Polaroid SprintScan 45 User's Manual
Contents
1. Table of contents Quick Scanning Guide Introduction System requirements 1 3 Technical Support 1 4 Registration card 1 4 Unpacking 1 5 Setup and use The scanner and accessories 2 1 Positioning the scanner 2 3 SCSI guidelines 2 3 SCSI ID numbers 2 5 Installing a SCSI adapter in a PC 2 6 Connecting the scanner to your computer 2 6 Diagrams of various SCSI configurations 2 8 Turning on the scanner 2 9 Using the film carriers 2 10 Inserting the carrier into the scanner 2 14 Removing the carrier 2 14 3 Care and maintenance M aintenance 3 1 Troubleshooting 3 2 Limited O ne Y ear Equipment Warranty 3 3 Service 3 3 Polaroid Offices and Service Centers 3 4 Radio and television interference 3 6 Appendix A Specifications A 1 Index l 1 Copyright 1996 Polaroid Corporation All rights reserved See page 2 6 2 5 2 6 Quick Scanning Guide Use this guide as a quick reference for scanning For details see the pages indicated Install a SCSI host adapter card in your computer PC compatibles only Change the SCSI ID number of the scanner if necessary The factory setting is 5 With all equipment turned off connect the scanner to your computer using the SCSI cable provided If the scanner is the last device in the chain use a terminator at the scanner Plug the power cable into the scanner and into a grounded power outlet Turn on the scanner then your computer Install the softw2. ON YOUR SYSTEM Each device on a SCSI chain must have a unique SCSI ID number from 0 to 6 The Apple M acintosh always uses SCSI ID number 7 TheM acintosh internal hard drive usually uses SCSI ID number 0 or 1 The SprintScan 45 scanner is set at the factory to SCSI ID number 5 If this number con flicts with your hard drive or any other device on your SCSI chain you must change either the SCSI ID number of the scanner or the SCSI ID number of the other device Valid SCSI ID numbers are from 0 to 6 The scanner is shipped with the SCSI ID number set to 5 To changetheID number do the following Turn the scanner off and disconnect it from your computer and all other SCSI devices Locate the SCSI ID switch on the back of the scanner picture 1 Pressing the button marked or above and below the switch change the number to an ID number that is unique from other numbers in the chain from 0 to 6 The new number will take effect the next time the scanner is turned on WARNING IF TWO DEVICESON A SCSI CHAIN HAVE THE SAM E SCSI ID NUMBER NEITHER WILL WORK CORRECTLY AND DATA MAY BE DAMAGED WHEN YOU TURN ON THE DEVICES O ID Setup and use 2 5 Installing a SCSI adapter in a PC If you are using a PC compatible computer you must have a SCSI host adapter installed in your computer for connection to the scanner We recommend an Adaptec SCSI host adapter Before connection be sure the settings are correct check
3. call 1 800 268 6970 Wecan help you determine what is at fault and advise you on how and where to get service in the quickest and most convenient way Please contact your nearest Polaroid dealer see the section immediately following Care and maintenance 3 3 Polaroid Offices and Service Centers Massachusetts Polaroid Corporation Tel Toll free 1 800 432 5355 Australia Polaroid Australia Pty Ltd 13 15 Lyonpark Road PO Box 163 North Ryde NSW 2113 Tel 02 950 7000 Fax 02 887 2209 Belgique Belgi Polaroid Belgium S A N V rue Colonel Bourg 111 Kolonel Bourgstraat 111 1140 Bruxelles 1140 Brussel Tel 32 2 726 97 00 Fax 32 2 726 92 99 Toll free line 32 2 78 155 905 Brasil Polaroid do Brasil Ltda Av Paulista 1776 112 andar Cerqueira Cesar S o Paulo Capital 01310 921 Tel 55 11 285 6411 Fax 55 11 283 2625 288 6521 287 5393 Canada Polaroid Canada Inc 350 Carlingview Drive Rexdale ON M9W 5G6 Toll free 1 800 268 6970 Danmark Polaroid a s Blokken 75 Postboks 9 3460 Birker d TIL 42 81 75 00 Fax 42 81 70 26 Deutschland Polaroid GmbH Sprendlinger Landstrasse 109 63069 Offenbach Tel 069 8404 444 069 8404 999 Espa a Polaroid Espa a S A Paseo de la Castellana 130 72 Plta 28046 M adrid Tno 34 1 411 38 36 Fax 34 1 411 40 73 France Polaroid France S A B P 47 78391 Bois d Arcy C dex Tel 1 30 85 60 60 Great Brit
4. 4 Change the SCSI address of the scanner if necessary by press ing the button marked or above and below the switch see page 2 5 for details Setup and use 2 7 Diagrams of various SCSI configurations Scanner is the only SCSI device Scanner and another SCSI device which is internally terminated The following diagrams illustrate different configurations Find the appropriate configuration for your hardware and follow the connection diagram and instructions Note Theshorter the SCSI chain the better it will work Use SCSI cables that are only as long as necessary The chain may not exceed 19 1 2 ft 6m total JE pine mu Termin atar HI HE C mputgr SEanngt The hard disk of the computer is internally terminated Therefore you need to add the terminator to the scanner Place the terminator between the SCSI cable and the scanner Use the SCSI cable provided au u EO S HIRE GE HINE Compu tr Other SCS device kunmi natn Place the terminated device at the end of the chain and do not add any additional terminators If any other external device has an internal terminator the terminator will have to be removed according to the manufacturer s directions Use only approved SCSI cables Scanner and another ap JE RU Termin ater unterminated device HIME HIME IRE z me et Ge Comp HEE ther SOFI device Senn E LIVRES nateg Place the scanner at the end of the chain and use the termina tor
5. 5 scanner captures images at 12 bits per color channel and converts that image data into 24 bit color images with over 16 million colors It features multiple scan ning modes error detection and self diagnostic capability 1 1 Scanning modes The digitized images can contain up to 4000 dpi dots per inch of image information Color is achieved with a tri color CCD in combination with a cold cathode fluorescent light source Two modes are available e 8 bit mode Each dot can be represented by an 8 bit RGB code per color resulting in 256 levels of gray or 16 7 million colors The original is scanned at 12 bits per channel and the results are optimized to 8 bits per channel to producea 24 bit RGB image e 12 bit mode Each dot can be represented by a 12 bit code per color resulting in 4096 levels of gray or 68 7 billion RGB colors System requirements Macintosh systems PC systems s A Macintosh Quadra or PowerPC computer e System 7 1 or higher is required System 7 5 is recommended s 16M B of RAM is required 32M B or moreof RAM is recom mended s An 8 bit or better color monitor is required a 24 bit color monitor is recommended s At least 20M B of free hard disk space is required a 2GB hard disk is recommended e A removable storage device is recommended e Microsoft Windows 3 1 DOS 5 0 or higher or Windows 95 operating systems A PC with a 386SX 25M H z or better microprocessor is require
6. TL C TUV FCC Class B CE Operating temperature 50 to 1040F 10 to 40 C Storage temperature 14 to 140 F 10 to 60 C Relative humidity 20 to 80 A Accessories 2 2 Acoustic noise A 2 Adaptec SCSI host adapter 2 6 Adapter for 35mm slide 1 5 2 2 2 13 Adapters for 120 film 1 5 2 2 2 12 Adobe Photoshop 1 1 B Brightness 1 1 A 1 C Carrier access door 2 1 2 14 Carrier see also Film carriers insertion 2 14 removal 2 14 CD Writer 1 3 Cleaning procedure 3 1 Color images 24 bit 1 1 1 2 Color monitor requirement 1 3 Connection 2 6 2 9 Contrast 1 2 A 1 D Dimensions A 2 dpi dots per inch 1 2 Index E 8 bit gray mode 1 1 F Fan 2 2 FCC notice 3 6 Film carrier slot 2 1 Film carriers 1 5 2 2 for 4x5 film 1 5 2 2 2 10 2 11 four slide film carrier 1 5 2 2 2 10 Film formats 1 1 4x5 film 2 11 4x5 film carrier see Film carriers Fuse replacement 3 1 3 2 H Help 1 4 H umiditiy A 2 Image sensor A 1 L Lamp replacement 3 1 3 2 M M acintosh system requirements 1 3 M aintenance 3 1 P Pass through terminator 1 5 2 7 PC system requirements 1 3 Plug in module 1 1 Polaroid Offices and Service C enters 3 4 3 5 Positioning the scanner 2 3 Power cable 1 5 connector 2 2 consumption A 2 indicator light 2 9 3 2 switch 2 2 2 9 Power R eady lights 2 1 Powerbook 2 4 Powering up 2 9 Q Quick scanning guide iii R Radi
7. The scan will resume when the door is closed but the quality of the scan may be reduced Scan again with the door closed for best scanning quality 4 Initiate the scan from your software The software will prompt you when the scan is finished Removing the carrier 1 When the scan is complete open the door and remove the carrier Remove the film and store it properly to protect it from dust and fingerprints 2 Close the carrier access door The door should be kept closed at all times to protect the mechanism from dust 2 14 3 Care and maintenance Maintenance Keep the carrier access door closed when the scanner is not in use to protect it from dust Cleaning the cabinet Clean with a mild detergent solution Keep the sponge or cloth barely moist Do not let moisture inside the scanner Lamp and fuse The lamp and fuse inside the Sprintscan 45 scanner are not replacement user serviceable If they require replacement the scanner must be returned to a designated service location call Polaroid Technical Support for information on returning your scanner Thelamp should be replaced if the READY indicator fails to come on Warning N othing inside the scanner is user serviceable Do not attempt to disassemble the scanner To do so could result in severe electrical shock and damage to the scanner This action may also void your warranty Contact Polaroid T echnical Support or your authorized repair facility if the scanner is mal
8. ain Polaroid U K Ltd W heathampstead H ouse Codicote Road W heathampstead Hertfordshire AL4 8SF Freefone 0800 010119 Hong Kong Polaroid Far East Ltd 32 F Windsor H ouse 311 Gloucester Road Causeway Bay Tel 852 2894 0333 Fax 852 2895 1382 Italia Polaroid Italia S p A Via Piave 11 21051 Arcisate V arese Tel 0332 470031 Fax 0332 478249 34 J apan N ippon Polaroid Kabushiki Kaisha M ori Building No 30 2 2 Toranomon 3 chome M inato ku Tokyo 105 Tel 81 3 3438 8811 Toll free 0120 248716 M xico Polaroid de M xico S A deC V Paseo dela Reforma 195 Piso 14 C P 06500 M xico D F Tel 703 1111 Fax 566 0505 Del interior al 91 800 70 727 Ventas 91 800 70 747 Nederland Polaroid N ederland B V Zonnebaan 45 3606 CH M aarssen PO Box 1219 3600 BE M aarssen Tel 31 30 410 420 Fax 31 30 411 969 R eparaties Polaroid Europa B V H oge Bothofstraat 45 7511 ZA Enschede New Zealand Polaroid N ew Zealand Ltd Camera Services 24 26 Anzac Avenue Auckland Tel 09 377 3773 Norge Polaroid N orge A S Industriveien 8B Postboks 80 1471 Sk rer Tif 67 90 47 10 Fax 67 90 51 73 sterreich Polaroid Ges m b H Eitnergasse 5A 1231 Wien Tel 869 86 27 Fax 869 81 00 Portugal Polaroid Espa a S A Sucursal em Portugal Edificio Monumental Avenida Praia da Vit ria 71 A 49 B 1050 Lisboa Tel 01 316 10 52 Puerto Ri
9. are according to the software manual To scan an image place the transparency or negative in one of the carriers using an adapter for formats smaller than 4x5 inches Lift the carrier access door and insert the loaded carrier into the front slot Initiate the scan from the software see the software manual When the scan is complete pull out the carrier Remove the original transparency or negative and store it properly Quick Scanning Guide iii 1 Introduction The Polaroid SprintScan 45 multi format film scanner allows you to capture and convert film images into electronic files that you can edit and incorporate into your documents and presentations T he scanner can be connected to a M acintosh computer or an IBM compatible computer with a SCSI host adapter installed see page 2 6 For M acintosh users the SprintScan 45 is shipped with a soft ware plug in that allows you to acquireimages in any Adobe PhotoShop plug in compliant application then edit and print them from within the application For users of the Windows operating system the SprintScan 45 is shipped with a M icro soft Windows 95 compliant 16 bit driver For information on installing and using the software see the software manual The scanner can accommodate 4x5 2 1 4 x 2 1 4 2 1 4 x 2 3 4 and 35mm film formats In the 35mm format size up to four images can be scanned at once The unit can operate at volt ages from 100V to 240V The SprintScan 4
10. co Polaroid Caribbean Corporation Centro de Seguros Ave Ponce de Le n 701 M iramar Santurce 00907 Tel 809 725 6240 Fax 809 725 5462 Schweiz Suisse Svizzera Polaroid AG H ardturmstrasse 133 8037 Zurich Tel 01 277 72 72 Suomi Polaroid Oy Sinikalliontie 10 02630 Espoo Puh 90 502 35 33 Fax 90 502 35 50 Sverige Polaroid AB Ekholmsvagen 34 Box 204 127 24 Skarholmen Tel 08 710 08 50 Fax 08 740 73 68 Care and maintenance 3 5 Radio and television interference FCC Notice U S A Note This equipment M odel CS 4500 has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment gen erates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications H owever there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient relocate the receiving antenna e Increase the separation between the equipment and receiver
11. d an Intel Pentium microprocessor is recommended s 16M B of RAM is required 32M B or more of RAM is recom mended e An 8 bit color monitor is required a 24 bit color monitor is recommended s At least 20M B of free disk space is required a 2GB hard disk is recommended e A removable storage device is recommended s An ASPI compliant SC SI 2 interface board not included Introduction 1 3 Technical Support Hardware support Software support Registration card If you need additional help with your Polaroid SprintScan 45 scanner call us toll free from within the continental United States at 1 800 432 5355 M onday through Friday 8 a m to 8 p m Eastern Time We offer a variety of Customer Support Services call us for details and applicable fees Y ou may also write to Electronic Imaging Technical Support Polaroid Corporation 565 Technology Square 3B Cambridge MA 02139 In Canada call toll free at 1 800 268 6970 Outside the U S A and Canada please consult the Polaroid office nearest you See pages 3 4 3 5 If you need additional help with your application software please contact the manufacturer of the software Be sure to fill out and mail your registration card As a regis tered owner you ll receive information about software updates and about the availability of new scanning products from Polaroid Unpacking The SprintScan 45 scanner is a precision instrument H andle it as carefu
12. e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Note Shielded interface cable with ferrite core installed on scanner connector end must be used with this equipment Caution Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user s authority to operate the equipment 3 6 Media capability Maximum scan time Actual resolution Density range Sensor technology Bits per color Light source Signal processing CCD calibration Interface Operating voltage Appendix A Specifications 35mm to 4x5 in format positive and nagative mounted and unmounted transparencies 26ms RGB line Minimum 72 dpi Maximum 2000 x 4000 dpi 0 0 3 40D Single pass RGB CCD 12 bit A D conversion per RGB 8 bit or 12 bit output to host Cold cathode fluorescent Software based real time color processing Automatic white point adjustment and dark field subtraction SCSI 2 one 50 pin connector and one 25 pin connector Voltage 100 240VAC Frequency 47 66 Hz A 1 Power Accessories Dimensions LxWxH Weight Certifications Environmental requirements 40W Film holders 4x 5in 10 2 x 12 7cm 2 4 x 2 8 in 6x7cm 2 4 x 2 8 in 6 x 6cm 35mm four at once 35mm single mount 21 x 13 x 7 in 53 3 x 33 x 17 8cm 22 Ib 10 kilos CSA NR
13. e carrier at the bottom edge and turn the knob to lock it picture 12 2 12 The single 35mm 1 Open the 4x5 carrier as described previously SE 2 Locate the single 35mm adapter Note Y ou can use a nega tive or a mounted or unmounted slide 3 Orient the adapter so the metal tabs face up and the notches are at the left edge Slide the film into the channel under the two metal tabs Position the film so the image is right reading and right side up picture 13 4 If the film is unmounted or the mount is thin use the slide spacer provided Position the slide spacer underneath the slide picture 14 The film should fit snugly into the adapter The spacer also ensures that the image will be at the correct dis tance from the scanning mechanism D gt 5 Place the adapter in the 4x5 carrier sliding the notches into the pins on the left edge The slide and tabs should be facing up picture 15 6 Close the carrier Squeeze the carrier at the bottom edge and turn the knob to lock it picture 16 16 Setup and use 2 13 Inserting the camer into the scanner 1 Open the carrier access door picture 17 2 Insert the carrier gently and firmly into the carrier slot as shown until you feel it stop picture 18 ae 17 3 Close the carrier access door The scanner will not scan if the door is open Note Do not open the carrier access door while a scan is in process the scan will be interrupted
14. ection tips The SprintScan 45 scanner is unterminated If it is the last device in the chain add a terminator See the illustrations on pages 2 9 2 10 Powerbook note According to Apple Computer even though this computer has an internal hard disk you should treat it as an unterminated device This means that you must have two terminators on the SCSI chain Apple also advises that if you have only one device connected to a Powerbook you must have two terminators on this one device Refer to the documentation included with your PowerBook WARNING ALL CONNECTIONSMUST BE MADE WITH THE POWER OFF ON THE SCANNER THE COM PUTER AND ALL SCSI DEVICES e Always make SCSI connections firmly connecting the clips or tightening the screws that secure cables and terminators M ost problems with SCSI devices are connection problems along the SCSI chain e The SprintScan 45 scanner has two SCSI connectors one has 50 pins and one has 25 A SCSI cable can be connected to either port without affecting the performance of your equip ment Each device on a SCSI chain must havea unique SCSI ID number These numbers are described in the following section s If a 50 to 50 pin cable is required be sure to use a cable which meets the SC SI 2 specification such as an Apple cable 24 SCSI ID numbers Changing the SCSI ID of the scanner m N 3 WARNING TO PREVENT DAMAGETO YOUR HARDWARE AND SOFTWARE READ THISSECTION BEFORE TURNING
15. functioning See Technical Support on page 1 4 3 1 Troubleshooting When the scanner is powered up the POWER indicator should come on and theREADY indicator should flash A few seconds later after the scanner s self test is completed the READY indicator should shine steadily The scanning lamp will come on and should stay on all the time Problems can usually be detected when the power is first turned on This section covers the most common problems and their solutions The POWER indicator fails to light up Turn the power switch off M ake sure that the scanner s power cord is grounded and plugged into an AC outlet Then try turning on the power again If the scanner indicator still fails to light up the fuse probably needs to be replaced The POWER indicator lights up but the READY indicator fails to stop flashing This can be caused by e a faulty indicator e a faulty or loose lamp e detection of a malfunction during the scanner s power on self test Try initiating a scan in the software the software may report the solution to you The POWER and READY indicators light up but software returns Scanner not ready or similar message M ake sure that the software is set for the correct SCSI ID and that no other device on the SCSI chain uses the same ID The READY indicator continues flashing TheREADY indicator flashes if you try to scan while the front cover of the scanner is open Close the front cover and t
16. h one hand while turning the locking knob in either direction until the slot in the knob points to UNLOCK picture 7 2 10 2 Open the carrier flat Insert a 4x5 chrome or negative so that the left edge is against the positioning pins picture 8 Position the film so the image is right reading and right side up emulsion side down Note The emulsion side is the dull side 3 Close the carrier Squeeze the carrier at the bottom edge and turn the knob to lock it Setup and use 2 11 The 120 film adapters 1 Open the 4x5 carrier as described previously for 2 1 4 x 2 1 4 and 2 1 4 x 2 3 4 in film 2 Locate the appropriate adapter for your image Oneis designed for 2 1 4 x 2 3 4 in images and oneis for 2 1 4 x 2 1 4 in square images Note The frame of film must be cut from the film strip in order to be scanned 3 Orient the adapter so that the words THIS SIDE UP on the adapter face up and the notches are at the left edge picture 9 Place the unmounted film over the opening within the raised ridges of the adapter Position the film so the image is right reading and right side up Secure the film with the two magnets provided on the top and bottom edges Be sure the magnets are also within the raised ridges picture 10 4 Place the adapter in the 4x5 carrier sliding the notches into the pins on the left edge The film and magnets should be face up as shown picture 11 5 Close the carrier Squeeze th
17. lly as you do your hard drive Save the protective packing materials and carton in case you need to move or ship the scanner If you are missing any of the following components contact your dealer immediately a Scanner b Power cable c This manual d Pass through terminator e SCSI cable 25 pin to 50 pin f Film carrier for 4x5 film g Adapter for 120 film 2 1 4 x 2 Ya in h Adapter for single 35mm slide spacer shown on page 2 2 i Adapter for 120 film 2 ax 2 3 ain j Four slide film carrier k Two magnets for 120 film shown on page 2 2 Introduction 1 5 2 Setup and use The scanner and accessories B a Power R eady indicator lights b Film carrier slot c Carrier access door Rear panel a Air intake d Power connector b SCSI ID switch e SCSI connectors 25 50 C Power switch Accessories a 4x5 carrier e Magnets for c and d b Four slide film carrier f Single 35mm slide adapter C 2 1 4 x 2 1 4 in film adapter g 35mm slide spacer d 2 1 4 x 2 3 4 in film adapter 2 2 Positioning the scanner SCSI guidelines Place the scanner on a flat stable surface free of vibration Leave at least 2 inches 50mm of space around all sides and the top of the scanner for adequate ventilation and leave room at the back to reach the power switch on the rear panel Caution As with any highly sensitive optical equipment vibrations or bumping the scanner during use may result in pict
18. o and television interference 3 6 Ready indicator light 2 9 3 2 Registration card 1 4 Relative humidity A 2 Removing the carrier 2 14 Resolution 1 2 A 1 S Scanner description 1 1 accessories 2 2 front panel 2 1 rear panel 2 2 Scanning frame A 1 modes 1 2 A 1 speed A 1 SCSI adapter for a PC 2 6 cable 1 5 2 6 2 8 2 9 chains 2 3 configuration diagrams 2 8 2 9 connectors 2 2 2 4 2 6 guidelines 2 3 2 4 host adapter for the PC 2 6 SCSI ID number 2 4 2 5 SCSI ID switch 2 2 Self test 2 9 Service 3 3 3 4 3 5 Size of document A 1 Slide spacer 2 13 Specifications A 1 A 2 System requirements 1 3 T Technical Support 1 4 Temperature A 2 Termination 2 3 2 7 2 8 2 9 Transmission method A 1 Troubleshooting 3 2 24 bit color mode 1 1 U Unpacking 1 5 V Ventilation 2 3 Voltage range 1 1 2 9 Voltage requirements A 2 W Warranty 3 3 Windows 1 3 l 2 PXW8033 QX CP 3 96 Printed in U S A
19. provided Do not add any additional terminators If one external device has an internal terminator see the previous example Use only approved SCSI cables Tuming on the scanner 1 With the scanner off plug the power cord provided into the scanner picture 4 and then into an appropriate grounded outlet The scanner can operate over a voltage range from 100 to 240 VAC 2 Turn on the scanner the switch is next to the power connector The POWER indicator light on the front of the unit will light the cold cathode lamp will come on visible through the slit on the top of the unit and the READY indica tor will flash briefly The scanner will perform a self test that lasts for a few seconds If no problems are detected the READY light will stay lit The cold cathode lamp will also stay on 3 Once the ready light is lit turn on your computer Setup and use 2 9 Using the film carers The four slide 1 With the text facing up and the hinge at the top open the film carrier carrier flat as shown picture 5 2 Place up to four mounted 35mm slides in the spaces provid ed Be sure the slide mounts fit properly in the recessed areas The images should be right side up and right reading as you do so picture 6 The emulsion side will face down 3 Close the carrier carefully The 4x5 carrier 1 To unlock the carrier squeeze the two halves of the carrier for 4x5 film together at the bottom edge near the locking knob wit
20. ry scanning again 3 2 Limited One Year Equipment Warranty Service Polaroid Corporation warrants your Sprintscan 45 scanner equipment against defects in manufacture for a period of one year from the date of purchase To verify the warranty period you should keep the sales slip or other proof of the purchase date Should this product or any component or accessory included with it except software become defective at any time during the warranty period Polaroid Corporation will at its discre tion either replace or repair this item without charge provid ed the product is returned to a designated service location prepaid and insured For the software warranty please refer to the Software Warranties under the License Agreements This Limited Warranty does not apply to product damage resulting from accident incorrect installation unauthorized modification misuse or abuse A charge will be made for repair of such damage This warranty excludes all consequential damage and does not affect your statutory rights Note Polaroid Corporation reserves the right to make changes or improvements in the product described in this manual at any time and without notice U S A and Canada Outside North America If your Sprintscan 45 scanner requires service please call Polaroid Electronic Imaging T echnical Support from within the U S A at 1 800 432 5355 M onday through Friday 8 a m to 8 p m Eastern Time In Canada
21. the documentation for your adapter The SprintScan 45 scanner is compatible with most Windows ASPI supported adapters such as Adaptec For detailed information about installing the card refer to the instructions provided with your adapter card Connecting the scanner to your computer WARNING ALL CONNECTIONS MUST BE MADE WITH THE POWER OFF ON THE SCANNER THE COM PUTER AND ALL OTHER CONNECTED EQUIPMENT PAY STRICT ATTENTION TO THE SEQUENCE OF INSTRUCTIONSIN THIS SECTION FAILURE TO COMPLY MAY RESULT IN DAMAGE TO YOUR COM PUTER AND OR THE SCANNER SUCH DAMAGE ISNOT COVERED BY THE WARRANTY m Turn off your computer and then turn off the scanner N Connect the 25 pin end of the data cable to the SCSI port on the back of your computer and the 50 pin end to the 50 pin port on the back of the scanner picture 2 Warning Use only the cable supplied with the scanner 2 6 The second port 25 pin can be used to connect another SCSI device to the chain using another SCSI cable 3 Terminate the signal at the last device in the chain If the scan ner is the last device connect the terminator provided to the 50 pin port Then connect the SCSI cable to the terminator picture 3 Be certain to use only SC Sl specified cables for all connections in the chain For details see pages 2 8 2 9 The diagrams on the following pages will serve as a reference to correct SCSI connections for various system configurations
22. ure defects Locate the unit where it will not be disturbed during use About SCSI chains Termination The SCSI system uses special cables and termination to achieve communication between the computer and peripheral devices To function properly the combined length of the entire cable system must not exceed 19 1 2 feet 6 meters and must include the appropriate number of terminators Termination maintains the clarity of the SCSI signal along the chain of devices A SCSI chain must always be terminated at both ends Incorrect termination can permanently damage the computer scanner or any other device along the SCSI chain R efer to the following guidelines and diagrams for more information The SCSI chain must be terminated at both ends of the chain The beginning of the chain is typically the computer M ost M acintosh computers include a hard disk which is internally terminated If your computer does not include an internally terminated hard disk you must place an external terminator on the first device after the computer between the device and the SCSI cable to the computer Intermediate devices in the chain should not be terminated If you have an internally terminated device place it at the end of the chain Check the manual for the device to determine if it is internally terminated or not If none of your devices are internally terminated place an external terminator on the last device Setup and use 2 3 Conn
Download Pdf Manuals
Related Search