Onkyo RC-391M User's Manual
Contents
1. 15cm 2 6 inches apart and the light emit ting parts facing each other 2 While pressing and holding down the desired MODE button on the RC 391M AUDIO CD DVD MD SAT CABLE VCR or TV press the ENT button then release the but tons When you press and hold down one of the MODE button the SEND LEARN indicator lights up When you press the ENT button the indicator turns off When you release the buttons the SEND LEARN indicator lights up again 3 Press and release the desired operation button on the RC 391M You may select any button within the rectangle shown in the gure When you press the button the SEND LEARN indicator turns off When you release the button the indicator lights up again 4 Press and hold down the desired button on the remote con troller of the other device until the SEND LEARN indicator on the RC 391M ashes twice The SEND LEARN indicator ashes twice slowly then lights up 5 Repeat Steps 3 4 to program other buttons in the same MODE Repeat Steps 2 4 to program other buttons in a different MODE 6 Press the MODE button to complete programming 7 Operate the programmed button to make sure the learning function works Note The remote controller codes for the Onkyo CD player tape deck DVD player and MD recorder have already been pro grammed into the buttons on the RC 391M You may program other remote controller codes into these buttons If you wish to restore the Onkyo preset codes aft2. Listening mode STEREO DSP DSP SURROUND Changing Listening mode SP A SP B Switching between Speakers A and B CH SEL Selecting a speaker DIMMER Adjusting the brightness of the display LEVEL Adjusting the speaker levels TEST Test tone MUTING Muting Turning the power on and off to the TX DS575 Controlling the TX DS575 MODE AUDIO CH SP A B DISPLAY POWER STNBY VOL MUTING Litening mode LEVEL DIMMER CH SEL INPUT SELECTOR TEST POWER ON SLEEP MODE AUDIO POWER STNBY POWER ON SEND indicator 32 Using the remote controller Note First connect an Onkyo CD player using the connection 1 Press the MODE CD button 2 Press the desired CD operation button TRACK Selecting a track DISC Selecting a disk in the CD changer Down Up Playback Stop Rewind Fast forward Pause EJECT Eject 0 1 9 10 Numeric keys You may also use the following buttons VOL q u Adjusting the volume level of the TX DS575 MUTING Muting the sound from the TX DS575 Note Make sure that you point the transmission part on the remote con troller toward the sensor area on the DVD player 1 Press the MODE DVD button 2 Press the desired DVD operation button POWER ON STNBY Turning
3. When you release the buttons the indicator lights up again 2 Press and release the button from which you wish to erase the learned code When you press the button the SEND LEARN indicator turns off When you release the button the indicator lights up again 3 Press and release the same button again The SEND LEARN indicator ashes twice slowly The learned code is erased Note If you do not press the button in step 2 or 3 for more than 30 sec onds the SEND LEARN indicator ashes three times quickly then the RC 391M exits Learning mode Resume Step 1 1 Press and hold down the MODE button from which you wish to erase the learned code and press the ENT button twice Then release the buttons When you press the MODE button the SEND LEARN indica tor lights up When you press the ENT button the indicator turns off When you release the buttons the indicator ashes twice slowly then lights up again 2 Press and release the same MODE button again When you release the button the SEND LEARN indicator ashes twice slowly The learned code is erased Note If you do not press any button for more than 30 seconds the SEND LEARN indicator ashes three times quickly then the RC 391M exits Learning mode Resume Step 1 If you make a mistake during programming the SEND LEARN indicator ashes three times quickly the RC 391M exits Learn ing mode Resume Step 1 If have programmed many button operations to a s
4. 31 Using the remote controller Overview When you use a remote controller typically you press one of the MODE buttons that corresponds to the device you wish to control then press the operation buttons For example if you wish to control the TX DS575 from a remote controller rst press the MODE AUDIO but ton then press an appropriate operation button To control a CD player press the MODE CD button then press an appropriate operation but ton First press the desired MODE button to make sure that the TX DS575 is set to a correct mode Using the RC 391M to control each device Note Before operating the RC 391M turn on the POWER switch on the TX DS575 so that the unit enters standby mode 1 Press the MODE AUDIO button 2 Pressing the POWER ON buttons will switch between power on Pressing the POWER STNBY button will power standby SEND indicator This indicator acts as a guide when commands are programmed into or sent by the remote controller It also warns the user when an error is made or battery power is low 1 Press the MODE AUDIO button 2 Press the desired operation button Shaded buttons in the gure are the operation buttons used to control the TX DS575 SLEEP Sleep function POWER ON STNBY Power on standby DISPLAY Changing the display VOL q u Adjusting the volume CH Tuner preset number increment decrement INPUT SELECTOR
5. battery cover and remove the batteries 2 While pressing and holding down the POWER ON button and the POWER STNBY button insert the batteries in the correct direction After inserting the batteries release the buttons The SEND LEARN indicator ashes slowly 3 Press the ENT button The SEND LEARN indicator lights up for about ten seconds then turns off All programmed codes are erased and the button memories return to the factory presets Note Proceed to Step 3 immediately after Step 2 Otherwise the bat teries will be consumed quickly If you press any button other than the ENT button in Step 3 no codes will be erased In this case repeat the steps from the beginning Erasing all codes and operations programmed in the buttons 2 3
6. form the learn operations for each function individually to store each function to a button on the RC 391M For instructions regarding the operation of learned units please refer to the instruction manual for each product Even after codes have been memorized please keep your old remote controller in a safe place If the memorized codes are lost when the batteries run down it will be necessary to memo rize them once again using the old remote controller Make sure both the RC 391M and the product s own remote controller have fresh batteries If either of them has batteries that are wearing down it may be impossible to store the remote controller codes into the RC 391M or the product may not respond properly to the buttons on the RC 391M for which the remote controller codes were stored into memory Programming procedure 1 3 2 6 4 Light 5 to 15 cm 2 to 6 inches The button you wish to memorize RC 391M 35 Programming the remote controller codes of other devices into the RC 391M See page 39 for information on how to erase the learned codes from all buttons You can erase a learned code You cannot erase preset codes Erasing a code programmed in a button 1 Press and hold down the corresponding MODE button and press the ENT button then release the buttons When you press the MODE button the SEND LEARN indica tor lights up When you press the ENT button the indicator turns off
7. the power on and off to the DVD player DVD SET DVD setup DVD player on screen button MENU Displaying the menu ququ Moving the cursor ENTER Con rming the selection RETURN Return DVD player buttons Down Up Playback Stop Rewind Fast forward Pause EJECT Eject 0 1 9 10 Numeric keys ENT Con rm You may also use the following buttons VOL q u Adjusting the volume level of the TX DS575 MUTING Muting the sound from the TX DS575 Note The ENT button on the right below the numeric keys has the same function as ENTER of the ENTER cursor button Controlling an Onkyo CD player Controlling an Onkyo DVD player MODE CD CD operation buttons Numeric keys MODE DVD DVD operation buttons Numeric keys ENT button 33 Using the remote controller Note Make sure that you point the transmission part on the remote con troller toward the sensor area on the MD recorder 1 Press the MODE MD AUX button 2 Press the desired MD operation button Turning the power on and off to the MD recorder POWER ON STNBY Turning on or standby the power to the MD recorder Down Up Playback Stop Rewind Fast forward Record Pause EJECT Eject 1 9 10 Numeric keys ENT Con rm You may also use the following buttons VOL q u Adjusting the volume level of the TX DS575 MUTING Muting the sound from the TX DS575 Note First connect an Onkyo ta
8. DE button then release the buttons When you press the MODE button the SEND LEARN indica tor lights up When you press the MACRO MODE button the indicator turns off When you release the buttons the indicator ashes once 2 Press the MACRO MODE button again The SEND LEARN indicator ashes twice slowly The learned operation is erased 1 Press and hold down any one of the MODE buttons and press the MACRO DIRECT button Then release the but tons When you press the MODE button the SEND LEARN indica tor lights up When you press the MACRO DIRECT button the indicator turns off When you release the buttons the indicator ashes once 2 Press the MACRO DIRECT button again The SEND LEARN indicator ashes twice slowly The learned operation is erased Note If you do not press any button for more than 30 seconds the SEND LEARN indicator ashes three times quickly then the RC 391M exits Learning mode Resume Step 1 If you press a wrong button in Step 2 you may have overwritten the memory of the button you pressed Erasing a learned remote controller button oper ation from the MACRO MODE buttons Erasing a learned remote controller button oper ation from the MACRO DIRECT button 1 1 2 1 2 1 39 Using a Macro function This procedure will erase all remote controller codes for the other devices and all macro operations that have been programmed in the RC 391M see pages 34 36 and 37 1 Open the
9. Press the operation buttons in series you wish to program into the MACRO MODE button Press the MODE AUDIO POWER ON CD INPUT SELEC TOR MODE CD buttons and a numeric key When you press the button the SEND LEARN indicator turns off When you release the button the indicator lights up 3 Press the MACRO MODE button to complete program ming The SEND LEARN indicator ashes twice slowly Repeat Steps 1 3 to program other series of button operations into another MODE button 4 Check to see if the series of button operation has been cor rectly learned Point the remote controller toward the TX DS575 press the MODE CD button and press the MACRO MODE button to see if the unit responds as programmed Transmitting the codes in Macro mode takes a while During transmission point the remote controller toward the device to be controlled Note You may program up to 16 button operations into each MACRO button If you try to program the 17th step it will be ignored If you do not press any button for more than 30 seconds during the procedure the SEND LEARN indicator ashes three times quickly then the RC 391M exits Learning mode Resume Step 1 If you make a mistake during programming the SEND LEARN indicator ashes three times quickly then the RC 391M exits Learning mode Resume Step 1 If you erase one of the operation buttons already programmed in the MACRO MODE button or if you program a different code into s
10. er you program new codes erase the new codes See page 35 Note The remote controller has 408 memory slots 51 buttons 8 modes although this number varies signi cantly depending on the manufacturers and types of the remote controller you wish to program into the RC 391M It is recommended that you deter mine which button functions have priority for programming If you do not press any button for more than 30 seconds during the procedure the SEND LEARN indicator ashes three times quickly then the RC 391M exits Learning mode Resume Step 2 If you make a mistake during programming the SEND LEARN indicator ashes three times quickly then the RC 391M exits Learning mode If you try to program beyond the learning capacity of the RC 391M the SEND LEARN indicator ashes six times quickly then the RC 391M exits Learning function Try programming in a button of other MODE Follow the same procedure when you wish to program new codes into the already programmed buttons This remote controller uses infrared rays Most remote control ler codes can be memorized using the infrared system however depending on the degree to which the system differs there may be some rare occasions when memorization is not possible Some remote controllers use a single button to perform different functions with the function code changing each time the button is pressed If you are using this kind of controller please per
11. ingle MODE button the SEND LEARN indicator may remain illuminated continuously in Step 2 This is not malfunction Erasing a learned code Erasing a learned code from a MODE button SEND LEARN indicator MODE buttons ENT SEND LEARN indicator MODE buttons ENT 36 Using a Macro function A Macro function enables you to program a series of button operations on the remote controller into a single button For example you need to follow the steps below to play a CD player connected to the TX DS575 without using the Macro function 1 Press the MODE AUDIO button 2 Press the POWER ON button 3 Press the CD INPUT SELECTOR button 4 Press the MODE CD button 5 Use the numeric keys to select the desired song This operation will be two button presses away if you program these steps into a macro button What is a Macro function You may program the desired steps into each of eight MODE but tons The following example explains how to program Steps 1 5 described above into the MACRO MODE button under the MODE CD button CD mode 1 Press and hold down the desired MODE button you wish to program in this case MODE CD button and press the MACRO MODE button Then release the buttons When you press the MODE CD button the SEND LEARN indicator lights up When you press the MACRO MODE button the indicator turns off When you release the buttons the indicator ashes brie y then lights up again 2
12. ke sure that the device responds as programmed Transmitting the codes in Macro mode takes a while During transmission point the remote controller toward the device to be controlled Note You may program up to 16 button operations into the MACRO DIRECT button If you try to program the 17th step it will be ignored If you do not press any button for more than 30 seconds during the procedure the SEND LEARN indicator ashes three times quickly then the RC 391M exits Learning mode Resume Step 1 If you make a mistake during programming the SEND LEARN indicator ashes three times quickly then the RC 391M exits Learning mode Resume Step 1 If you erase one of the operation buttons already programmed in the MACRO MODE button or if you program a different code into such a button the operation button will no longer work In this case program the buttons again to avoid malfunction Macro Direct Learning function 1 3 1 Tip The codes programmed into a MACRO button will be transmitted with an interval of 0 5 seconds However some devices may not be able to complete one opera tion in 0 5 seconds and may miss the next code In this case press one operation button press the correspond ing MODE button then press another operation button to extend the interval between the two operations up to one second 38 Using a Macro function 1 Press and hold down the corresponding MODE button and press the MACRO MO
13. pe deck using the connection See page 9 1 Press the MODE AUDIO TAPE button 2 Press the desired tape deck operation button Playback Stop Rewind Fast forward Recording pause Reverse playback You may also use the following buttons VOL q u Adjusting the volume level of the TX DS575 MUTING Muting the sound from the TX DS575 No preset codes are programmed into the MODE SAT CABLE VCR and TV buttons You can use these buttons to program remote controller signals of other devices See page 34 You may use the following buttons VOL q u Adjusting the volume level of the TX DS575 MUTING Muting the sound from the TX DS575 Controlling an Onkyo MD recorder Controlling an Onkyo tape deck MODE SAT CABLE VCR and TV buttons REC REC MODE MD MD operation buttons Numeric keys ENT button MODE AUDIO TAPE operation buttons MODE SAT CABLE VCR TV 34 Programming the remote controller codes of other devices into the RC 391M The RC 391M has two learning functions One is a normal learning function that enables the RC 391M to learn other remote controllers codes The other is a macro learning function which enables the RC 391M to learn a series of codes already memorized in the remote con troller into one MACRO button Program the codes for each mode AUDIO CD DVD MD SAT CABLE VCR and TV 1 Place the RC 391M and the remote controller for another device with 5
14. uch a button the operation button will no longer work In this case program the buttons again to avoid malfunction Programming Macro mode 1 3 2 1 2 2 2 2 Tip The codes programmed into a MACRO button will be transmitted with an interval of 0 5 seconds However some devices may not be able to complete one opera tion in 0 5 seconds and may miss the next code In this case press one operation button press the correspond ing MODE button then press another operation button to extend the interval between the two operations up to one second 37 Using a Macro function A series of remote controller button operations can be memorized into the MACRO DIRECT button for one touch control Note You can program only one series of button operations into the MACRO DIRECT button 1 Press and hold down any one of the eight MODE buttons and press the MACRO DIRECT button Then release the buttons When you press the MODE button the SEND LEARN indica tor lights up When you press the MACRO DIRECT button the indicator turns off When you release the buttons the indicator ashes brie y then lights up again 2 Follow Steps 2 in the Programming Macro Mode on page 36 3 Press the MACRO DIRECT button to complete the proce dure The SEND LEARN indicator ashes twice slowly 4 Check to see if the button has been programmed correctly Point the RC 391M toward the TX DS575 and press the MACRO DIRECT button and ma
Download Pdf Manuals
Related Search