Pelco MPT115DT User's Manual
Contents
1. 1 0 WARNINGS Prior to installation and use of this product the follow ing WARNINGS should be observed 1 Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes 2 Unless the unit is specifically marked as a NEMA Type 3 3R 3S 4 4X 6 or 6P enclosure it is de signed for indoor use only and it must not be in stalled where exposed to rain and moisture 3 Use only installation methods and materials ca pable of supporting four 4 times the maximum specified load 4 Only use replacement parts recommended by Pelco Please thoroughly familiarize yourself with the infor mation in this manual prior to installation and opera tion PELLO MPT24DT MPT115DT and MPT220DT Series Pan Tilt Controls Installation Operation Manual C520M Rev B 6 92 2 0 SCOPE The information contained within this manual covers the installation and operation of the MPT24DT MPT115DT and MPT220DT Series Pan Tilt Controls 3 0 DESCRIPTION The MPT24DT and MPT115DT Series controls are designed to provide control for Pelco 24 VAC 120 VAC and 230 VAC panytilts Pan tilt movement is controlled by an eight position joystick up down left right and simultaneous combinations of pan tilt functions when move diagonally In addition to manual control and continuous auto scan operations the MPTA24DT and MPTA115DT offer the revolutionary new random scan feature available onl2. ing circuit detects the absence of the motor drive circuit and reverses scan direction MPT24DT MPT24DT 220 MPTA24DT MPTA24DT 220 MPT115DT MPTA115DT MPT220DT MPTA220DT 1 amp SB 3 wire grounded 18 Awg Amp CPCtype 14 pin mate supplied 5 plus ground no additional conduc tors for auto random scan Refer to the specifications for the spe cific pan tilt to be used with the control Pelco Manual C520M Rev B 6 92 GENERAL Construction Cover Steel black polyester powder coat Chassis Steel zinc plated Panel Aluminum black polyester powder coat and white silkscreen Dimensions See Figure 3 Weight MPT24DT MPTA24DT 5 lbs 2 27 kg MPT115DT MPTA115DT 3 Ibs 1 36 kg MPT220DT MPTA220DT 3 Ibs 1 36 kg Shipping Weight MPT24DT MPTA24DT 7 lbs 3 17 kg MPT115DT MPTA115DT 5 Ibs 2 27 kg MPT220DT MPTA220DT 5 Ibs 2 27 kg Rating NEMA 1 8 90 5 50 lt 22 61 LEFT RIGHT DOWN FRONT PANEL REAR PANEL NOTE VALUES IN PARENTHESES ARE CENTIMETERS ALL OTHERS ARE INCHES Figure 3 Dimension Drawing Pelco Manual C520M Rev B 6 92 8 0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on FT FR8000 Series fiber optic products Three years on Genex Series products multiplex
3. VAC input CE MPT115DT Desk top joystick control module 120 VAC input for 120 VAC pan tilts UL MPTA1I5DT Desk top joystick control module 120 VAC input capable of auto random scan operations for 120 VAC pan tilts UL MPT220DT Desk top joystick control module 230 VAC input for use with 230 VAC pan tilts MPTA220DT Same as MPT220DT except capable of auto random scan operation 3 2 OPTIONS CO6HWC DT200 R300 RB115 RB24 Pre wired interconnecting cable 6 foot 1 82 m for use with hard wire con trols using 14 pin control connector UL Dual desk top mount kit two units can be mounted side by side in one desk top chassis Rack kit for up to three control mod ules Blank filler panels provided for less than three modules Relay box for 120 VAC pan tilts and scanners Extends operating distance control to relay box up toamaximum of 13 000 feet 3 962 m utilizing 16 Awg Relay box for 24 VAC pan tilts and scanners Extends operating distance control to relay box up toamaximum of 13 000 feet 3 962 m utilizing 16 Awg Pelco Manual C520M Rev B 6 92 4 0 INSTALLATION 4 1 CONNECTOR ASSEMBLY Installation and or testing will require you to assemble the connector parts provided Fabricate the intercon necting cable according to the following steps refer ence Figure 1 1 Slide part A of the cable clamp item 1 over the end of the cable item 1 part C with the threaded end
4. of the cable clamp facing the connector item 5 2 If the cable has a diameter less than 1 2 inch 1 3 cm slide the rubber boot item 2 over the end of the cable and pull through the cable clamp to so that the boot encases the cable and forms a good seal 3 Strip back the cable jacket approximately 1 1 4 inches 3 2 cm and separate the individual con The contact pins supplied with the mating connec tor are the crimp type which may also be sol dered if you so desired item 4 After crimping or soldering the contact pins to the conductors push them into the proper holes in the connector until they snap in place NOTE Contacts cannot be removed from the connector without the use of the appropriate AMP extraction tool which is available from Pelco Slide part A of the cable clamp toward the connec tor and screw the parts together Attach part B item 1 onto part A and connect both parts with the screws provided Connect the cable assembly to the unit and seat the connector by twisting the locking collar until it snaps into position ductors item 3 threaded end of cable clamp N STRIP 1 8 STEPS 3 7 Kaca i 2 A CRIMP INSULATION OUTSIDE JACKET OF CABLE ITEM 5 DETAIL FRONT VIEW FRONT VIEW 37 PIN CONNECTOR 28 PIN CONNECTOR 3 THE MOST COMMONLY USED CONNECTOR PIN OUT CONFIG URATIONS ARE SHOWN HERE REFERENCE THE CONNECTOR 14 2 D
5. RAWING APPLICABLE TO gt YOUR SITUATION FRONT VIEW FRONT VIEW 14 PIN CONNECTOR 9 PIN CONNECTOR Figure 1 Connector Assembly Pelco Manual C520M Rev B 6 92 3 CONTROL PAN TILT P T COMMON OOO LEFT DOO DOWN ee coe i 0060 RIGHT FRONT VIEW SAFETY GROUND FRONT VIEW Figure 2 Wiring Diagram 4 Pelco Manual C520M Rev B 6 92 5 0 OPERATION AND SYSTEM TEST 5 1 MANUAL OPERATION TEST After installing the interconnecting cable between the pan tilt and control plug the control into the AC outlet turn control on and test operation using the following procedures 1 Move the joystick to the UP position the front of the tilt table should move upwards Move the joy stick to the DOWN position the front of the tilt table should move downwards 2 Move the joystick to the LEFT position the unit should pan to the left With the joystick at the RIGHT position the unit should pan to the right 3 Test operation of the diagonal positions of the joy stick which combine both pan and tilt functions simultaneously For example moving the joystick diagonally to the left between LEFT and UP should pan the unit to the left and move the tilt table up 5 2 AUTO RANDOM SCAN OPERATION TEST The MPTA24DT MPTA115DT and MPTA220DT Se ries provide two modes of automatic pan operation Random Scan and continuous Auto Scan After install ing the interconnecting cable between the pan tilt and control plug control i
6. Scan the unit automatically reverts to Random Scan NOTE Pressing AUTO RANDOM while in Random Scan causes a shift to Auto Scan and starts the half hour timer Similarly pressing AUTO RANDOM while in Auto Scan causes a shift to Random Scan and zeros the half hour timer For MPTA24DT MPTA115DT and MPTA220DT manual operation can be activated two ways by pressing MANUAL or by moving the joystick while the unit is in Auto or Random Scan 6 0 MAINTENANCE Under normal operating conditions and usage mainte nance of this equipment is not necessary However if maintenance is required contact a Qualified Service Technician or return to the factory for repair 7 0 SPECIFICATIONS CONTROLS Pan Tilt Auto Random Scan Pilot Lamp 8 position joystick Up down left right and simultaneous combinations of pan tilt functions when joystick is positioned diagonally between two functions 3 position rocker switch AUTO RANDOM ON manual OFF Long life neon ELECTRICAL Input Voltage Auto Random Circuit Output Voltage 24 VAC 120 VAC 230 VAC Fuse Protection Power Cord Connectors Conductor Requirements Cable Distances 120 VAC or 230 VAC 50 60 Hz A noise generator drives a scan dwell flip flop which is logically anded with a direction flip flop causing random scan and random dwell periods as well as random scan direction Upon limit switch activation a current sens
7. ers server and keyboard Three years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty Two years on standard motorized or fixed focal length lenses Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products Two years on Spectra Esprit ExSite and PS20 scanners includ ing when used in continuous motion applications Two years on Esprit and WW5700 Series window wiper excluding wiper blades Eighteen months on DX Series digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video products One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Six months on all pan and tilts scanners or preset lenses used in continuous motion applications thatis preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made
8. nto the AC outlet turn control on and test operation using the following procedures 5 2 1 Random Scan Operation 1 For Random Scan operation activate the rocker switch located on the left side of the control in the AUTO RANDOM position Activation of this switch causes scanning between limits in an un predictable pattern a The scan duration varies randomly between approximately 0 and 60 seconds b At the completion of a scan period a dwell or rest period occurs This dwell period var ies randomly between about 4 seconds and an adjustable 60 to 900 seconds Pelco Manual C520M Rev B 6 92 The MPTA24DT MPTA115DT and MPTA220DT are factory preset for a duty cycle of 50 However Random Scan dwell time is adjustable by installation or removal of diodes CR9 10 and 11 on PCB1500530 Table A shows the available duty cycle com binations c At the completion of a dwell period another scan period is started The direction of this scan period is also randomly determined d When a pan limit is reached scan direction is Table A Available Duty Cycle Combinations Duty Cycle CR11 CR9 CR10 Percent 50 gt O O O OO O O O O O 1 Diode in circuit 0 Diode out of circuit reversed automatically 5 2 2 Continuous Auto Scan For continuous AUTO SCAN activate the rocker switch in the AUTO RANDOM position a second time After approximately one half hour in Auto
9. number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to Pelco 3500 Pelco Way Clovis CA 93612 5699 USA If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco c o Expeditors 473 Eccles Avenue South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002 96 EC of the European Union regarding the disposal of waste electrical and electronic equipment WEEE Contact your local dealer for procedures for recycling this equipment Pelco Manual C520M Rev B 6 92
10. of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco es RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA
11. y from Pelco Random scan is a significant advance in CCTV security surveillance protection that makes con tinuous duty auto scan operations virtually obsolete Pelco 3500 Pelco Way Clovis CA 93612 5699 USA www pelco com 800 289 9100 or 1 559 292 1981 FAX 800 289 9150 or 1 559 292 3827 International customers call 1 559 292 1981 or FAX 1 559 348 1120 Random scan is an effective deterrent to would be in truders because it follows no predictable pattern The scan direction varies randomly as does the scanning time and dwell time 4 60 seconds Random scan makes it impossible for intruders to beat the system because it has none Random scan is not only a powerful weapon to protect your premises but it also increases your equipment life by over 100 while decreasing maintenance costs Its shorter duty cycle reduces gear train and drive motor wear cable fatigue and motor temperature rise Ran dom scan also offers you the flexibility of continuous auto scan operation with a time delay that automati cally returns operations to Random Scan after 30 min utes in continuous auto scan 3 1 MODELS MPT24DT Desk top joystick control module 120 VAC input for use with 24 VAC pan tilts UL MPT24DT 220 Same as MPT24DT except 230 VAC input CE MPTA24DT Desk top joystick control module 120 VAC input capable of auto random scan operation for 24 VAC pan tilts UL MPTA24DT 220 Same as MPTA24DT except 230
Download Pdf Manuals
Related Search