Netgear FA510 Installation Guide
Contents
1. NETGEAR FA Gato lt a Installation Guide VU Start Instructions in this guide are for users of Windows who are installing the Model FA510 Network Card For instructions on installing and verifying the Windows network driver refer to Install the Windows Network Driver on the other side of this guide These four easy steps provide information for installing your Model FA510 Network Card 1 Verify Package Contents 2 Install the Network Card 3 Connect the Network Cables 4 Install the Network Driver As a last step be sure to fill out and send in your warranty card To register online direct your Web browser to the Web page at http www netgear com T Verify Package Contents Unpack the contents of the package and make sure that you have everything Model FA510 Network Card e RJ 45 adapter cable i e Category 5 10 100 Mbps ii UTP cable provided with Model FA510C Network Card Drivers and ____ CSCSCSCSC lt Diagnostics Disk 9 Installation guide Warranty amp Owner Registration Card and Support Information Card 9034FA Verify PC Requirements The instructions given in this guide are for using the NETGEAR Model FA510 Network Card in a PC that has a Microsoft Windows operating system Model FA510 Network Card Installation Guide Install the Network Card The Model FA510 Network Card is hot swa2. Install the Network Driver This guide provides you with instructions for installing the Windows Network Driver The steps given in these instructions are for users of Windows 98 If you are using Windows 95 read these instructions thoroughly for an overview of the steps that are necessary for the installation of the software driver If you are installing network cards and drivers on more than one computer operating with Windows 95 you might find that all versions of Windows 95 do not respond with the same screens and windows might open in a different order Note You must install the network card instructions on other side of this guide before installing the network driver Before you proceed with the installation steps decide on a name for your network and for each PC each name must be only one word You also need to have the Windows CD ROM and the FA510 Drivers and Diagnostics Disk ready to use in the installation process Note If the Insert Disk window opens and the Please insert the disk labeled Windows 98 message appears at any time during the following process insert the Windows 98 CD ROM in Drive D the CD ROM drive and click on OK Then follow the next step in the instructions 1 Turn on the power to the computer and start Windows 98 The new hardware is found Add New Hardware Wizard This wizard searches for new drivers for PCI Ethernet Controller A device driver is a software prog
3. ME Computer Disk drives re f Display adapters aS Floppy disk controllers Fy Hard disk controllers 10 Infrared devices E Keyboard E Monitors H 73 Mouse EHE Network adapters BEES NETGEAR FASO Fast Ethemet CardBus Card F PCMCIA socket H Ports COM amp LPT E M Sound video and game controllers System devices m Universal serial bus controller Double click on Network adapters and then double click on NETGEAR FA510 Fast Ethernet CardBus Card If there is a problem with the installation of the driver an exclamation point appears next to NETGEAR FAS510 Fast Ethernet PCI Adapter If there is an exclamation point double click on NETGEAR FA510 Fast Ethernet PCI Adapter Model FA510 Network Card Installation Guide NETGEAR FA510 Fast Ethernet CardBus Card Propert The Properties window opens and a message regarding the status of the device is displayed in the window Continue to click on OK or click on the X in the right hand corner to close any open windows and return to the Windows 98 desktop Model FA510 Network Card Installation Guide Technical Specifications Model FA510 Network Card Standards Compatibility NetWare tested and approved Microsoft Windows 95 Windows 98 Windows NT compatible IEEE 802 31 10BASE T Ethernet IEEE 802 30 100BASE TX Fast Ethernet 200 8 56 by 5 40 cm weg Environmental Specifications Opening temperatur o
4. Update Device Driver Wizard EH Up NETGEAR FAS10 Fast Ethernet CardBus Card N Windows has finished installing the software that your new hardware device requires Click on Finish 12 Network To finish setting up your new hardware you must restart your computer Do you want to resatrt your computer now Be sure to remove the Drivers and Diagnostics Disk and the Windows 98 CD ROM before restarting your computer Click on Yes to restart your computer 13 Proceed to Verify Installation Model FA510 Network Card Installation Guide Printers Control Panel E Control Panel Dial Up Scheduled Tasks Networking ontrol Panel Use the settings in Control Panel to personalize your computer Select an item to view its description Microsoft Home Technical Support fe 5 Accessibility Options Game Controllers Modems Power Management Add New Hardware Infrared Mouse Printers Add Remove Date Time Programs Internet Keyboard Multimedia Network Regional Sounds Settings m E Microsoft Mail Postoffice Passwords Double click on My Computer on your desktop double click on Control Panel and then double click on System 2 System Properties Device Manager Hardware Profiles Performance Click on Device Manager Model FA510 Network Card Installation Guide System Properties
5. or click Next to continue Location of driver z A NETFAS510 INF Make sure that the location and the correct driver are displayed for example A NETFA510 INF Click on Next Insert Disk Please insert the the disk labeled NETGEAR FA510 Fast Ethernet CardBus Card Drivers Disk and click OK Click on OK Model FA510 Network Card Installation Guide Copying Files The file NDIS2DOS FA510 DOS on NETGEAR FA510 Fast Ethernet CardBus Card Drivers disk cannot be found Insert NETGEAR FA510 Fast Ethernet CardBus Card Drivers disk in the selected drive and click OK Skip File Copy files from Insert the Drivers and Diagnostics Disk and click on OK Note If you copied the Windows 98 CD ROM to your hard drive the next two screens may not appear Insert Disk Please insert the the disk labeled Windows 98 CD ROM and then click OK Click on Copying Files The file choosusr dil on Windows 98 K CD ROM could not be found Cancel Insert Windows 98 CD ROM into the drive selected below and click OK Skip File Copy files from Details D WIN98 Browse Insert the Windows 98 CD ROM Make sure the designated path to the Windows 98 CD ROM is displayed in the files from prompt line for example D WIN98 Click on Model FA510 Network Card Installation Guide 11
6. radio TV technician for help EN 55 022 Statement This is to certify that the Model FA510 Network Card is shielded against the generation of radio interference in accordance with the application of Council Directive 89 336 EEC Article 4a Conformity is declared by the application of EN 55 022 Class B CISPR 22 Compliance is dependent upon the use of shielded data cables Canadian Department of Communications Radio Interference Regulations This digital apparatus Model FA510 Network Card does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications Reglement sur le brouillage radio lectrique du ministere des Communications Cet appareil num rique Model FA510 Network Card respecte les limites de bruits radio lectriques visant les appareils num riques de classe B prescrites dans le R glement sur le brouillage radio lectrique du minist re des Communications du Canada Model FA510 Network Card Installation Guide NETGEAR NETGEAR Inc 4500 Great America Parkway Santa Clara CA 95054 USA Phone 1 888 NETGEAR E mail support NETGEAR com www NETGEAR com M F A 5 1 0 N A 1 Model FA510 Network Card Installation Guide
7. mpliance Notice Radio Frequency Notice This device complies with part 15 of the FCC Rules Operation Declaration of Conformity is subject to the following two conditions NETGEAR Model FA510 Network Card 1 This device may not cause harmful interference FE 2 This device must accept any interference received including eR es interference that may cause undesired operation FOR HOME OR OFFICE USE Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced
8. pe unii Agency Compliance Canada ICES 003 Class B VCCI Class B Model FA510 Network Card Installation Guide 2000 by NETGEAR Inc All rights reserved Trademarks NETGEAR is a trademark of NETGEAR Inc Windows is a registered trademark of Microsoft Corporation Other brand and product names are trademarks or registered trademarks of their respective holders Information is subject to change without notice All rights reserved Statement of Conditions In the interest of improving internal design operational function and or reliability NETGEAR reserves the right to make changes to the products described in this document without notice NETGEAR does not assume any liability that may occur due to the use or application of the product s or circuit layout s described herein Certificate of the Manufacturer Importer It is hereby certified that the Model FA510 Network Card has been suppressed in accordance with the conditions set out in the BMPT AmtsbIVfe 243 1991 and Vfg 46 1992 The operation of some equipment for example test transmitters in accordance with the regulations may however be subject to certain restrictions Please refer to the notes in the operating instructions Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right to test the series for compliance with the regulations Federal Communications Commission FCC Co
9. ppable which means it can be inserted into a PC that is either turned off or powered on 1 Insert the Model FA510 Network Card into the CardBus slot as illustrated in the figure Some PCs have two CardBus slots The Model FA510 Network Card can be inserted into either slot 2 Insert the RJ 45 adapter cable into the connector on the edge of the network card 3 Insert the Category 5 10 100 Mbps UTP cable into the RJ 45 adapter cable Model FA510 Network Card and RJ 45 adapter cable 9025FA 4 If you have chosen to install the card with the power turned off turn on the power to the PC Model FA510 Network Card Installation Guide Connect the Network Cables 1 Usinga UTP cable connect any port on the hub to the port on the RJ 45 adapter cable To connect the network cables follow the illustration below Note One of the ports on NETGEAR hubs is switchable between Normal MDI X and Uplink MDI with a Normal Uplink push button If you are using this switchable port on a NETGEAR hub to connect to a PC or the network card make sure the Normal Uplink push button is set to Normal PC with network Power adapter Notebook PC card installed RJ 45 connectors Model FA510 Network Card with RJ 45 adapter cable Category 5 10 100 Mbps UTP cables Use the cable provided or any Category 5 UTP cable Maximum length 100 meters 300 feet 9026FA Model FA510 Network Card Installation Guide
10. ram that makes a hardware device work Click on Next Model FA510 Network Card Installation Guide Add New Hardware Wizard What do you want windows to do e Search for the best driver for your device Recommended O Display a list of all the drivers in a specific location so you can select the driver you want Select Search for the best driver Click on Next Add New Hardware Wizard Windows will search for new drivers in its driver database on your harddrive and in any of the following selected locations Click Next to start the search Floppy disk drives CD ROM drive Microsoft Windows Update E Browse Select Floppy disk drives Select Specify a Location and make sure the location is Insert the Drivers and Diagnostics Disk into the floppy drive and click on Next Model FA510 Network Card Installation Guide Add New Hardware Wizard Windows has found an updated driver for this device and also some other drivers that should work with this device What do you want to install The updated driver Recommended NETGEAR FA510 Fast Ethernet CardBus Card One of the other drivers Add New Hardware Wizard Windows driver file search for the device NETGEAR FA510 Fast Ethernet CardBus Card Windows is now ready to install the best driver for this device Click Back to select a different driver
Download Pdf Manuals
Related Search