MTD 439-305 User's Manual
Contents
1. 1 2 13 Description 371 2075 and bearings Bearings in Hopper 10 24 x 3 8 Lg Truss Hd Mach Sew 8 10 24 Square Nut 14 3 32 x 3 4 Lg Cotter Pin 2 Drive Wheel with tire 305 1387 20 2 710 192 20 712 425 714 507 20 503 4009 2 30 3 20 4 5 6 710 473 20 7 8 9 310 2080 90 716 508 20 310 2083 80 Shutter Bar Clevis Clip Control Rod 10 503 4006 2 30 Free Wheel with Tire 11 712 148 20 10 24 Wing Nut 12 736 147 20 No 10 External Lock Washer 5 13 305 2091 30 Grip Handle 14 312 2081 1 00 Handle 15 312 2087 1 00 Leg 2 16 736 235 20 Flat Washer 2 17 732 497 50 Spring 18 710 144 20 10 24 x 1 4 Lg Rd Hd Mach Sew 2 19 720 500 30 Grip Control Rod 20 310 4357 50 Indicator Bracket 21 310 2084 50 Control Bracket 1 50 Screw Pack Not shown in illustration Available locally ASSEMBLY INSTRUCTIONS Attach top hole of legs to hooper with 3 8 long bolts and nuts Lap arms over legs as shown and fasten with two 3 8 long bolts and two bolts and nuts Assemble control bracket and indicator as shown in diagram A Slip control bracket on handle and fasten with the two 1 long bolts and nuts Do not reverse control bracket Secure handle to arms with two 114 long bolts and nuts Washer spring washer should be on rod as shown Insert this i2. should open evenly and be snug on entire length of hopper If adjusting your shutter becomes nece ssary invert the spreader and loosen the four bolts slightly Tap shutter into correct position and retighten Shutter opening should be 14 at 8 indi cator setting 2 R VOS Pa ON ha 4 P O BOX 2741 e CLEVELAND OHIO 44111 UTRO IN U S A PRINT NAME IMPORTANT USE THIS CONVENIENT ORDER BLANK Fill in complete data requested on this form to assure that your order will be shipped promptly A new instruction sheet will be returned with the parts you order Street or R F D City NOTE Add 30 for postage and handling on all orders of 2 00 or less On orders of more than 2 00 add 15 for postage and handling MINIMUM ORDER 1 00 IMPORTANT Be certain your name and address are on your order An amazing number of orders are in the no name file and cannot be shipped until we get a letter of complaint If you have any reason to be dissatisfied advise or give us a chance to make things right We genuinely try to give satisfaction REMITTANCE Payment in full should accompany all orders Money Order Check or Bank Draft are recommend ed Avoid sending cash unless absolutely necessary If you send cash wrap it in heavy paper and REGISTER YOUR LETTER Sorry no C O D s PRICES are subject to change without notice INSPEGTOR NUMB
3. ER Total Amount Required yA Droga an R a a a OLD a This item is guaranteed to be free of defects in workmanship and or materials Under this warranty MTD Products Inc is limited to the replacing of any part or parts which shall be returned postpaid and which our examination shall disclose to have been defective Any part or parts which are damaged by misuse or accident in handling are not covered by this warranty 7 THIS CARTON WAS INSPECTED IF THERE ARE ANY SHORTAGES PLEASE REFER TO THE ABOVE a a m a A A 4 A ONO OS 05 WARRANTY VOEE EE EEEIEI EEIE E Defective parts or shortages must be reported to the factory immediately Such claim should be reported on this form and must be accompanied by the following information 1 Equipment name and model number 2 Date of purchase 6 3 Part number and description of part 4 Description or nature of defect Do not forward any payment with a warranty or shortage cla im The factory will advise you if payment is due MTD PRODUCTS INC gt 5389 WEST 130th ST e P O BOX 2741 CLEVELAND OHIO 44111 PRINTED IN U S A
4. nto control bracket from bottom and swing rod into position Straddle clip over shutter bar hole Slip rod thru clip and shutter bar Then swing clip up on rod This must be on as shown in order to have free shutter action Complete assembly by adding both grips MTD PRODUCTS INC FORM NO 770 1873 PARTS LIST FOR SPREADER MODEL 439 305 No Required Per Assembly Hopper Complete with Agitator axle 10 24x Lg Truss Hd Mach Sew 2 22 710 467 20 10 24x 1 Lg Truss Hd Mach Sew 2 23 312 2082 50 Handle Braces 2 312 80 Pivot Bracket 2 5389 WEST 130th ST e 10 CENTS CLOSED Spreader should always be in closed position when setting is made or when loading hopper When rod is off indicator hook and down it s in closed position Make setting by sliding indicator to desired opening and tightening wing nut When ready to operate just hook rod on indicator e To determine setting refer to chart Some experimentation may be necessary be cause of variations of different products CARE OF SPREADER Before putting spreader away flush hopperg agitator and shutter with water If seed is used washing is not necessary Cover bottom of hopper with a light film of oil to prevent corrosion When spreader is not in use store in closed position This prevents prolonged tension on spring Avoid using damp materials or exposing spreader to rain Shutter
Download Pdf Manuals
Related Search