Paxton Automotive Fan 4PFX020-080 User's Manual
Contents
1. 4 a Install and tighten the supplied plastic ratchet clamps on all hose connections Remove the reservoir cap and fill system with 25 75 coolant water mix Make sure that all wires and hoses are routed away from hot moving or sharp objects Key on and verify coolant circulation through the system Check for leaks If supercharger boost is increased a larg er bypass valve may be required to reduce compressor surge NOTE Some of the supplied fittings and hoses may not be used Take special care not to kink the hoses by using the ones that best fit your application SUPERCHARGERS Paxton Automotive 1300 Beacon Place Oxnard CA 93033 805 604 1336 FAX 805 604 1337 DP N 4PFX020 080 v1 0 06 03 082. 2 5WO01 054 16 GA FUSE HOLDER 1 5W014 030 14GA STRD WIRE BLACK 4 7E010 075 12 X 3 4 SHT METL SCRW HEX 1 7R003 027 ADEL CLAMP 1 11 16 1 8F001 402 PUMP WATER PIERBURG 1 8N006 010 WATER COOLER 1 4PFX020 080 MANUAL CAC UPGRADE 1 3863515 DECAL PAXTON COLOR 9 X3 1 OPTIONAL 8N150 010 UNIVERSAL BATT RELOCAT ASSY 1 4GJ012 230 8 DISCHARGE TUBE WITH RACE VALVE FLANGE SATIN POLISHED 8D204 011 8 RACE BLOWOFF VALVE SATIN POLISHED P N 4PFX020 080 2008 Paxton Automotive All Rights Reserved Intl Copr Secured vi 03JUN08 v1 0 4PFX020 080 v1 0 Section 1 Component Removal 1 Component Removal A Disconnect and remove the battery from vehicle It will need to be relocated to the trunk using a battery relocation kit See Fig 1 a Follow the instructions supplied with the battery relocation kit of your choice Paxton 8N150 010 may be used B Remove the supercharger discharge tube and carburetor enclosure inlet elbow P N 4PFX020 080 v1 0 2008 Paxton Automotive All Rights Reserved Intl Copr Secured 03JUNOS v1 0 4PFX020 080 v1 0 Section 2 Charge Air Cooler Install 2 Charge Air Cooler Install A original supercharger discharge tube so that a 12 inch section of straight tubing with the bypass valve bung remains See Fig 2 a Fig 2 a B 2 4 off of the straight section of the carburetor enclosure inlet elbow See Fig 2 b De bur a
3. AE and Metric Allen Wrenches SAE Flat 2 Screwdriver Phillips 2 Screwdriver Wire Cutters Strippers and Crimpers Tape Measure Pipe Tape Teflon Adjustable Wrench 1 Hole Saw 3 8 Drive and Socket Set SAE and Metric Hacksaw Hose Cutters P N 4PFX020 080 v1 0 2008 Paxton Automotive All Rights Reserved Intl Copr Secured V 03JUN08 v1 0 4PFX020 080 v1 0 SMALL BLOCK FORD CHARGE COOLER UPGRADE Part No 8PN301 080 8 SATIN POLISHED PARTS LIST IMPORTANT Before beginning installation verify that all parts are included in the kit Report any shortages or damaged parts immediately PART DESCRIPTION QTY 8PN101 080 8 CAC CORE ASSY SBF CARB 1 8PN104 080 CAC SPT COMPONENTS SBF CARB 1 7P375 075 3 4 HOSE UNION 3 7P500 026 1 2NPT X 3 4 BARB 90 BRASS 3 7 500 750 1 2 NPT TO 3 4 HOSE BARB 90 SHORT 1 7PS275 200 SLEEVE BLACK 2 7510 X 2 0 1 7R002 044 44 SAE TYPE SS HOSE CLAMP 2 7R007 001 RATCHET CLAMP 1 1 8 14 7U038 000 3 4 HEATER HOSE 10 7U038 012 HOSE 3 4 DIA 90DEG 4X12 3 7U038 150 HOSE 3 4 X150 MOLDED HOSE 2 8N100 001 NYLON MOUNTING KIT 2 7U100 055 TIE WRAP 7 5 NYLON 5 70100 044 TIE WRAP 4 NYLON 5 8N105 010 WATER TANK W FTG 5 0 MUST 1 7P500 026 1 2NPT X 3 4 BARB 90 BRASS 2 8PN107 080 ASSY WATER PUMP SBF CARB CAC 1 5W001 005 3 8 PLASTIC WIRE LOOM 4 5W001 011 16 14 GA RING TERM 26 HOLE 2 5W001 013 14 16 GA BUTT CONN BLU INSUL
4. Ode Ra RU ii TABLE OF CONTENTS RAO ORC UE a A RR ER TU a iii NOTICES uat ics koe OX aei Cx FE C OLOR deoa RR Casi ed eh ned wee d DR C n iv TOOLS amp SUPPLY REQUIREMENTS 244 cs che or aratro ER D V PARTS LIST SMALL BLOCK FORD CHARGE COOLER UPGRADE vi 1 COMPONENT REMUVAL DEOR i Di E DRS a D d i c iC 1 2 CHARGE AIR COOLER INSTALLATION seseeeeee RI n nn 2 3 CAC WATER COOLER eee hn nnn 3 4 WATER RESERVIOR ASSEMBLY 4 5 WATER PUMP WIRING E qr QR MR ae Da ha oe E a 5 6 PLUMBING AND BLEEDING SYSTEM n RR ROT A ea 6 P N 4PFX020 080 v1 0 2008 Paxton Automotive All Rights Reserved Intl Copr Secured iii 03JUNOB v1 0 4PFX020 080 v1 0 NOTICES Read before installation is started Removal of the factory sealed pulley will reduce the supercharger warranty from three years to one year unless the supercharger unit with the original pulley still attached and new pulley are sent into Paxton for removal installation and re sealing If the supercharger warranty is not a concern or if the supercharger warranty has expired the pulley may simply be removed and replaced Hammering prying etc on the supercharger and or pulley will cause damage to the parts Light heating of the supercharger pulley with a propane torch if the
5. Owner s Installation Guide for the Paxton Automotive Charge Cooler Upgrade for Driver Side Supercharger Mount Small Block Ford Carbureted Legal in California only for racing vehicles which may never be used upon a highway Paxton Automotive 1300 Beacon Place Oxnard CA 93033 805 604 1336 FAX 805 604 1337 DP N 4PFX020 080 v1 0 03 24 08 FOREWORD Important This charge cooler upgrade is for driver side supercharger mount vehicles only Paxton does not make a charge cooler upgrade for passenger side supercharger mount vehicles of the Paxton supercharger kit expressly designed for this vehicle All infor mation illustrations and specifications contained herein are based on the lat est product information available at the time of this publication Changes to the manual may be made at any time without notice Contact Paxton Automotive for any additional information regarding this kit and any of these modifications at 888 9 PAXTON 8 00am 4 30pm PST T manual provides information on the installation maintenance and service Take note of the following before proceeding 1 Proper installation of this supercharger kit requires general automotive mechanic knowledge and experience Please browse through each step of this instruction manual prior to beginning the installation to determine if you should refer the job to a professional installer technician Please contact your dealer or Paxton Automotive for possible installe
6. e battery tray Modify tray as needed to eliminate sharp edges from puncturing the reservoir See Fig 4 a Fig 4 a Secure the reservior using the original battery hold down clamp or other suitable method Water Pump Wiring 5 Water Pump Wiring A Locate the supplied electric water pump on the passenger side frame rail so that the supplied 150 hose elbow connects the bottom fitting in the reservoir to the inlet center barb on the pump B Install the supplied eyelet onto the ground brown wire of the water pump Ground the water pump using the sheet metal screw in the next step C Using the supplied adel clamp secure the water pump by drilling the frame rail and installing the supplied sheet metal screw See Fig 5 a Fig 5 a D Route the water pump power wire to a keyed power source and attach using the supplied fuse holder and butt connectors Plumbing and Bleeding System 6 Plumbing and Bleeding System A Connect the water pump discharge to the water cooler using the supplied hose hose elbow and hose mender The hoses will need to travel through holes must be drilled or under the radiator core support Connect the open fitting on the water cooler to the bottom fitting on the charge cooler using the sup plied hose and two hose elbows and hose menders if needed for smooth routing Connect the top fitting on the CAC to the upper fitting on the reservoir using a 90 hose elbow See Fig
7. ly affect the break in period so long as factory break in procedures are followed For best performance and continued durability please take note of the following key points 1 Use only premium grade fuel 91 octane or higher R M 2 2 The engine must have stock or lower than stock compression ratio 3 Always listen for any sign of detonation pinging and discontinue hard use no boost until problem is resolved 4 Perform an oil and filter change upon completion of this installation and prior to operating the vehicle Thereafter always use a high grade SF rated engine oil or a high quality synthetic and change the oil and filter every 3000 miles This product may not be legal for use on public roads in all 50 states P N 4PFX020 080 2008 Paxton Automotive All Rights Reserved Intl Copr Secured iv 03JUN08 v1 0 4PFX020 080 v1 0 PAXTON CHARGE COOLER Installation Instructions Before beginning this installation please read through this entire instruction booklet This Paxton Charge Cooler system was designed as a street strip oriented charge cooler As with any power enhancing product this system is intended for use on healthy well maintained engines Paxton Automotive is not responsible for engine damage Installation on new engines will not harm or adversely affect the break in period so long as factory break in procedures are followed TOOL amp SUPPLY REQUIREMENTS Open End Wrenches S
8. nd clean both ducts Fig 2 b C Re install both ducts and use the supplied sleeve to connect the discharge duct to the charge air cooler CAC inlet Tighten hose clamps on all sleeves Install 90 fittings into the CAC so that they point towards the front of the vehicle One of these fittings needs to be the supplied short fittings in order to allow it to be installed without hitting the other fitting See Fig 2 c Fig 2 c Attach to tubes using 2 3 4 sleeve and 44 clamps Close hood and verify CAC clearance If interference occurs loosen clamps and lower CAC as needed CAC Water Cooler Installation 3 CAC Water Cooler Installation A Using pipe thread sealant install a 90 fitting into each end of the supplied water cooler so that they point in the same direction B Temporarily remove the passenger side horn to allow access to the front of the radiator C Use the supplied 8N100 001 Nylon Mounting Kit to attach the water cooler to the front of the vehicle s radiator Make sure to place the supplied foam spacers between the radiator and the water cooler See Fig 3 a Section 4 Water Reservoir Assembly 4 Water Reservoir Assembly Installation A B Install a 1 2 NPT 90 hose barb fitting in the side of the supplied water reservoir so that it points up Install a 1 2 NPT 90 hose barb into the bottom hole of the reservoir pointing down Test fit the reservoir in th
9. pulley is tight on the shaft will aid removal A return authorization number is required before the supercharger and pulley are sent into Paxton Call the Paxton service department at 805 487 3796 for a return authorization number Return freight ground will be paid by Paxton This product is protected by state common law copyright and or patent All legal rights therein are reserved The design layout dimensions geometry and engineering features shown in this product are the exclusive property of Paxton Automotive This product may not be copied or duplicated in whole or part abstractly or fundamentally intentionally or fortuitously nor shall any design dimension or other information be incorporated into any product or apparatus without prior written consent of Paxton Automotive PLEASE READ CAREFULLY This kit should only be installed by qualified mechanics It is imperative that the correct air fuel mixture be maintained at all times This Kit is to be supplied to competent engine tuners for their completion by the addition of custom tuning The installation of this system without custom tuning to compensate for boost pressure will cause engine damage This product is intended for use on healthy well maintained engines Installation on a worn out or damaged engine is not recommended and may result in failure of the engine Paxton Automotive is not responsible for engine damage Installation on new engines will not harm or adverse
10. rs in your area 2 This product was designed for use on stock un modified OEM vehicles The PCM computer engine transmission drive axle ratios and tire O D must be stock If the vehicle or engine has been modified in any way check with Paxton prior to installation and use of this product 3 Use only premium grade fuel with a minimum of 91 octane R M 2 4 Always listen for any sign of detonation knocking pinging and discontinue hard use no boost until problem is resolved 5 Paxton is not responsible for any clutch transmission drive line or engine dam age FAEERE from Paxton warranty coverage considerations include but not imited to 1 Neglect abuse lack of maintenance abnormal operation or improper installa tion 2 Continued operation with an impaired vehicle or sub system 3 The combined use of Paxton components with other modifications such as but not limited to exhaust headers aftermarket camshafts nitrous oxide third party PCM programming or other such changes o 2008 PAXTON AUTOMOTIVE All rights reserved No part of this publication may be reproduced transmitted transcribed or translated into another language in any form by any means without written permission of Paxton Automotive P N 4PFX020 080 2008 Paxton Automotive All Rights Reserved Intl Copr Secured ii 03JUNOS v1 0 4PFX020 080 v1 0 TABLE OF CONTENTS FOREWORD ccc et ei ede RO Re CA ee he eee CC OE RR RA E
Download Pdf Manuals
Related Search