Newcon Optik NVS-33 User's Manual
Contents
1. Light gain 35000 EM Date of production Quality Inspector s signature 38 Unit serial number The unit complies with all technical specifications and has passed the inspection Date of production Quality Inspector s signature Quality Assurance Seal 39 NEWCON OPTIK 2010 Printed in Canada 402. NEWCON OPTIK Operation Manual NIGHT VISION ATTACHMENT NVS 33 105 Sparks Ave Toronto ON M2H 2S5 Canada IMPORTANT INFORMATION Read prior to activation You have purchased a sophisticated electronic device To operate it properly please read this manual fully Ignoring operation procedures described in this manual will void your warranty NEVER Disassemble the unit Device contains a source of high voltage which may be hazardous to your health NEVER Aim active unit towards intense light sources i e lights headlamps campfires the Sun the Moon etc NEVER Reverse the polarity of a battery NEVER Connect the unit to external power source ALWAYS Remove battery when not in use for a long period of time ALWAYS Keep the objective lenses covered other then when in use during the night operation ALWAYS Store the unit in a warm dry place when not in use WARNING Use of this device may be restricted by the national regulations Please consult with local authorities TABLE OF CONTENTS Ils OVefVIew coa aet eee on repe BAS 4 1 2 Key features 8 33 5 2 DESIGN of NVS 33 anehon eni 6 3 SPECIFICATIONS 8 4 DELIVERY SET 10 5 INSTALLATION ON A 12 5 1 Installation with thread usage 12 5 2
3. wait for a few seconds and turn it on again If the image has been lost at the moment of a shot check contacts in the battery compartment 34 Condensation accumulates on the parts In order to avoid misting of the eyepiece lens at cold use the special protective cover Black dots on the screen These are some blemishes in the image intensifier which do not affect the performance or reliability of a night vision device Blemishes may vary in size and number they are inherent in the manufacturing process Most of them are seen in the daytime only and become almost invisible during the night time 9 WARRANTY NEWCON warrants this product against defects in materials and workmanship for one year from the date of the original purchase Longer warranty is available subject to the terms of the specific sales contract Should your Newcon product prove to be defective during this period please deliver the product securely packaged in its original container or an equivalent along with the proof of the original purchase date to your Newcon Dealer Newcon will repair or at its option replace with the same or comparable model the product or part thereof 35 which on inspection by Newcon is found to be defective in materials or workmanship What This Warranty Does Not Cover NEWCON is not responsible for warranty service should the product fail as a result of improper maintenance misuse abuse improper installa
4. Installation with a riflescope mounting adapter NC540 4 cae ette erepto ERE etes 4 5 3 Installation on a Picatinny rail 18 6 OPERATION INSTRUCTIONS 21 6 1 Battery installation sss 21 6 2 Testing NVS 33 in the daytime 23 6 3 Testing NVS 33 at night 24 6 4 Testing NVS 33 at night with daytime scope 24 6 5 Operation at 25 6 6 Use in a dark time as a 2x night vision monocular 29 6 7 Operation with remote 30 7 STORAGE AND MAINTENANCE 32 8 TROUBLESHOOTING ere 34 9 35 10 CUSTOMER SUPPORT 37 11 ACCEPTANCE CERTIFICATE 38 1 BRIEF DESCRIPTION 1 1 Overview NVS 33 is an afocal night vision attachment to a daytime weapon scope designed for precise aiming in darkness The device is equipped with a high quality generation 3 electro optical image intensifier tube that amplifies light in the visible and IR spectrum providing for up to a 400 700 m effective observation range at low light Observation range depends on the characteristics of the daytime scope NVS 33 is attached to and actual observation conditions such as available light atmosphere transparency and target
5. able 30 The NVS 33 night vision attachment has the capability of operation with the external remote control that turns on and off the device itself and its IR illuminator Operation procedure 1 Insert the jack of the remote control into the female connector 2 Fig 7 2 Fix the remote control 4 Fig 7 on the weapon by the fixating band 6 Fig 7 in the comfortable place on the butt 3 Press and release the button 3 Fig 7 to turn the device on 4 Press and release the button 5 Fig 7 to turn the IR illuminator Special order only on The power of the IR illuminator corresponds to the position of the switch 1 Fig 7 5 Next press and release of the buttons 3 Fig 7 and 5 Fig 7 will toggle the controlled functions 31 7 STORAGE AND MAINTENANCE WARNING If NVS 33 has been stored for a long time at temperature lower than 40 C 40 F then prior to using the device must be kept at an ambient temperature of 10 C 14 F to 40 C 104 F with humidity below 80 NVS 33 is a sophisticated precise optical instrument equipped with electronics It should be handled with due care e Unit contains fragile components and sensitive optics Avoid impacts dust moisture and sharp changes of temperature e Do not touch the optical surfaces other than for cleaning Doing so may damage the anti reflection coating e Clean optical surfaces with professional lens cleaning suppli
6. ap 1 pc Remote control switch 1 pc Operator s manual 1 pc Ocular protective cap 1 pc Soft case 1 pc CR123 Battery 1 pc Additional battery cap for AA battery 1 pc Cleaning cloth 1 pc Quick release Picatinny mount 1 pc Light suppressor 1 pc Riflescope mounting adapter 1 pc Optional accessories Hard case 1 pe Riflescope mounting adapter 1 pe of NC540 56 NC540 42 each Threaded adapters M48 M52 M54 1 pe of M55 each M540 converter to convert NVS33 1 pe of into 2x monocular each IR illuminator mounted on the 1 pe sight Configuration 2 Exact delivery set depends on particular order 5 INSTALLATION ON A RIFLE 5 1 Installation with thread usage Your NVS 33 matches to the inner thread M52x0 75 of the objective lens of those daytime riflescopes that can accept daytime filters If your scope does not match this thread use mechanical adapters that transform M52 into M54 M55 or M48 threads M52 adapter is used to increase the depth of the thread in case if the scope objective lens is close to the edge of the scope Mount your night vision attachment as follows If necessary screw the corresponding threaded adapter in the thread on the adapter ring 2 Fig 1 Loose the retention pin 4 by turning it counters clockwise Turn the adapter ring 2 counter clockwise and screw it into the inner thread of the daytime riflescope until s
7. ditions of higher illumination in moony night with external light sources of illumination or if the target is located in front of light background sand snow The identification range decreases in conditions of low illumination low atmospheric transparency or if the target is located in front of dark background plough land trees etc 26 7 If necessary turn on the IR illuminator 6 Fig 2 Special order only NVS 33 is protected against accidental illuminator switch by the design of the switch handle Press and rotate the switch 5 Fig 2 to activate the illuminator Divergence of IR beam could be changed from 5 to 20 degree by rotating of the IR lens The sight is not necessarily equipped with the IR illuminator Your sight configuration 1s determined by your order Working with IR illuminator can potentially disclose your location to the other side 8 The fire adjustment of the combination daytime riflescope night vision attachment should be performed in accordance with the instructions of the fire adjustment of the daytime riflescope 9 Turn off the switch 5 Fig 2 after work is over 10 Close the objective lens cover 27 When mounted in front of the daytime riflescope night vision attachment NVS 33 can change zeroing as not more than 3 cm at 100 m This is connected with changes in the weapon balance light distortions in the image intensifier tube technological limits of the adj
8. e scope Select necessary zoom of the daytime scope By turning the knob 7 Fig 1 of NVS 33 acquire the target through daytime scope 24 6 5 Operation at night Operation procedure 1 Check the adjustment of the daytime riflescope diopter adjustment parallax adjustment etc 2 Install the battery into the NVS 33 and mount it in front of the daytime riflescope as described above Being mounted in front of a daytime riflescope the night vision riflescope attachment NVS 33 keeps all tactical features of a daytime riflescope zoom level adjustment step etc intact 3 Open the objective lens cover 9 Fig 1 4 Turn the switch 5 Fig 1 of the device into ON position You should see a yellowish green light through the eyepiece of a daytime riflescope the device works in passive mode 5 Setthe required magnification of a day riflescope 25 In order to get the maximum quality of night picture through the daytime riflescope we recommend using riflescope magnifications from 3 to 12 6 Aim the rifle to an object and focus the objective of device with the knob 7 Fig 1 on its top until you get maximum sharpness of the observed picture Observation and identification range provided by the night vision riflescope attachment NVS 33 depends on the ambient illumination atmospheric transparency and contrast between the target and background Identification range increases in con
9. es e Use only soft clean cloth to clean the exterior of the device 32 Keep away from sources of heat such as heating appliances sunlight or central heating Do not keep the device at temperatures higher than 60 C 140 F Switch off the unit and remove the batteries during the extended periods of non operation Do not apply excessive force or pressure to the lens assembly this may damage fragile elements and thread connections Small dark and or white marks may be seen in the field of view This does not affect the operational capabilities of the device Do not remove the cover from the lens other than for night time operation 33 8 TROUBLESHOOTING The scope does not turn on Check whether the batteries are installed properly Check the charge of the batteries Replace 1f they are weak Do not mix old batteries with new ones The target does not appear in focus Bring the target to the center of the image By turning the knob 7 Fig 1 achieve the clearest target acquisition on the screen If NVS 33 is used with daytime scope re focus it Repeat the focusing of NVS 33 and scope if necessary If the image still does not seem to be in focus clean the lenses They could be foggy or dusty Image has disappeared If the objective lens of switched on NVS 33 are exposed to bright light it automatically shuts off to protect the image intensifier tube from overload When it happens turn the unit off
10. of the daytime riflescope For example to use NVS33 with Swarovski 761 2 12x50 scope you should take the adapter NC540 50 During shooting with the night vision riflescope attachment NVS 33 which is attached to the daytime riflescope with help of the adapter the adapter ring could move along the objective lens of the daytime riflescope The size of this movement depends on the tightening force of the adapter screw 5 recoil force of weapon etc and could be equal to 1 mm on each shot This movement is allowed and do not affect on the impact point However the position of the adapter should be controlled after each shot in the shooting process 5 3 Installation on a Picatinny rail The night vision attachment NVS 33 can be installed on a Picatinny rail in front of the daytime riflescope For this purpose it has an additional Picatinny rail on the side Night sight Picatinny rail Fig 4 The rail adapter is designed to make the night vision attachment profile as low as possible to work together with low profile scopes 18 Quick release Fig 5 Night sight rail rifle rail clamp clamp with screw Actual height of the adapter must be determined at the moment of ordering of the Picatinny rail adapter Each rifle and riflescope combination is unique and it is necessary to know height of the line of sight above the Picatinny mount to produce this part precisely Distance between NVS 33 line of sight and daytime
11. r 12 Objective lens 6 Device body 10 11 12 13 Fig 2 Configuration 2 Special order with IR Illuminator 1 Ocular 8 IR illuminator 2 Adapter ring with 9 Objective lens cover thread 3 Fixating ring 10 Battery compartment cap 4 Retention pin 11 Battery compartment 5 On Off and IR switch 12 Remote switch connector 6 Device body 13 Objective lens 7 Objective focus adjustment knob 3 SPECIFICATIONS Optical Magnification x Field of view degrees Daytime scope magnification x Acceptable Recommended Focus length mm 78 F number 1 5 Focus range 10 m to infinity Image intensifier tube N3XT3631IC Type Gen 3 18mm MCP Gain min 35 000 Resolution lp mm 57 Infrared illuminator optional Type IR diode Power mW 75 Illumination angle degree 5 20 Illumination wavelength nm 805 Electrical parameters Power supply 1 Bes or AA attery Voltage V 3 Continuous work time h min 60 Mechanical characteristics Dimensions mm 180 x 75 x 60 Weight g 615 Environmental conditions Operating temperature range 50 C to 55 C Relative humidity Up to 98 Waterproof rating IP67 NOTE As the design is being continuously improved some parameters may differ from those given above 4 DELIVERY SET NC540 50 NVS 33 1 pc Objective lens c
12. reflectivity The observation range increases by brighter light at moony night or if the object is positioned against a light background such as snow or grass The range decreases at lower light low atmosphere transparency or if the object is positioned against dark background such as plough land desert stems of trees etc 1 2 features of NVS 33 e Installation of NVS 33 in front of a day scope on a weapon does not affect the latter s zeroing and scope s tactical parameters e Exit pupil fits a broad range of daytime scopes e Accurate internal focus adjustment mechanism e High quality image within the entire field of view e Withstands large calibre recoil e Optionally supplied with MIL STD 1913 Weaver Picatinny mount e Mounting adapters fit a vast majority of the daytime riflescopes e Upto 1 meter of immersion waterproof design e be equipped with an optional powerful IR Illuminator e Low battery indicator e Two possible types of batteries AA and CR123 can be used e Low power consumption e Compact and lightweight 2 DESIGN of NVS 33 1 Fig 1 Configuration 1 1 Ocular with light suppressor 7 Objective focus adjustment knob 2 Adapter ring with thread 8 Objective lens cover 3 Fixating ring 9 Battery compartment cover 4 Retention pin 10 Battery compartment 5 On Off switch 11 Remote switch connecto
13. riflescope line of sight must not exceed 2 mm In case of two different rails are used the angle deviation between two rails must not exceed 2 degrees Picatinny rail adapter is attached to the scope permanently by means of a small clamp and screw The other side of the adapter is equipped with quick release clamp which can be adjusted for width and pressing exertion It allows almost immediate installation and de installation of the sight on the rifle Light suppressor is used to prevent the user disclosure by greenish light emitted by the working NVS 33 It is attached on to the night sight instead of mounting adapters The size of the light suppressor is determined by the riflescope design The night sight should be mounted on the Picatinny rail as close to the riflescope as possible 20 6 OPERATION INSTRUCTIONS WARNING Lens cover should be always on when switching on NVS 33 in bright light conditions Never aim the lens in the directions of bright light 6 1 Battery installation NVS 33 is powered by one standard CR123A battery or 1 AA battery The type of the used battery is determined by the battery compartment cap By default the sight is delivered with CR123 battery compartment cap screwed to the battery compartment AA battery compartment cap is included into delivery set Prior to battery installation make sure it is in good condition 21 Battery compartment cover Fig 6 To install bat
14. s of the set quantity x daytime riflescope thickness NC540 56 56 mm Ipc xImm 2pc x2mm NC540 50 50mm Ipc xImm 1 2 mm NC540 42 42 mm Ipc xImm 1 2 mm Fig 3 NVS 33 night vision attachment Adapter ring Fixing ring with the pin NC540 50 NC540 56 NC540 42 adapter Adapter screw Plastic inserts 1 2 3 4 5 6 Ts Objective lens of a daytime riflescope 15 Assemble the adapter and mount the night sight attachment as follows Fig 3 1 It s necessary to select needed quantity of the plastic inserts 6 for a particular external diameter of the objective lens of the daytime riflescope The objective lens of the daytime riflescope 7 should fit loose but without apparent drift into the adapter 4 with the installed inserts 6 and loosen adapter screw 5 2 After the inserts 6 are installed the adapter 4 must be screwed on the adapter ring 2 against the stop and locked by the retention pin 3 in the counter clockwise direction 3 Put the night vision attachment with the fixed adapter 4 on the objective lens of the daytime riflescope 7 and fix it by the adapter screw 5 The lens of the daytime scope must be positioned at least 15 mm behind the front edge of the scope body This excludes mechanical contact of the NVS 33 night sight attachment and daytime scope objective lens Last digits in the NC540 adapters part numbers correlate with the diameter
15. teries unscrew the battery compartment cover insert batteries observing correct polarity and screw the cover back on Your NVS 33 is equipped with the low battery indicator located in the field of view This indicator starts blinking in red colour when the battery charge is low Change the battery as soon as possible 22 6 2 Testing NVS 33 in the daytime Daytime mode of NVS 33 was designed for testing purposes only Image may be fuzzy To test the device in the daylight 1 Turn switch 5 Fig 1 into ON position 2 Direct the device at an object within 10 20 m from the viewer 3 Turning the focus knob 7 Fig 1 adjust focus to obtain 4 The sharpest image visible through the eyepiece Keep the objective lens cover closed during daytime Do not direct night vision attachment to bright sources of light the Sun highly reflective surfaces and similar objects This may damage the image intensifier tube inside 23 6 3 Testing NVS 33 at night To test NVS 33 in darkness 6 4 l 2 3 Take off the lens cover 9 Fig 1 Turn on the device using switch 5 Fig 1 By turning knob 7 Fig 1 obtain clear image of the object Testing NVS 33 at night with daytime scope Install NVS 33 see Chapter 5 INSTALLATION ON A RIFLE Take off the lens cap 9 Fig 1 Turn on the device using on off switch 5 Fig 1 Greenish image must be seen through the daytim
16. tion neglect damage caused by disasters such as fire flooding lightning improper power supply or service other than by a NEWCON Authorized Service Postage insurance and shipping costs incurred while presenting your NEWCON product for warranty service are your responsibility If shipping from North America please include a cheque or money order payable to NEWCON OPTIK for the amount of 25 00 to cover handling and return shipping 36 10 CUSTOMER SUPPORT Should you experience any difficulties with your Newcon Optik product please consult this manual first If the problem remains contact our customer support department at 1 416 663 6963 or toll free at 1 877 368 6666 North America only Our operating hours are 9am 5pm Monday Friday Eastern Standard Time Under no circumstances should the equipment be sent to Newcon without authorisation from our technical support department Newcon accepts no responsibility for unauthorized returns To locate NEWCON Authorized Dealer call 1 416 663 6963 or fax 1 416 663 9065 Email newconsales newcon optik com Web www newcon optik com The defective products should be shipped to US Customers 2331 Superior Ave Cleveland OH 44114 USA From all other countries 105 Sparks Ave Toronto ON M2H 285 CANADA 37 11 ACCEPTANCE CERTIFICATE Image Intensifier Tube serial number Minimum Measured Photocathode sensitivity 500 integral
17. top Avoid applying extra strength while tightening 1 Turn the night vision attachment NVS 33 so that the objective focus adjustment knob 7 is located on top 2 Lock the attachment in this position by turning the fixating ring 3 in the counter clockwise direction 12 The night vision attachment NVS 33 is ready for use NVS 33 can be screwed directly into the Newcon 3 12x50 riflescope Its design allows such mounting without any additional adapters To attach NVS 33 in front of NC 3 12x50 proceed as described above without using threaded adapters Due to different designs of the daytime riflescopes we cannot guarantee that threaded connection is supported in all cases This design may be not strong enough to hold the night vision attachment during shooting In such case the ring and objective thread of the daytime scope may be damaged The manufacturer is not responsible for use of NVS 33 night sight attachment by a threaded connection on the scope models other than those which were approved by Newcon Optik There is no need to re zero daytime scope or perform any additional adjustment when NVS 33 is installed on the rifle 5 2 Installation with a riflescope mounting adapter NC540 Three adapter modifications are available for the NVS 33 night vision attachment to install it in front of daytime riflescopes of different models Adapter Diameter of the Plastic inserts objective len
18. ustment of the night riflescope attachment This imprecision usually appears as fixed value and can be easily compensated by the adjustment mechanism of the daytime riflescope We recommend you to make 10 15 shots with the mounted NVS 33 before practical using it in field conditions Such test will check NVS 33 by a real shooting impact and thus will increase reliability of the whole system DO NOT FORGET TO TURN OFF THE NIGHT VISION RIFLESCOPE ATACHMENT AFTER USE 28 6 6 Use in a dark time as a 2x night vision monocular Operation procedure Screw the optional M 540 optical monocular into the eyepiece of the NVS 33 night vision attachment Open the objective lens cover 9 Fig 1 Turn the switch 5 Fig 1 of the device into ON position You should see a yellowish green light through the eyepiece of a daytime riflescope the device works in passive mode Choose the object of observation If necessary turn on the IR illuminator 5 Fig 2 Special order only as described above the device works in active mode Turn off the switch 5 Fig 1 after work is over Close the objective lens cover 29 6 7 Operation with remote control 1 On Off switch 2 Female connector for the remote control 3 The start button of the remote control 4 Remote control body 5 The start button of the IR illuminator Special order only 6 Fixating band 7 Remote control c
Download Pdf Manuals
Related Search