol Door Contact Sensor DC 12V Power Supply i Exit Button iii 1 Connect the DC 12V of the power supply unit to the red line 2 Connect the GND of the power supply unit to the black line Exit Button Connection 1 Connect one line of the Exit button to the orange line 2 Connect the other line of the Exit button to GND Door Contact Sensor Connection 1 Connect one line of the door contact sensor to the yellow with red stripes 2 Connect the other line of the door contact sensor to GND Auxiliary Input Device Connection AUX 1 green AUX 2 green with white stripes AUX 3 green with red stripes 1 Connect one line of the external input device to AUX 1 AUX 2 or AUX 3 2 Connect the other line of the external input device to GND 12_ Installation and External Connection Output Connection Connect the 10 pin and 7 pin
12. to RF ONLY mode 01 and PIN ONLY mode 03 and RF PIN combination mode 05 which enables you to open the door by simply pressing without the need of the PIN number This is useful for the normal business hours when the door entries and exits occur frequently 1 Present the Master Card to the device 2 Press Button a and Button B in sequence and press i e To release the QUICK mode repeat Step 1 above select the B 3 gt buttons and press e The default is set to not used SAMSUNG ee ee 8 TO SET OR RELEASE THE TOGGLE MODE FOR THE DOOR RELAY In the Toggle mode the door opens if it is closed or vice versa by presenting a registered card or entering the PIN 1 Present the Master Card to the device 2 Press Button oO and Button 5 in sequence and press i e To release the Toggle mode repeat Step 1 above select the B g buttons and press e The default is set to not used 28_ Basic Setup SAMSUNG ee 8 as 0 amp O time setup gt Output Port Setting Table You must specify the port settings using whatever combination of the followings if you want the device to operate in Secure mode or normal Secure mode Port Setting Value Example e Operation mode setting value EX1 If only the door relay operates in normal and Operate only in Secure mode 00 Secure modes Normal and Secure modes 50 m Operate in normal mode and
13. 1S7 S0010 standalone RAD Access Controller user manual imagine the possibilities Thank you for purchasing this Samsung product To receive more complete service please visit our website www samsungsecurity com safety information RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit important operating and maintenance servicing instructions in the literature t This exclamation point symbol is intended to alert the user to the presence of accompanying the appliance WARNING e To reduce the risk of fire or electric shock do not expose this appliance to rain or moisture WARNING f Be sure to use only the standard adapter that is specified in the specification sheet Using any other adapter could cause fire electrical shock or damage to the product Incorrectly connecting the power supply or replacing battery may cause explosion fire electric shock or damage to the product Do not connect multiple controllers to a single adapter Exceeding the capacity may cause abnormal heat generation or fire Securely plug the power cord into the power receptacle Insecure connection may cause fire When installing the controller fasten
14. 6 digits to register with the device one after another and the device will register them with a beep If you don t want o register the cards right now simply jump to Step 5 above without through Step 4 above 5 Present the registered Master Card to the product once again 6 The device enters Standby mode with only the orange LED indicator flashing ENABLING KEYPAD INPUT FOR THE CARD NUMBER Ensure that you must have registered the Master Card 1 Present the Master Card to the device samsune 2 Press Button eG and Button B in sequence and press 5 e Repeat Step 1 above to release the specified mode press Button 7 and Button in sequence and press i L You can set the device to allow you to control the door by entering the 8 digit card number using the keypad The default is Keypad Input Disabled 20_ Reader Mode Setup user management TO REGISTER CARDS IN RF ONLY MODE Ensure that you must have registered the Master Card and the device is specified in RF ONLY mode 1 Present the Master Card to the device When the mode is specified only the green LED indicator flashes aS 2 Press Button rm and Button o in sequence and press When the device enters Standby only the red LED indicator flashes 3 Present a card to the device it will be registered with a beep Repeat this step if you want to register multiple cards 4 Present the Master card to the device again and the de
15. EC Directive 2006 66 If batteries are not properly disposed of these substances can cause harm to human health or the environment To protect natural resources and to promote material reuse please separate batteries from other types of waste and recycle them through your local free battery return system AB82 02555A
16. ON OFF ON OFF TTL Output Chime Bell Output OFF ON OFF ON Wiegand Data0 Wiegand Data Oo In the 26 bit Wiegand output mode you can not initialize the product by short circuiting cables INITIALIZATION If you have the Master Card registered you can use it to initialize the device 1 Present the Master Card to the device 2 Press the 9 button twice and press 3 The system will restore the factory default settings with all LED indicators blinking 7 mee L Initializing the system will lose all data f the product works abnormally use initialization to restore the default settings 16_ Initialization FORCED INITIALIZATION WITH EXTERNAL LINE 1 Turn off the product shortcircuit between the green line and e the orange line with white stripes and turn it back on 5 2 When the initialization is completed 3 LED indicators are Green Bio OF Cc blinking with a beep Orange with white stripes Oe Connect gt Sho g 3 Restore the connection of the two lines back to their original state HARDWARE FORCIBLE INITIALIZATION This is to initialize the product forcibly by disassembling it Use this method only if you have lost the Master Card or the password or if the forcible initialization with the external line failed 1 Turn off the product and detach it from the installation site then loosen the screw x4 on each corner to disassemble it as shown 2 Apply
17. ON TIME You can specify the chime bell operation time 1 Present the Master Card to the device re 2 Press Button B and Button 8 in sequence and press B 3 Specify the two digit operation time unit second and press x ONILLAS GAONVAGV LY The default is set to 05 second You can specify a time from 00 to 99 seconds TO SPECIFY THE INPUT MODE FOR AUX 1 You can specify an operation for the auxiliary port 1 when it switches from LOW OV to HIGH 5V 1 Present the Master Card to the device 2 Press Button 6 and Button o in sequence and press e To release the setting repeat Step 1 above select the B B gt buttons and press L The default is set to switch from HIGH 5V to LOW OV English _ 35 acivancec_setting TO SPECIFY THE INPUT MODE FOR AUX 2 You can specify an operation for the auxiliary port 2 when it switches from LOW OV to HIGH 5V 1 Present the Master Card to the device SAMSUNG 2 Press Button and Button 8 in sequence and press To release the setting press the B p gt buttons and press L The default is set to switch from HIGH 5V to LOW 0V TO SPECIFY THE INPUT MODE FOR AUX 3 You can specify an operation for the auxiliary port 3 when it switches from LOW OV to HIGH 5V 1 Present the Master Card to the device cme 2 Press Button G and Button B in sequence and press P e To release the setting
18. al I O Pins SSA SS2000 has 5 input ports and 4 output ports installed 2 relay and 2 TTL outputs The input ports can receive signals from the Exit button and the Door Contact sensor while the two relays can be connected to the door lock and the alarm device One of the TTL output ports can function as a chime bell in connection with the door bell Duress Alarm This is used in a situation where you should open the door inevitably by a robber insisting to do so Entering the two digit duress alarm password with pressing the QJ button and recognizing the registered card or card number can open the door normally while you can set to produce the TTL signal notifying the door is forcibly opened Limited Access Tries for an Unregistered Card You can specify the limit of times to try accessing the door and the suspended operation time of the keypad for an improper access 6_ Product Introduction WHAT S INCLUDED Check if the following items are included in the product package Main Unit Uh wean POTD 3 5 x 40mm Screws x4 3 5 x 12mm Screws x4 6 x 30mm Plastic Anchors x4 Master Card Master Card x1 Template Quick Guide Quick Guide Cables x4 UF4004 1N4001 4007 English _ 7 NOILONGOYLNI LONGOHd oroduct introduction AT A GLANCE Front View SAMSUNG SSA S2000 1 System Status LED Indicates the operation status of the system
19. art detected before you can get out of the secure area which will trigger the alarm Thus it is recommended to set the Secure mode to get activated after a certain time Enter the delayed start time by the minute the sensor operation in Secure mode must have been specified in advance Refer to Alarm Operation Time for Auxiliary Input on pages 31 32 English _ 25 basic setup TO SPECIFY THE OPERATION TIME OF THE DOOR CONTACT SENSOR The Door Contact sensor detects the opening of the door If the door is forcibly opened by an unregistered user the Door Contact Sensor will perform the predefined alarm operation after the set time For setting the alarm operation time refer to the alarm output for an input error of the Door Contact Sensor on page 31 1 Present the Master Card to the device 2 Press Button B and Button oO in sequence and press 3 Enter the two digit operation time unit second and press g e The default is set to 00 second which means the Door Contact Sensor is disabled e You can specify from 01 to 99 TO SPECIFY THE LIMITED TIME FOR THE KEYPAD INPUT When it passes a certain time during your setting using the keypad all your settings will be ignored and return to the initial state Specify the delay time between the input of the last key and restoring the previous state 1 Present the Master Card to the device ind 2 Press Button B and Button B in sequence and pr
20. card and user cards as usual because the product is in the initial state SSA 2000 modes available Mode Number ENT JRF Only 01 ENT JRF PW 02 ENT v PIN Only 03 ENT VRForPIN 05 ENT Master Card or PIN 4 6 digits Mode 03 or 05 ENT Enter the user card or PIN number and provide the password according to the mode Master Card or PIN 4 6 digits Mode 03 or 05 ENT For more information about registering the Master Card and the user card refer to the initial setup section in the user manual If this happens while the product is operating normally with the Master Card and user card registered Product malfunction Power OFF ON If the problem persists perform the initialization process for the next step For more information about initializing the product refer to the initialization section in the user manual If the problem persists after you have followed the procedures above contact a designated service center The product just switches to normal operation mode while am registering a user in a set mode or configure the settings If no key input is entered within 20 seconds in a set mode the product will switch to normal operation mode automatically normal operation English _ 45 SNILOOHSATENOUL troublesnooting Problem I can not register an additional user card or PIN 1 Action Check if the product is installed proper
21. ce and press x 3 Refer to the output port table on page 29 and specify a desired output mode If you want the alarm relay alone to operate in normal and Secure modes for an unauthenticated card select the B 2 gt buttons and press 4 Enter the two digit door relay output time and press 3 5 Enter the two digit alarm relay output time and press i 6 Enter the two digit TTL output time and press e You can specify a two digit time from 00 to 99 seconds By default only the alarm relay operates for 02 seconds in normal and Secure modes LY Other output ports that are not specified for the output mode will not be activated For instance if you set the output mode to 5 2 and assign the operation time for each output device by following the steps 4 5 and 6 above only the alarm relay will operate TO SPECIFY THE DURESS TTL OUTPUT If you enter the Duress code and present a registered card the TTL output operates Specify the TTL operation time for this purpose For the Duress code refer to Duress Alarm on page 24 1 Present the Master Card to the device 2 Press Button 8 and Button G in sequence and press z 3 Specify the two digit TTL output time unit second and press e The default is set to 03 second You can specify a time from 00 to 99 seconds 30_ I O Time Setup TO SPECIFY THE ALARM OUTPUT FOR AN INPUT ERROR OF THE DOOR CONTACT SENSOR You can specify the output
22. connectors of the controller as follows EXIT S EXIT BUTTON CONTACT m _DOOR mq CONTACT AUX IN 1 CHIME z PIR SENSOR DOOR RELAY NO f0 Cathode Anode CHIME BELL 1N4004 1N4007 or equiv DOOR LOCK DC 12V POWER SUPPLY Door open POWER FAIL SAFE when the power is disconnected from the door lock Door Relay 1 Connect the relay COM line gray with red stripes for locking the door to DC 12V 2 Connect the relay NC line blue with white stripes for locking the door to the plus line of the door lock 8 Connect the minus line of the door lock to GND Door close POWER FAIL SECURE when the power is disconnected from the door lock Door Relay 1 Connect the relay COM line gray with red stripes for locking the door to DC 12V 2 Connect the relay NO line white with red stripes for locking the door to the plus line of the door lock 3 Connect the minus line of the door lock to GND Alarm Connection Alarm Relay 1 Connect the relay COM white for the alarm device to DC 12V 2 Connect the relay NO line purple for the alarm device to the plus line of the alarm device 3 Connect the minus line of the alarm device to GND Chime Bell Connection the chime bell operated by TTL level signal must be installed in advance 1 Connect the chime bell line brown with whit
23. d or PIN is not deleted X Action Check the operation status of the product 1 Check if the product works properly If the product operates normally and you have the Master Card or the PIN number If you have the card to delete laster Card or PIN 4 6 digits Mode 03 or 05 ENT Enter the command to delete the user 14 ENT Enter another card to delete if you have multiple cards to delete laster Card or PIN 4 6 digits Mode 03 or 05 m V V V i El If you have lost the card to delete But you know the card number Master Card or PIN 4 6 digits Mode 03 or 05 V V V V V V m SNILOOHSATENOUL Enter the command to enable the keypad input 73 laster Card or PIN 4 6 digits Mode 03 or 05 Enter the command to delete the user 14 ENT Enter another card to delete and press ENT if you have multiple cards to delete laster Card or PIN 4 6 digits Mode 03 or 05 ENT For more information about deleting the user card refer to the user deletion section in the user manual If you have lost the Master Card or PIN Registering or deleting the user card is not possible without the Master Card Initializing the product For more information about initializing the product refer to the initialization section in the user manual If the problem persists after you have followed the procedures above contact a designated service center m o m
24. e or a multimeter please consult with a qualified technician Remove the door lock from SSA S2000 and check the relay output of SSA S2000 Replace the door lock if the relay output of SSA S200 shows a normal state For more information refer to the door lock connection section in the user manual If the problem persists after you have followed the procedures above contact a designated service center English _ 49 SNILOOHSATENOUL oroduct specifications PRODUCT SPECIFICATIONS Item SSA S2000 User 512 Users Power Current DC 12V Max 110mA Reader Port External Reder Port 1ea 26bit Wiegand for Exit Reading Time Card 30ms Door Open Time 00 99 Sec Default 3Sec Input Port 5ea Exit Button Door Sensor Aux 1 2 3 2ea 2 Form C Relay Output COM NO NC DC12 18V Rating Max 2A Output Port tea Chime Bell Output DC5V Rating Max 500mA tea TTL Output DCSV Rating Max 20mA LED Indicator 3 LED Indicators Red Green and Orange Beeper Piezo Buzzer Keypad 12 Key Numeric Keypad with Back Lighting Operating Temperature 30 C to 50 C Operating Humidity 10 to 90 relative humidity non condensing Color Material Silver with Black Polycarbonate Dimension W x H x D mm 87 0 x 109 0 x 31 0 Weight 220g 50_ product specifications Correct Disposal of This Product Waste Electrical amp Electron
25. e stripes of the controller to DC 5V 2 Connect he GND line of the power supply unit to GND of the chime bell 3 Press 9 to aOctivate EthNeT chime bell English _ 13 NOILOANNOO TWNYALXS ANY NOLLVTIVLSNI installation and extemal connection EXTERNAL READER CONNECTION eee Wiegand DATAO Pink TEs TES Wiegand DATAO Sky blue amp amp Bell Proximity Reader Connection 1 Connect the DC 12V of the power supply unit to the plus line of the reader 2 Connect the GND line of the power supply unit to the minus line of the reader 8 Connect the Wiegand data input line O of the proximity reader to the purple line 4 Connect the Wiegand data input line 1 of the proximity reader to the sky blue line e For a list of compliant readers external readers see the followings Standard 26bit Wiegand format proximity reader 14_ Installation and External Connection intalization BASIC OPERATIONS Initial Status While the product is working normally the orange LED indicator blinks every one second Predefined Operation for a Registered Card When reading a registered card it opens the door with the melody samsune Wad NOILVZIIVILINI Exit Button Operation If you press the Exit button the door will be opened o Predefined Operation for an Unregistered Card When reading an unregistered card it produces an alar
26. e user will be required to correct the interference at his own expense IMPORTANT SAFETY INSTRUCTIONS Read these instructions Keep these instructions Heed all warnings Follow all instructions 1 2 3 4 5 Do not use this apparatus near water 6 Clean only with dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers or other apparatus including amplifiers that produce heat oO Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus 2 13 Unplug this apparatus when a card is used Use caution when moving the cart apparatus A combination to avoid injury from tip over 14 Refer all servicing to qualified service personne
27. ease it in case of a service repair requiring the dismantlement of the device You must set the alarm mode when you have installed the device For the alarm output port settings refer to To specify the alarm output port for the dismantled device on page 27 1 Present the Master Card to the device snusune 2 Press Button B twice and press D e To release the alarm setting for the dismantled device repeat Step 1 above select the B 9 gt buttons and press 3 LY The default is set to disabled You can release the alarm for the dismantled device by presenting the Master Card or a registered card 38_ Additional Features TO CHECK THE OUTPUT SPECIFIED FOR A REGISTERED CARD USER You can check the output setting that you specified in To specify the output time if the card is authenticated See page 29 Samsun 1 Present the Master Card to the device 2 Press Button B and Button 7 in sequence and press SSYNLVss TVNOILIGGV TO CHECK THE OUTPUT SPECIFIED FOR AN UNREGISTERED CARD USER You can check the output setting that you specified in To specify the output time if the card is not authenticated See page 30 1 Present the Master Card to the device 2 Press Button 3 and Button B and Button i English _ 39 additional features TO CHECK THE OUTPUT SPECIFIED FOR THE DOOR CONTACT SENSOR ALARM You can check the output setting that you specified in To s
28. ess i 3 Enter the two digit operation time unit second and press e The default is set to 20 second You can specify from 10 to 99 26_ Basic Setup TO SPECIFY THE ALARM OUTPUT PORT FOR THE DISMANTLED DEVICE Specify the alarm type for the dismantled device The alarm rings from the dismantlement of the device to the authentication of the Master Card or a registered card 1 Present the Master Card to the device 2 Press Button B and Button in sequence and press i 3 Provide the alarm output port and press i e The default is set to 02 alarm For the alarm output port settings refer to the output port table on page 29 e The alarm for the dismantled device occurs regardless of the operation mode of either Normal or Secure so you simply specify the operation port only To specify the operation port refer to the operation port settings in the output port setting table on page 29 TO OPEN OR CLOSE THE ENTRY DOOR cee Follow the step below If you want to keep the door open regardless of the authentication process using the Master Card or PIN 1 Present the Master Card to the device 2 Press Button oO and Button m in sequence and press f e To release opening the door repeat Step 1 above select the gt en B gt buttons and press f Be 8 es EDE English _ 27 dN13S SISsvd basic setup TO SET OR RELEASE THE QUICK MODE The QUICK mode is applicable
29. et when there is a lighting storm Neglecting to do so may cause fire or damage o the product _ Safety information Keep out of direct sunlight and heat radiation sources It may cause fire Install it in a place with good ventilation Avoid aiming the controller directly towards extremely bright objects such as sun on O on Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus 9 The Mains plug is used as a disconnect device and shall stay readily operable at any time FCC Statement This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Caution This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in ac cordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case th
30. ic Equipment Applicable in the European Union and other European countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal Correct disposal of batteries in this product Applicable in the European Union and other European countries with separate battery return systems This marking on the battery manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life Where marked the chemical symbols Hg Cd or Pb indicate that the battery contains mercury cadmium or lead above the reference levels in
31. in the user manual If the buzzer stays inactive Initialize the product Initializing the product will restore all your settings regarding the Master Card and user cards to the factory default 2 _ If the problem persists after you have followed the procedures above contact a designated service center The Exit button does not work at 1 Check if the Exit button is connected to SSA S2000 properly all Ensure that the Exit button is of the NO type 2 Check if the Exit button works normally Check the connection cable between the Exit button and SSA S2000 for any disconnection or short circuit Try to connect the two lines on the Exit button If SSA S2000 responds when you press the Exit button v Replace the Exit button it is defective If SSA S2000 does not respond at all v Initialize the product the product malfunctions or is damaged nitializing will restore all data settings to the default J For more information refer to the initialization section in the user manual If the problem persists after you have followed the procedures above contact a designated service center 48_ Troubleshooting Problem The external reader can the RF card but the RF card data will not be transferred to SSA S2000 or irrelevant data is transferred Action Check if the external reader is connected to SSA S2000 properly Check if the external reader works normally Check the connection cable between the e
32. indicators will flash with a Ue beep No flashing of the 3 indicators denotes that the reader mode is already ee specified ee 2 Press Button G and Button B in sequence and press When the mode is specified only the green LED indicator flashes 3 Enter the 4 6 digit Master PIN number and press When the Master PIN is registered only the red LED indicator flashes 4 Enter a PIN number to register 4 6 digits and press Repeat the step above if you want to register PIN numbers with the device in sequence If you don t want to register the PIN number right now simply jump to Step 5 above without through Step 4 above 5 Enter the 4 6 digit Master PIN number again and press 6 The device enters Standby mode with only the orange LED indicator flashing English _ 19 reader mode setup READER MODE SETUP RF PIN COMBINATION MODE No Master Card or Master PIN is ever registered If you remember the Master Card or the Master PIN was registered initialize the product and try again 1 When you turn on the product all of the 3 LED indicators will flash with a beep mee e No flashing of the 3 indicators denotes that the reader mode is already specified 2 Press Button o and Button B in sequence and press 3 Present a card that you want to register as the Master Card to the device When the Master Card is registered only the red LED indicator flashes 4 Present cards or PIN numbers 4
33. l Servicing is required when the apparatus has been damaged in any way such as powersupply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped English _ 3 NOILVINYOSNI ALJJVS contents PRODUCT INTRODUCTION INSTALLATION AND EXTERNAL CONNECTION INITIALIZATION READER MODE SETUP USER MANAGEMENT BASIC SETUP 4_ Contents oOND 21 21 22 22 23 24 24 25 25 26 26 27 Features What s included At a Glance Cable Color Scheme Installing the rear template Cable Selection Bypass Diode Connection 1 0 Connection External Reader Connection Basic Operations Wiegand Output Setup Initialization Forced Initialization with External Line Hardware Forcible Initialization Reader Mode Setup Reader Mode Setup Reader Mode Setup Reader Mode Setup Mode Enabling Keypad Input for the Card Number RF ONLY RF P W PIN ONLY RF PIN Combination anaana To register cards in RF ONLY mode Reglsterlng cards In a comblnatlon oF RF and P W modes to register cards In PIn mode reglsterlng cards In rF card Pin combinatlon mode to delete a reglstered card or PIn number Duress Alarm To specify the retry count for an unregistered ID To specify the keypad input suspension time if the retry count with an unregistered ID exceeds the limit To specif
34. ly and works normally In the initial setup of the product or after it is initialized Set the operation mode and register the Master card and user cards as usual because the product is in the initial state SSA 2000 modes available Mode Number ENT VRFOnly 01 ENT JRF PW 02 ENT J PIN Only 03 ENT J RForPIN 05 ENT Master Card or PIN 4 6 digits Mode 03 or 05 ENT Enter the user card or PIN number and provide the password according to the mode Master Card or PIN 4 6 digits Mode 03 or 05 ENT For more information about registering the Master Card and the user card refer to the initial setup section in the user manual If this happens when you try to register an additional card in normal operation mode Register the user card only as the Master Card is already registered Master Card or PIN 4 6 digits Mode 03 or 05 ENT Command for an additional card registration according to the operation mode JRFOnly 11 ENT JVRF PW 12 ENT JPINOnly 13 ENT vRForPIN 15 ENT Enter the user card or PIN number and provide the password according to the mode Master Card or PIN 4 6 digits Mode 03 or 05 ENT For more information about registering the user card refer to the additional user registration section in the user manual If the problem persists after you have followed the procedures above contact a designated service center 46_ Troubleshooting Problem The user car
35. m with the melody for two seconds 14 You can specify the use of the alarm and change the operation time Secure Mode Operation The person who exits the last can set the secure mode using the keypad Set Secure mode Press the 9 button twice and press Release secure mode Present and authenticate a registered card or the Master Card to the reader You can use the keypad to specify the delayed start time for the Secure mode Refer to the delayed start time in Secure mode on page 28 Lf For effective security purposes you can set to activate the sensors via auxiliary input ports only in Secure mode Duress Alarm If you are forced to open the door under a robber s control enter the Duress password and press with the number of your registered card or PIN See page 24 How to use the chime bell When you have connected and set the chime bell press So to ring the chime bell See page 34 English _ 15 intalization WIEGAND OUTPUT SETUP You can transfer data of the card read by SSA S2000 in the 26 bit Wiegand output format Enabling this function will disable the TTL output and the chime bell sound 1 To enable the 26 bit Wiegand output you must manipulate the switch panel SW1 and SW2 on the rear of the product 2 See the table below to make adjustment as needed Changing Output SW1 1 SW1 2 SW2 1 SW2 2 Orange line with white stripes Brown line with white stripes
36. normal and Secure modes in case of an input through the auxiliary port select the B BG gt buttons and press 4 Enter the two digit door relay output time and press 5 Enter the two digit alarm relay output time and press i 6 Enter the two digit TTL relay output time and press e You can specify a two digit time from 00 to 99 seconds e By default all output times are set to 00 Other output ports that are not specified for the output mode will not be activated For instance if you set the output mode to 5 2 and assign the operation time for each output device by following the steps 4 5 and 6 above only the alarm relay will operate English _ 31 O time setuo TO SPECIFY THE ALARM OPERATION TIME FOR AUX 2 1 Present the Master Card to the device samsune 2 Press Button B and Button B in sequence and press z 3 Refer to the output port table on page 29 and specify a desired output mode f you want the alarm relay alone to operate in normal and Secure modes in case of an input through the auxiliary port select the B B gt buttons and press 4 Enter the two digit door relay output time and press 5 Enter the two digit alarm relay output time and press 6 Enter the two digit TTL relay output time and press z e You can specify a two digit time from 00 to 99 seconds e By default all output times are set to 00 Other output ports that are not
37. ode is specified only the green LED indicator flashes FN 2 Press Button 7 and Button in sequence and press i When the device enters Standby only the red LED indicator flashes 3 Present a card or PIN number to delete Repeat this step if you want to register multiple cards or PIN numbers 4 Present the Master card to the device again and the device will switch to normal mode If no input is made for 20 seconds the device will switch to normal mode English _ 23 LNAWASVNVW Y3SN basic setup DURESS ALARM If you are forced to open the door under the control of a criminal such as a robber enter the predefined password with the number of your registered card or PIN which outputs the emergency TTL signal 1 Present the Master Card to the device samsune 2 Press Button B and Button 9 in sequence and press i 3 Enter the two digit Duress code and press e The default code is set to 00 However the number 77 can not be used because it is set for the Secure mode 7 BoP 5 TO SPECIFY THE RETRY COUNT FOR AN UNREGISTERED ID You can specify the retry count for authentication with an unregistered card or PIN If the retry count exceeds the set limit the keypad input will be suspended for the next one minute You can specify the keypad input suspension time in To specify the keypad input suspension time if the retry count with an unregistered ID exceeds the limit on page 25
38. pecify the alarm output for an input error of the Door contact Sensor See page 31 1 Present the Master Card to the device san 2 Press Button 8 and Button oO in sequence and press i TO CHECK THE OUTPUT SPECIFIED FOR AUX 1 You can check the output setting that you specified in To specify the alarm operation time for AUX 1 See page 31 1 Present the Master Card to the device 2 Press Button B and Button 3J in sequence and press 40_ Additional Features TO CHECK THE OUTPUT SPECIFIED FOR AUX 2 You can check the output setting that you specified in To specify the alarm operation time for AUX 2 See page 32 1 Present the Master Card to the device 2 Press Button B and Button B in sequence and press B S3YNLVss TVNOILIGGV TO CHECK THE OUTPUT SPECIFIED FOR AUX 3 You can check the output setting that you specified in To specify the alarm operation time for AUX 3 See page 32 1 Present the Master Card to the device jamais 2 Press Button B and Button 7 in sequence and press English _ 41 other information INITIAL VALUES This product operates in the following initial values For changing the settings or registering deleting the user card refer to the applicable section in this document 1 Entry permitted for a registered card The door control relay operates for 3 seconds The green LED indicator flashes for 3 seconds 2 Entr
39. port and operation time if an error occurs from the Door Contact Sensor You must have specified the operation time of the Door Contact Sensor Refer to To specify the operation time of the Door Contact Sensor on page 26 1 Present the Master Card to the device 2 Press Button B and Button in sequence and press 3 Refer to the output port table on page 29 and specify a desired output mode dNLaAs AWIL O I e If you want the alarm relay alone to operate in normal and Secure modes in case of an error from the Door contact Sensor select the B B gt buttons and press R 4 Enter the two digit door relay output time and press 5 Enter the two digit alarm relay output time and press p g 6 Enter the two digit TTL relay output time and press i e You can specify a two digit time from 00 to 99 seconds e By default all output times are set to 00 Lf Other output ports that are not specified for the output mode will not be activated For instance if you set the output mode to 5 2 and assign the operation time for each output device by following the steps 4 5 and 6 above only the alarm relay will operate TO SPECIFY THE ALARM OPERATION TIME FOR AUX 1 1 Present the Master Card to the device 2 Press Button B and Button B in sequence and press i 3 Refer to the output port table on page 29 and specify a desired output mode f you want the alarm relay alone to operate in
40. power to the product and short circuit the jumper for hated one second as shown l 3 When the initialization is completed 3 LED indicators are blinking 4 Turn off the product and restore it to the original installation state English _ 17 reader mode setup You can specify the operation mode for the device Once a mode is specified it will not switch until you perform the initialization You must keep the Master Card in safe for later use as it is required for your change to the device settings If progression is halted for more than one minute during any of the following processes the operation mode of the reader will return to the previous state READER MODE SETUP RF ONLY No Master Card or Master PIN is ever registered If you remember the Master Card or the Master PIN was registered initialize the product and try again 1 When you turn on the product all of the 3 LED indicators will flash with a beep No flashing of the 3 indicators denotes that the reader mode is already I ree specified TER res 2 Press Button 0 and Button 7 in sequence and press EE When the mode is specified only the green LED indicator flashes 3 Present a card that you want to register as the Master Card to the device When the Master Card is registered only the red LED indicator flashes 4 Present cards to register with the device one after another and the device will register them with
41. se if AUX 2 switches from H to L 36 65 Sense if AUX 3 switches from L to H 37 66 Sense if AUX 3 switches from H to L 38 67 Sense if the Exit button switches from L to H 39 68 Sense if the Exit button switches from H to L 40 69 Sense if the Door Contact Sensor switches from L to H 41 70 Sense if the Door Contact Sensor switches from H to L 42 71 Set the TTL output to H 43 72 Set the TTL output to L 44 if Keypad input enabled 45 74 Keypad input disabled 46 77 Chime bell enabled 47 78 Chime bell disabled 48 80 Set the starting delay time for Patrol Mode 49 81 Set the operation time for the Door Contact Sensor 50 82 To specify the retry count for an unregistered ID 51 83 Set the limitation time for the keypad input 52 84 Set the alarm output port for the dismantled device ex 88 Dismantled device alarm enabled 04 89 Dismantled device alarm disabled 99 System Initialization all settings deleted 44_ Other Information troubleshooting TROUBLESHOOTING If the product does not work properly please check the followings before contacting us If the trouble persists please contact the SAMSUNG Customer Service near you Problem When turn on the product it does not Check if the product is installed properly and works normally recognize the card with just the 3 LED indicators blinking 1 Action In the initial setup of the product or after it is initialized Set the operation mode and register the Master
42. specified for the output mode will not be activated For instance if you set the output mode to 5 2 and assign the operation time for each output device by following the steps 4 5 and 6 above only the alarm relay will operate TO SPECIFY THE ALARM OPERATION TIME FOR AUX 3 1 Present the Master Card to the device samen 2 Press Button B and Button in sequence and press 3 Refer to the output port table on page 29 and specify a desired output mode f you want the alarm relay alone to operate in normal and Secure modes in case of an input through the auxiliary port select the B B buttons and press 4 Enter the two digit door relay output time and press z 5 Enter the two digit alarm relay output time and press i 6 Enter the two digit TTL relay output time and press P e You can specify a two digit time from 00 to 99 seconds e By default all output times are set to 00 LY Other output ports that are not specified for the output mode will not be activated For instance if you set the output mode to 5 2 and assign the operation time for each output device by following the steps 4 5 and 6 above only the alarm relay will operate 32_ I O Time Setup TO ACTIVATE OR DEACTIVATE THE DOOR RELAY BY THE DOOR CONTACT SENSOR You can set the Door Contact Sensor to control the door lock This is to allow the Door Contact Sensor to control the door relay where the sensor keeps the door relay acti
43. ticated 8 24 Set the Door Contact Sensor alarming time 9 25 Set the AUX 1 alarming time 10 26 Set the AUX 2 alarming time 11 27 Set the AUX 3 alarming time 12 29 Set the Duress Mode password 2 digits 13 30 Set the TTL output time in Duress Mode 14 31 0 check the output of the registered card user test on code 21 15 32 0 check the output of the unregistered card user 16 34 0 check the output specified for the Door Contact Sensor alarm 17 35 0 check the output specified for AUX 1 18 36 0 check the output specified for AUX 2 19 on 0 check the output specified for AUX 3 20 39 Set the chime bell ringing time 21 41 Set the door open 22 42 Release the door opening 23 43 Set the QUICK Mode 24 44 Release the QUICK Mode 25 45 Toggle to control the door relay 26 46 Release the toggling to control the door relay 27 47 Set to control the door relay using the Door Contact Sensor 28 48 Release the control of the door relay using the Door Contact Sensor English _ 43 other information NO Code Number Function Item 29 51 Turn off the sound 30 52 Turn on the sound 31 60 To specify the keypad input suspension time if the retry count with an unregistered ID exceeds the limit 32 61 Sense if AUX 1 switches from L to H 33 62 Sense if AUX 1 switches from H to L 34 63 Sense if AUX 2 switches from L to H 35 64 Sen
44. utput specified for the Door Contact Sensor alarm To check the output specified for AUX 1 To check the output specified for AUX 2 To check the output specified for AUX 3 InItlal Values Functlon codes Troubleshooting product specifications English _ 5 oroduct introduction FEATURES This controller is best designed for a single entry door control single door access control It can store up to 512 cards including the Master Card that enables you to register delete or set various user cards to your preference This product features 5 external ports that can be connected to the Exit button Door Contact Sensor Motion Sensor and Fire Sensor It also has 2 relay outputs that can control the door lock and alarm relay The dual tamper switch triggers an alert if the product is forcibly disassembled You can use the keypad to configure all settings as necessary This product is designed for a standalone system Single Door Access Control You can use the RF card SSA C100 SSA C110 SSA C120 to control a single door User Registration You can register a total of 512 cards including the Master Card Keypad Registration SSA S2000 is equipped with the built in keypad that you can use to register delete cards or configure various settings independently Buzzer On Off With the help of various buzzer tones you can check the operation status and the current settings and results of the product Extern
45. ve from the normal opening of the door to its closing This is useful when the door stays open with just one authentication 1 Present the Master Card to the device 2 Press Button oO and Button g in sequence and press To release the control by the Door contact Sensor repeat Step 1 above select the B p buttons and press a Mlle ee ee Lf The default is set to disabled ED er English _ 33 dNLas AWIL O I advanced setting TO SPECIFY THE TTL OUTPUT OPERATION MODE This is to switch the TTL output from LOW OV to HIGH 5V when it is activated 1 Present the Master Card to the device Samsun 2 Press Button and Button in sequence and press To release the setting repeat Step 1 above select the B B gt buttons and press o i samsuno ee ee Lf The default is set to switch from HIGH 5V to LOW 0V we TO SET THE CHIME BELL FUNCTION You can specify the use of the chime bell Use the chime bell in the TTL level 5V for this purpose The default output time is 5 seconds For changing the output time refer to To specify the chime bell operation time on page 35 SAMSUNG 1 Present the Master Card to the device 2 Press Button twice and press i e twice and press lt B buttons and press ee 5r L The default is set to use the chime bell ee 34_ Advanced Setting TO SPECIFY THE CHIME BELL OPERATI
46. vice will switch to normal mode If no input is made for 20 seconds the device will switch to normal mode 5 ee 7 amp REGISTERING CARDS IN A COMBINATION OF RF AND P W MODES Ensure that you must have registered the Master Card and the device is specified in RF P W mode 1 Present the Master Card to the device When the mode is specified only the green LED indicator flashes 2 Press Button rm and Button B in sequence and press E When the device enters Standby only the red LED indicator flashes 3 Present a card to the device enter the 4 6 digit password and press f Repeat this step if you want to register multiple cards 4 Present the Master card to the device again and the device will switch to normal mode If no input is made for 20 seconds the device will switch to normal mode English _ 21 LNAWSSVNVW Y3SN user management TO REGISTER CARDS IN PIN MODE Ensure that you must have registered the Master Card and the device is specified in PIN mode 1 Enter the Master PIN number and press When the mode is specified only the green LED indicator flashes wel 2 Press Button i and Button B in sequence and press When the mode is specified only the green LED indicator flashes 3 If you enter a user number 4 6 digits to register and press the PIN number will be registered with a beep Repeat this step if you want to register multiple PIN numbers
47. xternal reader and SSA S2000 for any disconnection or short circuit Check if there occurs a noise on the connection cable between the external reader and SSA 2000 If you have to use a measuring device such as an oscilloscope or a multimeter please consult with a qualified technician Measure the Wiegand communication cable and check if the exit reader works property Check the Wiegand output state of the external reader by referring to the user manual and replace the reader if it shows an abnormal output If there occurs a noise on the Wiegand communication cable using the measuring device Reinforce the GND line by using the shield line and space line as additional GND points Extend the Wiegand communication range along with the stable signal reception using the repeater For more information refer to the external reader connection section in the user manual If the problem persists after you have followed the procedures above contact a designated service center The door lock does not operate at all Check if the door lock is connected to SSA S2000 properly The connection method may differ depending on the type and operation mode NO NC of the door lock Check the status of the door lock Check the connection cable between the door lock and SSA S2000 for any disconnection or short circuit Check if the door lock works normally If you have to use a measuring device such as an oscilloscop
48. y denied for an unregistered card The alarm relay operates for 2 seconds The red LED indicator flashes for 2 seconds 3 Duress Mode Password 00 The TTL output port produces a signal for 3 seconds in Duress mode 4 QUICK MODE Disabled 5 Chime Bell Output Enabled Chime Bell Operating Time 0 5 second 6 Melody Sound Enabled 7 Keypad Input Limited Use 20 seconds 8 When an input signal is sensed H gt L Common for all inputs 9 When a TTL output signal is sensed H gt L 10 Patrol Mode Delay Time 00 minute 11 Door Sensor Sensing Time 00 second 12 Retry count for an unauthenticated entry 05 times 13 Alarm for Dismantled Device Disabled Dismantled device Alarm Output Port 02 Alarm Relay 14 Toggle Mode Disabled 15 Control Lock by the Door Sensor Disabled 42_ Additional Features FUNCTION CODES S3YNLVas TVNOILIGGV NO Code Number Function Item 1 11 Additional user card registration RF CARD ONLY MODE 2 12 Additional user card and PIN registration RF CARD PIN MODE 3 13 Additional PIN registration PIN ONLY MODE 4 14 Delete a registered card or PIN number 5 i5 Additional user card or PIN registration RF PIN combination mode 6 21 To specify the output time if the card is authenticated T 22 To specify the output time if the card is not authen
49. y the delayed start time in Secure mode To specify the operation time of the Door Contact Sensor To specify the limited time for the keypad input To specify the alarm output port for the dismantled device To open or close the entry door To set or release the QUICK mode To set or release the Toggle mode for the door relay To specify the output time if the card is authenticated I O TIME SETUP ADVANCED SETTING ADDITIONAL FEATURES OTHER INFORMATION TROUBLESHOOTING PRODUCT SPECIFICATIONS 39 39 40 40 41 42 45 50 To specify the output time if the card is not authenticated To specify the Duress TTL output To specify the alarm output for an input error of the Door contact Sensor To specify the alarm operation time for AUX 1 To specify the alarm operation time for AUX 2 To specify the alarm operation time for AUX 3 To activate or deactivate the door relay by the Door Contact Sensor SLNALNOO To specify the TTL output operation mode To set the chime bell function To specify the chime bell operation time To specify the input mode for AUX 1 To specify the input mode for AUX 2 To specify the input mode for AUX 3 To specify the input mode for the Exit Button To specify the input mode for the Door Contact Sensor Mute To specify the use of the tamper alarm To check the output specified for a registered card user To check the output specified for an unregistered card user To check the o
Download Pdf Manuals
Related Search