Samsung BN68-02611A-04 User's Manual
Contents
1. Authentication Mode OPEN SHARED WPAPSK WPA2PSK Encryption Type WEP TKIP AES Configuring the Network Connection Wireless The instructions below are for networks that use the Dynamic Host Configuration Protocol DHCP to configure network connections automatically If your have a Static IP network see your user s manual for configuration instructions To configure your network connection for a network that uses DHCP follow these steps 1 Connect your TV to your network as shown in the illustrations above Network Setup Not Selected Internet Protocol Setup Auto Select a network 2 Turn on your TV press the MENU button on your remote and the select Setup Network 3 Set the Network Type to Wireless if it is not already set to Wireless 4 Select Network Setup The Network Setup screen appears Move Enter Return 5 Onthe Network Setup menu select an AP Access Point and ad hoc network if you have selected network with a security key the Security Key screen appears 6 Enter the s using the numbers on the remote and then press the Blue button on your remote amp If your network uses WEP security encryption 0 9 and A F will be available on the Security Key screen Use the Direction button on your remote to move to the characters and the enter key to select them 7 Onthe Network Setup menu set Internet Protocol Setup and DNS to Auto The Auto acquires and enters the necessary in2. navigate while Plug amp Play is running press the Up Down Left or Right arrow buttons on your remote To make a selection press the ENTERL button To skip a screen press the MENU button To turn on your TV press the POWER button on the remote or press the POWER button on the TV To run Plug amp Play follow these steps Plug amp Play Select Language of the OSD Language Move L Enter 1 On the Language screen select the language for the On Screen Display OSD using your remote control and then press ENTERC button The Home Use screen appears 2 Select Home Use and then press ENTER button If you select Store Demo the TV will reset your picture and audio settings every 30 minutes After you press ENTER button the Antenna Source screen appears 3 If your TV is only attached to an antenna select Air If your TV is only attached to cable and you have no cable box select Cable If your TV is attached to an antenna and cable with no box select Auto When done press ENTERL button on your remote The Select Cable System screen appears IMPORTANT If your TV is attached to a cable or satellite box skip Steps 3 through 5 After Plug amp Play is complete set your TV to Channel 3 or 4 according to the directions for your cable or satellite box If your TV is attached to a cable system and you have no cable box you must select your cable system type If you have Digital cable you must select the cab
3. Quick Setup Guide Congratulations on the purchase of your new Samsung TV Read this setup guide to get your TV up and running quickly 1 800 SAMSUNG 1 800 726 7864 Samsung Electronics America Inc 85 Challenger Road Ridgefield Park NJ 07660 2112 Samsung Electronics Canada Inc 55 Standish Court Mississauga Ontario L5R 4B2 Call Center hours of operation Mon Sun 9 00 AM 12 AM EST To register this product visit www samsung convregister Getting Started Step 1 Install the Stand Follow the steps below to connect the TV to the stand SILO Please do not retum this unit If you have problems operating your TV call 1 800 SAMSUNG 1 800 726 7864 For web support please visit ww samsung com support amp Make sure to distinguish between the front and back of the Stand and Guide Stand when assembling them amp Make sure that at least two people lift and move the LCD TV amp Stand the product up and fasten the screws If you fasten the screws with the LCD TV placed down it may lean to one side Guide Stand Step 2 Install the Batteries into the Remote To install batteries into your remote control follow these steps 1 Lift the cover on the back of the remote upward as shown in the figure to the right 2 Install two AAA batteries amp Make sure to match the and ends of the batteries to the diagram in the battery compartm
4. SESSE ET ESEEE EEE DEES ES EESER SEES ESSE EE EED PRC R OOOH E RSET OH SCEEEE HEHE EEEEOEE TEESE TE EOEEE EEE EESOH EOL ESEES EH EETOEHSOEEEEE HE EEETEEEHESSEEH ED SESHDELELEOEE EE ESEES ER SENSEH EEL EE SOREL EES amp This is a special remote control for the visually impaired persons and has Braille points on the Power Channel Volume buttons POWER O Turns the TV on and off Press to switch between the sources Blu ray player cable box DVD player etc connected to your TV Press number buttons for direct access to channels Press to select additional digital channels broadcast by the same station For example to select channel 54 3 press 54 press and then press 3 Adjusts the volume Displays the channel list on the screen View the Media Play Quickly selects frequently used functions Selects the on screen menu items and changes the values seen on the menu Return to the previous menu Colored buttons for use in the Channel List Media Play menu etc Use these buttons in the Media Play and Anynet modes D o PMODE ON Turns the remote control light on and off When on the buttons become illuminated for a moment when pressed Using the remote control with this button set to off will reduce the battery usage time SOURCE Return to the previous channel Aa Cut off the sound temporarily SA Change channels amp If your TV is attached to a cable or satellite box you c
5. annel in your area Select Manual if you don t or if you have a cable or satellite box When done press ENTER button The Daylight Savings screen appears amp If you select Manual the clock setting screen appears 7 Select the Daylight Saving Time setting Off On or Auto and then press ENTERC button 8 After the time zone screen The connection method for best HD screen quality is displayed Press Right arrow button on your remote to view each screen in succession Press the BLUE button to skip this section 9 The Enjoy your TV screen appears and then press ENTER button Basic Functions Changing the Screen Size ssn Your TV has several screen size options each designed to work best with specific types of video input If you have a cable box or satellite receiver it may have its own set of screen sizes as well To change the screen size press the P SIZE button on your remote The first time you press it your TV displays the current setting Thereafter each time you press the P SIZE button you change the size of the picture on the screen English 1 Connect your TV to your Home Theater or other audio device to enjoy enhanced sound quality Connecting an audio device POPPE SORE EEE EEEOH SE EOEE SEETHER EOE T OEE T ETOH OEEEEEEETEHE EH SET EET OTOH SEEOEHOTEEESEHSEHOOEESEOE LESSEE SESEH EEE OEHELELET EL EESOE EE ES EET ELSE HELEOEE EELS Using an Audio Cable Device i 5 Amplifier DVD Hom
6. ct your TV to your network using cable depending on your network setup They are illustrated below External Modem ADSL VDSL Cable TV The Modem Port on the Wall TV Rear Panel Modem Cable LAN Cable TV Rear Panel aja The LAN Port on the Wall LAN Cable Configuring the Network Connection Wired sescocooocoooooccoscocoososoooooocoosooocoscoocosoooocoococcoooooocooccosoooooocoooooocoocoocoosoooooocoosoooooscoocoocoosooocooooooooosoooo Most home networks use the Dynamic Host Configuration Protocol DHCP to configure network connections Home networks that support DHCP automatically provide the IP address subnet mask gateway and DNS values your TV needs to access the Internet so you don t have to enter them manually To configure your network connection for a network that uses DHCP follow these steps 1 Connect your TV to your network as shown in one of the illustrations above 2 Turn on your TV press the MENU button on your remote and then select Setup Network 3 Set the Network Type to Wired if it is not already set to Wired 4 Select Network Setup The Network Setup screen appears Network Setup Internet Protocol Setup Auto Ca Enter gt Return Move 5 On the Network Setup menu set Internet Protocol Setup and DNS to Auto Auto acquires and enters the necessary internet values automatically 6 Select Network Test to check Internet connectivity amp Some networks ar
7. e Static IP networks If your network is a Static IP network you can not use DHCP to configure the network connection Instead you must enter the IP Address Subnet Mask Gateway and DNS Server manually For instructions explaining how to configure a Static IP network see your user s manual English 2 Network Connection Wireless You can connect your TV to your LAN through a standard wireless router or modem To connect wirelessly you must first attach a Samsung Wireless LAN Adapter WISOSABGN WISOSABGN2 WIS1OABGN sold separately to either the USB1 HDD or USB2 port on the back of your TV See the illustration below Wireless IP sharer AP having DHCP Server 5 TV Side Panel TV Rear Panel The LAN Port on the Wall Samsung Wireless LAN Adapter Samsung Wireless LAN Cable LAN Adapter Samsung s Wireless LAN adapter supports the IEEE 802 11A IEEE 802 11B IEEE 802 11G and IEEE 802 11N wireless communication protocols For your TV to connect to your network the wireless router or modem you use must also support one of these protocols The fastest of these protocols is IEEE 802 11N Most wireless network systems incorporate a security system that requires devices that access the network through an access point or AP typically a wireless modem or router to transmit an encrypted security code called an access key For regular connections your TV is compatible with the following security protocols
8. e Theater connection Using an Optical Cable Digital Audio System OPTICAL Using an HDMI Cable o c Using an D Sub Cable AUDIO QUT The following sizes are available Wide Fit 4 3 Standard screen Screen Fit amp Screen Fit displays a full HD picture covering the entire screen with no cutoff on any side It is only available when your TV inputs an HDMI 720p 1080i 1080p Component 1080 1080p or DTV over the air 1080i signal Changing the Picture Mode Your TV has four preset Picture Modes with factory adjusted settings each designed to give you an excellent picture under specific conditions The Picture Modes are listed and described in the table below iode Brightens picture For a vibrant enhanced image in brightly lit or For a comfortable easy on the eyes picture in a normally lit room For a studio quality cinema picture in a dimly lit or dark room To change the Picture Mode follow these steps Standard Fora bright detailed picture in a normally lit room 1 Turn on your TV 2 Using your remote press the MENU button on your remote Then select Picture Mode 3 On the Picture Mode menu use the lt or gt on your remote to select the Picture Mode you want 4 Press the EXIT button to exit the menu Remote Control Buttons and Functions PCCP COELHO ESE EEEEEEH EL EEEESE HOLES EE TEE SETOEESEEEEE TOE ESEE OEE SETSEHEEESEEE EE EHEEOEEEEESEH OEE
9. en appears Clock Set 4 gt Move Adjust C Enter Return 5 Using the number buttons on your remote enter the Month Day Year Hour and Minute Use the lt or gt button to move between entry fields 6 Press the RETURN button on your remote when done Connecting a USB Device for Media Play POC POOE HSER SEEEEEETEESEESEEEEEEOE ETE EOEEO EEE OEETE ETE ESESOOEETEESEESEEEOEEOE ET ETOHSE HE SEEES EHTEL ETES EO ELENSEHE REE SESE ELLOS SHEE ELSE HSER EEE You can enjoy photo music and movie files stored on a USB device by connecting it to the TV and using the Media Play feature To connect a USB device for Media Play follow these steps USB Drive 1 Turn on your TV 2 Connect a USB device containing photo music and or movie files to the USB1 HDD or USB2 jack on the side of the TV 3 When the Application selection screen appears press the ENTERL button on your remote to select Media Play USB Media Videos A gt E SUM IA Change Device D View Devices C8 Enter Return Connecting to a Local Area Network To enjoy watching streaming content from online providers such as You Tube and Blockbuster you must follow the steps below to connect the TV to your network Network Connection Wired COOP CEE OHHE SE SEHO HEE EEHEH EEO EEEOS OE SESOEH ETE OEOOT OSE OTOOH EE SOEEE TOE EOSEOT ET OOEEO TET ESEOEE ET OOOSOTESETOTEEESETHTE TE SESOS ET ESESESEEEEEOEEE There are two main ways to conne
10. ent 3 Replace the cover Step 3 Connect Power and Antenna or Cable Connect ANT IN to e Wall cable jack or e VHF UHF Antenna or e Cable or Satellite box Ant or Cable Use a 75 ohm round cable Out Power Input Make sure the AC power cord is plugged in securely to the wall outlet and the TV Step 4 Connect External Devices Connecting an AV device Blu ray player cable satellite box etc POPC O OEE T EE EEHTEEEHEHEESEEHEEOESOSOH EET OSEEE TO EOEETEETEOH EES ESEHE TE SEOE ETE E SOOTHE TOSETOTEEETESTETEHEHETOEETES OE EEHSHTESESEEEHSEEEEEEEEEEEE For the very best picture quality select HD signal sources and use HDMI cables and connections Note that many digital cable programs are not in HD Check with your video provider to ensure your are receiving HD signals S QERHREBHBR HB HRBHEHRHRHEHRHRHEE YNI INGH KEN ANIAN olanv nection 480i only Using an Audio Video Cable VCR DVD Blu ray player Cable Box Satellite receiver VCR video cable yellow Lowest Quality Connection Step S Run Plug amp Play When you turn on your TV for the first time it automatically launches the Plug amp Play function With Plug amp Play you can select the On Screen Display language set the clock mode and launch the TV s channel memorizing process It also displays connection instructions similar to those in this guide To
11. hange the channel using the box s remote Displays the main on screen menu Displays Favorite Channel Lists on the screen Press to display information on the TV screen Exit the menu S MODE Selects the sound mode SLEEP Setting the Sleep Timer MTS Press to choose stereo mono or Separate Audio Program SAP broadcast P SIZE Le Controls recording on Samsung recorders with the Anynet feature Selecting a Source To watch a movie on your Blu ray player or watch your favorite TV show you must select the correct source A source is a device such as a Blu ray DVD player a cable satellite box antenna or a SOURCE cable TV input Sources can be connected to your TV through the HDMI DVI Component Composite or D sub connections or through the Antenna or Cable In connections To view the signal from a source connected to the HDMI DVI Component Composite or D sub jack press the SOURCE button on your remote Each time you press the SOURCE button you change to a different source Viewing the On Screen Menus PCC OOHO SEO EE SHEET EE SOOT EOE E HOES EEO SOHOO SEO TOEEO EEO EOOE SHOOT OT SEES ESOT E TEESE EC OTOSO EE OETOOETEOEHEHT EE OEHS OEE ESHSEETE ES ONSELEEEEEEEEOOS To view the On Screen Menus follow these steps 1 With the power on press the MENU button on your remote The main menu appears The menu s left side has the following menu options Picture Sound Channel Setup Inp
12. le system type for both Analog and Digital COCO S CEES EEEEHETOEESOTS OLEH OEEHETHTOSEEETEEEEOSHEETOSHESTSETEOEEETEOOEE TE EEEEEETETEE HE EOEESETEEETETEEESEDEEEEEESOE amp When connecting to AV IN 1 on the back of your TY attach the video cable yellow to the green jack next to the AV IN 1 label The jack will not match the color of the i up to 1080p Using an HDMI Cable HDMI OUT Device _ E g n n DVD Blu Ray player HD Cable Box HD Satellite receiver STB The HDMI connection carries digital video and audio Best Connection 1 up to 1080p Using an DVI to HDMI Cable Device 0 0 0 6 DVD Blu Ray player Cable Box Satellite receiver STB AUDIO OUT OUT Very Good Connection ction up to 1080p Using a Component Cable AUDIO OUT COMPONENT OUT Device 0 0 00 VCR DVD Blu ray player Cable Box Satellite receiver Tit mL ER I Good Connection After you have selected the cable system type select Start and then press the ENTERL4 button on your remote amp Most cable systems are Standard STD systems If you are not sure about what kind of cable system you have contact your cable company 5 The TV memorizes the available channels This process can take up to 45 minutes After the TV has memorized the channels the Clock Mode screen appears 6 Choose the Clock Mode Select Auto if you have a digital ch
13. ternet values automatically 8 Select Network Test to check internet connectivity amp For more information see your user s manual BN68 02611A 04
14. ut Application and Support MEDIAP TOOLS 2 Pressthe A or W button on your remote to select a menu option and then press the ENTERL button 3 When done using the menu press the EXIT button on your remote to exit P MODE Selects picture mode P SIZE Choose the picture size CC Controls the caption decoder POCO OOOOH O CE HEEHTO EH OOHEE ESO OTOH OEE OOOO S OOH OEO OEE ESOS O OSE OTOOHEEESOOTHEO COS ETOSH ESO OTHEO EET ESOTOEEOOHEEHTEESHOHOEEEEDEEETEEDEOSEOE You can change the channel and adjust the volume by using the CH and VOL buttons on the remote You can also change the channels by pressing the V CH A buttons on the front panel of your TV and adjust the bee volume by pressing the VOL buttons Remote control sensor Power Indicator Setting the Clock POCO COOH EEE EOHOHE EEE EEHOE OSE O TOOT EEE OTOH TOOT OOOO EOE THOEE TEES OOO OEE SETHE EOS ETOEEETOHHHEEEEOEOOT EEE ETHOS OE EES OODELEEEOSEESEEEEOEDELE Before you can use your TV s On Off Timer you must set the clock To set the clock follow these steps 1 Turn on your TV 2 Using your remote press the MENU button on your remote Then select Setup Time 3 Select Clock Mode and then press the ENTERL4 button Set Clock Mode to Manual amp Select Auto if you have a digital channel in your area and are not using a cable sat box 4 Select Clock Set and then press the ENTERL button The Clock Set scre
Download Pdf Manuals
Related Search