Renesas H8SX/1653 User's Manual
Contents
1. 2 Align the connectors on the board with those on the evaluation chip board according to their numbers figure 4 3 Adjust the height of the spacer of the evaluation chip board with the user system RENESAS Evaluation chip board Connector No Evaluation Board Chip Board oa Connector No Connector No dr UCN2 UCN2 Jl system interface board Figure 4 Connecting User System Interface Board to Evaluation Chip Board RENESAS 2 4 Recommended Dimensions for User System Mount Pad Footprint Figure 5 shows the recommended dimensions for the mount pad footprint for the user system with an IC socket for a TFP 120 package IC149 120 043 B51 manufactured by YAMAICHI ELECTRONICS Co Ltd Note that the dimensions in figure 5 are somewhat different from those of the actual chip s mount pad 17 10 min at LS 13 80 max gt 0 40 x 29 11 60 0 05 l 0 40 0 05 0 25 0 05 SS SS Sl w ol 2 H o H 3 8 1 op N x O s oO mm N I Unit mm Figure 5 Recommended Dimensions for Mount Pad RENESAS 2 5 Dimensions for Evaluation Chip Board and User System Interface Board The dimensions for the evaluation chip board and the user system interface board are shown in figure 6 140 0 100 0 Evaluation chip board 118 5 al ES 102 5 16 0 oO fon GO Te fap2. pe 78 5 User system interface board Unit mm Tolerance 0 5 mm Figure 6 Dimensions for Evaluation Chip Board and User System Interface Board 11 RENESAS 2 6 Resulting Dimensions after Connecting User System Interface Board The resulting dimensions after connecting the user system interface board to the user system are shown in figure 7 Evaluation chip board IC socket IC149 120 043 B51 manufactured by YAMAICHI ELECTRONICS Co Ltd User system pad Spacer 65 8 Unit mm Tolerance 41 0 mm Figure 7 Resulting Dimensions after Connecting User System Interface Board 12 RENESAS 2 7 Using the Emulator without Connecting User System WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected to or removed from any part Before connecting make sure that pin 1 on both sides are correctly aligned Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST CAUTION When this emulator is used without connecting to the user system ensure that the SW1 jumper pin is inserted to OFF Failure to do so will damage the emulator product user system interface cable and user system Attach the provided spacers 2 6MQ x 16 mm to four positions on the user system interface board not to apply loads
3. H8SX 1650 E6000H Emulator User s Manual HS1650EPH60HE 2 Verify the user system interface cable connections by checking the pin states with the CHECK command emulator command and checking the bus states with the FILL command emulator command If an error is detected recheck the soldered IC socket and the location of pin 1 3 The emulator connected to this user system interface board supports three kinds of clock sources as the MCU clock For details refer to the H8SX 1650 E6000H Emulator User s Manual HS1650EPH60HE To use the emulator internal clock Select the clock in the emulator by the CLOCK command emulator command To use the external clock on the user system Supply the external clock from the user system to the emulator by inputting the EXTAL pin pin 84 on the user system interface board or connecting the crystal oscillator to the XTAL pin 83 and EXTAL pins For details refer to the H8SX 1650 Hardware Manual Figure 14 shows the clock oscillator on the user system interface board 1 Mo HCU04 To E6000H emulator O O EXTAL XTAL System clock Figure 14 Clock Oscillator RENESAS To use the crystal oscillator mounted on the evaluation chip board Install the crystal oscillator into the crystal oscillator terminals on the evaluation chip board Enlarged view Crystal oscillator Crystal oscillator terminals Evaluation chip board Figure 15 Installing t
4. e User system interface board HS1653ECN61H The user system or a host computer is not included in this definition Purpose of the User System Interface Board This user system interface board is for connecting the evaluation chip board and user system This user system interface board must only be used for the above purpose Improvement Policy Renesas Technology Corp including its subsidiaries hereafter collectively referred to as Renesas pursues a policy of continuing improvement in design performance functions and safety of the user system interface board Renesas reserves the right to change wholly or partially the specifications design user s manual and other documentation at any time without notice Target User of the User System Interface Board This user system interface board should only be used by those who have carefully read and thoroughly understood the information and restrictions contained in the user s manual Do not attempt to use the user system interface board until you fully understand its mechanism It is highly recommended that first time users be instructed by users that are well versed in the operation of the user system interface board RENESAS LIMITED WARRANTY Renesas warrants its user system interface boards to be manufactured in accordance with published specifications and free from defects in material and or workmanship Renesas will repair or replace any user system interface boards determ
5. system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST 1 Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance 2 Always switch OFF the E6000H emulator and user system before connecting or disconnecting any CABLES or PARTS 3 Always before connecting any BOARDS make sure that pin 1 on both sides are correctly aligned RENESAS Preface The HS1653ECN61H is a user system interface board that connects a user system for the H8SX 1653 TFP 120 package to the H8SX 1650 E6000H emulator HS 1650EPH60H Emulation of the H8SX 1653 group is only possible when this user system interface board is connected to the HS1650EPH60H RENESAS Contents Section oie soes eds aa Es Ge Re Ge DO n ae Gide 1 Section 2 Connection PIGEBE SS se se Ee GE EES Ee ER Ee Oo Ge EEN es 3 2 1 Connecting User System Interface Board to User System 3 2 1 1 Installing CSocket 5 dus cient GEE SEE ESE SR EE De GE ee EN havens 4 2 1 2 Soldering IC SOCK EE RE EE EE E rE EEEa En 4 2 1 3 Installing IC Socket ends GR EA Bee RS vena 4 2 1 4 Fastening IC Socket Connector ss 5 2 2 Exchanging the Spacer of the Evaluation Chip Board 7 2 3 Connecting User System Interface Board to Evaluation Chip Board iese ese esse esse ee 8 2 4 Recommended Dimensions for User System Mount Pad Footprint 10 2 5 Dimensions for E
6. REJ10B0200 0200 Everywhere you imagine ad N ESAS H8SX 1653 Group E6000H TFP 120 User System Interface Board HS1653ECN61H Users Manual Renesas Microcomputer Development Environment System HS1653ECN61HE Rev 2 00 Renesas Technology Revision Date Dec 09 2005 www renesas com Keep safety first in your circuit designs Renesas Technology Corp puts the maximum effort into making semiconductor products better and more reliable but there is always the possibility that trouble may occur with them Trouble with semiconductors may lead to personal injury fire or property damage Remember to give due consideration to safety when making your circuit designs with appropriate measures such as i placement of substitutive auxiliary circuits ii use of nonflammable material or iii prevention against any malfunction or mishap Notes regarding these materials These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp product best suited to the customer s application they do not convey any license under any intellectual property rights or any other rights belonging to Renesas Technology Corp or a third party Renesas Technology Corp assumes no responsibility for any damage or infringement of any third party s rights originating in the use of any product data diagrams charts programs algorithms or circuit application examples contained in these m
7. aterials All information contained in these materials including product data diagrams charts programs and algorithms represents information on products at the time of publication of these materials and are subject to change by Renesas Technology Corp without notice due to product improvements or other reasons It is therefore recommended that customers contact Renesas Technology Corp or an authorized Renesas Technology Corp product distributor for the latest product information before purchasing a product listed herein The information described here may contain technical inaccuracies or typographical errors Renesas Technology Corp assumes no responsibility for any damage liability or other loss rising from these inaccuracies or errors Please also pay attention to information published by Renesas Technology Corp by various means including the Renesas Technology Corp Semiconductor home page http www renesas com When using any or all of the information contained in these materials including product data diagrams charts programs and algorithms please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products Renesas Technology Corp assumes no responsibility for any damage liability or other loss resulting from the information contained herein Renesas Technology Corp semiconductors are not designed or manufactured for use in a device or syst
8. correct usage will cause damage to the emulator product user system interface board and user system 21 RENESAS Section 6 Restrictions There are the following restrictions on emulation of the H8SX 1653 group when the user system interface board is connected to the emulator 1 The USB clock frequency is fixed to 48 MHz regardless of the EXTAL input 2 P14 cannot be used as a port if the serial output function has already been selected The port pin state cannot be read from the port register 22 RENESAS Renesas Microcomputer Development Environment System User s Manual H8SX 1653 Group E6000H TFP 120 User System Interface Board HS1653ECN61H Publication Date Rev 1 00 November 11 2004 Rev 2 00 December 9 2005 Published by Sales Strategic Planning Div Renesas Technology Corp Edited by Customer Support Department Global Strategic Communication Div Renesas Solutions Corp 2005 Renesas Technology Corp All rights reserved Printed in Japan Renesas Technology Corp Sales Strategic Planning Div Nippon Bldg 2 6 2 Ohte machi Chiyoda ku Tokyo 100 0004 Japan TENESAS RENESAS SALES OFFICES http www renesas com Refer to http www renesas com en network for the latest and detailed information Renesas Technology America Inc 450 Holger Way San Jose CA 95134 1368 U S A Tel lt 1 gt 408 382 7500 Fax lt 1 gt 408 382 7501 Renesas Technology Europe Limited Dukes Meadow Millboard R
9. em that is used under circumstances in which human life is potentially at stake Please contact Renesas Technology Corp or an authorized Renesas Technology Corp product distributor when considering the use of a product contained herein for any specific purposes such as apparatus or systems for transportation vehicular medical aerospace nuclear or undersea repeater use The prior written approval of Renesas Technology Corp is necessary to reprint or reproduce in whole or in part these materials If these products or technologies are subject to the Japanese export control restrictions they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination Any diversion or reexport contrary to the export control laws and regulations of Japan and or the country of destination is prohibited Please contact Renesas Technology Corp for further details on these materials or the products contained therein IMPORTANT INFORMATION READ FIRST e READ this user s manual before using this user system interface board e KEEP the user s manual handy for future reference Do not attempt to use the user system interface board until you fully understand its mechanism User System Interface Board Throughout this document the term user system interface board shall be defined as the following product produced only by Renesas Technology Corp excluding all subsidiary products
10. he Clock Oscillator RENESAS 19 Section 5 Notice 1 Before connecting any parts or cables make sure that pin 1 on the both sides are correctly aligned 2 Do not apply excessive force to the user system interface board while it is connected to the user system 3 The dimensions of the recommended mount pad for the IC socket for this user system interface board are different from those of the MCU 4 This user system interface board is specifically designed for the HS1650EPH60H emulator Do not use this board with any other emulator 5 When power is not supplied to the Vcc pin on the user system interface board the emulator displays VCC DOWN The emulator will not operate correctly 6 The P1 jumper socket is used for testing Do not remove the inserted jumper pin Do not remove the jumper pin Figure 16 Jumper Socket 7 Do not connect this user system interface board to the user system for the H8SX 1650 group 20 RENESAS 8 When this emulator is used without connecting to the user system ensure that the SW1 jumper pin is inserted to OFF Failure to do so will damage the emulator product user system interface cable and user system 9 To connect the emulator to the user system ensure that the SW1 jumper pin is inserted to ON Failure to do so will damage the emulator product user system interface board and user system 10 Do not connect a 5 V signal to any pin including the USB pins In
11. he above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may have other rights which may vary from state to state The Warranty is Void in the Following Cases Renesas shall have no liability or legal responsibility for any problems caused by misuse abuse misapplication neglect improper handling installation repair or modifications of the user system interface board without Renesas prior written consent or any problems caused by the user system All Rights Reserved This user s manual and user system interface board are copyrighted and all rights are reserved by Renesas No part of this user s manual all or part may be reproduced or duplicated in any form in hard copy or machine readable form by any means available without Renesas prior written consent Other Important Things to Keep in Mind 1 Circuitry and other examples described herein are meant merely to indicate the characteristics and performance of Renesas semiconductor products Renesas assumes no responsibility for any intellectual property claims or other problems that may result from applications based on the examples described herein 2 No license is granted by implication or otherwise under any patents or other rights of any third party or Renesas Figures Some figures in this user s manual may show items different from your actual system Limited Anticipation of Danger Renesas cannot anticipa
12. ined to be defective in material and or workmanship User system interface boards are wearing parts which Renesas will not repair or replace if damaged and or worn through use The foregoing shall constitute the sole remedy for any breach of Renesas warranty This warranty extends only to you the original Purchaser It is not transferable to anyone who subsequently purchases the user system interface board from you Renesas is not liable for any claim made by a third party or made by you for a third party DISCLAIMER RENESAS MAKES NO WARRANTIES EITHER EXPRESS OR IMPLIED ORAL OR WRITTEN EXCEPT AS PROVIDED HEREIN INCLUDING WITHOUT LIMITATION THEREOF WARRANTIES AS TO MARKETABILITY MERCHANTABILITY FITNESS FOR ANY PARTICULAR PURPOSE OR USE OR AGAINST INFRINGEMENT OF ANY PATENT IN NO EVENT SHALL RENESAS BE LIABLE FOR ANY DIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE USER SYSTEM INTERFACE BOARD THE USE OF ANY USER SYSTEM INTERFACE BOARD OR ITS DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES EXCEPT AS EXPRESSLY STATED OTHERWISE IN THIS WARRANTY THIS USER SYSTEM INTERFACE BOARD IS SOLD AS IS AND YOU MUST ASSUME ALL RISK FOR THE USE AND RESULTS OBTAINED FROM THE USER SYSTEM INTERFACE BOARD 2ENESAS State Law Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages so t
13. oad Bourne End Buckinghamshire SL8 5FH U K Tel lt 44 gt 1628 585 100 Fax lt 44 gt 1628 585 900 Renesas Technology Shanghai Co Ltd Unit 205 AZIA Center No 133 Yincheng Rd n Pudong District Shanghai 200120 China Tel lt 86 gt 21 5877 1818 Fax lt 86 gt 21 6887 7898 Renesas Technology Hong Kong Ltd 7th Floor North Tower World Finance Centre Harbour City 1 Canton Road Tsimshatsui Kowloon Hong Kong Tel lt 852 gt 2265 6688 Fax lt 852 gt 2730 6071 Renesas Technology Taiwan Co Ltd 10th Floor No 99 Fushing North Road Taipei Taiwan Tel lt 886 gt 2 2715 2888 Fax lt 886 gt 2 2713 2999 Renesas Technology Singapore Pte Ltd 1 Harbour Front Avenue 06 10 Keppel Bay Tower Singapore 098632 Tel lt 65 gt 6213 0200 Fax lt 65 gt 6278 8001 Renesas Technology Korea Co Ltd Kukje Center Bldg 18th FI 191 2 ka Hangang ro Yongsan ku Seoul 140 702 Korea Tel lt 82 gt 2 796 3115 Fax lt 82 gt 2 796 2145 Renesas Technology Malaysia Sdn Bhd Unit 906 Block B Menara Amcorp Amcorp Trade Centre No 18 Jalan Persiaran Barat 46050 Petaling Jaya Selangor Darul Ehsan Malaysia Tel lt 603 gt 7955 9390 Fax lt 603 gt 7955 9510 Colophon 5 0 H8SX 1653 Group E6000H TFP 120 User System Interface Board HS1653ECN61H User s Manual sTENESAS Henssas ae ne ooy am 2 6 2 Ote machi Chiyoda ku Tokyo 100 0004 Japan
14. socket from being damaged by twisting the components RENESAS Screws M2 x 12 mm with flat washers for fastening cable head User system interface board Pin 1 IC socket IC149 120 043 B51 manufactured by User system YAMAICHI ELECTRONICS Co Ltd Figure 2 Connecting User System Interface Board to User System RENESAS 2 2 Exchanging the Spacer of the Evaluation Chip Board While the user system interface board is connected to the user system be careful not to apply load Exchange the spacer 2 6MP x 10 mm of the evaluation chip board with another spacer 2 6MP x 25 mm provided for the user system interface board Evaluation chip board Spacer 2 6MP x 25 mm Figure 3 Exchanging the Spacer RENESAS 2 3 Connecting User System Interface Board to Evaluation Chip Board WARNING Observe the precautions listed below Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST 1 Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected to or removed from any part Before connecting make sure that pin 1 on both sides are correctly aligned 2 The user system interface board dedicated to the emulator must be used 1 Make sure that power of the user system and the emulator is turned off
15. stening cable head with four flat washers Screw M2 x 8 mm 4 For installing a TFP 120 packaged MCU with four flat washers 6 Spacers 2 6MP x 25 mm 2 7 Spacers 2 6MO x 16 mm 4 Users manual 1 User s manual for HS1653ECN61H this manual 2 RENESAS Section 2 Connection Procedures 2 1 Connecting User System Interface Board to User System WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected to or removed from any part Before connecting make sure that pin 1 on both sides are correctly aligned Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST CAUTION 1 Do not connect a 5 V signal to any pin including the USB pins Incorrect usage will cause damage to the emulator product user system interface board and user system To connect the emulator to the user system ensure that the SW1 jumper pin is inserted to ON Failure to do so will damage the emulator product user system interface board and user system RENESAS To connect the cable head to the user system follow the instructions below 2 1 1 Installing IC Socket After checking the location of pin 1 on the IC socket apply epoxy resin adhesive to the bottom of the IC socket for a TFP 120 package and fasten it to the user system before soldering 2 1 2 Soldering IC Socke
16. t After fastening solder the IC socket for a TFP 120 package to the user system Be sure to completely solder the leads so that the solder slops gently over the leads and forms solder fillets Use slightly more solder than the MCU 2 1 3 Installing IC Socket CAUTION Check the location of pin 1 before inserting After checking the location of pin 1 on the user system interface board and pin 1 on the IC socket connector align the guide pins on the IC socket connector with the guide holes on the user system interface board and insert the IC socket connector into the IC socket figure 2 RENESAS Fastening IC Socket Connector CAUTION Use the screwdriver provided for tightening screws The tightening torque must be 0 294 Nem or less If the applied torque cannot be accurately measured stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening If a screw is tightened too much the screw head may break or an IC socket contact error may be caused by a crack in the IC socket solder If the emulator does not operate correctly cracks might have occurred in the solder Check conduction with a tester and re solder the IC socket if necessary Fasten the user system interface board to the IC socket on the user system with four screws M2 x 12 mm provided Take special care such as manually securing the IC socket soldered area to prevent the soldered IC
17. te every possible circumstance that might involve a potential hazard The warnings in this user s manual and on the user system interface board are therefore not all inclusive Therefore you must use the user system interface board safely at your own risk N RENESAS SAFETY PAGE READ FIRST e READ this user s manual before using this user system interface board e KEEP the user s manual handy for future reference Do not attempt to use the user system interface board until you fully understand its mechanism DEFINITION OF SIGNAL WORDS A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury A WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage NOTE emphasizes essential information lt 2tENESAS WARNING Observe the precautions listed below Failure to do so will result in a FIRE HAZARD and will damage the user
18. to the connector CN1 on the board 13 RENESAS swi USER D ON OFF Spacer 2 6MQ x 16 mm Figure 9 Attaching Spacers RENESAS Section 3 User System Interface Circuits The following user interface circuits are required for the emulator when the user system interface board is in use Sub MCU Vec User system MD control Sonat Monitoring circuit circuit LPT16244 MD_CLK PMO PM4 EPM7128 VBUS DrVcc circuit USD USD DrVss I Figure 10 User System Interface Circuit 1 Note The power supply circuit shown above is turned on off by the setting of the SW1 jumper pin on HS1653ECN61H Ensure that the jumper pin is inserted to ON on HS1653ECN61H when connecting the emulator with HS1653ECN61H attached to the user system or supplying power to DrVCC Otherwise the emulator product user system interface board and user system will be damaged 15 RENESAS MCU User system SN74CB3Q3306A P23 SN74CB3Q3306A P27 Figure 11 User System Interface Circuit 2 MCU User system SN74CB3Q3306A P14 Sub MCU SN74CB3Q3306A Figure 12 User System Interface Circuit 3 RENESAS MCU Vcc User system EPM7128 HC14 VHC244 UHC 47ko _RES EPM7128 Figure 13 User System Interface Circuit 4 RENESAS 17 Section 4 Verifying Operation 1 Turn on the emulator according to the procedures described in the
19. valuation Chip Board and User System Interface Board iese esse ese 11 2 6 Resulting Dimensions after Connecting User System Interface Board 12 2 7 Using the Emulator without Connecting User System 13 Section 3 User System Interface CIFOUES ie sasie ese GERS RE OS KS es N se bo 15 Section 4 Verifying Operation issie esse ase se Re Re es ee GE Red be Ee ede Ke EE 18 Sect n S ie RR ER EE 20 Section 6 REStICHONS ese eg nl RR ae ED Eko Re ee Dene 22 il RENESAS Section 1 Configuration Figure 1 and table 1 show the configuration and components of the user system interface board for the TFP 120 package Please make sure you have all of these components when unpacking Evaluation chip board Screws M2 x 8 mm with flat washers Spacer JL Screws M2 x 12 mm with flat washers for fastening cable head User system interface board Socket cover IC socket User system Figure 1 User System Interface Board for the H8SX 1653 TFP 120 Package RENESAS Table 1 CAUTION Use an 1C149 120 043 B51 socket manufactured by YAMAICHI ELECTRONICS Co Ltd for the TFP 120 package IC socket on the user system No Component 7 User system interface board HS1653ECN61H Components Quantity Remarks 1 2 IC socket 1 For the TFP 120 package to be mounted on the user system Socket cover 1 For installing a TFP 120 packaged MCU Screw M2 x 12 mm 4 For fa
Download Pdf Manuals
Related Search