Regalo 1158 User's Manual
Contents
1. 0 You may also write us at Regalo International Inc 14198 Commerce Ave N E Suite 600 Prior Lake MN 55372 Madein China EF comand l M Important Keep these e O instructions for future reference Widespan Gate Model 1158 This gate can be used in openings from 29 inches to 58 inches Assembly and Installation Instructions Contact Regalo for questions and replacem ent Please read these instructions carefully b efore parts Ifin doubt the use of your gate call our installing your gate customer care line at 952 440 1950 The safety of your child is your responsibility Regalo International Inc 14198 Commerce Ave N E Suite 600 Prior Lake MN 55372 Made in China Check that you have these contents 1 Gate Frame sp A WARNING Intended for young children aged six months through 24 months Check the gate regularly to seeif all the hardware and mountings are tightened To prevent serious injury or death securely install gate or enclosure and use according to manufacturer s instructions Never use with a child adle to climb over or dislodge the gate or enclosure Never leave child unattended Use only with the locking latching mechanism securely engaged Note I fusing this gate at the top of stairs the 4 wall Cups MUST beused Ifnot used the gate could be dislodged from the opening 2 Hardware Pack which should contain 4 Threaded Spindle Rods ssc 4 Adjustable Wheel Spindles o alr2. Gate Extension Instructions cy O Widespan Gate Model 1158 Please follow these instructions carefully to ensure that your gate extension is properly installed Improp er installation could resultin the gate becoming dislodged from the doorway or unstable Always make sure the extension is securely attached to the gate before using The safety of your child is your responsibility Note Ifusing this gate at the top of stairs the 4 Wall Cups MUST beused Ifnot used thegate could be dislodged from the opening Instructions for Gate Extension Hilf EI Latham ES 1 Assemble the gate per the gate instructions t Choose the side of the gate to be extended and remove the top and bottom Adjustment Wheel Spindles 3 Assemble the gate and extension as illustrated 4 Reposition the gate and fitin accordance with the gate fitting instructions Important Keep these instructions for future reference Itis preferable to install the extension on the hinge side of the gate If you have an application that requires additional extensions please contact the retailer which you purchased your gate from We offer the following sizes of extensions for your gate 4 inch 6inch 12inch and 24 inch They are available at most retailers that carry our Regalo Products line of metal gates For questions regarding your gate or replacement parts contact our customer care department at 952 440 195
3. Model 1158 Step 3 Positioning and Attaching the Wall Cups to your door opening Your gate is a pressure mounted gate Therefore it is not necessary to use the screw attached Wall Cups to your door opening if you choose not to However IF YOU ARE USING THE GATE AT THE TOP OF STAIRS YOU MUST USE THE WALL CUPS Regardless of whether you are using your gate at the top of stairs or not using the Wall Cups will affix your gate more firmly in the doorway So you may choose to use them in all applications If you choose not to use the Wall Cups you may skip to Step 4 now Before attaching your Wall Cups to your doorway opening you must make sure you have the screw holes marked correctly It is important to install the gate with a spacing of not more than 3 from the floor To do this simply position your gate in the doorway so that it is level and centered as shown in Diagram C 1 Then place the Wall Cups over the flat end of the Threaded Spindle Rods which should already be fully inserted into the ends of the gate frame tubes as shown in Diagram C 2 Pull the Threaded Rods out until the Flat end with the Wall Cup is against the wall Pull all four Threaded Spindle Rods outin this manner Then take a pencil and make a light mark on the wall around the parameter of the Wall Cups Once you have marked the correct spots on your walls you can move the gate aside Next you will need to mark the Screw Holes To this simply take a Wall Cup and center it
4. eady assembled to the Spindle Threaded Rods 4 Wall Cups 6 4 Screws tH 3 Three Extensions 12 Extension 6 Extension 4 Extension 1 i Important Keep these g O instructions for future reference Widespan Gate Model 1158 Assembling and Installing Your Gate Note IMPORTANT you will notice a slight Gap between the gate door latch and the frame tube THIS IS NOT A DEFECT Your gate is a pressure mounted gate and this gap will disappear once you tighten your gate in the doorway Step 1 Begin by locating the 4 Threaded Spindle Rods Before you begin turn the Adjustment Wheels clockwise until they are almost against the flat end of the Threaded Spindle Rods WARNING The Adjustment Wheel should NOT touch the flat end of the Thread Spindle Rod If it does it might get stuck Diagram A Step 2 You are going to insert the 4 Threaded Spindle Rods into the holes in the 4 ends of the gate frame as shown in Diagram B1 IMPORTANT THE ENDS OF THE GATE FRAME ARE NOT THREADED THE THREADED SPINDLE ROD SHOULD SLIDE INTO THE END OF THE FRAME TUBES WITHOUT ANY RESISTENCE Push the Threaded Spindle Rods all the way into the frame tube until the Adjustment Wheel hits the end of the frame tube as shown in Diagram B2 Diagram B 1 Diagram B2 Adjustment Wheel E FA of the Frame Tube 2 Important Keep these C O instructions for future reference Widespan Gate
5. ls a few too many turns To correct this simply turn the upper Adjustment wheels clockwise a few turns until you havea 1 16 inch gap Your gate is now ready to use Diagram F Threaded Spindle Rod OE mi Flat Plastic End Z i A diustment Wheel Frame Tube pa g gF rd 1 m a 2 rreri y i gt S N a J TM Important Keep these og instructions for future reference Widespan Gate Model 1158 REMOVINGYOUR GATE FROM THE WALL To remove your gate from the wall begin by turning the Adjustment Wheels clockwise mtil the flat plastic ends ofthe Threaded Spindle Rods come out from the Wall Cups This will free your gate from the wall CARE AND MAINTENANCE Periodically check the gate for sign of damage wear or for missing components Do not useif any partis missing worn or damaged components Check the gate regnlarly to make sure all the hardware and mountings are tightened Donotuse abrasive cleaners or bleach Cleanit by sponging with warm water and mild detergent
6. on each pencil circle you marked on your wall Use a pencil to mark the small Screw Hole in the center of the Wall Cup You are now ready to fasten your Wall Cups to the Wall using the self tapping screws included in the hardware packet i Wall Cup a je 3 RO Important Keep these eg instructions for future reference Widespan Gate Model 1158 Step 4 You are now ready to install your gate in the doorway Begin by positioning your gate level and centered in the doorway opening Pull the 4 Threaded Spindle Rods out of the ends of the frame Tubes until the Flat Plastic End touches the wall If you are using the Wall Cups then the flat plastic ends of the Threaded Spindle Rods should go into the Wall Cups that are fastened to your wall Next while holding the flat plastic ends of the Threaded Spindle Rods against the wall turn the Adjustment Wheels counter clockwise until the Adjustment Wheels are up against the ends of the frame tubes as shown in Diagram D DO NOT TIGHTEN Goto Step 5for Final Adjustment HELPFUL HINT It may be necessary to hold the Threaded Spindle Rod while turning the Adjustment Wheel to ensure the Threaded Spindle Rod does not turn Diagram D Adjustment W heel 4 Important Keep these eg instructions for future reference Widespan Gate Model 1158 Step 5 You are now ready to do the Final Adjustment to fasten your gate firmly in the doorwa
7. y Start by turning the BOTTOM Adjustment Wheels FIRST Continue to turn the lower Adjustment Wheels counter clockwise until the Adjustment Wheels are firmly against the ends of the frame tubes IMPORTANT There should be equal space on each side of the gate To easily determine this look at the length of threaded rod is that is showing on each side If the gate is centered there will be an equal length of threaded rod showing If more threaded rod is showing on one side you can adjust this using the Adjustment Wheels Simply turn the side that has too much Threaded Rod showing clockwise and then turn the other side counter clockwise As you so this you will see the sides equaling out as shown in Diagram E Diagram E i Important Keep these eg O instructions for future reference Widespan Gate Model 1158 Next tighten the top 2 Adjustment Wheels by turning them counter clockwise Again make sure both sides are equal as you tighten As you tighten the Adjustment wheels you will notice the gap between the plastic gate door latch and the frame tube is narrowing As the gap continues to narrow continue turning the upper Adjustment Wheels until the frame tube engages in the slot in the plastic gate door handle Leave a 1 16 gap between the frame tube and the plastic gate door latch as shown in Diagram F IMPORTANT The frame tube MUST NOT touch the Plastic gate door latch If it does touch you have turned the Adjustment Whee
Download Pdf Manuals
Related Search