Pelco EH8100 User's Manual
Contents
1. that must be recycled properly to comply with Directive 2002 96 EC of the European Union regarding the disposal of waste electrical and electronic equipment WEEE Contact your local dealer for procedures for recycling this equipment ej REVISION HISTORY Manual Date Comments C1407M 6 94 Original version C1407M A 5 96 Revised to incorporate which deals with the addition of the pressure sensor option kit and associated wiring update and ECO 96 131 and 96 147 which deal with changes to heater kit configurations C1407M B 5 96 anual revised to new format Figure 6 revised to remove pressure sensor switch Refer to manual C1445M for switching wiring Figure 8 and Section 9 0 revised to include grounding lug 8 97 anual revised and renumbered to new format Section 2 2 added for CE and UL Compliance Revised Table B EH8100 Series Enclosure Mechanical Parts List to add EH810626SS Cradle Weld Assembly per ECO 97 047 6 98 Revised Section 3 4 and Figure 5 11 98 Editing changes Revised certifications Figure 8 Tables A and B and specifications Repaginated manual C1407M C 3 00 Revised connector assembly instructions Created separate manual for EH8100 Series Sun Shroud C422MC Moved exploded assembly diagram and parts lists to new maintenance service manual C1407SM Updated manual to new format C1407M D 7 00 Revised manual to include grounding stud on rear plate C1407M E 04 Changed charging pressure from 5 psi to 8 psi 8 04 Removed agency log2. INSTALLATION OPERATION EH8100 Series Pressurized Camera Enclosure 4 e C1407M H 1 07 Contents Important Safety Instructions cali tare LO RNA A 3 Des ription ds ao ld ala dd aa Mio lak eh ee Ah o ino co E 4 Models etl acres ne ele een 4 EA A E LR i fog nthe eta 4 Mounting eien rede a Gal cuca Lactate altace A li Wats So del bod la Lilia Ute ede hl thd i di 4 Camera and Lens Installationi e au Mee oka OA ot oad oacka le Ch en LA BAL 4 Mating Gonnector Asset Jade WOES cols Leni rail poni re ALIA eni Soda BRE o sno 6 Recharging The EnclosUTe tots cae lembi elicoidali piena 7 Power Conmectioniis igs sio at uate ances cee Cueto Duvets amar aaa hare Cee neat a a ds A bad Sab Nahe AREA 7 Operations iui alii ia O O A een aan 7 Maintenant o s t emar da O TITAN a RIA 7 SENICI ei iran ere ee a ea 8 DISEMINAR Adi RS oo Wak BAS NAS iii dere ada a 8 Recharging and ReassemblVi gt Store eee A A A ee To 8 Specifications snai a i Medes ei dh dean aa rana 9 List of Illustrations 1 EH8100 Series Enclosure Rear View narta ian atan I RR a tad 5 2 EH8100 Series Enclos re WiringDiagram sviene ela A ean ne ele ie Ri 5 Br IMEI let Re NT A IR A ISS a athe 10 2 C1407M H 1 07 Important Safety Instructions 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Refer all servicing to qualified service personnel Servicing is required when the apparat
3. ating Temperature 40 to 122 F 40 to 50 C with heater Vibration 5 to 60 Hz with 0 082 inch total travel 15 g s at 60 Hz From 60 to 1 000 Hz 5 g s rms with random vibration Altitude Sea level to equivalent of 10 000 feet 3 048 m Acoustic Noise Operates in 150 dB acoustic noise environments Humidity Up to 100 relative humidity Equipped with standard Schraeder and pressure relief valves to provide positive internal pressure with dry nitrogen Ratings Meets NEMA Type 6 IP 67 standards Design and product specifications subject to change without notice IL QH Es i E 2 00 1 4 20 NUT PRESS 2X 5 08 F 6 00 6 00 A B c D E F G EH8104 18 00 450 5 50 1250 17 00 3 00 0 92 45 72 11 43 13 97 31 57 43 18 7 62 2 33 cusios 2200 650 7 00 13 00 20 00 7 00 088 55 88 16 51 17 78 33 02 50 80 17 78 2 23 NOTE VALUES IN PARENTHESES ARE CENTIMETERS ALL OTHERS ARE INCHES Figure 3 Dimensions C1407M H 1 07 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in materia workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below e Five years on FR FT FS Series fiber optic products and TW3000 Series unshielded twis pair transmission products hree years o
4. e Servicing section for instructions on how to disassemble reassemble and charge the enclosure ACCESSORIES EH8000RKIT Dry nitrogen recharging kit for EH8100 Series Kit includes pressure regulator and nitrogen PSKIT8100 Pressure sensor kit with contact closure that can be wired to trigger an alarm if enclosure s internal pressure falls below 5 psi C1407M H 1 07 7 Servicing DISASSEMBLY 1 Disconnect the power from the enclosure 2 Remove the mating connector from the rear of the enclosure by turning the outer ring counterclockwise until a click is felt then pull the mating portion of the connector off You may elect to remove the enclosure from its mount which will make the disassembly process much easier 3 Remove the center cap from the Schraeder valve Refer to Figure 1 4 Relieve internal enclosure pressure by depressing and holding down the center stem of the Schraeder valve A CAUTION Pressure must be released prior to opening the enclosure or personal injury may result 5 Remove the rear plate of the enclosure Refer to Figure 1 and do the following a Remove the spiral retaining ring from the back of the enclosure Use a screwdriver to pry the end of the spiral retaining ring from the retaining ring groove b Pull on the T handle to remove the rear plate from the housing RECHARGING AND REASSEMBLY Whenever the enclosure is disassembled for servicing it should be recharged after reassembly and prior to in
5. ed Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to Pelco 3500 Pelco Way Clovis CA 93612 5699 USA If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco c o Expeditors 473 Eccles Avenue South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 Green The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002 95 EC This equipment contains electrical or electronic components
6. g ring 8 Pressurize the inside of the enclosure and assemble the mating connector Refer to the sections Recharging and Reassembly and Mating Connector Assembly C1407M H 1 07 SCHRAEDER RETAINING SPRING PRESSURE END RELIEF VALVE GROUND STUD SPIRAL RETAINING SPRING HTR HTR ADI FOCUS Y f 12 Y PP COM DD E PP ZOOM PP 5V TABLEA FUNCTION COLOR VIDEO COAX CORE COAX SHIELD PP_ 5V BLK WHT RED WHT CAMERA AC LINE BLU CAMERA_AC NEUT VIO PS_SWITCH GRN WHT AC LINE BLK PS SWITCH WHT GRN IRIS BRN al NOTES j Consult the manual section dealing with model number listings for the wattage and number of heaters for the particular model that you are using Terminal block only on the EH8106 The EH8104 does not have a terminal block for lens presets Focus I V ZOOM IRIS va z z m jx le z lojn m Jo jo fo gt FOCUS RED ZOOM ORG LENS COM YEL AC NEUTRAL WHT PP FOCUS YEL WHT PP ZOOM GRY WHT Figure 2 EH8100 Series Enclosure Wiring Diagram C1407M H 1 07 MATING CONNECTOR ASSEMBLY To assemble the 16 pin mating connector perform the following steps 1 Discard the white plast
7. h nitrogen 1 Open the tank valve of the charging kit 2 Remove the cap from the enclosure s Schraeder valve and then attach the air chuck from the charging equipment to the valve 3 To reduce the purge time necessary to remove air from the enclosure position the enclosure so that the window is pointing up 4 Remove the plastic cap on the pressure relief valve on the rear of the enclosure Use a small screwdriver and hold the valve open Allow the nitrogen to flow through the enclosure until the humidity indicator registers the lowest humidity level changing color from pink to blue The humidity indicator can be viewed through the front window of the enclosure looking at the inside top of the enclosure Once the humidity indicator registers the lowest level remove the screwdriver and allow nitrogen to continue to flow into the enclosure until you no longer hear the flow of nitrogen from the tank to the enclosure 5 Remove the charging equipment air chuck from the Schraeder valve Replace the Schraeder valve and pressure relief valve caps POWER CONNECTION 1 Connect ground wire to the ground stud on the back of the enclosure 2 Connect the mating connector to the rear of the enclosure Operation The heaters are thermostatically controlled to come on at 40 F 4 C and go off at 60 F 16 C Maintenance At a minimum the enclosure should be recharged once a year Also recharge the enclosure after opening for servicing See th
8. hall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product lia bility relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when return
9. ic sleeve that is included with the connector assembly Thread the cable through the compression nut strain relief and connector shell CONNECTOR SHELL COMPRESSION NUT AND STRAIN RELIEF 2 Prepare the cabling by doing the following Control Cable a Strip the outer jacket back 2 inches 5 cm b Strip the individual conductors back 1 4 inch 6 mm and thread them into the appropriate holes through the rubber grommet Refer to Figure 2 RUBBER 4 Solder the individual conductors to the appropriate pins in the back of the connector refer to Figure 2 Push the rubber grommet into the back of the connector BACK OF CONNECTOR 5 Screw the connector shell to the back of the connector and tighten Tighten the compression nut strain relief as far as possible to compress the sealing ring inside the shell Attach the cable clamps to the compression nut strain relief THREADED END COMPRESSION NUT AND STRAIN RELIEF CABLE CLAMP THREADED END C1407M H 1 07 RECHARGING THE ENCLOSURE You may use your own charging equipment or Pelco s EH8000RKIT to recharge the enclosure If you are using your own equipment adjust the regulator for an output pressure of 12 psi 83 kPa If you are using the EH8000RKIT it uses a regulator with a fixed nonadjustable output pressure of 12 psi 83 kPa The gauge reads the tank pressure only Refer to Figure 1 and do the following to pressurize the inside of the enclosure wit
10. ional for heaters 40 watts EH8104 80 watts EH8106 16 pin receptacle with jam nut MS type connector supplied EH8104 4 477 ft 1365 m 2 821 ft 860 m 1 773 ft 540 m 16 449 ft 5 014 m 10 364 ft 3 159 m 6 514 ft 1 985 m EH8106 2 238 ft 682 m 1 410 ft 430 m 1 252 1 040 316 8 224 ft 2 507 m 5 182 ft 1 579 m 3 257 ft 993 m Heater EH8104 Two 20 watts each 120 VAC EH8106 Two 40 watts each 120 VAC Heaters are thermostatically controlled to come on at 40 F 4 C and go off at 60 F 16 C General Construction Aluminum 6061 T6 Finish Outside Gray polyester powder coat Inside Black anodized Dimensions See Figure 3 Front Window EH8104 4 inch diameter tempered glass 0 225 inch thick EH8106 6 inch diameter tempered glass 0 225 inch thick Camera Mounting Multiple mounting holes on camera sled allow for linear adjustment Maximum Camera Lens Size EH8104 3 inch diameter x 14 inch length 8 x 35 cm or 14 L x 2 5 W x 2 5 H inches 35 x 6 x 6 cm EH8106 5 inch diameter x 18 inch length 13 x 46 cm or 18 L x 4 0 W x 4 0 H inches 46 x 10 x 10 cm Enclosure Mounting Adjustable cradle secured with type 316 stainless steel bands Purge Fitting Standard Schraeder valve to allow enclosure to be filled with dry nitrogen Purge Fitting Prevents over pressurization of enclosure Weight EH8104 8 lb 4 kg EH8106 15 lb 7 kg C1407M H 1 07 Environmental Ambient Oper
11. n Spectra IV products hree years on Genex Series products multiplexers server and keyboard hree years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty hree years on PMCL200 300 400 Series LCD monitors wo years on standard motorized or fixed focal length lenses wo years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products Two years on Spectra Ill Esprit ExSite and PS20 scanners including when used in ontinuous motion applications Two years on Esprit and WW5700 Series window wiper excluding wiper blades Two years except lamp and color wheel on Digital Light Processing DLP displays he lamp and color wheel will be covered for a period of 90 days The air filter is not covered under warranty Eighteen months on DX Series digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video products One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair s
12. os and updated warranty and return information C1407M F 11 04 Factory preset for regulator changed to 12 psi per ECO 04 9807 Removed references to EH8108 and updated layout C1407M G 12 04 Revised instructions and artwork for mating connector assembly per ECO 04 10254 C1407M H 07 Updated for WEEE and RoHS compliance Revised specifications section for maximum cable distances and updated Accessories listing and O ring part numbers Pelco the Pelco logo Camclosure Esprit Genex Legacy and Spectra are registered trademarks of Pelco Endura ExSite and Spectra Ill are trademarks of Pelco DLP is a registered trademark of Texas Instruments Inc Copyright 2007 Pelco All rights reserved PELCO Worldwide Headquarters 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1509001 Australia Canada Finland France Italy Russia Singapore Spain Sweden The Netherlands United Arab Emirates United Kingdom United States
13. stallation Recharging requires the use of a Pelco EH8000RKIT recharge kit or equivalent and applicable O ring kit To prepare the enclosure for recharging follow the steps below 1 Once the enclosure has been disassembled remove the O ring from the rear plate and install a new O ring in the O ring groove in the rear plate 2 When the new O ring has been installed in the rear plate smear a liberal amount of the O ring lubricant provided with the kit on the exterior surface of the O ring and rear plate Replace the desiccant bag in the enclosure with a new one provided with the kit 3 Slide the camera sled back into the body making sure the front lip of the sled is under the retaining bracket of the enclosure When fully installed the rear plate will fit firmly into the rear opening of the housing and the retaining groove will be fully visible 4 Reinstall the spiral retaining ring in the retaining groove in the rear of the enclosure 5 Recharge the enclosure Refer to the section Recharging The Enclosure for instructions Replacement O rings Part Description ZH69 0205 2404 O ring for EH8104 enclosure EH800610006 O ring for EH8106 enclosure 8 C1407M H 1 07 Specifications Electrical Input Voltage Power Requirements Connector Mating Connector Maximum Cable Distances 120 VAC 16 AWG 1 5 mm 18 AWG 1 0 mm 20 AWG 0 5 mm 230 VAC 16 AWG 1 5 mm 18 AWG 1 0 mm 20 AWG 0 5 mm 120 VAC 230 VAC opt
14. tt heaters EH8106 6 inch diameter 20 inch length two 40 watt heaters Installation MOUNTING The enclosure can be mounted to a wall mount ceiling pedestal mount or pan tilt mounted to a wall or ceiling For proper installation refer to the instructions supplied with the mount The enc supplied losure should be attached to the mount or pan tilt by a minimum of two 1 4 20 fasteners not CAMERA AND LENS INSTALLATION To install the camera and lens perform the following steps 1 Remove the rear plate of the enclosure Refer to Figure 1 and do the following a Remove the spiral retaining ring from the back of the enclosure Use a screwdriver to pry the end of the spiral retaining ring from the retaining ring groove b Pull on the T handle to remove the rear plate from the housing 2 Slide the sled out of the enclosure 3 Remove the desiccant bag from the camera 4 Mount the camera and lens onto the sled sled Do not discard the bag a Extend the lens to the maximum length before positioning the camera and lens b Position the camera and lens so that they do not extend beyond the track c Fasten the camera and lens to the sled Fastener is not supplied 5 Connect wiring for camera power lens func 6 Unwrap and install the desiccant bag inside 7 Reinstall the camera sled by sliding it back i ions and video Refer to Figure 2 the enclosure nto the enclosure body Secure with the spiral retainin
15. us has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 6 Unless the unit is specifically marked as a NEMA Type 3 3R 3S 4 4X 6 or 6P enclosure it is designed for indoor use only and it must not be installed where exposed to rain and moisture 7 Use only installation methods and materials capable of supporting four times the maximum specified load 8 Only use replacement parts recommended by Pelco 9 After replacement repair of this unit s electrical components conduct a resistance measurement between the line and exposed parts to verify the exposed parts have not been connected to the line circuitry The product and or manual may bear the following marks A This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit RISK OF ELECTRIC SHOCK A This symbol indicates that there are important operating and maintenance instructions in DO NOT OPEN the literature accompanying this unit CAUTION C1407M H 1 07 3 Description Enclosures in the EH8100 Series are sealed and p ressurized They will accept CCD cameras with fixed focal length or motorized zoom lenses The enclosures are wired for lenses with preset capabilities MODELS EH8104 4 inch diameter 17 inch length two 20 wa
Download Pdf Manuals
Related Search