Nady Systems ADI-2 User's Manual
Contents
1. SERVICE FOR YOUR NADY AUDIO PRODUCT O U S Should your NADY AUDIO product require service please contact the Nady Service pa LOIC D Department via telephone at 510 652 2411 or e mail at service nady com OWNER S MANUAL International For service please contact the NADY AUDIO distributor in your country through the dealer from whom you purchased this product DO NOT ATTEMPT TO SERVICE THIS UNIT YOURSELF AS IT CAN BE DANGEROUS AND WILL ALSO VOID THE WARRANTY ah UJ LOIC OSO NADY SYSTEMS INC 6701 SHELLMOUND STREET EMERYVILLE CA 94608 Tel 510 652 2411 Fax 510 652 5075 www nady com 2 Channel Active Direct Inject Box Operation peration Connected to Instrument The ADI 2 can be used to connect the unbalanced output of an instrument or line level device eg guitar bass synthesizer effects module another mixer to the balanced input of a mixer or amplifier Setthe GUITAR SPEAKER 3 switch to GUITAR for this application If you desire to send the original unbalanced signal on to a mixer or amplifier use the 1 4 unbalanced output 5 The 1 4 output 5 is paralleled with the input therefore when using the 1 4 output 5 the input device and output device volume controls may need to be adjusted to acquire the desired level Connected to Amplifier The ADI 2 can be used to connect an amplifiers speaker output or a speaker s daisy chain output to the balanc2. ed input of a mixer Set the GUITAR SPEAKER 3 switch to SPEAKER for this application If your speaker has only one connector the ADI 2 can be inserted between the amplifier and speaker using the 1 4 input 4 and 1 4 LINK OUTPUT 5 jacks Specifications _ pecifications Frequency Response nase ee 10Hz 30KHz 3dB Input Impedance Guitar coin mn Bene an a 780k ohms Input Impedance Speaker ooooooooooooccccoooccccononocononcconononccononononononoconononccnonoss 10k ohms Output Impedancer 2 n een een 470 ohms Maximum Output see sa 2dBv 980mV A A eau ei tunel detonate tone 0 02 SIN ne a ee el AETA ah ne Dac ta 108dB IN PIOOK sissies ee ee es A ee AuV IES A anne scher ea er tn See A ae te A ee 101dBu A een ende 2 Unbalanced 1 4 Phone Jack ODU oe ae csc ee 2 Balanced XLR Connector QUID st ea 2 Unbalanced 1 4 Phone Jack Power Requirement ennen 9 Volt Battery or Phantom Power 24 48 VDC CUNETA tas 10mA A O ewaatdlcc honing Gis paandencesennsdeehe ana Bees 0 98 Ibs 36 kg DIMENSION cuicos lodos ea 5 X 3 7 x 2 2 127 x 94 x 51mm 5 Introduction ntroduction Congratulations for purchasing the ADI 2 2 Channel Active Direct Inject Box This unique unit is the ultimate multi functional active DI box The ADI 2 is indispensable for solving many audio mismatch and hum problems in numerous stage and studio applications e Simultaneous dual inputs and outputs for stereo
3. has 25V 48V phantom power enabled the ADI 2 can be used without draining the 9V battery Disabling the ON OFF button will save battery power when using phantom power Always remember to turn off the ADI 2 ON OFF switch when not in use to preserve your battery CAUTION Always turn on the ADI 2 before turning up the volume on devices connected to the ADI 2 outputs to avoid damaging your equipment or speakers 2 GROUND LIFT SWITCH When set to LIFT this disconnects the ground connection between the 1 4 input and XLR output to eliminate hum caused by ground loops 3 SPEAKER GUITAR BUTTON When pushed in this enables a 35dB pad allowing the input to receive high level signals from speaker or amplifier outputs 3 E NADY SYSTEMS INC Emeryville California USA AD amp Made in China SYSTEMS L L tS R R C A 7 4 5 4 5 4 1 4 INPUTS Unbalanced 1 4 input jack for inputting a line level instrument level or speaker level signal 5 1 4 LINK OUTPUTS Unbalanced 1 4 output jack which is in parallel with the input jack This allows the ADI 2 to be used as a Y splitter by sending the input signal to another device via the 1 4 output as well as sending it from the balanced XLR output 6 XLR OUTPUTS Balanced XLR output jack Pin 1 Ground Pin 2 Hot Pin 3 Cold 7 BATTERY COMPARTMENT Remove screw and panel to install 9V battery
4. or multi source use e Eliminates impedance mismatch problems and converts any sound source at almost any level from guitar to speaker into a clean powerful hum free noise free and interference free balanced signal perfect for even extremely long cable runs e Full featured controls and connections include On Off Ground Lift and Guitar Speaker Source Select input attenuation switches unbalanced 1 4 TS Input and Parallel Link Output jacks and servo balanced XLR Output jack e Parallel link output allows ultimate hookup flexibility by enabling applications such as connection to the input of the backline or monitor amplifier e No compromise circuit design and stringent component selection provide absolutely flat full frequency response across the entire audio spectrum and negligible distortion for the most natural powerful audio available e Portable aircraft aluminum extruded case for ultimate roadworthiness long life and reliability e Powered either by console s 48V phantom power or internal 9V battery Contents A Seen E see 2 Controls ana Connec ione ar eliotn E Dale R 3 A A eects ee E 4 Gonnecled ie lnstumen ansehe 5 CONE c EO AMP ehesten 5 OSC MIG 0 y ESPACIO PO OE N 5 Controls and Connections and Connections 2 9V BATTERY 1 ON OFF SWITCH When set to ON this enables the 9V battery power for the unit If the device connected to the ADI 2 XLR output
Download Pdf Manuals
Related Search