Q-See QCA7201B Technical Manual
Contents
1. building has excessive static The camera will need to be seperated from the metal building by using a rubber gasket If a cable run exceeds 200ft we recommend using the RG 59 cables shown in the right two columns of this table which are available through www Q SeeStore com Longer cable runs will require a stronger power supply or for the power supply to be closer to Video quality is always enhanced by using shielded cables To prevent video signal loss run one continuous cable between the camera and DVR for best results If more length is required use the minimum number of inter connection points possible WARNING Always check state and local laws before installing cameras and cables 2011 NEC 820 44 Trademarks All brand names and products are trademarks or registered trademarks of their respective owners Q See is a registered trademark of DPS Inc Disclaimer The information in this document is subject to change without notice The manufacturer makes no representations or warranties either express or implied of any kind with respect to completeness of its contents Manufacture shall not be liable for any damages whatsoever from misuse of this product DISPOSAL If the camera no longer functions or can no longer be repaired it must be disposed of according to regulations regarding electronic waste By not disposing of electronic items in household waste you will not only be following the law but contri2. glow from the LEDs Check camera on known functioning cable to determine if issue lies with camera or cable Cable extended to more than 60 feet and no video or video only during the day The camera power supply power splitter combination is only designed to power cameras up to 60 feet Any cameras beyond that distance will need their own power supply which is available at www Q SeeStore com Dark video image Some cameras feature an infrared cut filter to improve daytime video images This can sometimes become stuck Place a hand over the lens for 10 seconds to trigger night vision mode You may hear a soft click as the filter resets Upside down video image Change the orientation or position of your camera to correct Or use the video flip option in your DVR s Camera Settings menu Camera looking through window has video image during day but not at night The LEDs on the camera act as a flashlight and at night this light is being reflected by the window back at the camera You will need to reposition the camera outside the window Camera video is very dark during one time of day but lighter during others The camera may be positioned so that the sun shines directly into it This will backlight the subjects in the camera s field of view and cause them to appear dark and washed out Reposition the camera to avoid this keeping in mind that the sun will change positions over the course of a year as well as during the day Camera on metal
3. placed in more exposed locations if needed Outdoor cameras are designed to operate between 20 F to 140 F 28 C to 60 with a relative humidity of up to 95 and consider wind chill and other environmental factors when selecting your location TO CONNECT TO A SECURITY DVR SYSTEM STEP 1 STEP 3 STEP 4 Connect the BNC connector on the other end of the power and video cable to a Video In port on the back of the DVR AUDIO IN o VIDEO IN Plug the power splitter cable into the camera power adapter DO NOT plug the adapter into an outlet at this time Connect the BNC and power leads from the camera to the matching connectors on one end of the power and video cable CAMERA a g O Bi soos If you have a multi IMPORTANT When connecting the power and video cable between the camera and the DVR the male power end red plug Aa package the included a power adapter is designed to connects to the matching power lead on the camera When selecting a surge protector is STRONGLY recommended to use one that is UL 1449 rated for a clamping voltage of 330 or lower a Joule rating of at least 400 and a response time of 10 nanoseconds or less Repeat Steps 1 through 4 for all cameras before continuing STEP 5 Plug the power adapter into a surge protector STEP 2 For multi camera packs connect the power connector on the other end of the cable to the power splitter For singl
4. when submerged in water Ensure that all power and video connections are not directly exposed to water and are protected from the elements Indoor cameras should not be used outdoors Even if they are in a sheltered location they can still suffer damage due to humidity dust and other environmental factors Mounting surface The mounting surface must be sturdy and able to hold at least five times the camera s total weight Legal Considerations Always check state and local laws before installing cameras 2011 NEC 820 44 Do not place camera behind a window If there is a light source behind the camera it can cause a reflection in the window that will obscure events on the other side of the glass Likewise the camera s infrared LEDs will reflect off the glass and shine into the lens thus degrading the image Light levels should be approximately the same between camera and target area A camera in a brightly lit area looking into a shaded area or vice versa may produce inadequate results The above are guidelines and the optimal location for your camera will depend on your unique circumstances As a general rule the locations highlighted in Green in the picture to the right indicate the best locations to mount your camera Both locations are sheltered from rain or snow and offer good sight lines to allow your camera to monitor a wide area Because your camera is weatherproof it requires less protection than weather resistant cameras and it can be
5. SOCS simplicity quality technology User Manual AnalogHD Cameras AnalogHD cameras will only function when connected to an AnalogHD DVR If you are upgrading from a standard Analog system you will be able to use the existing BNC power video cable but you must to replace both the recorder and the cameras with AnalogHD technology equipment WHERE TO LOCATE THE CAMERA When installing your camera it is important to select a proper site not only for field of view but for other considerations as well Distance from viewing recording device The further the camera is from the DVR or monitor the higher the chances of signal degradation Typical 7592 Video Cable provides acceptable signal at distances up to 200 60m At greater distances UL Listed shielded RG59 should be used The camera s power supply should be located as near to the camera as possible when the distance exceeds 200 as the power level will drop over extended distances resulting in a decrease in video quality Do not place near high voltage wires or other sources of electrical interference Electrical interference will degrade the quality of the signal Place camera out of reach to avoid damage Avoid direct exposure to weather You should not place the camera where rain or snow will hit the lens directly nor should the camera be placed so that the sun or bright light shines directly into the lens Your camera is weatherproof but it will not work
6. buting to the protection of the environment Digital Peripheral Solutions Inc 8015 E Crystal Dr Anaheim CA 92807 www q see com Q See Customer Support USA FAQ videos guides 24 7 amp live chat M F 6am 7pm Sat amp Sun 9am 5pm PST at www Q See com Support
7. e camera packages connect the power lead into the power adapter itself In this case you can skip to Step 4 m e e provide enough voltage to operate multiple cameras Connecting a single camera to the adapter can cause the optical chipset of that camera to burn out and become useless EXTENSION CABLES For more information on which cable to use for your application please see the extended chart at www q see com cableselection To purchase order online at www Q SeeStore com Q See Model Number Maximum Run Length 1650 1650 750 Video Cable RG 59 RG 50 Usage Indoor Outdoor Do not run inside Indoor Outdoor In wall or along wall walls or underground PRECAUTIONS CAUTION Risk of electrical shock To prevent electric shock do not remove screws or cover Do not attempt to disassemble camera There are no user serviceable parts inside Service should be performed by a qualified Q See technician only Handle camera with care Do not hit shake puncture or drop the camera as this could cause damage and prevent proper operation Avoid strong light Do not aim camera at sun or aim strong light directly into the lens as it will degrade image quality and could cause damage Camera should ideally be placed out of direct sunlight for improved performance Protect from elements indoor outdoor cameras are weatherproof but direct exposure to excessive rain sun or marine environmental conditions will degrade
8. their performance and shorten the life of the product Indoor only cameras should NEVER be used outdoors Even if sheltered from direct exposure they will still be damaged by dust and moisture in the air Avoid excessive moisture within camera or ad adapters Do not use strong or abrasive detergents when cleaning camera body Clean with dry cloth or mild detergent wiping gently Do not use camera beyond prescribed voltage range Only use included power supply Ensure power input source conforms to local voltage Voltage outside of range could cause damage or abnormal performance QS50B 50 QS100B 100 QSVRG60 60 QSVRG100 100 QSVRG200 200 QS59500 500 QS591000 1000 Other Notes the camera To maintain video quality FREQUENTLY ASKED QUESTIONS Below are some frequently asked questions regarding cameras Additional information plus live chat during regular business hours can be found at www Q See com Support Lines in the video images Check the cable If you connect a camera that is working to the cable of the camera that has the lines and it too shows lines replace the cable If you are in an area with a lot of electrical interference switch to a shielded cable such as RG 59 No video from camera Check all connections and make sure that camera is connected to proper power supply Check to see that the camera is receiving power by cupping hand over lens You should see a faint red
Download Pdf Manuals
Related Search