ProForm (No.PFMC99100) User's Manual
Contents
1. 2 Locate the loose Pulse Wire C inside the Console Base E Connect the Pulse Wire to the wire on the Receiver D Next peel the paper off the pad on the bottom of the Receiver D Turn the Receiver so the small cylinder is on the side shown and press the Receiver into the bottom of the Console Base E in the location indicated by the dotted line Note The two included jumper wires can be discarded The Wire Tie can be used to tie wires if needed Make sure that no wires are pinched See step 1 Reattach the Console Back B with the Screws A How to Use the Heart Rate Monitor The unique heart rate monitor is specially designed for accuracy comfort and durability To get the best per formance from the heart rate monitor please read the instructions below HOW TO PUT ON THE HEART RATE MONITOR The heart rate monitor consists of two components the chest strap and the sensor unit Follow the steps below to put on the heart rate monitor Sensor Unit 1 Refer to the inset drawing above Insert the tab on one end of the chest strap through one end of the sensor unit as shown Make sure to press the end of the sensor unit under the buckle on the chest strap 2 Wrap the heart rate monitor around your chest Attach the other end of the chest strap to the sensor unit as described above Adjust the length of the chest strap if necessary The heart rate monitor should be under your clothing against your2. The included Long Jumper Wire can be dis carded The Wire Tie can be used to tie wires if needed Make sure that no wires are pinched See step 1 Reattach the Console Back B with the Screws A 1 Make sure that the power cord is unplugged Rernove the indicated Screws A from the Console Back B Remove the Console Back from the Console Base C 2 Have a second person hold the Console Base C as you remove the indicated Screws D from the Console Base 3 Connect the Long Jumper Wire E to the PULSE jack on the back of the Console F If there is a wire already plugged into the PULSE jack unplug it Feed the Long Jumper Wire through the hole in the side of the Console Base C 4 Connect the Long Jumper Wire E to the wire on the Receiver G Next peel the paper off the pad on the back of the Receiver Turn the Receiver so the cylinder is on the side shown and press the Receiver onto the back of the Console Base C in the indicated location Note The included Short Jumper Wire can be discarcied The Wire Tie can be used to tie wires if needed Make sure that no wires are pinched See steps 2 and 1 Reattach the Console F and the Console Back B Note If you have a PROFORM 785Pi or model number PFTL79100 please call 1 800 999 3756 1 Make sure that the power cord is unplugged Remove the indicated Screws A from the Console Back B Remove the Console Back from the Console Base E
3. heart rate readings the user must be within arm s length of the console The heart rate monitor is designed to work with peo ple who have normal heart rhythms Heart rate read ing problems may be caused by medical conditions such as premature ventricular contractions pvcs tachycardia bursts and arrhythmia The operation of the heart rate monitor can be af fected by magnetic interference caused by high power lines or other sources If it is suspected that magnetic interference may be causing a problem try relocating the treadmill If the heart rate monitor still does not function prop erly test the heart rate monitor in the following way Hold the heart rate monitor and place your thumbs over the electrode areas as shown Electrode Areas ed ext hold the heart rate monitor near the console While holding one thumb stationary begin tapping the other thumb against the electrode area at a rate of about one tap per second Check the heart rate reading on the console If the heart rate monitor does not function properly after you have followed all of the above instructions the battery should be replaced in the following way Locate the battery cover on the back of the sensor unit Insert a coin into the slot in the cover turn the cover counterclock wise and remove the cover Remove the old bat tery and insert a new CR 2032 battery Make sure that the battery is turned so the writing is on t
4. or advise you how to ship the product for service Before shipping always obtain a Return Authorization Number RA No from our Customer Service Department securely pack your product save the original shipping carton if possible put the RA No on the outside of the carton and in sure the product Include a letter explaining the prob lem and a copy of your proof of purchase if you be lieve the service is covered by warranty ICON is not responsible or liable for indirect special or consequential damages arising out of or in con nection with the use or performance of the product or damages with respect to any economic loss loss of property loss of revenues or profits loss of enjoy ment or use costs of removal installation or other consequential damages of whatsoever nature Some states do not allow the exclusion or limitation of inci dental or consequential damages Accordingly the above limitation may not apply to you The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein Some states do not allow limitations on how tong an implied warranty lasts Accordingly the above limitation may not apply to you No one is authorized to change modify or extend the terms of this limited warranty This warranty gives you specific legal rights and you may have other
5. Model No Heart Rate Monitor Users Guide OOO PFMC99499 Congratulations for purchasing the new AccuRate heart rate monitor To instali and use the heart rate monitor read and follow all instructions in this user s guide For detailed instructions about using the heart rate monitor with your treadmill refer to the user s manual included with your treadmill This device complies with Part 15 of the FCC rules Operation is subject to the following conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received includ ing interference that may cause undesired operation Changes or modifications not expressly approved by ICON Health amp Fitness Inc could void the user s authority to operate this device How to Install the Receiver Before the heart rate monitor can be used the included receiver must be installed Find the name of your tread mill in the grey boxes on pages 1 to 5 and install the receiver as described If you do not find the name of your treadmill choose the instructions that most closely resemble your treadmill Note Your treadmill may not look exactly like the treadmills shown in the drawings 1 Make sure that the power cord is unplugged Remove the indicated Screws from the Console Back A Important The Screws may be different lengths Keep track of which Screws were removed from which holes 2 Peel the paper off the pad on the bottom
6. ke sure that the power cord is unplugged Remove the indicated Screws A from the Console Back B Remove the Console Back from the Console Base C 2 Connect the Long Jumper Wire D to the wire on the Receiver E Feed the Long Jumper Wire through the holes with the other wires as shown Connect the other end of the Long Jumper Wire to the PULSE jack on the back of the Console F If there is a wire already plugged into the PULSE jack unplug it Turn the Receiver so the cylinder is on the side shown and press the Receiver onto the back of the Console Base C in the indicated lo cation Note The included Short Jumper Wire can be dis carded The Wire Tie can be used to tie wires if needed Make sure that no wires are pinched See step 1 Reattach the Console Back B Purse Jac A Cylinder 1 Make sure that the power cord is unplugged Remove the indicated Screws A from the Console Back B Remove the Console Back from the Console Base E 2 Connect the Short Jumper Wire C to the wire on the Receiver D Connect the other end of the Short Jumper Wire to the PULSE jack on the back of the Console see drawing 2b If there is a wire already plugged into the PULSE jack unplug it Next peel the paper off the pad on the back of the Receiver D Turn the Receiver so the cylinder is on the side shown and press the Receiver into the bottom of the Console Base B in the indicated lo cation Note
7. of the Receiver B Turn the Receiver so the cylinder is on the side shown and press the Receiver into the bottom of the Console Base C in the indicated location 3 Connect the Short Jumper Wire D to the wire on the Receiver B Connect the other end of the Short Jumper Wire to the PULSE jack on the back of the Console C If there is a wire already plugged into the PULSE jack un plug it Note The included Long Jumper Wire can be dis carded The Wire Tie can be used to tie wires if needed Make sure that no wires are pinched See step 1 Reattach the Console C with the 1 Screws 1 3 4 Screws and 2 Screws Important If the Screws are not put back into the same holes that they were removed from the Console will be damaged 1 Make sure that the power cord is unplugged Remove the indicated Screws A from the Console Back B 2 Peel the paper off the pad on the bottom of the Receiver C Turn the Receiver so the cylinder is on the side shown and press the Receiver into the bottom of the Console Back B in the indicated location Connect the Short Jumper Wire D to the wire on the Receiver C Connect the other end of the Short Jumper Wire to the PULSE jack on the back of the Console E Note The included Long Jumper Wire can be discarded The Wire Tie can be used to tie wires if needed Make sure that no wires are pinched See step 1 Reattach the Console Base E with the Screws A 1 Ma
8. op Replace the battery cover and turn it clockwise to close it CR 2032 HEART RATE MONITOR CARE Thoroughly dry the heart rate monitor after each use The heart rate monitor is activated when the electrode areas are wetted and the heart rate moni tor is put on the heart rate monitor shuts off when it is removed and the electrode areas are dried If the heart rate monitor is not dried after each use it may remain activated longer than necessary draining the battery prematurely Store the heart rate monitor in a warm dry place Do not store the heart rate monitor in a plastic bag or other container that may trap moisture Do not expose the heart rate monitor to direct sunlight for extended periods of time Do not expose the heart rate monitor to temperatures above 122 Fahrenheit 50 Celsius or below 14 Fahrenheit 10 Celsius Do not excessively bend or stretch the sensor unit when using orstoring the heart rate monitor Clean the sensor unit using a damp cloth never use alcohol abrasives or chemicals The chest strap may be hand washed and air dried Limited Warranty WHAT IS COVERED The HEART RATE MONI TOR product is warranted to be free of all defects in material and workmanship WHO IS COVERED The original purchaser or any person receiving the product as a gift from the origi _ nal purchaser HOW LONG IS IT COVERED ICON Health amp Fitness Inc ICON warrants the p
9. rights which vary from state to state ICON Health amp Fitness Inc 1500 S 1000 W Logan UT 84321 Printed in USA 2001 ICON Health amp Fitness Inc
10. roduct for one year after the date of purchase WHAT WE DO TO CORRECT COVERED DE FECTS We will ship to you without charge any re placement part or component or at our option we will replace the product WHAT IS NOT COVERED Any failures or damage caused by unauthorized service misuse accident negligence improper assembly or installation alter ations modifications without our written authorization or by failure on your part to use operate and main tain as set out in this manual manual This war ranty does not extend to products used for commer cial or rental purposes or to products used as store display models WHAT YOU MUST DO Always retain proof of pur chase such as your bill of sale store operate and maintain the product as specified in the manual no tify our Customer Service Department of any defect within 10 days after discovery of the defect as in structed return any defected part for replacement or if necessary the entire product for repair MANUAL It is VERY IMPORTANT THAT YOU READ THIS MANUAL before using the product Remember to follow the instructions specified in this manual to assure proper operation and your_contin _ _ ued satisfaction Part No 170688 RO201A HOW TO GET PARTS AND SERVICE Simply call our Customer Service Department at 1 800 999 3756 and tell them your name and address and the model number of your product They will tell you how to get a part replaced
11. skin and as high under the pectoral muscles or breasts as is comfortable Make sure that the logo is facing forward and is right side up 3 Pull the sensor unit away from your body a few inches and locate the two elec trode areas on the inner side Using a saline solu Electrode Areas e e tion such as saliva or contact lens solution wet both electrode areas Return the sensor unit to a position against your chest HEART RATE MONITOR TROUBLE SHOOTING If the heart rate monitor does not function properly or if the displayed heart rate is excessively high or low try the trouble shooting steps beiow e Make sure that the heart rate monitor is under your clothing against your skin and as high under the pectoral muscles or breasts as is comfortable Note if the heart rate monitor does not function when posi fioned_as described try moving it slightly iower or higher on your chest Make sure that the logo on the sensor unit is facing forward and is right side up Each time you use the heart rate monitor use saline solution such as saliva or contact lens solution to wet the two electrode areas on the sensor unit see the drawing below If heart rate readings do not appear until you begin perspiring re wet the electrode areas As you walk or run on the treadmill make sure that you are near the center of the walking belt and within arm s length of the console For the console to dis play
Download Pdf Manuals
Related Search