Home

Panasonic WV-CF344 Operating Instructions

1. 23 17 Chroma level adjustment CHROMA GAIN 23 18 Aperture level adjustment AP GAIN 23 19 Pedestal level adjustment PEDESTAL 23 20 Chroma phase hue adjustment HUE 23 21 Pixel compensation PIX OFF 23 22 Communication setting COMMUNICATION CP310 CP310 CP300 CP310 CP310 CP300 24 23 Default resetting CAMERA RESET 24 24 Serial number viewing SER NO 24 Camera language selection LANGUAGE SETUP 25 Shortcut operation 26 4 Setup item Description CAMERA ID This item specifies the camera title The camera title that indicates the camera location and other information about the camera is created with alphanumeric characters and symbol and then displayed on the screen CAMERA Performs the camera operation settings SCENE 1 SCENE 2 Selects a scene file It is possible to register and save the settings as a scene file in case that it is necessary to change the settings such when shooting at night ALC ELC Selects the method of controlling the quantity of light in accordance with the lens to be used SHUTTER Specifies the electronic shutter speed AGC Specifies gain adjustment SENS UP Specifies electronic sensitivity
2. CAMERA SETUP SCENE1 ALC ELC ALC SHUTTER OFF AGC ON HIGH SENS UP OFF WHITE BAL ATW1 DNR HIGH AUTO1 VMD OFF RET TOP END D amp N IR 13 Step 6 Hold down the SET button for more than 2 seconds after completion of masking Return to the previous menu Step 7 Move the cursor to LEVEL and press the RigHT or LEfT button to adjust the level 3 Electronic shutter setting SHUTTER The variation in shutter speed allows users to perform the following Increased shutter speed prevents blurring fast moving subjects If flicker is observed under fluorescent lighting of 50 Hz selection of 1 100 for the speed can reduce flicker The shutter speed is selectable from the following OFF 1 60 default 1 100 1 250 1 500 1 1000 1 2000 1 4000 1 10000 1 120000 Note When ALC ELC is set to ELC or ALC appears and the shutter function cannot be activated 4 Gain control setting AGC Select a gain control setting from the following ON HIGH default ON MID ON LOW Automatically increases the gain to make the screen brighter when the illuminance of the subject becomes darker HIGH MID and LOW indicate the gain level OFF Does not increase the gain Note When SENS UP is set to the AUTO mode AGC cannot be set to OFF 5 Electronic sensitivity enhancement setting SENS UP Use of the electronic sensitivity enhancement funct
3. RIGHT or LEFT button and enter a correct character To enter a blank move the cursor to SPACE and press the SET button To delete all the entered characters move the cursor to RESET and press the SET button Step 3 Move the cursor to POSI and press the SET button after title entered The display positioning screen appears Step 4 Press the UP DOWN RIGHT and LEFT buttons to decide the title position and press the SET button The title position is specified FLOOR 1 Editing area Top screen CAMERA ID screen Display positioning screen MODEL WV CP310 SERIES CAMERA ID ON CAMERA SYSTEM SPECIAL LANGUAGE END SETUP ENABLE CAMERA ID 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ amp SPACE POSI RET TOP END RESET 11 Screen when SCENE1 is selected Screen when SCENE2 is selected CAMERA SETUP SCENE1 ALC ELC ALC SHUTTER OFF AGC ON HIGH SENS UP OFF WHITE BAL ATW1 DNR HIGH AUTO1 VMD OFF RET TOP END D amp N IR CAMERA SETUP SCENE2 COPY SCENE1 ALC ELC ALC SHUTTER OFF AGC ON HIGH SENS UP OFF WHITE BAL ATW1 DNR HIGH AUTO1 VMD OFF RET TOP END D amp N IR Scene file number ALC CONT 1 BACK LIGHT COMP SYSTEM SETUP screen OFF ABS MASK SET LEVEL I 0 RET TOP END BLC ON Camera operation setting CAMERA SETUP The following describes the
4. SET button The flaw is corrected and the pixel compensation point is registered The PIX OFF screen appears again An asterisk is attached at the right side of the number when registration is completed The coordinate is expressed in figures Note To clear the registered pixel compensation point move the cursor to 1 of the right of DEL use the RIGHT and LEFT buttons to select the number with which the target pixel compensation point is registered and press the SET button The registered pixel compensation point is cleared and an asterisk at the right side of the number disappears 22 Communication setting COMMUNICATION CP310 CP310 CP300 CP310 CP310 CP300 The required communication configuration is performed to use this unit integrated into the system with a receiver COAX RCV When using our receiver e g WV RC150 COAX default When not using any receiver 23 Default resetting CAMERA RESET The settings in the setup menu are restored to the default settings Move the cursor to PUSH SET of CAMERA RESET and hold down the SET button for more than 2 seconds to enter the RESET screen To return to the previous screen without resetting move the cursor to NO and press the SET button To restore the default settings move the cursor to YES and press the SET button Note The data of the registered pixel compensation points
5. amp SPACE POSI RET TOP END RESET SYSTEM SETUP SYNC INT PRIVACY ZONE OFF STABILIZER OFF EL ZOOM OFF UPSIDE DOWN OFF LDC I 0 RET TOP END SPECIAL SETUP CHROMA GAIN I 160 AP GAIN I 32 PEDESTAL I 15 PIX OFF CAMERA RESET PUSH SET SER NO XXXXXXXX RET TOP END CAMERA SETUP SCENE1 ALC ELC ALC SHUTTER OFF AGC ON HIGH SENS UP OFF WHITE BAL ATW1 DNR HIGH OFF VMD OFF RET TOP END D amp N ELE HUE I 0 10 Camera title setting CAMERA ID This item specified the camera title The camera title that indicates the camera location and other information about the camera is created with alphanumerics and symbols and is displayed on the screen The camera title is named with up to 16 characters Follow the procedure below to specify the camera title Step 1 Select ON for CAMERA ID and then press the SET button The CAMERA ID screen appears Important When CAMERA ID is set to OFF the camera title does not appear even after setting the camera title Step 2 Move the cursor to the target item with use of the UP DOWN RIGHT and LEFT buttons and press the SET button to enter the character The entered characters are displayed in the editing area lt Character entry gt To revise a character move the arrow in the editing area to a wrong character with use of the
6. buttons to select ON or OFF ON Outputs alarm signal when in display mode Actions may be confirmed through the motion detection mode when a moving object is detected OFF default Does not output alarm signal when in display mode Step 5 Move the cursor to DISPLAY MODE and press the SET button The display mode screen appears If a moving object is detected in the set area the area will be reversely highlighted Hold down the SET button for more than 2 seconds to return MOTION DET 1 RET TOP END LEVEL 2S OFF DWELL TIME DISPLAY MODE ALARM MASK SET I 20 Display mode screen MOTION DET screen Step 6 Move the cursor to LEVEL and press the RIGHT or LEFT button to adjust the level Repeat step 5 and 6 to adjust to optimal level Step 7 Move the cursor to DWELL TIME and select the dwell time from the following unit seconds 2S default 5S 10S 30S Alarm signal will be issued once a continuously moving object is detected within the specified time Setting of scene change detection This function detects a change in the subject state that occurs by covering the camera with a cloth a cap or others or by changing the camera direction largely Follow the procedure below Step 1 Move the cursor to VMD and press the RIGHT or LEFT button to select SCENE CHANGE CAMERA SETUP screen VMD SCENE CHANGE CAMERA SETUP
7. select the zone number and repeat from step 3 12 Image stabilizer setting STABILIZER Whether or not to enable the image stabilizer is determined This function is effective for the case that the camera is installed at a place with slight shaking ON Enables the image stabilizer OFF default Disables the image stabilizer Important When ON is selected for the image stabilizer the view angle becomes narrower and the resolution becomes lower When ON is selected for the image stabilizer check the view angle and resolution at camera installation The image stabilizer function may not work for the following subjects or conditions Dark subject Less contrasty subject e g white wall Subject shaking at excessive speed Large amplitude image shaking 13 Electronic zoom setting EL ZOOM Whether or not to use the electronic zoom is determined ON Uses the electronic zoom OFF default Does not use the electronic zoom When ON is selected the zoom factor and the panning tilting settings can be configured Follow the procedure below EL ZOOM EL ZOOM EL ZOOM PUSH SET PUSH SET ZOOM PAN TILT PUSH SET PUSH SET ZOOM PAN TILT PUSH SET PUSH SET ZOOM PAN TILT U ZOOM D U TILT D L PAN R SYSTEM SETUP screen EL ZOOM screen Pan tilt setting screen Zoom setting screen RET TOP END RET TOP END RET TOP END OFF SYSTEM SETUP SYNC IN
8. CP314 CP310 CP310 CP300 The functions with this notation are available when using the model WV CP300 and WV CP304 CF354 The functions with this notation are available when using the model WV CF354 CF344 The functions with this notation are available when using the model WV CF344 3 Contents Preface 2 About the user manuals 2 Trademarks and registered trademarks 2 About notations 2 About the setup menus 4 List of setup menu 4 Basic operation 5 Screen transition diagram CP310 CP310 CP300 6 Screen transition diagram CP310 CP310 CP300 7 Screen transition diagram CF354 8 Screen transition diagram CF344 9 Camera title setting CAMERA ID 10 Camera operation setting CAMERA SETUP 11 1 Register a scene file SCENE1 SCENE2 11 2 Light quantity control method selection ALC ELC 11 B
9. Focus setting FOCUS CF354 Sets the focus adjustment method and performs fine adjustment Follow the procedure below Important When focus missing occurs due to secular change in the lens and installation environment or peripheral temperature change the focus adjustment is required again Step 1 Move the cursor to ABF PUSH of FOCUS and press the SET button The focus function provides focus adjustment to automatically focus on a subject located in the center of the screen Step 2 To fine adjust the focus select MANUAL of FOCUS press the SET button and press the RIGHT or LEFT button to adjust the focus manually 22 Important The following are recommendation for focus setting in accordance with subjects For such case subject conditions Select this recommendation Normal subject ABF Frequently moving subject Fine adjustment with MANUAL setting after ABF Subject with large illuminance change Subject with low illuminance Too bright or reflective subject Subject through a window Place where the lens easily becomes dirty Subject with less contrast such as white wall Subject with remarkable depth Subject with heavy flicker Subject with horizontally parallel lines such as a shutter 23 Special menu setting SPECIAL SETUP The special menu setup is performed including the setting of the camera
10. HIGH SENS UP OFF WHITE BAL ATW1 DNR HIGH OFF VMD OFF RET TOP END D amp N ELE HUE I 0 8 Screen transition diagram CF354 Top screen CAMERA ID screen CAMERA SETUP screen SYSTEM SETUP screen SPECIAL SETUP screen LANGUAGE SETUP screen MODEL WV CF354 CAMERA ID OFF CAMERA SYSTEM SPECIAL LANGUAGE END SETUP DISABLE LANGUAGE SETUP LANGUAGE ENGLISH SET RET TOP END CAMERA ID 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ amp SPACE POSI RET TOP END RESET SYSTEM SETUP SYNC INT PRIVACY ZONE OFF STABILIZER OFF EL ZOOM OFF UPSIDE DOWN OFF LDC I 0 RET TOP END SPECIAL SETUP CHROMA GAIN I 160 AP GAIN I 32 PEDESTAL I 15 PIX OFF CAMERA RESET PUSH SET SER NO XXXXXXXX ABF PUSH FOCUS RET TOP END CAMERA SETUP SCENE1 ALC ELC ALC SHUTTER OFF AGC ON HIGH SENS UP OFF WHITE BAL ATW1 DNR HIGH OFF VMD OFF RET TOP END D amp N ELE HUE I 0 9 Screen transition diagram CF344 Top screen CAMERA ID screen CAMERA SETUP screen SYSTEM SETUP screen SPECIAL SETUP screen LANGUAGE SETUP screen MODEL WV CF344 CAMERA ID OFF CAMERA SYSTEM SPECIAL LANGUAGE END SETUP DISABLE LANGUAGE SETUP LANGUAGE ENGLISH SET RET TOP END CAMERA ID 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ
11. TOP END DEL ZONE LEVEL I 2 SYSTEM SETUP screen ZONE NUMBER screen ON 2 SYSTEM SETUP SYNC INT PRIVACY ZONE STABILIZER OFF EL ZOOM OFF UPSIDE DOWN OFF LDC I 0 RET TOP END Step 1 Move the cursor to PRIVACY ZONE select ON 1 or ON 2 and press the SET button The ZONE NUMBER screen appears Step 2 Move the cursor to the number at the right of the title and select the zone number using the RIGHT or LEFT button Step 3 Move the cursor to POSITION and press the SET button SYSTEM SETUP screen SYSTEM SETUP SYNC INT PRIVACY ZONE OFF STABILIZER OFF EL ZOOM OFF UPSIDE DOWN OFF LDC I 0 RET TOP END 20 Step 4 Press the UP DOWN RIGHT and LEFT buttons to determine the left upper position of the zone to be set and press the SET button Step 5 Press the UP DOWN RIGHT and LEFT buttons to determine the lower right position of the zone to be set and press the SET button An asterisk will be displayed after the number and the zone setting will be saved Step 6 When ON 2 is selected for PRIVACY ZONE the mosaic level may be adjusted The mosaic level may be set through ZONE LEVEL Range 1 to 4 Note To delete a zone select the zone number and press the SET button after moving the cursor to DEL To change the settings of a zone
12. area to detect white area of white balance is displayed full screen by default To change the white balance detection area start from step 4 Step 4 Move the cursor to POSITION and press the SET button Step 5 Press the UP DOWN RIGHT and LEFT buttons to move to the upper left part of the area to be set and press the SET button Step 6 Press the UP DOWN RIGHT and LEFT buttons to move to the lower right part of the area to be set and press the SET button 7 Digital noise reduction function setting DNR The digital noise reduction function reduces noise automatically under the condition of low illuminance The effect level of the noise reduction function is selectable from the following LOW Low level of noise reduction small residual image HIGH default High level of noise reduction large residual image 8 Black and white mode setting D amp N IR CP310 CP310 CP300 D amp N ELE CP310 CP310 CP300 CF354 CF344 The settings relating to the black and white mode can be configured Follow the procedure below AUTO1 D amp N IR 1 LEVELHIGH DURATION TIME S L BURST BW ON RET TOP END I CAMERA SETUP SCENE1 ALC ELC ALC SHUTTER OFF AGC ON HIGH SENS UP OFF WHITE BAL ATW1 DNR HIGH AUTO1 VMD OFF RET TOP END D amp N IR CAMERA SETUP screen D amp N IR screen Step 1 Move the cursor to D amp N IR and select th
13. camera operation settings The following settings can be configured on the CAMERA SETUP screen displayed from the top screen Refer to page 5 for how to call up the screen The settings configured on the CAMERA SETUP screen will be saved as a scene file 1 Register a scene file SCENE1 SCENE2 It is possible to register 2 patterns of scene file When different settings are to be applied between day and night SCENE1 can be applied in the daytime and SCENE2 at night Change between the scene files can be made by shortcut operation page 26 SCENE1 is set as the default setting Step 1 After confirming that SCENE1 is selected configure the settings of ALC ELC through VMD page 11 18 To change the scene files go to step 2 Step 2 Move the cursor to SCENE1 and press the RIghT or LEfT button to select SCENE2 The screen changes and displays SCENE2 Step 3 To configure the settings of SCENE2 using the settings of SCENE1 press the SET button after moving the cursor to COPY SCENE1 The settings of SCENE1 will be copied to SCENE2 Step 4 Edit the settings to be changed as the settings of SCENE2 The number displayed at the right side of the title on each setting screen indicates a scene file number Step 5 Move the cursor to SCENE2 and press the RIghT or LEfT button to select SCENE1 to resume normal
14. image quality and the communication configuration when a receiver is used The following settings are to be configured on the SPECIAL SETUP screen displayed from the top screen Refer to page 5 for how to call up the screen 17 Chroma level adjustment CHROMA GAIN Press the RIghT or LEfT button to adjust the color density of the camera image When the level indicator moves in the direction the color becomes deeper and when the level indicator moves in the direction the color becomes lighter Be sure to view a vector chromaticity indicator or a video monitor when the adjustment is performed 18 Aperture level adjustment AP GAIN Press the RIghT or LEfT button to adjust the image quality When the level indicator moves in the direction the image becomes sharper and when the level indicator moves in the direction the image becomes softer Be sure to view a video monitor when the adjustment is performed Note Moire interference fringes may be observed when shooting a subject with fine pattern such as a carpet or a curtain In such a case move the indicator in the direction to reduce moire 19 Pedestal level adjustment PEDESTAL Press the RIghT or LEfT button to adjust the pedestal level of the camera When the level indicator moves in the direction the image becomes brighter and when the level indicator moves in the direction the image becomes darker Be sure to view a wavefor
15. operation 2 Light quantity control method selection ALC ELC The method of controlling the quantity of light is selected from the following in accordance with the lens to be used ALC default The iris of the lens is automatically adjusted in accordance with the brightness of a subject Select ALC when using an ALC lens ALC Controls the quantity of light with a combination of the electronic shutter and auto iris This selection is suitable at shooting a bright subject such as an outdoor subject with auto iris lens Be aware that flicker may occur when a subject is under fluorescent lighting ELC Controls the quantity of light with the electronic shutter This selection is suitable for use of a lens with fixed iris or manual iris 12 Back light compensation function Follow the procedure below Step 1 Set ALC ELC to ALC and press the SET button The ALC CONT screen appears Note When ALC ELC is set to ELC or ALC and the SET button is pressed the ELC CONT or ALC CONT screen will appear Step 2 Move the cursor to BLC and select from the following options ON Automatically compensate when the background is brighter than the subject OFF default This mode is used when the area in front of the subject is extremely bright Step 3 Move the cursor to ABS and select from the following options ABS Auto Black Stretch Technology The latest d
16. the power after completing settings in the SETUP menu or after changing the camera view angle Motion detection is the detection function within the screen range for electronic zoom of 1x MOTION DET screen MOTION DET 1 RET TOP END LEVEL 2S OFF DWELL TIME DISPLAY MODE ALARM MASK SET I 20 CAMERA SETUP screen MOTION DET AUTO1 CAMERA SETUP SCENE1 ALC ELC ALC SHUTTER OFF AGC ON HIGH SENS UP OFF WHITE BAL ATW1 DNR HIGH VMD RET TOP END D amp N IR Setting of motion detection Move the cursor to VMD press the LEfT or RIghT button to select MOTION DET Step 1 Move the cursor to MOTION DET and press the SET button The MOTION DET screen appears Step 2 Move the cursor to MASK SET and press the SET button The mask setting screen appears MOTION DET screen Mask setting screen MOTION DET 1 RET TOP END LEVEL 2S OFF DWELL TIME DISPLAY MODE ALARM MASK SET I 20 In the masked area no alarm will be issued even if a moving object is detected The masked area is set in the same way as the masked area setting in Light quantity control method selection page 11 18 Step 3 Hold down the SET button for more than 2 seconds after completion of masking Return to the previous menu Step 4 Move the cursor to ALARM and press the LEFT and RIGHT
17. A ID 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ amp SPACE POSI RET TOP END RESET SYSTEM SETUP SYNC INT PRIVACY ZONE OFF STABILIZER OFF EL ZOOM OFF UPSIDE DOWN OFF LDC I 0 HUE I 0 RET TOP END SPECIAL SETUP CHROMA GAIN I 160 AP GAIN I 32 PEDESTAL I 15 PIX OFF CAMERA RESET PUSH SET SER NO XXXXXXXX COMMUNICATION COAX RET TOP END CAMERA SETUP SCENE1 ALC ELC ALC SHUTTER OFF AGC ON HIGH SENS UP OFF WHITE BAL ATW1 DNR HIGH AUTO1 VMD RET TOP END D amp N IR OFF 7 Screen transition diagram CP310 CP310 CP300 Top screen CAMERA ID screen CAMERA SETUP screen SYSTEM SETUP screen SPECIAL SETUP screen LANGUAGE SETUP screen MODEL WV CP300 SERIES CAMERA ID OFF CAMERA SYSTEM SPECIAL LANGUAGE END SETUP DISABLE LANGUAGE SETUP LANGUAGE ENGLISH SET RET TOP END CAMERA ID 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ amp SPACE POSI RET TOP END RESET SYSTEM SETUP SYNC INT PRIVACY ZONE OFF STABILIZER OFF EL ZOOM OFF UPSIDE DOWN OFF LDC I 0 RET TOP END SPECIAL SETUP CHROMA GAIN I 160 AP GAIN I 32 PEDESTAL I 15 PIX OFF CAMERA RESET PUSH SET SER NO XXXXXXXX COMMUNICATION COAX RET TOP END CAMERA SETUP SCENE1 ALC ELC ALC SHUTTER OFF AGC ON
18. Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use The model number is abbreviated in some descriptions in this manual Operating Instructions Color CCTV Camera Model No WV CP300 Series WV CF344 Series Lens is optional for WV CP300 Series WV CP300 WV CF344 This manual covers the models WV CP300 Series WV CP310 WV CP314 WV CP300 WV CP304 and WV CF344 Series WV CF354 WV CF344 2 Preface About the user manuals The operating instructions of the camera consist of 2 sets these operating instructions PDF and Installation Guide This document explains how to configue the settings of the camera Refer to the installation guide for further information about how to install the camera Adobe Reader is required to read PDF When the Adobe Reader is not installed on the PC download the latest Adobe Reader from the Adobe web site and install it Trademarks and registered trademarks Adobe Acrobat Reader and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countries About notations The following notations are used when describing the functions limited for specific models The functions without the notations are supported by all models CP310 CP310 CP300 The functions with this notation are available when using the model WV CP310 and WV
19. GUAGE Selects a language to be used in the setup menu About the setup menus Performing each setting item in the setup menu should be completed in advance to use this unit Perform the settings for each item in accordance with the conditions of the camera shooting area List of setup menu 5 Basic operation The operations in the setup menu are performed with the operation buttons after calling up the setup menu on the connected video monitor The description below explains how to operate the setup menu basically Screenshots of WV CP310 are shown as an example Screenshot 2 The setup mode changes to ENABLE and the setup menu becomes ready to be set Step 3 Move the cursor to the item to be set and press the SET button Screenshot 1 Hold down the SET button for about 2 seconds to call up the top screen of the setup menu Step 1 Press the UP or DOWN button to move the cursor to END Step 2 Press the RIGHT button to move the cursor to SETUP and press the SET button to change the setup mode from DISABLE to ENABLE MODEL WV CP310 SERIES CAMERA ID OFF CAMERA SYSTEM SPECIAL LANGUAGE END SETUP DISABIE MODEL WV CP310 SERIES CAMERA ID OFF CAMERA SYSTEM SPECIAL LANGUAGE END SETUP ENABLE Screenshot 3 The selected setup screen in the setup menu appears on the screen Note If the top screen of the setup menu is called up with the operation buttons w
20. SCENE1 ALC ELC ALC SHUTTER OFF AGC ON HIGH SENS UP OFF WHITE BAL ATW1 DNR HIGH AUTO1 RET TOP END D amp N IR 19 Camera system setting SYSTEM SETUP Performs the settings relating to the camera system such as synchronization and privacy zone The following settings can be configured on the SYSTEM SETUP screen displayed from the top screen Refer to page 5 for how to call up the screen 10 Synchronization method selection SYNC This unit supports the following 2 types of synchronization methods and one of the following is selected 1 Multiplexed vertical drive signal VD2 2 Internal synchronization INT default Input of a multiplexed vertical drive signal VD2 automatically switches to the VD2 synchronization even if the camera is set to other than the VD2 synchronization method When the VD2 synchronization is not selected internal synchronization can be selected 11 Privacy zone setting PRIVACY ZONE When undesired portions in the camera shooting area on the screen exist those portions privacy zone can be set to be hidden Up to 8 portions can be specified for the privacy zone ON 1 Grays the zone ON 2 Mosaics the zone OFF default Displays the zone normally Follow the procedure below to set the privacy zone Note The privacy zone function is disabled at initializing the unit i e right after turning on the power ZONE NUMBER 1 8 PUSH SET POSITION UPPER LEFT RET
21. T PRIVACY ZONE STABILIZER OFF EL ZOOM ON UPSIDE DOWN OFF LDC I 0 RET TOP END Step 1 Move the cursor to EL ZOOM and select ON and press the SET button The EL ZOOM screen appears 21 Step 2 Move the cursor to PUSH SET of ZOOM and press the SET button The zoom setting screen appears Step 3 Adjust the angular field of view by changing the electronic zoom factor up to 2x using the UP or DOWN button and press the SET button Note When the zoom factor is incremented resolution will be deteriorated Step 4 Move the cursor to PUSH SET of PAN TILT and press the SET button The pan tilt setting screen appears Step 5 Press the UP DOWN RIGHT and LEFT buttons to determine the position of the area to be set and press the SET button The position can be changed in the range of zoom factor set in the zoom setting screen 14 Upside down setting UPSIDE DOWN ON The video image can be reversed upside down OFF default The video image cannot be reversed upside down 15 Lens distortion correction LDC The image may be distorted depending on the lens used and the zoom factor By adjusting the lens distortion correction setting the distorted image can be converted to match the square monitor and achieve effects desired by the user Note Depending on the lens used complete correction may not be achieved 16
22. ack light compensation function 12 3 Electronic shutter setting SHUTTER 13 4 Gain control setting AGC 13 5 Electronic sensitivity enhancement setting SENS UP 13 6 White balance setting WHITE BAL 13 Manual fine adjustment of white balance 14 7 Digital noise reduction function setting DNR 15 8 Black and white mode setting D amp N IR CP310 CP310 CP300 D amp N ELE CP310 CP310 CP300 CF354 CF344 15 9 VMD setting VMD 16 Setting of motion detection 17 Setting of scene change detection 18 Camera system setting SYSTEM SETUP 19 10 Synchronization method selection SYNC 19 11 Privacy zone setting PRIVACY ZONE 19 12 Image stabilizer setting STABILIZER 20 13 Electronic zoom setting EL ZOOM 20 14 Upside down setting UPSIDE DOWN 21 15 Lens distortion correction LDC 21 16 Focus setting FOCUS CF354 21 Special menu setting SPECIAL SETUP
23. balance The white balance is manually fine adjusted after white balance automatically adjustment in the automatic color temperature tracking mode ATW1 ATW2 or automatic white balance control mode AWC Follow the procedures below CAMERA SETUP screen CAMERA SETUP SCENE1 ALC ELC ALC SHUTTER OFF AGC ON HIGH SENS UP OFF WHITE BAL AWC PUSH SET DNR HIGH AUTO1 VMD OFF RET TOP END D amp N IR ATW1 1 R B AREA RET TOP END ATW1 AREA 1 POSITION PUSH SET RET TOP END RESET I 0 I 0 CAMERA SETUP SCENE1 ALC ELC ALC SHUTTER OFF AGC ON HIGH SENS UP OFF WHITE BAL ATW1 DNR HIGH AUTO1 VMD OFF RET TOP END D amp N IR CAMERA SETUP screen Fine adjustment screen Area setting screen 15 Step 1 Set WHITE BAL to ATW1 ATW2 or AWC and press the SET button The fine adjustment screen appears Step 2 Move the cursor to R and B and press the LEFT or RIGHT button to fine adjust the level for each R stands for red and B stands for blue When the level indicator moves in the direction the color becomes deeper and when the level indicator moves in the direction the color becomes lighter Step 3 Move the cursor to AREA and press the SET button to enter AREA setting screen The area to detect white area of white balance can be set on the area setting screen The
24. e mode from the following CP310 CP310 CP300 AUTO1 default Automatically switches between color and black and white images in accordance with the illuminance The black and white mode is selected for dark images and the color mode is selected for bright images 16 AUTO2 Used a near infrared light source at night time ON Displays black and white images OFF Displays color images CP310 CP310 CP300 AUTO Similar to the basic functions of AUTO1 but does not change the IR filter CF354 Switches to black and white images when the illuminance around the camera is lower than approx 0 1 lx CF344 OFF default Displays color images Note CP310 CP310 CP300 When AUTO1 or AUTO2 is selected it is recommended to set AgC to ON CP310 CP310 CP300 If a subject is always moving or the screen is occupied with a uniform color brightness determination may not be per formed successfully because the brightness is merely determined by information from the CCD image sensor When AUTO2 is selected the wave length of the light source shall be 800 nm or longer WV CP300 WV CP304 WV CF354 and WV CF344 cannot set the switching brightness illuminance level of color images and black and white images To obtain color images a sufficient level of illuminance approx 30 lx or more is required Step 2 Press the SET button The D amp N IR screen app
25. e ranges from approx 2000 K to 6000 K 14 AWC Activates the automatic white balance control mode This adjustment is suitable for a location where a light source is stable The adjustment of the color temperature ranges from 2000 K to 10000 K When AWC is selected the white balance needs to be adjusted Note If the situation meets one of the followings color may not be accurately reproduced The subject is mostly highly colored The photographic scene is under the bright blue sky or at nightfall The illumination of the light illuminating the subject is insufficient When AWC is selected follow the steps below to adjust the white balance Step 1 Set WHITE BAL to AWC and press the LEFT button to change to AWC PUSH SET Step 2 Press the SET button and adjust the white balance AWC PUSH SET is reversely highlighted during adjustment When the reversely highlighted display is restored the white balance adjustment is completed Step 3 Press the RIGHT button to select AWC Refer to this page for fine adjustment of the white balance Note The adjustment of the color temperature ranges from approx 2000 K to 10000 K If the range is out of this adjustment range or lighting directed to a subject is too dark the white balance may not be adjusted In such a case AWC PUSH SET stays reversely highlighted Manual fine adjustment of white
26. ears Step 3 Move the cursor to LEVEL and select a brightness level at which switching between color and black and white images is performed from the following LOW Switches from color to black and white images when the ambient illuminance of the camera is less than 0 1 lx HIGH default Switches from color to black and white images when the ambient illuminance of the camera is less than 0 2 lx Note The switching illuminance level varies with subjects light sources and lenses The switching illuminance level varies in accordance with AGC setting page 13 The switching illuminances described above are reference values The switching illuminance shall be decided based on the actual installation environment There may be repeated switching between color and black and white images depending on the setting and environment Step 4 Move the cursor to DURATION TIME and select a time for switching between color and black and white images from the following 2 seconds 10 seconds default 30 seconds 60 seconds S L Step 5 Move the cursor to BURST BW and decide whether or not to provide a burst signal output in the black and white mode ON default Provides a burst signal output OFF Does not provide any burst signal output Note Images may not be displayed appropriately without burst signals when camera images are displayed in the black and white mode depending on a mo
27. enhancement WHITE BAL Specifies white balance adjustment DNR Selects the level of the digital noise reduction function D amp N IR ELE Performs each setting regarding the black and white mode such as switching between color and black and white images VMD Performs settings regarding VMD Video Motion Detection SYSTEM Performs the settings regarding the camera system such as synchronization and privacy zone SYNC Specities the synchronization type PRIVACY ZONE Hides undesired portions in the camera shooting area STABILIZER Decides whether or not to enable the image stabilizer EL ZOOM Switches the electronic zoom on and off UPSIDE DOWN Flips the camera images vertically or horizontally LDC Adjusts the lens distortion correction to convert the image so that it matches the square monitor FOCUS CF354 Selects the adjustment method and fine adjustment method for focus SPECIAL CHROMA GAIN Adjusts the chroma level color density AP GAIN Adjusts the aperture level PEDESTAL Adjusts the pedestal brightness level HUE Adjust the chroma phase hue PIX OFF Corrects image defects such as flaws COMMUNICATION CP310 CP310 CP300 CP310 CP310 CP300 Performs the communication setting of the system with a receiver into which this unit is integrated CAMERA RESET Restores the settings in the setup menu to the default settings SER NO Displays the serial number of this unit LAN
28. hile the camera is operated the setup mode is always DISABLE to prevent operation errors To perform settings in the setup menu change the setup mode to ENABLE The cursor is a reversely highlighted part Step 4 Perform the settings for each item Selection of setting item Press the UP or DOWN button to move the cursor Change of settings Press the RIGHT or LEFT button Display of advanced setup screen Press the SET button when is attached to the target setting item Return to previous setup screen Move the cursor to RET and press the SET button Return to the top screen Move the cursor to TOP and press the SET button to display the top screen of the setup menu Step 5 Move the cursor to END and press the SET button to return to the camera image screen or wait about 5 minutes and the setup menu will automatically close CAMERA SETUP SCENE1 ALC ELC ALC SHUTTER OFF AGC ON HIGH SENS UP OFF WHITE BAL ATW1 DNR HIGH AUTO1 VMD RET TOP END D amp N IR OFF 6 Screen transition diagram CP310 CP310 CP300 Top screen CAMERA ID screen CAMERA SETUP screen SYSTEM SETUP screen SPECIAL SETUP screen LANGUAGE SETUP screen MODEL WV CP310 SERIES CAMERA ID OFF CAMERA SYSTEM SPECIAL LANGUAGE END SETUP DISABLE LANGUAGE SETUP LANGUAGE ENGLISH SET RET TOP END CAMER
29. igital signal technology is applied to automatically detect the dark areas in the image acquire the brightness data around the dark areas and perform real time color adjustment by calculating the best correction curve for each area This function can be used to perform real time adjustment and correction of back light and dark area and reproduce natural clear images ON Uses ABS OFF default Does not use ABS Note When BLC is set to ON ABS displays and may not be operated Step 4 When BLC is set to OFF bright areas of an image are masked to facilitate the visibility of dark areas Move the cursor to MASK SET and press the SET button The mask setting screen appears Step 5 Press the UP dOWN righT and LEFT buttons to move the flashing cursor to the area to be masked and press the SET button When the selected area is masked the masked area will start blinking between stripes and white When the flashing cursor is moved to other areas the masked area will be displayed in white Repeat the above procedure to mask other areas as necessary Note To cancel the masking select the masked area to be canceled and then press the SET button The masked area will be deleted ALC CONT screen Mask setting screen CAMERA SETUP screen ALC CONT 1 BACK LIGHT COMP OFF ABS MASK SET LEVEL I 0 RET TOP END BLC OFF
30. ion increases the light sensitivity of the CCD and accordingly the image becomes brighter The magnification is unchanged for selection of FIX and the magnification is automatically adjusted in accordance with the illuminance of a photographic subject for selection of AUTO The magnification of the electronic sensitivity is selectable from the following OFF default X2 AUTO X4 AUTO X6 AUTO X10 AUTO X16 AUTO X32 AUTO OFF X2 FIX X4 FIX X6 FIX X10 FIX X16 FIX X32 FIX X64 FIX X128 FIX X256 FIX X512 FIX Note When ALC ELC is set to ELC or ALC only the AUTO mode is enabled When SHUTTER is set to options other than OFF the electronic sensitivity enhancement setting cannot be performed and appears When the magnification of SENS UP is increased the screen becomes coarser more whitish or more flawed However this phenomenon is normal 6 White balance setting WHITE BAL The white balance adjustment is selectable from the following ATW1 default Activates the automatic color temperature tracking mode The camera continuously check the color temperature of the light source and automatically adjusts the white balance The adjustment of the color temperature ranges from approx 2700 K to 6000 K ATW2 Activates the sodium lamp automatic color temperature tracking mode The camera automatically achieves an optimal white balance under the sodium lamp The adjustment of the color temperatur
31. is not cleared To set whether to reset the camera select YES or NO by using the SET button To set with a controller refer to the instruc tion manual of the controller 24 Serial number viewing SER NO Displays the serial number of this product 25 Camera language selection LANGUAGE SETUP A language for the setup menu is selected from the following The language selection can be made on the LANGUAGE SETUP screen displayed from the top screen Refer to page 5 for how to call up the screen Move the cursor to LANGUAGE and press the RiGhT or LEfT button to select the target language then move the cursor to SET and press the SET button Select the target language from the following JAPANESE ENGLISH default FRAN AIS ESPA OL DEUTSCH ITALIANO P CCK Note When the language is changed the specified camera title is cleared LANGUAGE SETUP screen LANGUAGE SETUP LANGUAGE ENGLISH SET RET TOP END 26 Shortcut operation Use of a system controller with the Camera function button allows users to perform the shortcut settings with use of the numeric keypad and camera function button The available shortcut operations with this unit are shown as follows System controller operation Setting contents 9 0 Camera function Black and white control D amp N ON CP310 CP310 CP300 9 1 Camera function Black and wh
32. ite control D amp N OFF 9 2 Camera function Black and white control D amp N AUTO1 CP310 CP310 CP300 Black and white control D amp N AUTO CP310 CP310 CP300 CF354 CF344 9 3 Camera function Camera title CAMERA ID ON 9 4 Camera function Camera title CAMERA ID OFF 9 8 Camera function Electronic zoom ON 9 9 Camera function Electronic zoom OFF 1 6 8 Camera function Black and white control D amp N AUTO2 CP310 CP310 CP300 1 6 9 Camera function Iris of lens IRIS OPEN 1 7 0 Camera function Iris of lens IRIS CLOSE 1 7 1 Camera function Electronic shutter SHUTTER ON 1 7 2 Camera function Electronic shutter SHUTTER OFF 1 7 3 Camera function Electronic shutter speed 1 step faster 1 7 4 Camera function Electronic shutter speed 1 step slower 1 7 5 Camera function Gain adjustment AGC ON 1 7 6 Camera function Gain adjustment AGC OFF 1 7 7 Camera function Electronic sensitivity up SENS UP FIX ON 1 7 8 Camera function Electronic sensitivity up SENS UP FIX OFF 1 7 9 Camera function Electronic sensitivity 1 step up FIX 1 8 0 Camera function Electronic sensitivity 1 step down FIX 1 8 1 Camera function Electronic se
33. m monitor or a video monitor when the adjustment is performed 20 Chroma phase hue adjustment HUE Press the RIghT or LEfT button to adjust the hue of the camera image Be sure to view a vector chromaticity indicator or a video monitor when the adjustment is performed 21 Pixel compensation PIX OFF flaws of pixel in the displayed camera image are corrected Up to 16 points can be corrected follow the procedure below PIX OFF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 DEL 000 000 SPECIAL SETUP screen PIX OFF screen Pixel compensation positioning screen RET TOP END SPECIAL SETUP CHROMA GAIN I 160 AP GAIN I 32 PEDESTAL I 15 PIX OFF CAMERA RESET PUSH SET SER NO XXXXXXXX COMMUNICATION COAX RET TOP END HUE I 0 Step 1 Move the cursor to PIX OFF and press the SET button The PIX OFF screen appears SPECIAL SETUP screen SPECIAL SETUP CHROMA GAIN I 160 AP GAIN I 32 PEDESTAL I 15 PIX OFF CAMERA RESET PUSH SET SER NO XXXXXXXX COMMUNICATION COAX RET TOP END HUE I 0 24 Step 2 Select a number 1 to 16 with which a pixel compensation point is registered and press the SET button The pixel compensation positioning screen appears Step 3 Press the UP DOWN RIGHT and LEFT buttons to move the crosshair cursor to the center of the flaw to be corrected and press the
34. nitor or VTR model to be used In such a case set the burst signal output to ON 9 VMD setting VMD The VMD function allows the camera to detect motion and scene change with the camera Detection of motion or scene change with the camera can be announced by issuing an alarm signal CP310 CP310 CP300 CP310 CP310 CP300 CP310 CP310 CP300 CP310 CP310 CP300 17 Important The following circumstances may result in detection failure or false detection Use the camera after adjusting the detection area and sensitivity Not enough difference in brightness between the background and the moving photographic subject or significant changes in brightness Dirt or water drops on the lens Insufficient brightness for example when shooting at night The subject is moving straight at the camera The subject is moving too fast or too slow The subject is too small or too large There are too many moving objects Light reflected through a window or from a road surface The camera is shaking Entry of outside light such as sunlight or the headlights of a car Flickering fluorescent light Subject change detection may fail in the following cases The lens is partially covered or covered with a transparent item The photographic subjects before and after changing the camera direction are similar False detection may occur for approx 1 minute after turning on
35. nsitivity up SENS UP AUTO ON 1 8 2 Camera function Electronic sensitivity up SENS UP AUTO OFF 1 8 3 Camera function Electronic sensitivity 1 step up AUTO 1 8 4 Camera function Electronic sensitivity 1 step down AUTO 1 9 0 Camera function Time for switching at D amp N AUTO 2 seconds 1 9 1 Camera function Time for switching at D amp N AUTO 10 seconds 1 9 2 Camera function Time for switching at D amp N AUTO 30 seconds 1 9 3 Camera function Time for switching at D amp N AUTO 60 seconds 2 0 1 Camera function Image stabilizer STABILIZER ON 2 0 2 Camera function Image stabilizer STABILIZER OFF 2 1 3 Camera function Scene file 1 2 1 4 Camera function Scene file 2 2 1 5 Camera function Gain AGC 1 step up 2 1 6 Camera function Gain AGC 1 step down CP310 CP310 CP300 Panasonic System Communications Company of North America Unit of Panasonic Corporation of North America www panasonic com business For customer support call 1 800 528 6747 Three Panasonic Way Secaucus New Jersey 07094 U S A Panasonic Canada Inc 5770 Ambler Drive Mississauga Ontario L4W 2T3 Canada 905 624 5010 www panasonic ca Panasonic System Networks Co Ltd 2012 sC0512 0 PGQP1295ZA Printed in China

Panasonic WV-CF344 Operating Instructions

Contents

Download Pdf Manuals

Related Search

Related Contents