Quantum DAT320 Drive Quick Start Guide
Contents
1. 8 wa A NAD USB cable to server s external USB Port ZA Power cable Server s power supply Th Sete drive Power cable Securing the Drive Note The server latches and side views of your server model may not be exactly the same as shown in the illustrations Please refer also to your server documentation ee Installing the Internal DAT 320 Tape Drive in Your Server Mounting Hardware Used 1 Figure 6 Securing Drive No Mounting Hardware Used 2 Use M3 screws Check that the holes in the chassis are aligned with the holes in the sides of the drive and use a regular Phillips screwdriver to secure the M3 screws see Figure 6 p lt M3 screws supplied with tape drive Ensure blanking plates are in place over empty bays and replace the cover on the server Completing Your To complete and test your internal tape drive installation Installation 1 Use the screws you removed earlier to secure the drive in place a uu A WUN Replace the computer cover Reconnect the power cord to the computer s power connector Turn on the computer If necessary install the DAT320 O S driver Install your backup software program The documentation that came with your software should describe this procedure Gently insert a tape cartridge into the internal tape drive s slot Slide the cartridge into the slot until the drive accepts the cart2. DAT 320 Quick Start Guide Before Installing the DAT 320 Tape Drive in Your System Avoiding Electrostatic Damage Preinstallation Requirements Unpacking and Inspecting the Drive N Your internal tape drive has very sensitive components that are prone to damage from electrostatic discharge ESD Use extreme care when handling the drive as it can be damaged by ESD Before handling the drive read the ESD instructions that follow to prevent damage to the drive Wear an ESD preventive grounding wrist strap or observe similar ESD precautions when working with the drive Be sure the wrist strap makes good skin contact Do not remove the wrist strap until you finish working with the drive Before you remove the drive from the antistatic bag touch a metal or grounded surface to discharge any static electricity buildup from your body Avoid contact between the drive other equipment and clothing The wrist strap only protects the equipment from ESD voltages on the body ESD voltages on clothing can still cause damage When the drive is not being used keep it in its antistatic bag Hold the drive by its edges only Avoid touching any exposed parts on the printed circuit board Always place the drive on top of or inside the antistatic bag to reduce the chance of ESD damage In addition to the contents included with your internal tape drive you need the following items to install your internal tape drive
3. pin USB Type B cable is provided with the tape drive see Figure 3 Installing the Internal DAT 320 Tape Drive in Your Server To an External USB 2 0 Port Purchase a special USB cable and Cable Routing Kit The Cable Routing Kit consists of a bracket with attached cable on one side that connects to the server s external port and a Type A USB socket on the other side Make sure you orientate the bracket correctly when you fit it see Figure 4 1 Remove a spare blanking plate from the rear panel of the server 2 Fit the bracket with attached the cable and fix it to the server Make sure the cable is outside of the server and connect it to the server s external USB port see Figure 4 3 Attach the standard USB cable to the bracket type A connector see Figure 4 Figure 4 Connecting the USB Cable Type B connector to tape drive Type A connector on oe inside of bracket Type A connector to server s external USB port Attaching the Power Note The drive is not powered from the USB bus It must be connected to the server s and USB Cables to the power supply Tape Drive 1 Attach the USB cable to the tape drive Type B connector Installing the Internal DAT 320 Tape Drive in Your Server DAT 320 Quick Start Guide 2 Attach a spare cable from the server s internal power supply to the power connector see Figure 5 Figure 5 Attaching the Power Cable
4. that requires mounting rails fasten the rails to the tape drive e Some servers have snap on mounting rails attached to the filler panel These can be removed and attached to the tape drive with screws To install the tape drive 1 Slide the tape drive into the open bay aligning the tray or rails with the slots in the bay see Figure 2 il HM ih i ii ill If your server does not use mounting hardware check that the holes in the chassis are aligned with the holes in the side of the tape drive Do not secure the drive at this point because you may have to move the drive to get the cables into place Installing the Internal DAT 320 Tape Drive in Your Server 5 Attaching the USB Cable Connecting the USB Cable from the Tape Drive to the Server Figure 3 Connecting to an Internal USB Port DAT 320 Quick Start Guide Decide Which Cable to Use There are several options for connecting the tape drive to your server Toan Use Notes Internal standard standard May be connected to the server s system board or USB port USB cable an internal USB card External USB port standard Cable routing kit is required USB cable To an Internal USB 2 0 Port 1 Use the schematic on the inside of the server panel to check whether your server has an internal USB 2 0 port and locate its position 2 Use the appropriate cable to connect to the server e A standard 5
5. will receive the latest information about your drive as well as other product service and support information For your convenience you can register your drive through our Web site e Please visit www quantum com registration to register your product Safety Compliances The DAT 320 Tape Drives are safety compliant with the following regulatory organizations and codes in the countries indicated Country Regulatory Organization Compliant to US CANADA Underwriters Laboratories UL UL CSA 60950 01 or Canadian Standards 2nd Ed Association CSA EU member nations Comit Europ en de EN 60950 1 Normalisation 2006 A11 2009 Electrotechnique the European Committee for Electrotechnical Standardization CENELEC Registering Your Tape Drive 11 DAT 320 Quick Start Guide Country Regulatory Organization Compliant to IECEE member nations IECEE International Electrotechnical Commission on Electrical Equipment IECEE for Mutual Recognition of Test Certificates for Electrical Equipment CB Scheme CB Scheme per IEC 60950 01 2nd Ed with details and exceptions for each member country Taiwan BSMI BSMI certification CNS 14336 IECEE member nations include Austria Australia Belgium Brazil Canada China PR Czech Republic Denmark Finland France Germany Hungary Ireland Israel Italy Japan Netherlands Norway Poland Singapore Slovakia Sl
6. A USB 2 0 port 5 25 inch half height bay for internal drive Backup application software that supports the internal tape drive For a list of the latest backup software applications tested with the internal DAT 320 tape drives please visit our Web site at http www quantum com ServiceandSupport Index aspx Before you unpack the contents of your drive package inspect the shipping containers for damage If you spot damage to the container notify your carrier immediately When you unpack the package compare the items received with those on the packing list If any item is missing or damaged please contact your place of purchase immediately Before Installing the DAT 320 Tape Drive in Your System Required Tools The following is a list of the tools you will need You may need additional items depending on your installation requirements e Flat blade Phillips or TORX screwdriver depending on the type of screws used by your computer Installing the Internal DAT 320 Tape Drive in Your Server Installing the internal DAT 320 tape drive consists of the following major steps e Preparing Mounting Bay e Attaching Mounting Hardware e Installing the Tape Drive e Attaching the USB Cable e Connecting the USB Cable from the Tape Drive to the Server e Attaching the Power and USB Cables to the Tape Drive e Securing the Drive Preparing Mounting Caution To avoid personal injury or dam
7. Quantum DAT 320 DAT 320 Tape Drive Quick Start Guide Quantum DAT 320 models CD320UH Internal and CD320UE Tabletop are the most reliable DAT drives on the market delivering reliability features to extend media life Figure 1 Internal Drive n Tape Drive Encrypt Before Installing the DAT 320 Tape Drive in Your System eienen 2 Avoiding Electrostatic Damage 2 Preinstallation Requirements 2 Unpacking and Inspecting the Drive 2 Required loolSs 2c ccccrscereevetscssssceesenrs 3 Installing the Internal DAT 320 Tape Drive in YOUNES NVGligc iss scstececererartetisvscaesstccseses 3 Preparing Mounting Bay 3 Attaching Mounting Hardware 3 Installing the Tape Drive 5 Attaching the USB Cable 6 Connecting the USB Cable from the Tape Drive to the Server 008 6 Attaching the Power and USB Cables to the Tape Drive eee e ea ee 7 Securing the Drive 8 Completing Your Installation 9 Installing the Tabletop DAT 320 Tape Drive to Your System s sessessssssesessrrrrrrrrrrrrrenee 10 Connecting the Power and USB Cables to Your Tabletop Drive 10 Completing Your Installation 10 Safety Compliances ceeceeeee 11 Electromagnetic Compatibility EMC Gomplian es cAciisessesieescsccerectieesstesass 12 www quantum com
8. age to the server or tape drive ensure that Bay the server is disconnected from the main power supply while you install the drive 1 Assemble the necessary tools and materials e Phillips screwdriver 2 Perform a normal system shutdown and turn off the server and any connected peripherals 3 Remove the cover and front panel from the server as detailed in your server s documentation As you work inside the server you may have to disconnect other signal cables or power cables from other devices to maneuver the new drive into place If you have to do this make a note of their position and connections so you can put them back correctly later 4 You are now ready to install your tape drive Attaching Mounting If your server requires special rails or other hardware to install the tape drive mount Hardware them on the tape drive now If your server does not require special mounting hardware proceed to Installing the Tape Drive Installing the Internal DAT 320 Tape Drive in Your Server 3 DAT 320 Quick Start Guide Caution Static electricity can damage electronic components Always wear an antistatic wrist strap if one is available If not after you have disconnected power from the server and removed the cover touch a bare metal part of the chassis Similarly touch a bare metal part of the drive before installing it Note If mounting hardware is supplied with your tape drive it may not be exactly
9. he USB connector on the server Note It is important to ensure that you connect your drive to a USB 2 0 port The drive will work on a USB 1 1 port but performance will be severely degraded Completing Your To complete and test your tabletop tape drive installation Installation 1 Use the On Off Switch on the back of the tabletop tape drive to turn on the drive see Figure 7 The Ready LED should be ON the other three front panel LEDs should be OFF 10 Installing the Tabletop DAT 320 Tape Drive to Your System 2 Turn on the computer 3 If necessary install the DAT320 O S driver 4 Install your backup software program The documentation that came with your software should describe this procedure 5 Gently insert a tape cartridge into the tabletop tape drive s slot Slide the cartridge into the slot until the drive accepts the cartridge and loads it A brief delay occurs while the drive identifies the cartridge type and state and moves the tape to the data area Then the green Ready LED goes ON 6 Use your backup software application to perform a sample backup and verify operation The green Ready LED flashes as data is written to and or read from the tape 7 At the end of the operation press the Eject button on the front of the tabletop tape drive to eject the cartridge from the drive Registering Your Tape Drive After you install the tape drive be sure to register it Registering your drive ensures that you
10. ma tilkoples jordet stikkontakt Dette produktet kan tilkobles et IT stram distribusjonssystem F r kunder i Sverige Apparaten skall anslutas till jordat uttag Note Use these drives only in equipment where the combination has been determined to be suitable by an appropriate certification organization for example Underwriters Laboratories Inc or the Canadian Standards Association in North America You should also consider the following safety points e Install the drive in an enclosure that limits the user s access to live parts gives adequate system stability and provides the necessary grounding for the drive e Provide the correct voltages 5 VDC and 12 VDC based on the regulation applied Extra Low Voltage SEC for UL and CSA and Safety Extra Low Voltage for BSI and VDE if applicable Electromagnetic Compatibility EMC Compliances DAT 320 Quick Start Guide 14 For assistance contact the Quantum Customer Support Center USA EMEA APAC Worldwide Quantum Preserving the World s Most Important Data Yours 2010 Quantum Corporation All rights reserved Quantum the Quantum logo and all other logos are registered trademarks of Quantum Corporation or of their respective owners Protected by Pending and Issued U S and Foreign Patents including U S Patent No 5 990 810 ANETTA N 6 66928 01 Rev B September 2010 About Quantum Quantum Corp NYSE QTM is the leading global storage com
11. ovenia Spain Switzerland United Kingdom and USA Jotta asiakasta Suomessa Laite on liitettava suojakosketinpistorasiaan For kunder i Norge Apparatet ma tilkoples jordet stikkontakt Dette produktet kan tilkobles et IT stram distribusjonssystem F r kunder i Sverige Apparaten skall anslutas till jordat uttag Electromagnetic Compatibility EMC Compliances The DAT 320 Tape Drives are EMC compliant with the following regulatory organizations and codes in the countries indicated Country Regulatory Organization Compliant to Australia New Zealand Australian Communications and Media Authority ACMA AS NZA 3548 same as CISPR 22 Canada Industry Canada Digital Apparatus Interference Causing Equipment Standard ICES 003 ICES 003 Digital Apparatus EU member nations CE Emissions per CISPR 22 EN55022 and Immunity per CISPR 24 EN55024 Japan 12 Voluntary Control Council for Interface VCCI VCCI Electromagnetic Compatibility EMC Compliances Country Regulatory Organization Compliant to Taiwan Bureau of Commodity Inspection and Quarantine BSMI BSMI EMC certification CNS 13438 United States Federal Communications Commission FCC Title 47 Code of Federal Regulations Part 15 Subpart B 47CFR15B Jotta asiakasta Suomessa Laite on liitettava suojakosketinpistorasiaan For kunder i Norge Apparatet
12. pany specializing in backup recovery and archive Combining focused expertise customer driven innovation and platform independence Quantum provides a comprehensive range of disk tape media and software solutions supported by a world class sales and service organization This includes the DXi Series the first disk backup solutions to extend the power of data deduplication and replication across the distributed enterprise As a long standing and trusted partner the company works closely with a broad network of resellers OEMs and other suppliers to meet customers evolving data protection needs
13. ridge and loads it A brief delay occurs while the drive identifies the cartridge type and state and moves the tape to the data area Then the green Ready LED goes ON Use your backup software application to perform a sample backup and verify operation The Ready green LED flashes as data is written to and or read from the tape At the end of the operation press the Eject button on the front of the internal tape drive to eject the cartridge from the drive Installing the Internal DAT 320 Tape Drive in Your Server 9 DAT 320 Quick Start Guide Installing the Tabletop DAT 320 Tape Drive to Your System Installing the tabletop DAT 320 tape drive consists of the following major steps e Connecting the Power and USB Cables to Your Tabletop Drive e Completing Your Installation Connecting the Power Note The drive is not powered from the USB bus It must be connected to the main and USB Cables to Your power supply Tabletop Drive A power cable is provided with your Quantum DAT 320 tape drive 1 Make sure that the drive is switched OFF O side down The power switch is on the rear panel 2 Connect the USB cable to the USB connector on the back of the enclosure 3 Plug the power cable securely into the socket on the rear panel of the drive and plug the other end of the power cable into the power outlet Figure 7 Connecting Power and USB Cables On off switch Power cable USB cable 4 Plug the USB cable into t
14. the same as shown in the illustrations Different models of server require different mounting methods The server may also incorporate a locking mechanism to hold the tape drive in place Please check your server documentation to ascertain the correct method of mounting and to check whether mounting hardware is provided with the server Mounting Rails Some servers require mounting rails These may be metal or plastic rails attached to the filler panel of the server s drive bay 1 Use a regular Phillips screwdriver to attach the appropriate rails Use M3 screws 5 mm 0 2 in Ensure you have the M3 screws The rails may be attached to the filler panel by screws of a different thread size type and these should not be used If in doubt refer to your server documentation Mounting Screws Other server models only require the use of special locating screws with no mounting rail 1 Use a screwdriver to attach the appropriate screws You may need to purchase the M3 screws separately Position the screws see Figure 1 Figure 1 Attaching Mounting Screws 4 Installing the Internal DAT 320 Tape Drive in Your Server Installing the Tape Drive Figure 2 Installing the Tape Drive 2 Attach the appropriate mounting hardware Refer to the manufacturer s documentation for instructions e If you are installing on a server that requires a tray place the tape drive in the tray e If you are installing in a server
Download Pdf Manuals
Related Search