Rowenta NOMAD HC080 User's Manual
Contents
1. to obtain a perfect transition between the zone on the top of the head and the sides Shown atA on Fig 23 tilt the comb slightly and cut the hair that sticks out Fig 27 2nd STAGE OUTLINING e See the paragraph on Outlining in the Crew cut section 14 TECHNIQUE FORTRIMMING ANDTIDYING UP gt lt This is how to trim a haircut that is starting to get untidy particularly on the neckline the sideburns and around the ears THE CUT For this technique use the clipper without the comb attachment a Around the ears Fig 28 and 29 Comb the hair into the desired style GB Place the upside down clipper between the sideburns and the ear making sure that the corner of the blade is on the hairline use only the edge of the clipper Move the clipper slowly above around and behind the ears b The neckline Fig 30 e For the neckline hold the upside down clipper lightly against the hair e Operate as shown on the drawing with small downward strokes c The sidebums Fig 31 Hold the clipper upside down with the cutting edge perpendicular to the head and work downwards Use small strokes 15 TECHNIQUE FOR A SHORT BACK AND SIDES With this technique you clip only the sides and neck and keep the hair long on top The cutting settings to use 3 to 21 mm in function of the desired length Fig 32 1st STAGE THE CUT e Clip the hair on the neck and the sides using the technique described in the Crew cut2. section up to the point A Fig 32 using the clipper fitted with the adjustable comb attachment 3 to 21 mm in function of the desired length e Above the point A situated a few cm above the ears use a barber s comb to obtain a perfectly tidy transition Hold the comb at an angle to the head Fig 33 and cut any hair sticking out from the comb using the clipper without the adjustable comb attachment Use the barber s comb to guide the clipper Fig 34 e Do not clip the hair on top of the head 2nd STAGE OUTLINING e See the paragraph on Outlining in the Crew cut section WIRING INSTRUCTIONS FOR U K ONLY SAFETY NOTES FOR REWIREABLE OR MOULDED PLUG The mains lead of this appliance may be already fitted with a BS 1363 13 A plug Should the fuse need to be replaced a 13 A ASTA approved BS 1362 fuse must be used If your socket outlet is not suitable for the plug then the plug must be removed cut off if it is a moulded on plug and an appropriate one fitted Warning dispose of a plug that has been cut from the power supply cord as such a plug is hazardous if inserted in a live 13 A socket outlet elsewhere in the house Always replace the fuse cover after fitting a fuse The plug must NOT be used if the cover is omitted or lost until a replacement is obtained make certain that only the correct fuse cover is used and fitted For plugs with a detachable fuse cover the replacement must be the same as the colour insert in th
3. QROWenTea 030052 17 03 HCO80 NOMAD Gebrauchsanweisung Instructions for use Gebruiksaanwijzing Instruzioni per l uso Modo de empleo Instru es de utiliza o K ytt ohje N vod k pou it Instrukcja obs ugi Haszn lati utas t sok N vod na pou itie Uputa o kori tenju Navodilo za uporabo Uputstvo o kori enju VHCTpyKuna no NCNOSIB30BAHNIO Odnyleg xp oews Kullanma talimat Jais YI Ju doigts fingers le A ie 9 12 21 mm E 3 6 mm The quality of the product and its precisely adjusted cutting lengths make it a professional grade tool You have chosen this clipper with a view to cutting and tidying hair easily and conveniently GB Please read the instructions before using the appliance to avoid any risk arising from improper use L DESCRIPTION OF THE CLIPPER AND ITS ACCESSORIES A Onloff button B Adjustable comb attachment C Cutting length adjustment button D Cutting length indicator 3 6 9 12 15 18 21 E Cutting head F Power on indicator G Adapter H Cleaning brush Y Lubricating oil y Barber s comb with certain models only K Pair of scissors with certain models only L Storage pouch with certain models only nstruction booklet 2 PREPARING FOR USE Voltage Your appliance has been designed to use 220 240V only e Check that this voltage matches the voltage of your electricity supply You have chosen a rechargeable appliance designed for use wit
4. ance is designed for use in the home only Do not use the clipper for more than k 10 minutes without a pause i Important the clipper and the adapter must not be immersed or held under running water Do not leave the appliance for long periods at temperatures below 0 C or above 40 C behind glass in full sunlight for example Do not expose the appliance to direct sunlight for long periods Do not use an extension lead in your bathroom e Keep the cord appliance and accessories away from any source of heat appliance could put your safety at risk When you are using the clipper keep it well away from eyelashes clothes and any other object to avoid any risk of injury or blockage e f the clipper is used by several people the cutting head should be cleaned appropriately e Close supervision is necessary when the appliance is used on or in the presence of children or disabled people e Never leave the clipper within the reach of children e Be careful when you are using the clipper for the first time Take your time Use slow controlled gestures e Do not use the clipper on animals Do not use the appliance on injured skin if you have dermatological problems eczema varicose veins skin inflammations moles acne warts birth marks etc e Special tools are required to dismantle this appliance Any maintenance work must be carried out by the manufacturer its after sales service or a person with similar qua
5. e base of the plug or as directly by the embossed wording on the base of the plug If the detachable fuse cover is lost a replacement may be purchased from an approved Rowenta Service Centre See enclosed Service Information leaflet Information for supply may also be obtained from the plug manufacturer U K ONLY FITTING A PLUG Important the wires in this lead are coloured in accordance with the following codes Blue Neutral Brown live Please read the instructions given below before connecting the cord to a plug If in doubt please consult a qualified electrician As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows ethe wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK Gg oros L ethe wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or sueo La Fit correct coloured RED N black Use cable Neither core is to be connected to the earth terminal of a three pin plug en This appliance requires a 13 fuse ASTA approved to BS 1362 SERVICE SPARE PARTS U K ONLY Rowenta U K Ltd has a network of Service Agents throughout the country To telephone your nearest Rowenta Service Centre see enclosed Service Information leaflet These Service Agents carry out in guarantee repairs free of charge and out of g
6. h mains power or in autonomous cordless mode A Mains operation Switch the On Off button to O Fig 2 Plug the connector into the appliance Fig 3 and the adapter into the mains socket Fig A Turn the appliance on Fig 5 E During use the appliance does not recharge B Cordless operation The appliance functions with its accumulators Before using it for the first ime charge the appliance with the adapter for 14 hours The next 3 times you use your clipper it is important to let it discharge completely The recommended charging time is 8 hours When the charging indicator is red your appliance is charging Once the transformer has been unplugged the appliance is ready for AD minutes of cordless operation IMPORTANT 1 To optimise the cutting power of your blades it is essential to oil them before each use See paragraph 7 2 To avoid damaging the accumulators Never charge them for longer than 20 hours ata time Only charge the accumulators when there is a noticeable drop in the appliance s performance or if the appliance has not been used for over 6 months 3 SAFETY PRECAUTIONS Unplug the appliance before removing the comb attachment lubricating the blades etc and after use Any error when connecting the appliance can cause irreparable harm not covered by the guarantee Do not use or recharge the clipper near baths basins showers or other recipients containing water pE Your appli
7. lifications to avoid all danger e Cutting and styling advice is offered purely as a guide and Rowenta can not be held responsible in the event that the results obtained do not fulfil the user s expectations e For any malfunctions see Troubleshooting or contact our Customer Helpdesk or your dealer 4 7 SETTING ADJ USTABLE COMB ATTACHMENT eYour clipper is fitted with a comb attachment that allows you to choose the cutting length To select one of the settings push the comb to align it with the desired setting Fig 6 The cutting length in mm is shown on the sides of the clipper Fig 7 3 6 9 12 15 18 or 21 mm These values are purely indicative the actual cutting length may vary according to the angle at which the clipper is held 5 USING THE CLIPPER WITHOUT THE COMB ATTACHMENT e For shaved head cuts or outlining you can remove the comb attachment by sliding it off as shown in fig 8 6 CLEANING The clipper requires very little cleaning You can clean it with a slightly damp cloth To clean the adjus table comb attachment remove it as shown in fig 8 and use the cleaning brush to remove any hair Fig 9 e After each use the cutting blades should be cleaned with the cleaning brush Fig 10 7 LUBRICATION To maintain the performance of your clipper it is essential to oil the cutting blades before each use with the lubricating oil provided or failing this with a sewing machine oil e Before lubricati
8. lipper always stays at an angle to the head To start with cut only a small amount of hair at a time until you are familiar with the length left by the comb s different settings To obtain an even cut never force the clipper to move too quickly through the hair by pushing it e Never stop moving the clipper in the middle of the hair e Start by using the comb s maximum setting i e the one that leaves the greatest length of hair before trying the others Sec easy requires some experience of clipping e difficult 11 TECHNIQUE FOR A CREW CUT lt BASIC TECHNIQUE With this technique the cut follows the shape of the head e Adjust the cutting setting in function of the desired hair length Fig 13 e Don t forget to adjust the comb s setting at the different stages of the cut 1st STAGE THE CUT a The neck e Comb the hair e Start by clipping the hair on the neck from the base up using the 21 mm setting e Hold the clipper firmly against the hair with the teeth of the comb pointed slightly upwards Fig 14 e Slowly move the clipper up and away from the hair cutting only a small amount of hair at a time When the hair on the neck is evenly cut to 21 mm change the setting to the desired length and repeat the first 3 steps Fig 15 e Stop clipping at regular intervals comb the hair and check the result obtained b Sides and top e Repeat the procedure to clip the sides e Change the comb se
9. ng the appliance unplug it and use the cleaning brush to remove any hair caught in the cutting blades Fig 10 e Lubricate the blades at the positions indicated Fig 11 a single drop at each position is sufficient e Operate the clipper for a few seconds Wipe off any excess oil with a cloth 8 ENVIRONMENTAL PROTECTION va Atthe end of your product s useful life please take it to a waste collection centre for recycling 9 TROUBLESHOOTING The clipper doesn t cut any more Have you lubricated the blades see paragraph 7 The clipper won t start in cordless operation or no longer has sufficient autonomy Have you recharged it e Never use the appliance if it is not working correctly or if it has fallen invisible damage to the GB 10 A FEWTIPS ON CLIPPING GB e Use the clipper on hair that is clean and dry e Dry your hair in the style you are aiming to achieve e Check that the clipper is correctly lubricated e Position the person whose hair you are going to cut in such a way that you can easily see the top of their head Fig 12 e Place a towel around their neck and on their shoulders e Before clipping use a comb to make sure that the hair is not tangled e Before you start clipping take note of the way the hair grows and any tufts the hollows and bumps on the head often situated at the base of the neck if you apply the clipper directly onto a bump it will leave a clear patch e Make sure the c
10. or 12 mm settings to keep a greater length Cut the hair from the front towards the back 2nd STAGE OUTLINING e See the paragraph on Outlining in the Crew cut section 13 TECHNIQUE FOR CUTTING OVERA STYLING COMB OR FINGERS flat top cut se s s This cut gives a flat surface on the top of the head e Adjust the cutting setting in function of the desired hair length Fig 23 e Don t forget to adjust the comb s setting at the different stages of the cut 1st STAGE THE CUT e For this type of cut the preliminary hairdrying is very important Fig 24 eWhen drying your hair work against the way the hair grows so that the hair stands upright e Start cutting on the sides and the neck using the cutting lengths indicated in fig 23 For the cutting technique see the Crew cut section To obtain perfectly flat hair on the top use a barber s comb or your fingers Fig 25 and 26 remove the comb attachment using a barber s comb or your fingers lift a small section of hair the hair should be held vertical move the comb or your fingers along the hair to the desired length use the clipper to cut the hair above the comb or your fingers using the latter as a guide the length of the last section of hair cut will guide you in cutting the rest of the hair continue the procedure section by section working from the crown of the head towards the front comb regularly to remove cut hair and check the result
11. ttings as you clip different zones see Fig 13 For the top use the same technique working from the forehead to the crown of the head and moving against the direction of hair growth Fig 16 Then even up the top and sides 2nd STAGE OUTLINING a The neck and the sidebums e Comb the hair e Remove the comb attachment eTrim around the hairline holding the clipper upside down and perpendicular to the head and moving downwards Use short strokes Fig 17 and 18 e Repeat the procedure for the sideburns Fig 19 b Around the ears e Carefully comb the hair around the ear Remove the comb attachment GB e Hold the clipper at an angle but use only one corner of the cutting unit slowly shaping the desired outline and following the direction of the cut Fig 20 Advice When you use the clipper without the comb attachment keep your movements light and steady When outlining keep the clipper perpendicular to the skin to avoid injury Fig 21 12 TECHNIQUE FOR AN AMERICAN STYLE CUT gt lt Very very short sides and neck and very short on top e Adjust the cutting setting in function of the desired hair length Fig 22 e Don t forget to adjust the comb s setting at the different stages of the cut Ist STAGE THE CUT eTo cut the hair on the sides and neck see the Crew cut section To finish the cut use the 3 mm setting to shave the head For the zone on top of the head see Fig 22 use the 9
12. uarantee repairs chargeable on behalf of Rowenta Should service be required or the appliance appear faulty consult your local Rowenta Service Agent in the first instance If a product develops a fault during the guarantee period it is the responsibility of the consumer to supply to the Service Agent proof of the date of purchase of the appliance eg Completed guarantee card and or receipt showing the date of pur chase
Download Pdf Manuals
Related Search