Planet Technology WAP-4030A User's Manual
Contents
1. 23 3 4 24 3 5 WE P 26 3 6 WV ASST tees 27 Chapter 4 Troubleshooting 28 Chapter 1 Introduction Thank you for purchasing WAP 4030A The WAP 4030A supports both IEEE 802 116 and IEEE 802 119 standards You can use it to connect an existing WLAN or to build up a new wireless LAN Except for essential AP mode WAP 4030A also provides Repeater Bridge and Client modes to accommodate all kinds of network topology High data rate up to 54Mbps support allows faster communication between LAN and WLAN Maximize network efficiency while minimizing your network investment and maintenance costs The WAP 4030A provides the most security functions such as 64 128 bit WEP Wired Equivalent Privacy Encryption WPA PSK and MAC address filter to consolidate the wireless network security There is no chance for the unauthorized wireless stations to access your wireless network With the user friendly management interface and versatile features WAP 4030A is the best choice to integrate your wireless and wired network seamlessly 1 1 Package Contents Make sure that you have the following items 1x WAP 4030A 1x Power Adapter 1x User s Manual CD 1x Quick Installation Guide 1x External Antenna If any of the above items are missing contact your supplier as soon as possible2. PLANET Hetworing Commenicaiion 54Mbps Wireless Access Point w bridge inter building WAP 4030A Users Manual Copyright Copyright 2005 by PLANET Technology Corp All rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission of PLANET PLANET makes no representations or warranties either expressed or implied with respect to the contents hereof and specifically disclaims any warranties merchantability or fitness for any particular purpose Any software described in this manual is sold or licensed as is Should the programs prove defective following their purchase the buyer and not PLANET its distributor or its dealer assumes the entire cost of all necessary servicing repair and any incidental or consequential damages resulting from any defect in the software Further PLANET reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes All brand and product names mentioned in this manual are trademarks and or registered trademarks of their respective holders Federal Communication Commission Interference Statement This equipment has been tested a
3. Access Point The Repeater mode configuration is include two parts The upper part is use to show which device the WAP 4030A will connect The lower part is set this WAP 4030A configuration So you will see a SSID option in lower part WAP 4030A can work with its own SSID to wireless network That can prevent users confuse on they are select the AP with the same SSID and different MAC Address in Site Survey screen Users can clearly knew which AP they should connected with this new setting When Universal Repeater mode selected you will need to enter the remote Access Point s SSID When Universal Repeater mode selected please select the same Channel as the remote Access Point When WDS Repeater mode selected please enter remote Access Point s MAC Address into this field When WDS Repeater mode selected you can enable this option to connect second WDS Repeater mode WAP 4030A to your WDS Repeater mode WAP 4030A In second WDS Repeater mode WAP 4030A you will need to set the Parent MAC Address as the first WDS Repeater mode WAP 4030A s MAC address 802 11b mode It allows to select the transmit rate up to 11Mbps 802 11g mode It allows to select the transmit rate up to 54Mbps Mixed mode It provides best performance for 11g transmission when you enable the AP mode selection to Mixed mode The SSID up to 32 printable ASCII characters is the unique name identified in a WLAN The ID prevents the unintentional merging of two co locat
4. 1 2 System Requirements Before installation please check the following requirements with your equipment Pentium Based or above IBM Compatible PC System CD ROM drive Windows 98 Me NT 2000 XP Server2003 Operating System with TCP IP protocol 1 3 Features o Compliant with the IEEE 802 11g 802 11b DSSS 2 4GHz specification High data rate up to 54Mbps Auto rate fallback Seamlessly integrate wireless and wired Ethernet LAN networks Provide WPA PSK 64 128 bit WEP Encryption MAC Filter to protect the wireless data transmissions Support Wireless AP Client Repeater and Bridge mode Support MAC Address Filter Support DHCP client for auto IP address assignment Provide a reverse polarity SMA connector for external antenna connection Auto Fall Back Data Rate for Long Distance communication and noisy environment Web based configuration 1 4 Specification Standard IEEE 802 144 802 11b Frequency Band 2 400 2 4835GHz Tran sfer Rate 802 119 54 48 36 24 18 12 9 6Mbps 802 11b 11 5 5 2 1 Mbps Modulation OFDM CCK DQPSK and DBPSK Sensitivity IEEE802 11b 92dBm 1Mbps 89dBm 2Mbps 87dBm 5 5Mbps 82dBm 11Mbps IEEE802 11g 91dBm 6Mbps 90dBm 9Mbps 87dBm 12Mbps 82dBm 18Mbps 82dBm 24Mbps 78dBm 36Mbps 71dBm 48Mbps 71dBm 54Mbps Channel FCC 11 Channels US Canada ETSI 13 Channels Europe ELEC 14 Channels Japan LED Indicators 3 PWR WLAN LAN Po
5. CA plus Acknowledge protocol Multi Channel Roaming Automatic Rate Selection RTS CTS feature Fragmentation Power Management Q What is Infrastructure A An integrated wireless and wired LAN is called an Infrastructure configuration Infrastructure is applicable to enterprise scale for wireless access to central database or wireless application for mobile workers Q What is Roaming A Roaming is the ability of a portable computer user to communicate continuously while moving freely throughout an area greater than that covered by a single Wireless Network Access Point Before using the roaming function the workstation must make sure that it is the same channel number with the Wireless Network Access Point of dedicated coverage area 28
6. If you select Only deny PCs with MAC listed below to access this device then all the PCs in the list will be denied to access and all other PCs will be allowed to access If you select Only allow PCs with MAC listed below to access this device then all PCs in the list will be allowed to access but all other PCs will be denied to access Filter List Enter the MAC address of PC that will be managed by the MAC Filtering rule Please click Apply button to save the above configurations 16 3 1 3 Repeater Mode In this mode WAP 4030A can be a repeater between Access Point and wireless clients that can extend the connect distance of your Access Point When it works in this mode it will also work as an access point WAP 4030A has provided two repeater modes you may select the suit one to your wireless network e PLANET Be ihig E Tru NOTE Repeater Type Parent 551D Channel Parent Address MODE SSID Broadcast 55ID Security Advanced Settings Access Filter Parameter Repeater Type Y Mode Status Admin LAN Please note that all repeater settings are duplicated from Access Point settings If you need to make changes please do so below If these changes are applied they will also he duplicated when you choose to active the Access Point wos Repeater What s This Channel amp 0 00 00 00 00 00 Enable Linked Repeater 00 00 00 00 00 00 C gu2 11b C
7. Parameter Station Mode MAC Cloning Mode SSID Site Survey Operation Mode Admin LAN C 802 11b Mixed Disabled Enabled Defautt Site Survey C Ad Hoc Infrastructure Disable WEP C WPA Setup C Short Long Auto rr Apply Cancel Description 802 11b It allows to select the transmit rate up to 11Mbps Mixed It allows to select the transmit rate up to 54Mbps Disabled It will use it s own MAC address to access the wireless LAN Enabled It will use PC s MAC address to access the wireless LAN The SSID up to 32 printable ASCII characters is the unique name identified in a WLAN The ID prevents the unintentional merging of two co located WLANs Please make sure that the SSID of all stations in the same WLAN network are the same The default SSID is default Click Site Survey button then a Wireless Site Survey Table will pop up like below It will list all the available access points near by You can select one access point in the table and it will join wireless LAN through this access point SSID Security Channel Signal Network Type C Wireless disabled 3 infrastructure Scan Join Close AD Hoc It can let your network device join a wireless LAN with peer to peer communication 11 Channel Security Preamble Type Transmit Rate Infrastructure It can let your network device join a wireless LAN through an access point Select t
8. WPA PSK WPA Authentication Method Passphrase Clear PSK Pre Shared keys Group Re Key Time ouo Apply Close Parameter Description Authentication Type The Pre shared key is used to authenticate and encrypt data transmitted in the wireless network Passphrase To entry at least 8 character pass phrase as the pre shared keys Please click Apply to save the above configurations 27 Chapter 4 Troubleshooting This chapter provides answer to problems usually encountered during the installation and operation of the Wireless Network Access Point Read the description below to solve your problems Q Can run an application from a remote computer over the wireless network A This will depend on whether or not the application is designed to be used over a network Consult the application s user guide to determine if it supports operation over a network Q Can play games with other members of the cordless network A Yes as long as the game supports multiple plays over a LAN local area network Refer to the game s user guide for more information Q What is the IEEE 802 11g standard A The IEEE 802 11g Wireless LAN standards subcommittee which is formulating a standard for the industry The objective is to enable wireless LAN hardware from different manufactures to communicate Q What IEEE 802 11 features are supported A The product supports the following IEEE 802 11 functions e CSMA
9. function your data will be transmitted over the wireless network securely Please refer to section 3 5 to configure It provides more powerful features for you to configuring Please refer to section 3 1 4 1 Please click Apply button to save the above configurations 20 3 1 4 1 Advance Setting RTS Threshold 2347 range 256 2347 default 2347 OTIM Interval range 1 255 default 2 Protection Mode Disable Enable Transmit Rate Auto Short Long Auto Parameter RTS Threshold DTIM Period Protection Mode Transmit Rate Preamble Type Apply Close Description When the packet size is smaller the RTS threshold the access point will not use the RTS CTS mechanism to send this packet This is the interval of the Delivery Traffic Indication Message DTIM A DTIM field is a countdown field informing stations of the next window for listening to broadcast and multicast messages When the Access Point has buffered broadcast or multicast messages for associated stations it sends the next DTIM with a DTIM Interval value Stations for the Access Point hear the beacons and awaken to receive the broadcast and multicast messages It provides best performance for 11g transmission when you enable it When you enable the standard mode to 802 11b and it allows you to select the speed of 1 11Mbps When you enable the standard mode to 802 11g and it allows you to se
10. stations of the next window for listening to broadcast and multicast messages When the Access Point has buffered broadcast or multicast messages for associated stations it sends the next DTIM with a DTIM Interval value Stations for the Access Point hear the beacons and awaken to receive the broadcast 14 and multicast messages Protection Mode t provides best performance for 11g transmission when you enable it Transmit Rate When you enable the station mode selection to 802 116 and it allows you to select the speed of 1 11Mbps When you enable the station mode selection to 802 119 and it allows you to select the speed of 1 54Mbps Preamble Type Preamble type defines the length of preamble block in the frames during the wireless communication Auto It will auto switch to the more suitable method Short It is suitable for high traffic wireless network Long It can provide more reliable communication Please click Apply button to save the above configurations 15 3 1 2 2 Access Filter This Access Point allows you to provide a Filter List of MAC addresses that are allowed denied associating with this AP Enable Disable Filter Filter List Only deny PCs with MAC listed below ta access this device C Only allow PCs with MAC listed below ta access this device Apply Close Parameter Description MAC Filtering You can enable or disable the MAC Filtering function Filter Mode
11. 07 Close 3 3 Admin You can upgrade WAP 4030A with latest firmware and assign a new password in this screen 23 e PLANET eo TQ ru Mode Status Admin LAN FW Version FW Upgrade Browse New Password Reconfirm Password Apply Description FW Version It shows the current firmware version FW Upgrade This tool allows you to upgrade WAP 4030A firmware Before upgrade you will need to download the firmware file from internet to your local hard disk and enter that file name and path in the appropriate field on this page You can also use the Browse button to find out the firmware in your PC Please restart WAP 4030A after upgrade process is complete New Password Enter the password up to 32 digit alohanumeric string you want to login to the Access Point Note that the password is case sensitive Reconfirm Password Reconfirm the password that you have enter above Please click Apply save the above configurations 3 4 LAN You can assign a new device name and IP Address in this option 24 Bese ete Mode Status Admin LAN Device Name Automatic IP Ee Important Fixed IP Specify IP Subnet Mask 255 Gateway Parameter Description Device Name It shows current device name Automatic IP If there is a DHCP Server in your LAN you can select this option to let this WAP 4030A get an IP address from the DHCP Server Bef
12. 802 110 Mixed betat C Disable Enable Disable C WEP WPA setup Setup Setup Apply Cancel Description WAP 4030A has support two type of Repeater mode WDS Repeater and Universal Repeater When different Repeater mode selected you will also enter different settings WDS Repeater Please enter the remote Access Point s MAC address into Parent MAC address field This mode allows you to connect second WDS Repeater mode WAP 4030A to this WDS Repeater mode WAP 4030A You can check the Enable Linked Repeater and enter the second WDS Repeater WAP 4030A s MAC Address in this field So you can use two WDS Repeaters to extended the connect distance of your Access Point Normally you cannot connect a Repeater to another Repeater except WDS Repeater mode WAP 4030A You can use one more WDS Repeater mode WAP 4030 to extended your connect distance With this function we have to remind you one thing when wireless clients connect to first WDS Repeater the performance will 17 Parent SSID Channel Parent MAC Address Enable Linked Repeater Mode SSID Broadcast SSID be 50 as the clients connect to AP directly When clients connect to second WDS Repeater the performance will be 25 Universal Repeater This repeater mode will connect your WAP 4030A to the Access Point when the SSID and channel are the same You will need to enter remote AP s SSID to Parent SSID field and set the Channel the same as your
13. A to default settings press the Reset button 5 second Then release the button and wait for 10 seconds for rebooting Chapter 3 Configuring the Wireless AP Web configuration provides a user friendly graphical user interface web pages to manage your WAP 4030A An AP with an assigned IP address e g http 192 168 0 1 will allow you to monitor and configure via web browser e g MS Internet Explorer or Netscape 1 Open your web browser 2 Enter WAP 4030A IP address default IP address is hitp 192 168 0 1 into the address field of the web browser Please also make sure your PC s IP address is in the same IP range with WAP 4030A 3 AUser name and Password dialog box will appear Please enter your User name and Password here Default User name and Password is admin Click OK Connect to 192 168 0 1 Remember my password x 4 Then you will see the WAP 4030A configuration screen in the web page as the picture in section 3 1 3 1 Operating Mode In this screen you can see all the operating modes of WAP 4030A In Default WAP 4030A is work with Access Point mode Please select the operating mode you want and press Setup button Then you can configure WAP 4030A to the operating mode If the mode configuration had be done in before you can select the operating mode and press Apply button without configure again e PLANET ECL ru Mode Status Admin LAN Current Mode AP Mode This
14. ed WLANs Please make sure that the SSID of all stations in the same WLAN network are the same The default SSID is Default It will respond to Broadcast SSID requests If you enable this function every wireless station located within the coverage of this access point can discover this 18 Security Advance setting Access Filter access point easily If you are building a public wireless network enabling this feature is recommended Disabling Response to Broadcast ESSID requests can provide better security Disable Disable the security function WEP WEP is an authentication algorithm which protects authorized Wireless LAN users against eavesdropping The Authentication type and WEP key of wireless stations must be the same with the Access Point This Access Point supports 64 128 bit WEP Encryption function With this function your data will be transmitted over the wireless network securely Please refer to section 3 5 to configure WPA You can use a pre shared key to authenticate wireless stations and encrypt data during communication When you enabled WPA mode you can not use WEP encryption Please refer to section 3 6 to configure It provides more powerful features for you to configuring Please refer to section 3 1 2 1 This Access Point allows you to provide a Filter List of MAC addresses that are allowed associating with this AP Please refer to 3 1 2 2 Please click Apply button to save the above configurat
15. he antenna you want to use and make sure it can be used on WAP 4030A 4 WLAN Type If WAP 4030A is installed in an 802 11b and 802 11g mixed WLAN its performance will reduced significantly Because every 802 11g OFDM packet needs to be preceded by an RTS CTS or CTS packet exchange that can be recognized by legacy 802 11b devices This additional overhead lowers the speed If there are no 802 11b devices connected or if connections to all 802 11b devices are denied so that WAP 4030A can operate in 11g only mode then its data rate should actually 54Mbps Chapter 2 Hardware Installation Before you proceed with the installation it is necessary that you have enough information about the WAP 4030A 2 1 Hardware Connection Ld ae RESET ANT 1 Locate an optimum location for the WAP 4030A The best place for your WAP 4030A is usually at the center of your wireless network with line of sight to all of your mobile stations 2 Assemble the antenna to WAP 4030A Try to place them to a position that can best cover your wireless network The antenna s position will enhance the receiving sensitivity 3 Connect RJ 45 cable to WAP 4030A Connect this WAP 4030A to your LAN switch hub or a single PC 4 Plug in power adapter and connect to power source After power on WAP 4030A will start to work Note ONLY use the power adapter supplied with the WAP 4030A Otherwise the product may be damaged If you want to reset your WAP 4030
16. he appropriate channel from the list provided to correspond with your network settings Channels differ from country to country Channel 1 11 North America Channel 1 14 Japan Channel 1 13 Europe Disable Disable the security function WEP It is an authentication algorithm which protects authorized Wireless LAN users against eavesdropping The Authentication type and WEP key of wireless stations must be the same with the Access Point It supports 64 128 bit WEP Encryption function With this function your data will be transmitted over the wireless network securely You may refer to section 3 5 to know the detail settings of it WPA You can use a pre shared key to authenticate wireless stations and encrypt data during communication You may refer to section 3 6 to know the settings of it Preamble type defines the length of preamble block in the frames during the wireless communication Short It is suitable for high traffic wireless network Long It can provide more reliable communication When you enable the station mode selection to 802 116 and it allows you to select the speed of 1 11Mbps When you enable the station mode selection to 802 119 and it allows you to select the speed of 1 54Mbps Click Apply button at the bottom of the screen to save the above configurations You can now configure other advance sections or start using WAP 4030A 3 1 2 Access Point Mode AP Mode provides pure access point funct
17. he transmit rate up to 11Mbps 802 11g mode It allows to select the transmit rate up to 54Mbps Mixed mode It provides best performance for 11g transmission when you enable the AP mode selection to Mixed mode Select the appropriate channel from the list provided to correspond with your network settings Disable Disable the security function WEP WEP is an authentication algorithm which protects authorized Wireless LAN users against eavesdropping When this function enable please make sure you have set all the WAP 4030As to the same WEP key You may refer to section 3 5 to set the WEP key It provides more powerful features for you to configuring Please refer to section 22 3 1 4 1 to configure Please click Apply button to save the above configurations 3 2 Status In this option you can see the WAP 4030A current settings e PLANET fe E ru E 2 aam E Mode Status Admin LAN 00 30 4F 03 47 1E IP Address 192 165 1 1 Subnet Mask 255 ue 255 0 Gateway 0 0 0 0 Link Up 100 Mbps 00 30 4F 103 47 1B SSID Default Channel E Coexistence B02 11b g Mixed Encryption Function Not Required Link Up Auto rate Station List When it is work AP mode you press the Station List button to know which client is connected to this AP like below Ho MAC Address Status 00 30 4F 00 00
18. horized Wireless LAN users against eavesdropping The Authentication type and WEP key of wireless stations must be the same with the Access Point It supports 64 128 bit WEP Encryption function With this function your data will be transmitted over the wireless network 13 securely You may refer to section 3 5 to know the detail settings of it WPA You can use a pre shared key to authenticate wireless stations and encrypt data during communication You may refer to section 3 6 to know the settings of it Advance setting It provides more powerful features for you to configuring Access Filter This Access Point allows you to provide a Filter List of MAC addresses that are allowed associating with this AP Please click Apply button to save the above configurations 3 1 2 1 Advance setting Beacon Interval 100 msec range 20 1000 default 100 EE 2347 range 256 2347 default 2347 2 range 1 255 default 2 Disable Enable Transmit Rate auto miU Short Long Auto Parameter Description Beacon Interval The period of time that this access point broadcast a beacon Beacon is used to synchronize the wireless network RTS Threshold When the packet size is smaller the RTS threshold the access point will not use the RTS CTS mechanism to send this packet DTIM Period This is the interval of the Delivery Traffic Indication Message DTIM A DTIM field is a countdown field informing
19. ion The simplest way to build up a wireless LAN is to use AP Mode 12 Be irisi g eo oe Mode Status Admin LAN WIKRE C 802 11b C 802 414 Mixed SSID Defautt Disable Enable Channel Channel Disable C WEP C WPA Setup Advanced Settings Setup Access Filter Setup Apply Parameter Description Mode 802 11b mode It allows to select the transmit rate up to 11Mbps 802 11g mode It allows to select the transmit rate up to 54Mbps Mixed mode It provides best performance for 11g transmission when you enable the AP mode selection to Mixed mode SSID The SSID up to 32 printable ASCII characters is the unique name identified in a WLAN The ID prevents the unintentional merging of two co located WLANs Please make sure that the SSID of all stations in the same WLAN network are the same The default SSID is default Broadcast SSID It will respond to Broadcast SSID requests If you enable this function every wireless station located within the coverage of this access point can discover this access point easily If you are building a public wireless network enabling this feature is recommended Disabling Broadcast ESSID can provide better security Channel Select the appropriate channel from the list provided to correspond with your network settings Security Disable Disable the security function WEP An authentication algorithm that can protect aut
20. ions 3 1 4 Point to Point Mode This function provides to bridge for 2 wired Ethernet networks to connect to each other by wireless You can use two WAP 4030s in P2P mode to connect two wired Ethernet networks together 19 rE fee ru Mode Status Admin LAN AP MAC Address Channel Security Advanced Settings Parameter AP MAC Address Mode Channel Security Advance setting Please note that all PZP settings are duplicated from Access Point settings If you need to make changes please do so below If these changes are applied they will also be duplicated when you choose to active the Access Point C 802 11b 802444 Mixed Channel 6 Disable WEP Setup Setup Apply Cancel Description You have to enter the MAC addresses of another WAP 4030A that it will connect to 802 11b mode It allows to select the transmit rate up to 11Mbps 802 11g mode It allows to select the transmit rate up to 54Mbps Mixed mode It provides best performance for 11g transmission when you enable the AP mode selection to Mixed mode Please select the same channel on both WAP 4030A Disable Disable the security function WEP WEP is an authentication algorithm which protects authorized Wireless LAN users against eavesdropping The Authentication type and WEP key of wireless stations must be the same with the Access Point This Access Point supports 64 128 bit WEP Encryption function With this
21. lect the speed of 1 54Mbps In default it will set to Auto Preamble type defines the length of preamble block in the frames during the wireless communication Auto It will auto switch to the more suitable method Short It is suitable for high traffic wireless network Long It can provide more reliable communication Please click Apply button to save the above configurations 21 3 1 5 Point to Multipoint Mode This function provides to bridge more than 2 wired Ethernet networks together by wireless connection You can use more than two WAP 4030A with P2MP mode to connect those wired Ethernet networks together PLANET Mode Status Admin LAN 1 MAC Address AP MAC Address AP3 MAC Address AP4 MAC Address APS MAC Address AP6 MAC Address MODE Channel security Advanced Settings Parameter AP MAC Address Mode Channel Security Advance setting Please note that all PMP settings are duplicated from Access Point settings If you need to make changes please do so below If these changes are applied they will also be duplicated when you choose to active the Access Point C 802 11b 802 114 Mixed Disable C WEP Setup Setup Apply Cancel Description If you want to bridge more than two wired Ethernet networks together with wireless connection you have to enter the MAC addresses of otherWAP 4030As that with join the bridging work into the fields 802 11b mode It allows to select t
22. mode allows you to connect to an AP or Wireless Router The computer Sitong C Setup or gaming device connected connected to the 5 in 1 now becomes a client on the Wireless LAN network Access Point Setup This mode allows you connect the Wired for Ethernet portion to a router and create a Wireless LAN network This is the default mode selection This mode allows you to extend the range of an AP or Wireless Router Out of repeater This allows you ta connect for bridge between LAN networks In this mode Setup only another AP or Router can be connected no wireless clients can be connected Setup reach clients can connect to the AP or Router by associating with the C C SED This mode Pointto Multipoint allows you to connect many AP or Routers together Apply 3 1 1 Client Mode In this screen you can configure WAP 4030A as a wireless client It is used to let a network device with only wired Ethernet function to have wireless LAN communication capability It provides both Ad Hoc and Infrastructure modes for the Client Mode With Ad Hoc mode it can let your network device join a wireless LAN with peer to peer communication With Infrastructure mode it can let your network device join a wireless LAN through an access point 10 PLANET Ba M ru Mode Status Station Mode MAC Cloning Mode 951 Operation Mode Channel Security Preamble Type Transmit Rate
23. nce with Frequency channel restrictions Germany Greece Ireland Italy Luxembourg The Netherlands Portugal Spain Sweden and United Kingdom The ETSI version of this device is also authorized for use in EFTA member states Iceland Liechtenstein Norway and Switzerland Potential restrictive use France Only channels 10 11 12 and 13 Revision User s Manual for PLANET Wireless Access Point Model WAP 4030A Rev 2 0 June 2005 Part No EM WAP4030Av2 TABLE OF CONTENTS Chapter 1 Introduction 5 1 1 PACKAGE GOMES m 5 1 2 oyster 8 1 5 mto uM UEM ISI mE EE 5 1 3 oco 5 1 4 oDecIfiGallolTa sese M MEM Se ee 6 1 5 erp o iust OE hie Nie Prats dat Chapter 2 Hardware Installation 8 2 1 FIA Wale CONECO 8 Chapter 3 Configuring the Wireless AP 9 3 1 Qier eisdem 9 3 1 1 CHO esee M 10 3 1 2 lveerccNcalgdtasA 12 3 1 3 Repeater MOJE ecoin Et 17 3 1 4 Foint fo Polnt MOO C iessen a Raa e RI E aR E RaT 19 32125 Point to Multipoint Mode eroe eae deoa depu oae cea pen dee une saints 22 3 2 Pie 23 3 3 Din me
24. nd found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio technician for help FCC Caution To assure continued compliance example use only shielded interface cables when connecting to computer or peripheral devices Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the Following two conditions 1 This device may not cause ha
25. ore work with Automatic IP please press Important button and check the content inside Fixed IP Specify IP Designate the Access Point s IP Address This IP Address should be unique in your network The default IP Address is 192 168 0 1 Subnet Mask Specify a Subnet Mask for your LAN segment Gateway Specify the default gateway IP of this Access Point Please click Apply button to save the above configurations 25 3 5 WEP WEP MS WEP 54 WEP 128 DILE HEX ASCII Passphrase Generate Clear Key 1 77 Keyl Key Key3 Keyd Apply Close Parameter Description WEP Length WEP 64 input 10 digit Hex values 5 digit ASCII character as the encryption keys WEP 128 input 26 digit Hex values or 13 digit ASCII characters as the encryption keys Mode You may select to select ASCII Characters alphanumeric format or Hexadecimal Digits the A F and 0 9 range to be the WEP Key For example HEX 12345abcde ASCII guest Passphrase Enter passphrase and click Generate then the access point will automatically generate WEP keys by the passphrase for you Key 1 Key 4 The WEP keys are used to encrypt data transmitted in the wireless network Default TX Key Select the WEP key used to encrypt data transmitted in the wireless network Please click Apply to save the above configurations 26 3 6
26. rmful interference and 2 this Device must accept any interference received including interference that may cause undesired operation Federal Communication Commission FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment In order to avoid the possibility of exceeding the FCC radio frequency exposure limits human proximity to the antenna shall not be less than 20 cm 8 inches during normal operation R amp TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999 5 CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity R amp TTE The R amp TTE Directive repeals and replaces in the directive 98 13 EEC Telecommunications Terminal Equipment and Satellite Earth Station Equipment As of April 8 2000 Safety This equipment is designed with the utmost care for the safety of those who install and use it However special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment EU Countries Not Intended for Use The ETSI version of this device is intended for home and office use in Austria Belgium Denmark Finland Fra
27. wer 12V DC 1A Temperature 0 55 C Operating Humidity 10 90 non condensing Operating Dimension 169 x 87 x 30 mm Weight 155g Emission FCC Class B CE mark 1 5 Wireless Performance The following information will help you utilizing the wireless performance and operating coverage of WAP 4030A 1 Site selection To avoid interferences please locate WAP 4030A and wireless client away from transformers microwave ovens heavy duty motors fluorescent lights and other industrial equipments Keep the number of walls or ceilings between AP and clients as few as possible Otherwise the signal strength may be seriously reduced Place WAP 4030A in a open space or add additional WAP 4030A as needed to improve the coverage 2 Environmental factors The wireless network is easily affected by many environment factors Every environment is unique with different obstacles construction materials weather etc It is hard to determine the exact operation rage of WAP 4030A in a specific location without testing 3 Antenna adjustment The bundle antenna of WAP 4030A is adjustable Firstly install the antenna pointing straight up then smoothly adjust it if the radio signal strength is poor But the signal reception is definitely weak in some certain areas such as location right down the antenna Moreover the original antenna of WAP 4030A can be replaced with other external antennas to extend the coverage Please check the specification of t
Download Pdf Manuals
Related Search