Home

Regency LIBERTY L676E-NG User's Manual

1. with each approved venting system bh it is highly recommended to apply Mill Pac sealant supplied to every inner pipe connec tion Failure to do so may result in drafting or performance issues not covered under Diagram 7 2 2 gt E gt Z warranty Silicone red RTV is optional Female 7 Locking Lugs NOTE A Vent Guard is required when the AstroCap is installed above grade at 7 feet or lower Mill Pac 1 TUT TAN j Male 3 Locking Diagram 1 Lugs oe Regency L676E Direct Vent Gas Fireplace 23 INSTALLATION UNIT INSTALLATION 4 Assemble the desired lengths of pipe and elbows Ensure that all pipes and elbow WITH VERTICAL connections are in the fully twist locked position and sealed 5 TERMINATION qz Rigid Vent Systems Note For best results and optimum lt performance with each approved venting Note clearance of 2 51mm must be system it is highly recommended to apply lt maintained except when passing Mill Pac sealant supplie
2. HEC Vent Termination Air Supply Outlet Area where terminal is not permitted A Clearance above grade veranda porch deck or balcony min 12 30cm B Clearance to window or door that may be opened 12 30cm 9 23cm C Clearance to permanently closed window min 12 30cm D Vertical clearance to ventilated soffit located above the terminal within a horizontal distance of 24 60cm from the centerline of the terminal min 24 60cm check with local code E Clearance to unventilated soffit min 24 60cm F Clearance to outside corner with AstroCap Termination Cap min 13 with Dura Vent Termination Cap 13 G Clearance to inside corner with AstroCap Termination Cap min 13 with Dura Vent Termination Cap 13 H Not to be installed above a meter regulator assembly within 3 90 horizontally from the centerline of the regulator J Clearance to service regulator vent outlet min 36 90cm K Clearance to non mechanical air supply inlet to building or the combustion air inlet to any other appliance 12 30cm 9 23cm L Clearance to a mechanical air supply inlet min 72 1 8m 3 91cm above if within 10 3m horizontally Clearance above paved sidewalk or a paved driveway located on public property min 84 2 1m N Clearance under veranda porch deck or balcony min 24 60cm Note Excluding direct vent or non condensing appliances a vent shall not terminate direc
3. lt ep Z High Wind Vertical Cap N A N A High Wind Horizontal Cap DISC N A Horizontal Square Termination Cap N A 5DT HHC Vertical Termination Cap N A 5DT HVC Storm Collar 58DVA SC 5DT SC Adjustable Flashing 0 12 6 12 58DVA F6 1243 5DT AF6 SPE Adjustable Flashing 6 12 12 12 58DVA F12 12435 5DT AF12 5DF 12 Vinyl Siding Standoff 58DVA VSS 1250 5DT VS 5DVS Vinyl Siding Shield Plate N A N A 5DT VSP N A Snorkel Termination 14 58DVA SNK14 1282 5DT ST14 5DST14 Snorkel Termination 36 N A 1281 5DT ST36 5DST36 Restrictor Disk 58DVA RD N A N A N A Colinear Flex Liner Adapter 3 N A N A N A N A FPI 946 604 P Simpson Direct Vent Vent Guard Optional 946 623 P AstroCap XL Horizontal Cap 770 994 Rigid Pipe Adapter Must use with all Rigid Piping 946 506 P Vent Guard Optional NOTE When using Metal Fab Sure Seal Rigid Piping please note that either the Adaptor 5DDA or 90 Starter Elbow SD90A must be used in conjunction with Rigid Pipe Adaptor 770 994 676 amp L900 Direct Vent Fireplace IMPORTANT NOTE A Vent Guard is required when the AstroCap is installed above grade at 7 feet or lower e The Simpson Dura Vent and Selkirk Direct Temp horizontal termination caps cannot be used in any applications Only the AstroCap XL and Snorkels are certified for horizontal terminations Offset Pipe Selection Use this table to determine offset pipe lengths For specific instructions or details
4. 2 Horizontal Feet lt The shaded area the diagram shows all allowable combinations of straight vertical and offset to vertical 0 2 4 6 8 10 12 14 lt terminations using two 90 elbows with Rigid Pipe I 1 n Venting Systems for Propane and Natural Gas i 4 Two 45 elbows equal to 90 elbow Maximum of four 45 elbows allowed A I I 1 A N S 1 l 1 E GE BI 27 A l 11 a i 7 Td A A gt mm p Im ee ee ey s 7 DA ds ET l 1 Vent Restrictor on Set 3 gt ED R ra D E I J 2 U l o 1 N ES p 5 E O gt 1 1j I I I an T I 0 I I I I Vent must be supported at offsets e Firestops required at each floor level and whenever passing through wall e Maintain clearances to combustibles as listed in the Clearances section e Vent Restrictor Position section for details on how to change the vent restrictor to Set 1 Set 2 or Set 3 if required Note Mustuse optional flue adapter when using Rigid Pipe Part 770 994 y y Y Minimum 12 305mm Max 10 3m centerline to centerline A
5. xelan Deeds 34 Shutdown 2 2 2 34 Normal Operating Sounds of Gas Appliances 34 Operation During Power Outage 34 Backup B NN is wade tbe 34 Copy of Lighting Plate Instructions 35 Maintenance Instructions 36 General Vent Maintenance 36 Log Replacement 36 Glass AK 36 MAINTENANCE Bore Mi Cl cR 36 Glass 36 Back Up Battery Replacement 37 Control Box Replacement 37 Valve Tray 39 PARTS LIST Main Assembly i bawk daa ka 42 Burner amp Log 43 WARRANTY The Warranty Limited Lifetime 47 Z e x lt ep Z SAFETY LABEL This is a copy of the label that accompanies each L676E NG and L676E LP Direct Vent Gas Fireplace We have printed copy of the contents here for your review The safety label is located on the right hand side of the unit visible when the exterior right side brick panel is removed NOTE Regency units are constantly being improved Check t
6. D E amp F Do not disconnect the the jumper cables labelled B 10 Replace the control box 11 Re connect wires harnesses Ensure that the cables match the letters labelled on the control box and are securely connected 12 Reinstall the ground screw 13 Reverse steps 8 to 1 38 Regency L676E Direct Vent Gas Fireplace VALVE TRAY REPLACEMENT 1 Remove the exterior brick panels 6 Remove the front burner by removing the screw 2 Remove the glass door a Release the 2 door latches on the left and right side at the top of the firebox Latch b Swing the door out from the top and release the hinges on the left and right side of the door by lifting them up Front Burner Removed 7 Remove the back burner by removing the screw Door lt gt 2 m 2 gt 2 2 E 3 Remove the log set 4 Remove the interior brick panels 5 Remove the grate by undoing the 2 screws on the left and right side 8 Remove the rear log stand by removing the 4 screws Rear Log Stand Grate Regency L676E Direct Vent Gas Fireplace 39 MAINTENANGE 9 Carefully remove the bottom brick panel 13 Disconnect the inlet gas line from the valve 14 Disconnect the 2 connectors from the modulating coil and the wire harness Wire Harness Bottom Brick Panel Connectors 10 Loosen the 2 screws that hold the right side heat shield in plac
7. The gas appliance and vent system must be vented directly to the outside of the building Vent Restrictor Set 0 and never be attached to chimney serving separate solid fuel or gas burning appliance Each direct vent gas appliance must use it s own separate vent system Common vent systems are prohibited factory set for NG units Latch VENT RESTRICTOR POSITION Vent restriction is required for certain venting installations see the diagrams in the Venting Arrangements section to determine if they are required for your installation b Swing the door outfrom the top and release Vent Restrictor Set 1 the hinges on the left and right side of the factory set for LP units door by lifting them up The Vent Restrictor plate is located on the inside top of the firebox Vent Restrictor Plate Door Vent Restrictor Set 2 2 Remove the screws that hold the vent restric tor plate in place 3 Adjustthe ventrestrictor plate to the required vent restrictor position as per the diagrams shown 4 Oncethe ventrestrictor plate is in the required position secure with screws Vent Restrictor Set 3 Regency L676E Direct Vent Gas Fireplace 13 Z e x lt ep Z INSTALLATION EXTERIOR VENT TERMINATION REQUIREMENTS Openable i
8. Non combustible Material Finished ar wm Exterior Brick Panel Non combustible Material 2 51mm NOTE No hearth is required when the unit is flush with the finished floor as shown below The minimum floor clearance must be maintained from the top surface of the carpet etc to the unit base Unit Sitting on Finished Floor Non combustible Material Finished Floor Regency L676E Direct Vent Gas Fireplace INSTALLATION 5 clearances listed below Minimum distances unless otherwise stated major cause of chimney related fires is failure to maintain required clearances air space to combustible materials It is of the greatest importance that this fireplace and vent system be installed only in accordance with these instructions Caution Requirements The top back and sides of the fireplace are defined by standoffs The metal ends of the standoff may NOT be recessed into combustible construction 2 2 gt Em gt Z Clearance to Combustibles from Back 0 0mm A Side 0 0mm ER Floor 0 0 NTT 0mm co e o N LO Minimum Clearance from Top of Front Facing Mantel min 16 1 2 419mm Ceiling 52 813mm from top of front facing Side Wall to Unit 15 381mm 15 rs 381mm Horizontal Vent Clearances to Combustibles 5 Top 2 76mm
9. 711mm 51mm 29 1 8 737mm 1 25mm O N O lt I O sr Regency L676E Direct Vent Gas Fireplace IMPORTANT MESSAGE SAVE THESE INSTRUCTIONS The L676E Direct Vent Fireplace must be installed in accordance with these instructions Carefully read all the instructions in this manual first Consult the authority having jurisdiction to determine the need for a permit prior to starting the installation It is the responsibility of the installer to ensure this fireplace is installed in compliance with manufacturers instructions and all applicable codes BEFORE YOU START Safe installation and operation of this appliance requires common sense however we are required by the Canadian Safety Standards and ANSI Standards to make you aware of the following INSTALLATION AND REPAIR SHOULD BE DONE BY AN AUTHORIZED SERVICE PERSON THE APPLIANCE SHOULD BE INSPECTED BEFORE USE AND AT LEAST ANNUALLY BY A PROFESSIONAL SERVICE PERSON MORE FREQUENT CLEANING MAY BE REQUIRED DUE TO EXCESSIVE LINT FROM CARPETING BEDDING MATERIAL ETC IT IS IMPERATIVE THAT CONTROL COMPARTMENTS BURNERS AND CIRCULATING AIR PASSAGEWAYS OF THE APPLIANCE BE KEPT CLEAN DUE TO HIGH TEMPERATURES THE APPLIANCE SHOULD BE LOCATED OUT OF TRAFFIC AND AWAY FROM FURNITURE AND DRAPERIES WARNING FAILURE TO INSTALL THIS APPLIANCE CORRECTLY WILL VOID YOUR WARRANTY AND MAY CAUS
10. 2 Check to see that all wiring is correct and enclosed to prevent possible shock 3 Check to ensure there are no gas leaks 4 Make sure the glass in the door frame is properly positioned Never operate the appliance with the glass removed 5 Verify that the venting and cap are unobstructed Ensure that the brick panels are installed 7 Verify log placement If the pilot cannot be seen when lighting the unit the logs have been incorrectly positioned 8 The unit should never be turned off and on again without minimum of 60 second wait FIRST FIRE The FIRST FIRE in your heater is part ofthe paint curing process To ensure the paint is properly cured it is recommended you burn yourfireplace for at least four 4 hours the first time When first operated the unit will release an odour caused by the curing of the paint and the burning off of any oils remaining from manufac turing Smoke detectors in the house may go off at this time Open a few windows to ventilate the room for couple of hours The glass may require cleaning NOTE The main burner will always start on HIGH and resume it s last setting after 20 seconds of operation NOTE When the glass is cold and the appliance is lit it may cause condensation and fog the glass This condensation is normal and will disappear in few minutes as the glass heats up DO NOT BURN THE APPLIANCE WITHOUT THE GLASS FRONT IN PLACE DO NOT ATTEMPT TO C
11. FIREPLACE PRODUCTS REGENCY www regency fire com LIBERTY L676E Gas Fireplace fale Installation Manual mer kU 1 1 NA Unit requires 120V to operate See Wiring Diagram section in manual for more details Receptacle is included with manual package MODELS L676E NG Natural Gas L676E LP Propane WARNING Ifthe information in these instructions are not followed exactly What to do if you smell gas a fire or explosion may result causing property damage Do not try to light any appliance personal injury or loss of life Do not touch any electrical switch do not use any phone in your FOR YOUR SAFETY building Do not store or use gasoline or other flammable vapors and Immediately call your gas supplier liquids in the vicinity of this or any other appliance from a neighbour s phone Follow the gas supplier s instructions Installation and service must be performed by a qualified If you cannot reach your gas installer service agency or the gas supplier supplier call the fire department Installer Please complete the details on the back cover and leave this manual with the homeowner Homeowner Please keep these instructions for future reference 918 621a FPI FIREPLACE PRODUCTS INTERNATIONAL LTD 6988 Venture St Delta BC Canada V4G 1H4 03 14 08 To the New Owner Congratulations You are the owner of a state of the art Gas Fireplace by REGENCY The L676E has been design
12. Mandatory in all Horizontal Terminations 4 8 W y AV AY A A A 00 if required art 4946 506 P AstroCap XL Termination Cap Part 946 623 P 8 dia _ Flue pipe A Vent Guard is required when the AstroCap is installed above grade at 7 feet or lower Notes 1 Liner sections should be continuous without any joints or seams 2 Only Flex pipe purchased from may be used for Flex installations 3 Horizontal vent mustbe supported every 3 feet 4 A wall thimble is mandatory for all horizontal terminations due to high temperatures Regency L676E Direct Vent Gas Fireplace 15 INSTALLATION RIGID PIPE VENTING SYSTEMS BASIC HORIZONTAL amp VERTICAL TERMINATIONS Z N lt M Vertical CO Rigid Pipe Vent Systems offer a complete DE lt line of component parts for installation of both horizontal and vertical installations Many items Storm Collar lt gt 6 offered decorative black as well as gal Z vanized finish Vinyl Siding Flashing Standoff Optional The minimum components required for a basic T horizontal termination are Ceiling Firesto 1 Horizontal Termination Cap i 5 Termination 1 Rigid Pipe Adaptor E Wall Thimble Mandatory in all P Vel Har 1 Length of pipe to suit wall thickness Pipe Length Adi Pipe Lenath d Adj Pipe Leng
13. 22 L676E Direct Vent Gas Fireplace INSTALLATION Horizontal runs of vent must be supported every 3 feet 0 9meter Wall straps are available for this purpose 7 Ensure that the pipe clearances to combustible materials are maintained Diagram 5 Install the termination cap UNIT INSTALLATION WITH HORIZONTAL TERMINATION Note If installing termination on vinyl 6 Mark the wall for 11 x 11 279mm x Rigid Vent Systems Note top clearance of 3 76mm and side amp bottom clearance of 2 51mm must be maintained except when passing through a wall ceiling or at the termination where the use of a firestop or wall thimble reduces the required clearance to 1 1 2 38mm Werecommend framing a 11 279mm x 11 279mm inside dimensions hole to give structural rigidity for 279mm square hole The center of the square hole should line up with the center line of the horizontal pipe Cut and frame the 11 inch 279mm square hole in the exterior wall where the vent will be terminated See diagram 2 for center line requirements If the wall being penetrated is constructed of non combustible material i e masonry block or concrete an 8 203mm diameter hole is acceptable siding covered wall a vinyl siding standoff orfurring strips mustbe used to ensure that the termination is not recessed into the siding Siding sealant al
14. as products evolve field modifications or upgrades will not be performed FPI will not be liable for travel costs for service work Installation and environmental problems are not the responsibility of the manufacturer and therefore are not covered under the terms of this warranty policy Embers gaskets and paint are not covered under the terms of this warranty policy Any unit which shows signs of neglect or misuse is not covered under the terms of this warranty policy The warranty will not extend to any part which has been tampered with or altered in any way or in our judgment has been subject to misuse improper installation negligence or accident spillage or downdrafts caused by environmental or geographical conditions inadequate ventilation excessive offsets negative air pressure caused by mechanical systems such as furnaces fans clothes dryer etc Freight damage to stoves and replacement parts is not covered by warranty and is subject to a claim against the freight carrier by the dealer FPI will not be liable for acts of God or acts of terrorism which cause malfunction of the appliance Performance problems due to operator error will not be covered by this warranty policy Products made or provided by other manufacturers and used in conjunction with the operation of this appliance without prior authorization from FPI may nullify your warranty on this product Any alteration to the unit which causes sooting or carboning that
15. 12 3 kW PROPANE GAS FIREPLACE MODEL L676E LP Factory Equipped For Altitude 0 4500ft 0 1372m r Min Supply Pressure 12 WC 2 98 kpa meo Low Setting Man Pressure 3 6 WC 2 49 kpa r Max Manifold Pressure 10 WC 2 98 kpa ta Orifice Size Front Burner 56 DMS Orifice Size Back Burner 53 DMS Y Minimum Input 9 000 Btu h 2 64 kW Maximum Input 40 000 Btu h 11 72 kW VENTED GAS FIREPLACE This appliance must be installed in accordance with the manufacturer s installation instructions and with local codes if any if none follow the current ANSI Z223 1 in the USA or the current CAN 1 B149 in Canada This vented gas fireplace is not for use with air filters For Manufactured Home Installation This Direct Vent System Appliance must be installed in accordance with the manufacturer s installation instructions and Manufactured Home Construction and Safety Standard Title 24 CFR Part 3280 or the current Standard for Fire Safety Criteria for Manufactured Home Installation Sites and Communities ANSI NFPA 501A and with CAN CSA Z240 MH Mobile Home Standard in Canada This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket permanently located manufactured mobile home where not prohibited by local codes See owner s manual for details This appliance is not convertible for use with other gases unless a certified kit is used Kit 2521 969 Certif
16. current National Electrical Code ANSI NFPA 70 in the U S A and the current CAN CGA 8149 Gas Installation Code and the current Canadian Electrical Code CSA C22 1 in Canada This appliance comes equipped with a dedicated 8 Ground Lug for attachment of the ground wire to the steel chassis as applicable to local codes The appliance when installed must be electrically grounded in accordance with local codes or in the absence of local codes with the National Electrical Code ANSI NFPA 70 or the Canadian Electrical Code CSA C22 1 This appliance may only be installed in an aftermarket permanently located manufactured U S A only or mobile home where not prohibited by local codes This appliance can only be used with the type of gas indicated on the rating plate This appliance is not convertible for use with other gases unless a certified kit is used Ensure that structural members are not cut or weakened during installation mL en We recommend that our products be INSTITUTE installed and serviced by professionals who are certified in the U S by the National Fireplace Institute NFI ONE REGENCY ONE TREE For each Regency sold we plant a tree AmericanForests org Technical Training or in Canada by Wood Energy Technical Wood Energy CERTIFIED Training WETT 2 L676E Direct Vent Gas Fireplace SAFETY LABEL Copy of Safety 4
17. on particular 5 x 8 Venting venting components please visit the following websites Pipe Length Run X Rise Y 0 0mm 5 11 16 144mm 15 5 16 389mm Selkirk Direct Temp www selkirkcorp com 6 152mm 8 1311 6 224 18 7 16 468mm A Metal Fab Sure Seal www mtlfab com 9 229mm 10 15 16 278mm MR 12 305mm 13 330mm 22 1146 576mm 2 24 610mm 21 7 16 697mm A 36 914mm 29 13 16 757mm 39 7 16 1002mm 48 1219mm 38 1 4 972 47 7 8 1216mm X NOTE Horizontal runs of vent must be level or have a 1 4 inch rise for every 1 foot of run towards the termination Never allow the vent to run downward This could cause high temperatures and may present a possible fire hazard 18 Regency L676E Direct Vent Gas Fireplace INSTALLATION VENTING ARRANGEMENTS ALLOWABLE HORIZONTAL TERMINATIONS The diagram shows all allowable combinations of vertical runs with horizontal terminations using 90 two 45 elbows equal 90 elbow Note Must use optional rigid pipe adapter Part 770 994 when using Rigid Pipe Venting Systems Horizontal Feet 7 f gt I 2 va 7 a 2 VVE 2 7 Vent Restrictor 7 AM m onSet1 D Vent Ta Z F on Set j A E 7 8 gt 2 2 7 7 va p g Vent Restric
18. with the equipment the instructions provided by the manufacturer for installation of the equipment and the venting system shall include 1 Detailed instructions for the installation of the venting system design or the venting system components and 2 complete parts list for the venting system design or venting system d MANUFACTURER REQUIREMENTS GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases but identifies special venting systems the following requirements shall be satisfied by the manufacturer 1 The referenced special venting system instructions shall be included with the appliance or equipment installation instructions and 2 The special venting systems shall be Product Approved by the Board and the instructions for that system shall include a parts list and detailed installation instructions e A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment all venting instructions all parts lists for venting instructions and or all venting design instructions shall remain with the appliance or equipment at the completion of the installation Regency L676E Direct Vent Gas Fireplace 5 UNIT DIMENSIONS 1 13mm INSTALLATION 47 1 2 1206mm 5 127mm Inner Dia 8 203mm Outer Dia 28 1 16
19. 1 INSTALLATION OF CARBON MONOXIDE DETECTORS At the time of installation of the side wall horizontal vented gas fueled equipment the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back up is installed on the floor level where the gas equipment is to be installed In addition the installing plumber or gasfitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling building or structure served by the side wall horizontal vented gas fueled equipment It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors a In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic the hard wired carbon monoxide detector with alarm and battery back up may be installed on the next adjacent floor level b In the event that the requirements of this subdivision can not be met at the time of completion of installation the owner shall have a period of thirty 30 days to comply with the above requirements provided however that during said thirty 30 day period a battery operated carbon monoxide detector with an alarm shall be installed 2 APPROVED CARBON MONOXIDE DETECTORS Each carbon monoxide detector as required in accordance with the abov
20. 1 2 419mm __ x 0 Top of 7 Front i Facing MANTEL LEG CLEARANCES Combustible mantel leg clearances as per diagram MANTEL LEG Allowable mantel leg projection Side wall 15 381mm 10 Regency L676E Direct Vent Gas Fireplace INSTALLATION FRAMING amp FINISHING 1 Frame in the enclosure for the unit with framing material The framed opening for the assembled kit is 45 7 8 high x 48 wide x 24 1 4 deep 1143mm x H 1219mm W x 616mm D See Diagram 1 Also see Diagram 2 for corner installations Metal Header t IMPORTANT Header must be metal stud 2 2 gt Em gt Z Non Combustible Material 5 Metal E e N 1 o 2007mm Min 24 1 4 616mm 9 45 718 1143mm 72 1829mm Diagram 3 2 For exterior walls insulate the enclosure to the same degree as the rest t of the house apply vapour barrier and drywall as per local installation E codes Do not insulate the fireplace itself O 3 The unit does not have to be completely enclosed chase You must maintain clearances from the vent to combustible materials See Clearances section Combustible materials can be laid against the 90 1 8 2292mm side and back standoffs and the stove base Diagram 2 Non Combustible Requirements 49 1 2 Metal Stud 1257mm C Non combustible Material 29 1 8 7
21. 311mm 2 x 4 or 2 x 6 5 dia fl 5 with ine sa me pl n 8 dia air intake Screws Vinyl Siding Wall Thimble Mandatory on all horizontal terminations 25 INSTALLATION INSTALLATION L676E NG SYSTEM DATA 5 WC 1 25 kpa 1 6 WC 0 39 kpa Min Supply Pressure Low Setting Man Pressure Max Manifold Pressure 3 5 WC 0 87 kpa Orifice Size Front 48 DMS Burner Orifice Size Back Burner 34 DMS 11 000 Btu h 3 22 kW 42 000 Btu h 12 3 kW L676E LP SYSTEM DATA 12 WC 2 98 kpa 3 6 WC 2 49 kpa Minimum Input Maximum Input Min Supply Pressure Low Setting Man Pressure Max Manifold Pressure 10 WC 2 98 kpa 56 DMS Orifice Size Front Burner Orifice Size Back Burner 53 DMS 9 000 Btu h 2 64 kW 40 000 Btu h 11 72 kW Minimum Input Maxiumm Input HIGH ELEVATION This unit is approved in Canada for altitude 0 to 4500 ft CAN1 2 17 M91 GAS LINE INSTALLATION Since some municipalities have additional local codes it is always best to consult with your local authorities and the CAN CGA B149 installation code For USA installations follow local codes and or the current National Fuel Gas Code ANSI 2223 1 When using copper or flex connectors use only approved fittings Always provide a union so that gas lines can be easily disconnected for servicing Flare nut
22. 37mm 28 1 16 711mm lt gt 10 3 16 254 Regency L676E Direct Vent Gas Fireplace 11 Z e x lt Z INSTALLATION UNIT ASSEMBLY PRIOR TO INSTALLATION The Top Facing Support the Side Nailing Strips and the 2 Top Standoffs must be correctly positioned and attached to the top before unit is slipped into position TOP STANDOFF ASSEMBLY The top standoffs are shipped in a flat position and must be folded into shape and attached 1 Remove the standoffs from the fireplace top 2 Take each standoff and bend into the correct shape Bend up at the bend lines until the screw holes in the standoff and the pre punched screw holes on the fireplace top line up 3 Attach the standoff securely to the top with 2 screws per standoff on opposite corners 1 Standoff Standoff after bending flat shipping position 12 SIDE NAILING STRIPS The side nailing strips come attached to the unit There are 3 plates one on the top and bottom that can be folded out as required Side Nailing Strips shown folded out FINISHING TEMPLATE In order to maintain clean face the L676E allows for a 1 8 in overlap of finishing material such as rock or tile on both the left and right hand sides of the unit top and bottom sides do not allow for an overlap this overlap must not be exceeded or
23. 8DVA 18B N A from FPI 1204 1204B 1203 1203B 1202 1202B 58DVA 60 58DVA 60B N A from FPI N A N A Disc See 58DV 08A Disc See 58DV 08AB Disc See 58DV 16A Disc See 58DV 16AB 58DVA 08A N A from 58DVA 08AB 58DVA 16A N A from FPI 58DVA 16AB 1245 1245B 12456 1245 58DVA E90 58DVA E90B Disc See 58DVA E90 Disc See 58DVA E90B N A N A Selkirk Metal Fab Direct Temp Sure Seal 506 oDT 6 oDT 6B oDT 9 oDT 9B 507 12 oDT 12B oDT 18 oDT 18B 5DT 24 oDT 24B SDT 36 oDT 36B 5DT 48 oDT 48B N A N A 2 2 gt E gt Z N A N A oDT AJ oDT AJB N A N A N A N A N A N A oDT EL45 N A 5SDT EL45B N A N A 50451 5D45LB SDT EL90S N A SDT EL90SB N A N A SDIOL N A 5D90LB N A 5D90A N A SDDA SDT CS SDT CSS SDT WS B SDT OS oDT WT N A SDT FS SDT TP 17 INSTALLATION Components from different Manufacturers may not be mixed Not All Rigid Pipe components are available directly from FPI Simpson Simpson Selkirk Metal Fab Descri ption Direct Vent Pro d Direct Temp Sure Seal Discontinued Round Support Radiation Sheild N A N A N A N A Flat Flashing N A N A N A N A Attic Insulation Shield 12 58DVA IS N A from 58DVA IS N A from Basic Horizontal Termination Kit A N A SDT HKA Horizontal Termination Kit B 58DVA KHA 5DT HKB Vertical Termination Kit 58DVA VCH 5DT VKC Z e x
24. E A SERIOUS HOUSE FIRE CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES ESPE CIALLY THE FIREPLACE GLASS AND SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION Regency L676E Direct Vent Gas Fireplace YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE CLOTHING OR OTHERFLAMMABLE MATERIALSHOULDNOTBEPLACED ON OR NEAR THE APPLIANCE GENERAL SAFETY INFORMATION 1 The appliance installation must conform with local codes or in the absence of local codes with the current Canadian or National Gas Codes CAN1 B149 or ANSI Z223 1 Installation Codes 2 The appliance when installed must be electrically grounded in accordance with local codes orin the absence oflocal codes with the current National Electrical Code ANSI NFPA 70 or CSA C22 1 Canadian Electrical Code 3 See general construction and assembly instructions The appliance and vent should be enclosed 4 This appliance must be connected to the specified vent and termination cap to the outside ofthe building envelope Never vent to another room or inside a building Make sure that the vent is fitted as per Venting instructions 5 Inspect the venting system annually for blockage and any signs of deterioration 6 Venting terminals shall not be recessed into a wall or siding 7 Any safety glass removed for servicing must be replaced prior to operating the applian
25. LEAN THE GLASS WHILE IT IS STILL HOT During the first few fires a white film may develop on the glass front as part of the curing process The glass should be cleaned after the unit has cooled down or the film will bake on and become very difficult to remove Use a non abrasive cleaner and DO NOTATTEMPT TO CLEAN THE GLASS WHILE IT IS HOT 33 U m 2 O 2 2 e x as TI 0 OPERATING INSTRUCTIONS LIGHTING PROCEDURE 1 Plug the power cord into power outlet 2 Press and release the ON OFF button once on the Remote Control 3 After approximately 3 seconds the spark ignition system will spark for 30 seconds to light the main burner 4 The unit will turn on NOTE If the unit does not turn on within 90 seconds of pressing the ON OFF button on the Remote Control this means that the system is in lockout mode The unit will need to be reset as follows a Remove the left side exterior brick panel b Hold the reset button for 3 to 5 seconds or until the LED stops blinking c Repeat step 2 For all other Remote Control features see FireWizard remote control operation manual SHUTDOWN PROCEDURE 1 Press release the ON OFF button once on the Remote Control 2 service is to be preformed you must disconnect both sources of powerto the unit main power and the battery 34 NORMAL OPERATING SOUNDS OF GAS APPLIANCES Itis possible that you will hear some sou
26. OL BOX ID CODE The Remote Control Handset has a set of unique ID codes that is pre programmed into its memory This set of ID codes helps to differentiate one Remote Control Handset from another so that only the control box with matching ID code will respond to the appropriate Remote Control Handset To ensure the remote control is matched to the receiver correctly please follow the steps below 1 Installthe 2 x AAA alkaline batteries into the Remote Control 2 Unplug and re plug the power cord The power cord is located on the left hand side of the appliance and will be plugged into the receptacle 3 Press and hold the PROG and FAN buttons simultaneously for up to 20 seconds During this time the remote will display LC while it is transmitting codes to the receiver 4 Once it is successfully transmitted wait for 20 seconds and press the ON OFF button on the remote control once and the burners will come on Ifis does not work the first time repeat steps 2 and 3 5 The remote control is now programmed to the receiver and the appliance can now be operated with it The control box will only learn the Remote ID codes during the first 30 seconds after power is applied and will ignore this special command from the Remote after the first 30 seconds NOTE This must only be performed by quali fied installer OPERATING INSTRUCTIONS 1 Read and understand these instructions before operating this appliance
27. REQUIREMENTS MA Code CO Detector for the State of Massachusetts only 5 UNIT DIMENSIONS Uit DIMENSIONS vas 6 INSTALLATION Important Message 2 2 2 Belore YOU SEN see 7 General Safety Information 7 Installation 2 7 Manufactured Mobile Home Additional Requirements 8 Locating Your Gas Fireplace 8 Heatwave Duct Kit 80012 8 Heat Release Kit vasre 8 Hearth Requirements 22 8 O 1 rs 9 Mantel Clearances 10 Mantel Leg Clearances 10 Framing amp FINISNING uiui oett ae te DER rane 11 Unit Assembly Prior To Installation 12 Top Standoff Assembly 12 Side Nailing Strips zU 12 Finishing Femplate nbsp ie Cb dec Ebr rave 12 Venting 22 221 13 Vent Restrictor Position 13 Exterior Vent Termination Requirements 14 Venting Arrangements 2 15 Horizontal Termination Flex 15 Rigid Pipe Vent
28. Side 2 51mm oo Bottom 2 51 mm es LEES COE JE E JE E XE CE JE TI i E m j j 1 j 1H rr 1 Vertical Vent Clearances to Combustibles All Sides 2 51mm 3 Alcove Clearances 76mm Min Depth 36 914mm Min Width 84 2134mm Min Height 84 2032mm Alcove side wall must have minimum of 15 381mm clearance on one side WARNING Fire hazard is an extreme risk if these clearances air space to combustible materials are not adhered to It is of greatest importance that this fireplace and vent system be installed only in accordance with these instructions Regency L676E Direct Vent Gas Fireplace 9 INSTALLATION MANTEL CLEARANGES Because of the extreme heat this fireplace emits the mantel clearances are critical Combustible mantel clearances from top of front facing are shown in the diagram below Note Anon combustible mantel may be installed at lower height if the framing is made of metal studs covered with non combustible board 141210 8 6 4 2 0 Note Ensure the paint that is used on the mantel and the facing is heat resistant or the paint may Z e x lt ep Z 13 330mm discolour 25 Drywall a yx Header V Metal Stud 15 Non combustible 1 25mm Facin 0 55 26 1 2 17 007 673 445mm Standoff 10 16
29. The minimum components required for a basic 11 14 5 8 vertical termination are 90 Elbow 1 Vertical Termination 1 Rigid Pipe Adaptor 24 Pipe 1 Lengths of pipe to adequately Length penetrate roof 1 Ceiling Firestop Rigid Pipe 1 Flashing Adapter 1 Storm Collar 770 994 Wall thickness is measured from the back standoffs to the inside mounting surface of termination cap For siding other than vinyl furring strips be used instead of the vinyl siding standoff to create level surface to mount the vent terminal The Terminal must not be recessed into siding Measure the wall thickness including furring strips Vent Guard is required when the AstroCap If a Vinyl Siding Standoff is required it must be used with vinyl siding measure to outside surface of wall without siding and add 2 inches is installed above grade at 7 feet or lower WARNING NOTE Me Do not combine venting components from The Simpson Dura Vent and Selkirk Direct different svstems Temp horizontal termination caps cannot g Sy Horizontal Termination be used in any applications Caps Use of the the AstroCap XL is acceptable Only the AstroCap XL and Snorkels are 8 with all systems certified for horizontal terminations Alternate Snorkel j This product has been evaluated by Intertek for Termination Cap using a Rigid Pipe Adaptor in conjunction with When using Rigid Vent other th
30. Tube Front Burner Tube 4 Place the left end of log 03 28 into the pin while resting the right end of the log on the grate Slide the right end of the log forward until it is approximately 3 8 away from the back side of the grate The 03 reference numbers i e 03 25 are molded into the rear of each log 1 Carefully remove the logs from the box and unwrap them The logs are fragile handle with care do not force into position 2 Place log 03 25 on the rear log support pins Backside of Grate 5 Line up the two holes on the underside of log 03 26 with the pins on logs 03 25 and 03 27 and fit in place 30 Regency L676E Direct Vent Gas Fireplace INSTALLATION 6 Spread all ofthe Embers on the bottom brick panel around the burner tube and inbetween the front burner tube and the grate as shown Separate platinum embers and place on the embers around the burner tube and inbetween the front burner tube and grate Avoid stacking platinum embers 2 2 gt Em gt 4 Z Embers in between front burner tube and grate 7 Spread the vermiculite on the base brick panel covering the remaining exposed base brick Embers on bottom brick panel Complete Log Set Installation Regency L676E Direct Vent Gas Fireplace 31 Z e x lt ep Z INSTALLATION A receptacle is provided on the left hand side of the unit 120 Volt AC power must be wired to the receptac
31. act measurements for clearances and floor protection before actually installing this appliance Have an authorized inspector dealer or installer review your plans before installation Note For vent terminations refer to Exterior Vent Termination Locations section HEATWAVE DUCT KIT The HeatWave Air Duct Kit increases the effectiveness of your fireplace by dispersing warm air from the fireplace to remote locations in the same room or other rooms in your home Up to two kits may be installed on the fireplace Please Note Only 1 HeatWave kit may be operated at one time See HeatWave installation manual for complete details and clearances from side only Heat Wave i The HeatWave Duct Kit has different clearance and framing requirements check the HeatWave manual for details Base of Unit HEAT RELEASE KIT The Heat Release Kit expels warm air from the fireplace to the outside of the building allowing the fireplace to be operated with less heat entering the room The kit may be used on either the left or right side See Heat Release installation manual for complete details and clearances from side only HEARTH REQUIREMENTS Aminimum 29 1 8 737mm wide x 12 305mm deep x 2 b1mm thick non combustible hearth is required if the finished floor is not flush with the base of the unit The maximum height between the finished floor and sub floor is 1 25mm Unit Sitting on Sub Floor
32. an Part 41282 1477 Duravent Direct Vent GS and Selkirk Direct Simpson Dura Vent 3 screws must be PEE Temp systems Use of these systems with used to secure rigid pipe to adaptor the Rigid Pipe adaptor is deemed acceptable and does not affect the Intertek WHI listing of components The AstroCap XL is certified for installations using venting systems as well as Simpson Dura Vent Direct Vent GS and Selkirk Direct Temp AstroCap XL is a proprietary trademark of Fireplace Products International Ltd Dura Vent and Direct Vent GS are registered and or proprietary trademarks of Simpson Dura Vent Co Inc 16 Regency L676E Direct Vent Gas Fireplace INSTALLATION 5 X 8 RIGID PIPE CROSS REFERENCE CHART Components from different Manufacturers may not be mixed Not All Rigid Pipe components are available directly from e ae Simpson 6 Pipe Length Galvanized 6 Pipe Length Black 9 Pipe Length Galvanized 9 Pipe Length Black 12 Pipe Length Galvanized 12 Pipe Length Black 18 Pipe Length Galvanized 18 Pipe Length Black 24 Pipe Length Galvanized 24 Pipe Length Black 36 Pipe Length Galvanized 36 Pipe Length Black 48 Pipe Length Galvanized 48 Pipe Length Black 60 Pipe Length Galvanized 60 Pipe Length Black Adjustable Length 3 10 Galvanized Adjustable Length 3 10 Black Adjustable Length 11 14 Galvanized Ad
33. ation Locate the unit in the framing rough in the gas preferably on the right side of the unit and the electrical Junction block is on the left side on the left Locate the centerline of the termination and mark wall accordingly Cut an 11 279mm hole in the wall inside dimension E oui Fairing AURA If installing termination siding covered wall a vinyl siding standoff or vinyl furring strips must be used to ensure that the termination is not recessed into the siding Level the fireplace and fasten it to the fram ing using nails or screws through the nailing strips Assemble the vent assembly by applying Mill Pac to the 5 127mm inner collar of the termination and slipping the 5 127mm liner over it at least 1 3 8 35mm Fasten with the 3 screws drilling pilot holes will make this easier Apply Mill Pac or high temperature silicone to the 8 203mm flex pipe and slip it over the 8 outer collar of the ventterminal atleast 1 3 8 35mm and fasten with the 3 screws NOTE Horizontal sections must be sup ported at intervals not exceeding 3 feet 0 9 meter Flame picture and performance will be affected by sags in the liner Regency L676E Direct Vent Gas Fireplace 4 5 6 7 8 9 Separate the 2 halves ofthe wall thimble and securely fasten the one with the tabs to the outside wall making sure that the tabs are on top and bottom Fasten the oth
34. ce 8 To prevent injury do not allow anyone who is unfamiliar with the operation to use the fireplace 9 Wearglovesand safety glasses for protection while doing required maintenance 10 Be aware of electrical wiring locations in walls and ceilings when cutting holes for termination 11 Under no circumstances should this appliance be modified Parts that have to be removed for servicing should be replaced prior to operating this appliance INSTALLATION 12 Installation and any repairs to this appliance should be done by an authorized service person Aprofessional service person should be called to inspect this appliance annually Make it a practice to have all of your gas appliances checked annually 13 Do not slam shut or strike the glass door 14 Under no circumstances should any solid fuels wood paper cardboard coal etc be used in this appliance 15 The appliance area must be kept clear and free of combustible materials gases and other flammable vapours and liquids Emissions from burning wood or gas could contain chemicals known to the State of California to cause cancer birth defects or other reproductive harm INSTALLATION CHECKLIST 1 Locate appliance a Room location Refer to Locating Your Gas fireplace section b Clearances to Combustibles Refer to Clearances section c Mantel Clearances Refer to Mantel Clearances section d Framing amp Finishing Requirements Ref
35. ck for evidences of excessive condensation such as water droplets forming in the inner liner and subsequently dripping outthe joints Continuous condensation can cause corrosion of caps pipe and fittings It may be caused by having excessive lateral runs too many elbows and exterior portions of the system being exposed to cold weather 4 Inspect joints to verify that no pipe sections or fittings have been disturbed and consequently loosened Also check mechanical supports such as Wall Straps or plumbers tape for rigidity LOG REPLACEMENT Theunitshould never be used with broken logs Turn off the gas valve and allow the unit to cool before opening door and carefully remove the logs The pilot light generates enough heat to burn someone If for any reason a log should need replacement you must use the proper replacement log The position of these logs must be as shown in the diagrams under Log Installation Note Improper positioning of logs may create carbon build up and will severely alter the unit s performance which is not covered under warranty GLASS GASKET If the glass gasket requires replacement use tadpole glass gasket Part 936 155 DOOR GLASS Your Regency fireplace is supplied with high temperature 5mm Ceramic glass If your glass requires cleaning we recommend using an approved glass cleaner available atall authorized dealers Do not use abrasive materials CAUTION amp WARNINGS Do
36. d to every inner through a wall ceiling or at the pipe connection Failure to do so may termination where the use ofafirestop result in drafting or performance issues not Minimum Vent Z or wall thimble reduces the required covered under warranty Silicone red RTV Roof Pitch Height clearance to 1 1 2 38mm We is optional recommend framing a 11 279mm x Feet Meters 11 279mm inside dimensions hole Female flat to 7 12 to give structural rigidity for mounting Jl Locking 21 N Lugs over 7 12 to 8 12 1 Maintain the 2 51mm th Mill Pac gt Silicone over 8 12 to 9 12 clearances air spaces N S B o over 9 12 to 10 12 T Locking over 10 12 to 11 12 3 25 099 passing through ceilings EN Lugs walls roofs enclosures over 11 12 to 12 12 attic rafter or other nearby JUS TN over 12 12 to 14 12 combustible surfaces 14 12 to 16 12 6 183 Do not pack air spaces 5 Cut a hole in the roof centered on the small 2 with insulation Check drilled hole placed in the roof in Step 2 The over 16 12 to 18 12 Venting Arrangemnt hole should be of sufficient size to meet deem 18 12 to 20 12 7 2 2 Vertical Termination the minimum requirements for clearance to de 2 section for the combustibles of 1 1 2 38mm Slip the flashing maximum vertical rise under the shingles shingles should overlap poor draft or down drafting can result from of the venting system and 2 3 G half the flashi
37. e Heat Shield 11 Lift the heat shield up and pull out slightly to clear the head screws and then hang it on the top bracket located directly above the heat shield close to the top of the firebox Wire Harness Disconnected 12 Disconnect both sources of power the power cord located on the 15 Remove the control box by carefully lifting off the velcro and sliding it left hand side of the firebox and the wires connected to the back up out from the side of the firebox battery located on the right side of the firebox LLI 0 Z lt Z LLI lt lt gt NOTE The control box will need to be flipped as it is being brought out from the side of the firebox Back up Battery shown 40 Regency L676E Direct Vent Gas Fireplace 16 Disconnect the spark cable and valve sensor wires from the control board 17 Remove the 16 screws that hold the valve tray to the firebox and carefully pull out the valve tray Valve Tray 18 Disconnect the black and red wires from the solenoid valve 19 Replace the valve tray and reverse steps to re install Ensure to check the gasket around the valve tray opening 20 Turn on the gas supply and check for gas leaks 21 Plug in the power source 22 Re install the grate 23 Re install the interior brick panels 24 Re install the log set 25 Re install the glass door 26 Check the inlet 12 WC and outlet 10 WC 27 Re in
38. e provisions shall comply with NFPA 720 and be ANSI UL 2034 listed and IAS certified 3 SIGNAGE A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight 8 feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment The sign shall read in print size no less than one half 1 2 inch in size GAS VENT DIRECTLY BELOW KEEP CLEAR OF ALL OBSTRUCTIONS 4 INSPECTION The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless upon inspection the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5 08 2 a 1 through 4 b EXEMPTIONS The following equipment is exempt from 248 CMR 5 08 2 a 1 through 4 1 The equipment listed in Chapter 10 entitled Equipment Not Required To Be Vented in the most current edition of NFPA 54 as adopted by the Board and 2 Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling building or structure used in whole or in part for residential purposes MANUFACTURER REQUIREMENTS GAS EQUIPMENT VENTING SYSTEM PROVIDED When the manufacturer of Product Approved side wall horizontally vented gas equipment provides venting system design or venting system components
39. eBright Paint Metallic Black 6309 4 Make a periodic check of burner for proper position and condition Visually check the flame ofthe burner periodically making sure the flames are steady not lifting or floating If there is a problem call a qualified service person 5 The appliance and venting system must be inspected before use and at least annually by aqualified field service person to ensure that the flow of combustion and ventilation air is not obstructed Note Never operate the appliance without the glass properly secured in place 6 Donotusethis appliance if any parthas been under water Immediately call a qualified service technician to inspect the appliance andtoreplace any partofthe control system and any gas control which has been under water 7 In the event this appliance has been serviced check that the vent air system has been properly resealed amp reinstalled in accordance with the manufacturer s instructions 8 Verify operation after servicing GENERAL VENT MAINTENANCE Conduct an inspection of the venting system semiannually Recommended areas to inspect as follows 1 Check the Venting System for corrosion in areas that are exposed to the elements These will appear as rust spots or streaks and in extreme cases holes These components should be replaced immediately 2 Remove the Cap and shine a flashlight down the Vent Remove any bird nests or other foreign material 3 Che
40. ebox 3 Remove the battery by lifting off the velcro and bring out from the side of the firebox T 21 b Swing the door out from the top and release the hinges on the T left and right side of the door by lifting them up Door lt gt 2 m 2 gt 2 2 nk 3 Loosen the 2 screws that hold the right side heat shield in place Heat Shield 5 Replace with new battery and reconnect battery wires accordingly 6 Re install the battery to the right side of the firebox 7 Re install the right side heat shield Regency L676E Direct Vent Gas Fireplace 37 MAINTENANGE 4 Disconnect both sources of power the power cord located on the 7 Disconnect the spark cable and flame sensor wires from the control left hand side of the firebox and the wires connected to the back up board battery located on the right side of the firebox Back up Battery Power Receptacle 8 Remove the cable tie from control box to release the wires Do not discard cable tie 5 Remove the control box by carefully lifting off the velcro and sliding it out from the side of the firebox NOTE The control box will need to be flipped as it is being brought out from the side of the firebox 9 Remove the ground screw from the side of the control box Do not discard the ground screw LLI 0 Z lt Z LLI lt lt gt 6 Disconnect the wire harnesses from the control board labelled
41. ed location Diagram 2 pipe into the vent cap assembly Itis important Put a bead of high temperature silicone that the vent pipe extends into the vent cap inside the outer section of the adapter and sufficient distance so as to result in a minimum a bead of Mill Pack on the inner collar Slip Note pipe overlap of 1 1 4 inches 32 Secure the adapter over the existing inner and outer a The horizontal run of vent must be level the connection between the vent pipe and flue collar Fasten to the outer collar only with or have 1 4 inch rise for Even 1 foot the vent cap the 3 supplied screws drilling pilot holes will of run towards the termination Never make this easier allow the vent to run downward This 40 Install wall thimble in the center of the 11 could cause high temperatures and may 279mm square and attach with wood screws 4 Levelthe fireplace and fasten it to the framing present the possibility of a fire Diagram 7 using nails or screws through the top and side nailing strips b The location of the horizontal vent 5 Assemble the desired combination of pipe termination on an exterior wall must meet Wood screws and elbows to the appliance adaptor and twist lock for solid connection Note For best results and optimum perfor all local and national building codes and must not be blocked or obstructed See Exterior Vent Termination Locations section for more details gt
42. ed to extend this limited lifetime warranty to the original purchaser of a Regency Product This warranty is not transferable The Warranty Limited Lifetime The combustion chamber heat exchanger burner tubes logs brick panels against defective manufacture only are covered under the Limited Lifetime Warranty for five 5 years for parts and subsidized labour and parts only thereafter Glass is covered for lifetime against thermal breakage only parts and subsidized labour for five 5 years and parts only thereafter from date of purchase Electrical and mechanical components such as switches wiring FPI remote controls pilot assembly components control boards and gas valves are covered for two years parts and one year subsidized labour from the date of purchase Blowers and valves replaced under warranty are considered repairs and continue as if new with appliance ie twelve 12 months from original purchase date of appliance with a minimum of three 3 months coverage from date of replacement FPI venting components are covered parts and subsidized labour for three 3 years from date of purchase Simpson Dura Vent venting components Direct Vent units are covered by Simpson Dura Vent Inc warranty Repair replacement parts purchased by the consumer from FPI after the original coverage has expired on the unit will carry a 90 day warranty valid with a receipt only Any item shown to be defective will be repaired or replaced at our discr
43. ed to provide you with all the warmth and charm of wood fireplace at the flick of a switch The model L676E has been approved by Intertek for both safety and efficiency As it also bears our own mark it promises to provide you with economy comfort and security for many trouble free years to follow Please take a moment now to acquaint yourself with these instructions and the many features of your Regency Fireplace MANUFACTURED MOBILE HOME REQUIREMENTS INFORMATION FOR MOBILE MANUFACTURED HOMES AFTER FIRST SALE This Regency product has been tested and listed by Intertek as a Direct Vent Wall Furnace to the following standards VENTED GAS FIREPLACE HEATERS ANSI Z21 88 2005 CSA 2 33 2005 CAN CGA 2 17 M91 ANSI Z21 50 2003 CSA 2 22 2003 ANSI Z21 50A 2003 CSA 2 22A 2003 ANSI Z21 50B 2003 CSA Z22b 2003 and GAS FIRED APPLIANCES FOR USE AT HIGH ALTITUDES CAN CGA 2 17 M91 This Direct Vent System Appliance must be installed in accordance with the manufacturer s installation instructions and the Manufactured Home Construction and Safety Standard Title 24 CFR Part 3280 or the current Standard of Fire Safety Criteria for Manufactured Home Installations Sites and Communities ANSI NFPA 501A and with CAN CSA Z240 MH Mobile Home Standard in Canada This appliance installation must comply with the manufacturer s installation instructions and local codes if any In the absence of local codes follow the current National Fuel Gas Code ANSI Z223 1 and the
44. emote Control Manual FireWizard E Not available as a replacement part Regency L676E Direct Vent Gas Fireplace Part 30 521 015 31 521 016 32 521 042 35 948 455 36 948 454 37 521 050 40 521 063 41 502 061 42 380 013 43 W840470 46 521 007 521 034 47 521 025 48 910 480 521 574E P 521 576E P 910 952 910 953 904 617 904 622 904 241 904 345 910 937 Description Bracket Log Tray Log Tray Deflector Log Tray Burner Rear NG LP Burner Front NG LP Grate Bracket Log Position Pilot Shield Pilot Holder Gasket Pilot Assembly Valve Tray Valve Tray Gasket Valve Bracket Valve 845 SIT Electric Valve Assembly NG Valve Assembly LP Pilot Assembly NG Pilot Assembly LP NG Orifice 434 NG Orifice 448 LP Orifice 456 LP Orifice 453 Valve Solenoid Regency L676E Direct Vent Gas Fireplace BURNER amp LOG ASSEMBLY PARTS LIST 43 gt 24 NOTES 44 Regency L676E Direct Vent Gas Fireplace NOTES Regency L676E Direct Vent Gas Fireplace 45 NOTES 46 Regency L676E Direct Vent Gas Fireplace WARRANTY FIREPLACE PRODUCTS REGENCY Regency Fireplace Products are designed with reliability and simplicity in mind In addition our internal Quality Assurance Team carefully inspects each unit thoroughly before it leaves our facility FPI Fireplace Products International Ltd is pleas
45. ent restrictor must be at Set 0 for both NG and LP HIN gt gt iil N N NN 27 D V1 total pipe length is 30 feet with min of 11 feet total vertical and max 9 feet total horizontal Please note min 1 foot between 90 elbows is required VENT RESTRICTOR SETTING Vent restrictor must be at Set 0 for both NG and LP 20 Regency L676E Direct Vent Gas Fireplace INSTALLATION Vertical Venting with Two 2 90 Elbows 2 2 gt Em gt Z v1 One 90 e bow Two 45 elbows Option V V Withthese options max total pipe length is 30 feet with min of 6 feet total vertical and max 10 feet total horizontal 6 Min 4 Min 5 Min Please note min 1 foot between 6 Min 90 elbows is required VENT RESTRICTOR SETTING Vent restrictor must be at Set 0 for both NG and LP Vertical Venting with Three 3 90 Elbows One 90 elbow Two 45 elbows With these options max total pipe length is 30 feet with min of 9 feet total vertical and max 8 feet total horizontal Please note min 1 foot between 90 elbows is VENT RESTRICTOR SETTING Vent restrictor must be at Set 0 for both NG and LP Regency L676E Direct Vent Gas Fireplace 21 INSTALLATION VENTING ARRANGEMENTS ALLOWABLE VERTICAL TERMINATIONS
46. er thimble half to the inside wall The thimble halves slip inside each other and can be adjusted for 2 x 4 or 2 x 6 walls Slip the assembled liner and termination assembly through the thimble making sure the termination cap faces up there are markings on the cap that show which way is up This will position the termination cap with proper down slope for draining water Fasten the cap to the outer wall with the 4 supplied screws Pull the centre 5 127mm liner and outer 8 203mm liner out enough to slip over the flue collars of the fireplace You may wish to cut the liner shorter to make it more workable Do not bend liner more than 90 The liners must slip over the collars a minimum of 1 3 8 Apply Mill Pac overthe fireplace inner collar and slip the 5 127mm liner down over it and attach with 3 supplied screws Do the same with the 8 203mm liner Apply a bead ofsilicone between the thimble and termination and around the outer edge of the terminal at the wall in order to keep the water out INSTALLATION IMPORTANT Do not locate termination hood where excessive snow or ice buildup may occur Be sure to check vent termination area after snow falls and clear to prevent accidental blockage of venting system When using snow blowers make sure snow is not directed towards vent termination area 2 2 gt Em gt Z ASTROCAP XL DIMENSIONS 946 623 P 12 1 4 311 12 1 4
47. er to Framing amp Finishing section e Venting Requirements Refer to Venting section 2 Assemble Top Standoffs Refer to Unit Assembly Prior to Installation 3 Install back up battery Refer to Back up Battery Installation section 4 Slide unit into place 5 Install vent Referto Venting Arrangement sections 6 Make gas connections Refer to Gas Line Installation section 7 Make electrical connections Refer to Wiring Diagram section NOTE Unit requires 120V to operate 8 Test the pilot Refer to Pilot Adjustment section 9 Test Gas Pressure Refer to Gas Pipe Pressure Testing section 2 2 gt E gt Z Z e x lt ep Z INSTALLATION 10 Install standard and optional features Refer to the following sections Interior Brick Panels Log Set Exterior Brick Panels Remote Control refer to Matching Remote Handset amp Control Box ID Code section 11 Final check Before leaving this unit with the customer the installer must ensure that the appliance is firing correctly and operation fully explained to customer This includes 1 Clocking the appliance to ensure the correct firing rate rate noted on label 42 000 NG Btu h 40 000 LP Btu h after burning appliance for 15 minutes 2 Ifrequired adjusting the primary airto ensure that the flame does not carbon First allow the unit to burn
48. etion No labor coverage is included with these parts Conditions Any part or parts of this unit which in our judgement show evidence of such defects will be repaired or replaced at FPI s option through an accredited distributor or agent provided that the defective part be returned to the distributor or agent Transportation Prepaid if requested It is the general practice of FPI to charge for larger higher priced replacement parts and issue credit once the replaced component has been returned to FPI and evaluated for manufacturer defect The authorized selling dealer is responsible for all in field service work carried out on your Regency product FPI will not be liable for results or costs of workmanship from unauthorized service persons or dealers At all times FPI reserves the right to inspect product in the field which is claimed to be defective All claims must be submitted to FPI by authorized selling dealers It is essential that all submitted claims provide all of the necessary information including customer name purchase date serial type of unit problem and part or parts requested without this information the warranty will be invalid Exclusions This limited Lifetime Warranty does not extend to or include paint door or glass gasketing or trim At no time will be liable for any consequential damages which exceed the purchase price of the unit has no obligation to enhance or modify any unit once manufactured ie
49. for 15 20 min to stabilize CAUTION Any alteration to the product that causes sooting or carboning that results in damage is not the responsibility of the manufacturer MANUFAGTURED MOBILE HOME ADDITIONAL REQUIREMENTS 1 Ensure that structural members are not cut or weakened during installation 2 Ensure proper grounding using the 8 ground lug provided See Wiring Diagram section LOCATING YOUR GAS FIREPLAGE 1 When selecting a location for your fireplace ensure that the clearances are met 2 The appliance must be installed on a flat solid continuous surface e g wood metal concrete This may be the floor or raised up on platform to enhance its visual impact The appliance must be installed on metal or wood panel extending the full width and depth of the appliance 3 The L676E Direct Vent Gas Fireplace can be installed in a recessed position or framed out into the room as in A B C and D See Diagram 1 Flat on Wall B Flat on Wall Corner Recessed into Wall Alcove Corner Diagram 1 4 This appliance is Listed for bedroom installations using the standard FireWizard Remote Some areas may have further requirements check local codes before installation 5 The L676E Direct Vent Gas Fireplace is approved for alcove installations see Clearances section for details 6 We recommend that you plan your installation on paper using ex
50. ge personal injury or loss of life Improper installation adjustment alteration service or maintenance can cause injury or property damage Refer to the owner s information manual provided with this appliance For assistance or additional information consult a qualified installer service agency or gas supplier A BEFORE LIGHTING smell all around the appliance area for gas Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance Do not touch any electric switch do not use any phone in your building Immediately call your gas supplier from a neighbours phone Follow the gas supplier s instructions If you cannot reach your gas supplier call the fire department B Do not use this appliance if any part has been under water Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water 0117972 30 This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air CAUTION Hot while in operation Do not touch Severe Burns may result Due to high surface temperatures keep children clothing and furniture gasoline and other liquids having flammable vapors away Keep burner and control compartment clean See installation and operating instructions accom
51. he label on the unit and if there is a difference the label on the unit is the correct one For the State of Massachusetts installation and repair must be done by a plumber or gasfitter licensed in the Commonwealth of Massachusetts For the State of Massachusetts flexible connectors shall not exceed 36 inches in length For the State of Massachusetts the appli ances individual manual shut off must be a t handle type valve The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720 and a CO alarm with battery back up in the same room where the gas appliance is installed COPY OF SAFETY DECAL DO NOT REMOVE THIS LABEL NE PAS ENLEVER CETTE TIQUETTE MREGENGY 3 DYET Serial No No de serie Listed VENTED GAS FIREPLACE Tested to ANSI Z21 88 2005 CSA 2 33 2005 2 17 91 VEKTE ANSI Z21 50 2003 CSA 2 22 2003 ANSI Z21 50A 2003 Ge CSA 2 22A 2003 ANSI Z21 50B 2003 CSA Z22b 2003 gh m Certified for Certifi e pour CANADA AND U S A NATURAL GAS FIREPLACE MODEL L676E NG Factory Equipped For Altitude 0 4500ft 0 1372m E 5 2 Min Supply Pressure WC 1 25 kpa m e Low Setting Man Pressure 1 6 WC 0 39 gt 2 Manifold Pressure 3 5 WC 0 87 kpa 8 Orifice Size Front Burner 48 DMS 2 Orifice Size Back Burner H34 DMS Minimum Input 11 000 Btu h 3 22 KW Maximum Input 42 000 Btu h
52. ied for use with Heat Wave Kit 4946 556 and Heat Release Kit 2946 570 Electrical Supply 120 V 0 22 A 60 Hz NOT FOR USE WITH SOLID FUEL Minimum Clearances to Combustibles from Fireplace Side Walls A 15 381mm Ceiling B 52 1320mm Min Mantel Height 16 1 2 419mm Max Mantel Depth 0 13 330mm Alcove Width E 84 2134mm Alcove Depth 36 914mm Non Combustible Hearth Extension Hearth Height 2 51mm Hearth Width 29 1 8 737mm Hearth Depth 12 300mm Alcove side wall must have a min of 15 381mm clearance on one side Mantel depth taken at 26 1 2 673mm from front facing FPI Fireplace Products International Ltd Delta BC CANADA MADE IN CANADA FABRIQUE AU CANADA 918 622 Regency L676E Direct Vent Gas Fireplace REQUIREMENTS MA Code CO Detector for the State of Massachusetts only 5 08 Modifications to NFPA 54 Chapter 10 2 Revise 10 8 3 by adding the following additional requirements a For all side wall horizontally vented gas fueled equipment installed in every dwelling building or structure used in whole or in part for residential purposes including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven 7 feet above finished grade in the area of the venting including but not limited to decks and porches the following requirements shall be satisfied 2 2 gt JEN gt Z
53. ing Systems 16 Basic Horizontal amp Vertical Terminations 16 5 x 8 Rigid Pipe Cross Reference Chart 17 Venting Arrangements 19 Allowable Horizontal Terminations 19 Venting Arrangements 1 22 Allowable Vertical Terminations 22 Unit Installation with Horizontal Termination 23 Unit Installation with Vertical Termination 24 Horizontal Termination with Flex Vent System 25 Regency L676E Direct Vent Gas Fireplace TABLE OF CONTENTS Hion Elevation a 26 Gas Line 1551311811618 aa 26 OE 000 26 Gas Pipe Pressure Testing 26 SIT 845 Valve Description 26 Aeration Adjustment 2 2 26 Back Up Battery Installation 27 Brick Panel Installation 28 Set INStallation xy aha ka nrbe 30 1119012111 32 OPERATING INSTRUCTIONS Gas COMO VANG Lasse EG 33 Matching Remote Handset amp Control Box ID Code 33 Operating Instructions 33 gitur D 33 Lighting Procedure
54. justable Length 11 14 Black Adjustable Length 17 24 Galvanized Adjustable Length 17 24 Black Extension Pipe 8 1 2 Galvanized Extension Pipe 8 1 2 Black Extension Pipe 16 Galvanized Extension Pipe 16 Black 45 Elbow Galvanized 45 Elbow Black 45 Elbow Swivel Galvanized 45 Elbow Swivel Black 90 Elbow Galvanized 90 Elbow Black 90 Elbow Swivel Galvanized 90 Elbow Swivel Black 90 Starter Elbow Swivel Galvanized Adaptor Ceiling Support Cathedral Support Box Wall Support Band Offset Support Wall Thimble Black Wall Thimble Support Box Ceiling Support Firestop Spacer Trim Plate Black L676E Direct Vent Gas Fireplace 58DVA 06 58DVA 06B 58DVA 09 58DVA 09B 58DVA 12 58DVA 12B 58DVA 18 58DVA 18B N A from FPI 58DVA 24 58DVA 24B 58DVA 36 58DVA 36B 58DVA 48 58DVA 48B 58DVA 60 58DVA 60B N A from FPI N A N A Disc See 58DV 08A Disc See 58DV 08AB Disc See 58DV 16A Disc See 58DV 16AB 58DVA 08A N A from FPI 58DVA 08AB 58DVA 16A N A from FPI 58DVA 16AB 58DVA E45 58DVA E45B Disc See 58DVA E45 Disc See 58DVA E45B 58DVA E90 58DVA E90B Disc See 58DVA E90 Disc See 58DVA E90B N A N A 58DVA DC 58DVA CS 58DVA WS 58DVA ES N A from FPI 58DVA WT 58DVA DC N A from FPI 58DVA FS 58DAV WFS Simpson Direct Vent 55 Discontinued 1208 1208B 1207 1207B 1206 1206B 58DVA 18 5
55. l four sides bolt Horizontal lt Top to Vinyl Standoff lt mounting the termination center of hole Install the vent system according to the manufacturer s instructions included with the components j 1 Set the unit in its desired location Check to M NO stander determine if wall studs or roof rafters are in G Wall Thimble the way when the venting system is attached required Diagram 5 If this is the case you may want to adjust the location of the unit Rough in the gas r The fourwood screws provided should be re preferably on the right side of the unit and placed with appropriate fasteners for stucco the electrical junction block is on the left brick concrete or other types of sidings side on the left gt 8 Before connecting the horizontal run of vent 2 Direct Vent pipe and fittings are designed with pipe to the vent termination slide the Wall specialtwist lock connections to connectthe N 2 Thimble over the vent pipe The wall thimble venting system to the appliance flue outlet is required for all horizontal terminations A twist lock appliance adaptor is required m 3 In conjunction with the Simpson Dura Vent v 9 Slide the appliance and vent assembly Direct Vent GS system Install the adaptor towards the wall carefully inserting the vent after the unit is set in its desir
56. le and the control module plugged in for the unit to operate fully The front and rear burners will operate on low when the unit is running on battery back up Do not cut the ground terminal off under any circumstances Lockout Led Reset Button WIRING DIAGRAM Caution Ensure that the wires 00 not touch any hot surfaces and are away from sharp edges Flame Sensor 2 NG LP ECS MODULE jumper 120V Power Source NEUTRAL white 32 park Ignitor MODULATING Q V He EX EMBER SECONDARY BURNER CAUTION Label all wires prior to disconnection when servicing controls Wiring errors can cause improper and dangerous operation REAR 8 MAIN BURNER red black 9V SOLENOID VALVE PILOT Spark Ignitor Flame Sensor mi Regency L676E Direct Vent Gas Fireplace OPERATING INSTRUCTIONS GAS CONTROL VALVE The gas control knob is located on the right hand side of the firebox behind the right side exterior brick panel 1 Remove the right side exterior brick panel Right Side Exterior Brick Panel 2 Loosen the 2 screws that hold the right side heat shield in place 3 Lift the heat shield up and pull out slightly to clear the head screws and then hang it on the top bracket located directly above the heat shield close to the top of the firebox Regency L676E Direct Vent Gas Fireplace MATCHING REMOTE HANDSET amp CONTR
57. may wish to relocate the appliance orto offset as shown in Diagram 2 to avoid cutting load bearing members Note lf an offset is necessary in the attic to avoid obstructions it is important to support the vent pipe every 3 feet 0 9 meter to avoid excessive stress on the elbows and possible separation Wall straps are available for this purpose 2 Galvanized pipe is desirable above the roofline LN 3 AFirestop spacer mustbe installed in the floor or ceiling of every level duetoits highercorrosionresistance Continue to add pipe sections through the flashing until the height of the vent cap meets the minimum height requirements specified in Diagram 5 or local codes Note that for steep roof pitches the vertical height must be increased Offset 7 Height firestop spacer N gt 24 Regency L676E Direct Vent Gas Fireplace UNIT INSTALLATION HORIZONTAL TERMINATION WITH FLEX VENT SYSTEM Note top clearance of 3 76mm and 1 Note 2 3 side amp bottom clearance of 2 51mm must be maintained except when passing through wall ceiling or at the termination where the use of a firestop or wall thimble reduces the required clearance to 1 1 2 38mm Werecommendframinga 11 279mm x 11 279mm inside dimensions hole to give structural rigidity for mounting the termin
58. n will be produced if air shutter is tightly closed Note Any damage due to carboning resulting from improperly setting the aeration controls is NOT covered under warranty 26 Regency L676E Direct Vent Gas Fireplace INSTALLATION BACK UP BATTERY INSTALLATION 1 Unsecure the battery from the outer firebox base flange by cutting the 6 Connect the red and black wires to the battery accordingly cable tie and remove from protective wrapping 2 Remove the plastic pin protectors from the battery 3 Loosen the 2 screws that hold the right side heat shield in place 2 2 gt E gt 4 O Z Note Battery Hookup Ensure that the black wire is connected to the black spade and the red wire is connected to the red spade Heat Shield 7 Place the battery into position at the base of the firebox as shown 4 Lift the heat shield up and pull out slightly to clear the head screws and then hang it on the top bracket located directly above the heat shield close to the top of the firebox 5 Pull out the black and red battery wires from the right side of the firebox 8 Re install the heat shield Regency L676E Direct Vent Gas Fireplace 27 Z lt EM lt op 2 INSTALLATION BRICK PANEL INSTALLATION IMPORTANT Must install 1 set of brick panels The operation of this unit without the brick panels is prohibited Dangerous operating conditions may occur if the panel
59. nds from your gas appliance This is perfectly normal due to the fact that there are various gauges and types of steel used within your appliance Listed below are some examples All are normal operating sounds and should notbe considered as defects in your appliance Burner Tray The burner tray is positioned directly under the burner tube and logs and is made of a different gauge material from the rest of the firebox and body Therefore the varying thicknesses of steel will expand and contract at slightly different rates which can cause ticking and cracking sounds You should also be aware that as there are temperature changes within the unit these sounds will likely re occur Again this is normal for steel fireboxes Pilot Flame While the pilot flame is on it can make a very slight whisper sound Gas Control Valve As the gas control valve turns ON and OFF a dull clicking sound may be audible this is normal operation of a gas regulator or valve Unit Body Firebox Different types and thicknesses of steel will expand and contract at different rates resulting in some cracking and ticking sounds will be heard throughout the cycling process OPERATION DURING POWER OUTAGE Inthe event of a power failure the unit will be fully functional for approximately the first 45 minutes using the backup battery system If power resumes within the first 45 minutes you can continue using the unit as normal If power is re
60. ng as per Diagram 4 high wind conditions nearbigtrees oradjoining the maximum horizontal roof lines in these cases increasing the vent offset limitations height may solve the problem Diagram 1 2 Setthe gas appliance inits desired location Drop plumb bob down from the ceiling to the position of the plumber s appliance flue exit tape and mark the location connected where the vent will to wall strap penetrate the ceiling 7 Ensure vent is vertical and secure the base of the flashing to the roof with roofing rails slide storm collar over the pipe section and seal with a mastic 8 Install the vertical termination by twist locking it Note Anyclosets or storage spaces which Drill a small hole at wa I 45 the vent passes through must be his point Next drop Strap Elbows enclos d a plumb bob from Diagram 4 The upper half of the flashing is the roof to the hole 4 installed under the roofing material and not Offset Chart previously drilled in 1 SFirestop nailed down until the chimney is installed the ceiling and mark Spacer This allows for small adjustments GS 8 203 seg m the spot where the Diagram 2 vent will penetrate the roof Determine if ceiling Offset Pipe Length L Height joists roofrafters or other framing will obstruct 9 Continue to assemble pipe lengths inches mm inches mm inches the venting system You
61. not clean when the glass is hot Theuse of substitute glass will void all product warranties Care must be taken to avoid breakage of the glass Do not strike or abuse the glass Do not operate this fireplace without the glass front or with a cracked or broken glass front Wear gloves when removing damaged or broken glass Replacement of the glass panel s should be done by a licensed or qualified service per son GLASS REPLACEMENT In the event that you break your glass by impact purchase your replacement from an authorized Regency dealer only Replacement glass is shipped already installed into the door frame CAUTION Wear gloves when removing damaged or broken glass WARNING Do not operate the appliance with the glass panels removed cracked or broken Replacement of the glass panels should be done by a licensed or qualified service person 36 Regency L676E Direct Vent Gas Fireplace BACK UP BATTERY REPLACEMENT CONTROL BOX REPLAGEMENT 1 Loosen the 2 screws that hold the right side heat shield in place 1 Remove the exterior brick panels 2 Remove the glass door a Release the 2 door latches on the left and right side at the top of the firebox Heat Shield Latch 2 Lift the heat shield up and pull out slightly to clear the head screws and then hang it on the top bracket located directly above the heat shield close to the top of the fir
62. panying appliance LIGHTING INSTRUCTIONS STOP Read the safety information above on this label Plug the power cord into a power outlet Press and release the ON OFF button once on the Remote Control After approximately 3 seconds the spark ignition system will spark for 30 seconds to light the main burner If the main burner does not light within 90 seconds you must reset the unit See instruction manual for details TO TURN OFF GAS APPLIANCE Press the ON OFF button once on the Remote Control If service is to be performed you must disconnect both sources of power to the unit main power and the battery DO NOT REMOVE THIS INSTRUCTION PLATE 18628 Regency L676E Direct Vent Gas Fireplace 35 Lu O 2 lt 2 Z lt 2 MAINTENANGE MAINTENANGE INSTRUCTIONS 1 Always turn offthe gas valve before cleaning For relighting refer to lighting instructions Keep the burner and control compartment clean by brushing and vacuuming at least once a year When cleaning the logs use a soft clean paint brush as the logs are fragile and easily damaged 2 Clean appliance and door with a damp cloth never when unit is hot Never use an abrasive cleaner The glass should be cleaned with a gas fireplace glass cleaner The glass should be cleaned when it starts looking cloudy 3 The heater is finished in a heat resistant paintand should only be refinished with heat resistant paint uses Stov
63. ressure tap s turning counterclockwise with a 1 8 wide flat screwdriver 3 Attach manometer to IN and or OUT pressure tap s using a 5 16 ID hose 4 Turn the unit ON 5 The pressure check should be carried out with the unit burning and the setting should be within the limits specified on the safety label 6 When finished reading manometer turn off the unit disconnect the hose and tighten the screw clockwise with a 1 8 flat screwdriver Note Screw should be snug but do not over tighten SIT 845 VALVE DESCRIPTION 1 On Off Solenoid Valve EV1 2 On Off Solenoid Valve EV2 3 Inlet Pressure Test Point 4 Outlet Pressure Test Point 5 Connection for Pressure Regulator Combustion Chamber Compensation 6 Pressure Regulator for Minimum and Maximum Outlet Pressure 7 Gas Outlet Pressure Electric Modulator 8 Pilot Outlet 9 Main Gas Outlet 10 Side Outlet 11 Main Gas Inlet 11 AERATION ADJUSTMENT The burner aeration is factory set but may need adjusting due to either the local gas supply or altitude Open the air shutter for a blue flame or close for a more yellow flame In order to adjust the aeration the logs grate and burners will need to be removed to be able to access the shutters Minimum Air Shutter Opening NG Front Burner 1 4 Rear Burner 1 8 LP Front Burner 5 16 Rear Burner 1 4 CAUTION Carbo
64. results in damage to the interior exterior facia is not the responsibility of FPI Subsidy according to job scale as predetermined by FPI Regency L676E Direct Vent Gas Fireplace 47 fireplaces are designed with reliability and simplicity in mind In addition our internal Quality Assurance Team carefully inspects each unit thoroughly before it leaves our door FPI Fireplace Products International Ltd is pleasedto extend this Limited Lifetime Warranty to the original purchaser of a FPI Product See the inside back cover for details Register your Regency online at http www regency fire com oW T gt H TONER LL NW i Installer Please complete the following information Dealer Name amp Address Installer Phone Date Installed Serial No egency Liberty AstroCap HeatWave Heat Release and FireWizard are trademarks of FPI Fir Copyright 2008 FPI Fireplace Products International Ltd All rights reserved
65. s are broken Handle with care DO NOT FORCE INTO POSITION Interior Brick Panel Installation 3 Remove the 2 brick panel clips on the inside left and right side of the firebox by removing the screw 1 Remove the glass door a Release the 2 door latches on the left and right side at the top of the firebox F Latch 4 Place the 2 small back brick panels at the base of the firebox on the left and right side of the rear log tray b Swing the door out from the top and release the hinges on the left NOI TOEIC en and right side of the door by lifting them up Left Side Back Brick Panel Right Side Back Brick Panel Hinge Door Place the door soft surface to prevent scratching 2 Unwrap the brick panels from the protective wrapping Note The logs must not be in the unit Right Side Back Brick Panel Left Side 28 Regency L676E Direct Vent Gas Fireplace INSTALLATION 5 Install the back brick panel by carefully placing it against the back 7 Slide the left side brick panel into position and secure in place with wall of the firebox the brick panel clip that was removed in step 3 2 2 gt Em gt 4 Z Exterior Brick Panel Installation 1 Ensure installation of the logs and glass door has been completed before installing the exterior brick panels 2 Line up the pins in the exterior base brick panel with the holes on the outerbox of the firebo
66. s for copper lines and flex connectors are usually considered to meet this requirement Important Always check for gas leaks witha soap and water solution or gas leak detector Do not use open flame for leak testing PILOT ADJUSTMENT Periodically check the pilot flames Correct flame pattern has three strong blue flames 1 flowing around the pilot 1 flowing around the flame sensor and 1 flowing across the burner it does not have to be touching the burner Burner 0 O O O O O O O O O O O O O O O O O O O Flame Sensor Pilot Ignitor Note Ifyou have anincorrect flame pattern contact your Regency dealer for further instructions Incorrect flame pattern will have small probably yellow flames not coming into proper contact with the rear burner or flame sensor GAS PIPE PRESSURE TESTING The appliance must be isolated from the gas supply piping system by closing its individual manual shut off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1 2 psig 3 45 kPa Disconnect piping from valve at pressures over 1 2 psig The manifold pressure is controlled by aregulator builtinto the gas control and should be checked at the pressure test point Note Toproperly check gas pressure both inlet and manifold pressures should be checked using the valve pressure ports on the valve 1 Make sure the unit is turned OFF 2 Loosen the IN and or OUT p
67. stall the right heat shield 28 Check operation of flame control 29 Check for proper flame appearance 30 Re install the exterior brick panels lt gt 2 m 2 gt 2 2 2 L676E Direct Vent Gas Fireplace 41 00 as a PARTS LIST Part 1 521 527 2 502 008 5 904 751 6 W260280 7 770 066F 8 942 117 9 W260260 11 521 528 12 521 540 940 351 P 13 521 013 15 521 079 16 910 950 910 075 17 521 075 20 521 901 521 902 521 930 521 935 946 556 946 570 521 969E 918 621 910 960 918 619 MAIN ASSEMBLY Description Flue Collar Inner Assembly Flue Collar Outer Cap Screws 1 4 x 4 1 2 1 But Gasket Top Relief Plate Top Relief Plate Top Relief Frame Top Relief Frame Gasket S Base Brick Panel Door Frame Assembly with Glass Glass gt 5 lt 2 12 One Piece Faceplate i gt 6 Valve Heat Shield A gt 7 Control Box with Igniter amp Battery Backup Backup Battery lt lt 2 8 Outer Control Box Cover 2 9 gt Brick Panel Set Standard Brown Brick Panel Set Standard Red Left Side Panel Interior Top Panel Interior Back Panel Interior Right Side Panel Interior Right Side Panel Exterior Base Panel Exterior Left Side Panel Exterior Birch Log Set Oak Log Set Heat Wave Kit Heat Release Kit LP Conversion Kit Manual FireWizard R
68. stored after 45 minutes you will need to reset the unit as follows a Remove the left side exterior brick panel b Hold the reset button for 3 to 5 seconds or until the LED stops blinking c Press and release the ON OFF button once on the Remote Control Reset Button Located on the left hand side of the firebox behind the exterior brick panel BACKUP BATTERY Listed below are approved battery types that can be used for replacement a Powersonic 1 3AH b Panasonic 1 3AH c Henda 1 3AH d Magnacharge 1 3AH CAUTION Risk of Energy Hazard 12V 1 3 Amphere hour battery Before replacing batteries remove con ductive jewelry such as chains wrist watches and rings High energy through conductive materials could cause severe burns Dispose of batteries at an authorized battery disposal site Do not dispose of batteries in fire The batteries may explode Do not open or mutilate batteries Released material is harmful to the skin and eyes It may be toxic Regency L676E Direct Vent Gas Fireplace OPERATING INSTRUCTIONS COPY OF LIGHTING PLATE INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTING This appliance must be installed in accordance with local codes if any if none follow the National Fuel Gas Code ANSI Z223 1 NFPA 54 or Natural Gas and Propane Installation Codes CSA B149 1 WARNING If you do not follow these instructions exactly fire or explosion may result causing property dama
69. the glass door will no longer open properly Non combustible wall board is installed up to the flanges on all sides of the unit When installing any additional facing material use the Finishing Template included with the unit to ensure that the finishing material does not exceed the allowable overlap The Finishing Template uses two magnets to attach itself to the flange on the left or right side of the unit see diagram below Install the facing material up to the outside edge when facing the unit of the finishing template This template may be discarded after the facing material has been installed Regency L676E Direct Vent Gas Fireplace INSTALLATION need to use heated room air for combustion and losing warm room air up the chimney VENTING To set the vent restriction as indicated in the Screws for plugging the holes venting arrangements diagrams refer to the all holes must be plugged with a screw INTRODUCTION instructions below e Screw holes for fixing the restrictor plate The L676E uses the balanced flue technology 1 Remove the glass door Axial system The inner liner vents products Release the 2 door latches on the left of combustion to the outside while the outer and right side at the top of the firebox gt liner draws outside combustion air into the combustion chamber thereby eliminating the gt O 2 Note These flue pipes must not be connected to any other appliance
70. tly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings Only permitted if veranda porch deck or balcony is fully open on a minimum of two sides beneath the floor If the vent termination is accessible a certified guard shall be installed As specified in CGA B149 Installation Code Note Local codes or regulations may require different clearances n accordance with the current ANSI Z223 1 NFPA 54 Natioinal Fuel Gas Code 14 Regency L676E Direct Vent Gas Fireplace INSTALLATION VENTING ARRANGEMENTS HORIZONTAL TERMINATION FLEX Regency Direct Vent System These venting systems in combination with the L676E have been tested and listed as a direct vent heater system by Intertek The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram from the Exterior Vent Termination Locations section 2 2 gt Em gt Z FPI Direct Vent Flex System Termination Kits include all the parts needed to install the L676E using a flexible vent 1 946 618 6 Feet 8 flexible liner Kit length 5 flexible liner Kit length spring spacers 3 thimble 2 AstroCap termination cap 1 UMM 946 616 10 Feet screws 12 tube of Mill Pac 1 plated screws 8 S S screws 8 x 1 1 2 drill point 4 10 vinyl siding standoff Vinyl Siding standoff Wall Thimble SG
71. tor Setting NG Factory Set on Set 0 4 LP Factory Set on Set 1 n 72 1829mm Minimum Height 2 Requirement a 8 I TERI v VENT RESTRICTOR SETTING NG Units Vent restrictor at Set 0 factory set no adjustment required unless otherwise indicated LP Units Vent restrictor at Set 1 factory set no adjustment required unless otherwise indicated Refer to the Vent Restrictor Position section for details on how to change the vent restrictor to Set 1 Set 2 or Set 3 if required A vent guard maybe required as per local codes refer to Exterior Vent Termination Requirements section for details Note Regency Direct Vent System Flex is only approved for horizontal terminations Maintain clearances to combustibles as listed in Clearances section Horizontal vent must be supported every 3 feet e Firestops are required at each floor level and whenever passing through a wall e A wall thimble is mandatory for all horizontal terminations due to high temperatures Regency L676E Direct Vent Gas Fireplace 19 2 2 gt E gt Z INSTALLATION Horizontal Venting with Two 2 90 Elbows Z e x lt ep Z One 90 elbow Two 45 elbows pipe length is 30 feet with minimum of 6 feet total vertical and maximum 8 feet total horizontal es Please note minimum 1 foot between 90 elbows is required VENT RESTRICTOR SETTING V
72. x and fit in place 6 Place the top brick panel into position and hold it in place while slid ing the right side brick panel into position and secure using the brick panel clip that was removed in step 3 Outerbox of Firebox 3 Install the right side exterior brick panel by placing the bottom tab into the slot of the exterior base brick panel The top of the brick panel is held in place by magnet that sits against the bracket as shown in the image below Repeat for left side exterior brick panel Bracket Brick Panel Clip a Tab Base Brick Panel Slot Regency L676E Direct Vent Gas Fireplace 29 Z lt EM lt op 2 INSTALLATION LOG SET INSTALLATION Installation of Interior Brick Panels must be completed before installing the log set Read the instructions below carefully and refer to the diagrams 3 Place log 03 27 on the front left side of the burner Place the right If the logs are broken do not use the unit until they are replaced end of the log into the pin and rest the left end of the log inbetween Broken logs can interfere with pilot operation the rear and front burner tubes Log kit Part No 521 930 and 521 935 contain the following pieces a 03 25 Log Rear b 03 26 Log Top c 03 27 Log Front Left d 03 28 Log Front Right 902 154 Embers Lava f 902 179 Vermiculite 0 946 669 Platinum Embers supplied with packaged manual Rear B Burner

Regency LIBERTY L676E-NG User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents