Moxa Technologies V481-XPE User's Manual
Contents
1. In addition both USB ports support system boot up which is activated by changing BIOS settings Audio Interface The ThinkCore V481 has an audio interface that follows the AC97 standard and supports speaker output and audio line input Speaker Audio Output Input 4 Power On Off Button The power on off button is located above the power input terminal block The button supports the ATX power on off function By default the button is set for instant off You may also configure the button for delay 4 seconds to guard against shutting down the power unintentionally In this case you must press the power button continuously for at least 4 seconds to shut off the power Reset Button The reset button is designed to warm reboot the V481 Pressing the Reset button initiates a hardware warm reboot The button plays the same role as a desktop PC s reset button After pressing the reset button the system will reboot automatically During normal use you should NOT use the Reset Button You should only press the Reset Button if the software is not working properly To reset the system work from the operating system environment by using the corresponding software reboot function to protect the integrity of data being transmitted or processed Real time Clock The embedded computer s real time clock is powered by a lithium battery We strongly recommend that you NOT replace the lithium battery yourself If2. 10 100 1000 Mbps Ethernet ports use RJ45 connectors Pin Signal m _ ERx ERx orig Pors Fa em The serial ports use DB9 connectors Each port can be configured by software for RS 232 RS 422 or RS 485 The pin assignments for the ports are shown in the following table RS 485 RS 485 bad ore Bone 4 wire 2 wire a xb fsb bac 3 TxD RxDB RxDB DataB 5 GND GND GND GND 6789 SO DIMM Socket for Memory Module The ThinkCore V481 has an internal 200 pin SO DIMM socket for installing a DDR SDRAM memory module The V481 XPE comes with a 512 MB DDR SDRAM Module pre installed You may also replace the module with your own 128 MB to 1 GB DDR SDRAM memory module To replace the module first remove the bottom cover of the V481 to expose the SO DIMM socket Compact Flash Socket The ThinkCore V481 XPE comes with a built in 1 GB industrial CompactFlash card to store the WinXP Embedded operating system A second CompactFlash socket is located inside the V481 Installing a second CompactFlash memory card will not affect the operating system Remove the bottom cover of the V481 to install the second CompactFlash card USB Hosts The ThinkCore V481 supports two USB 2 0 hosts Both hosts are UHCI Rev 2 0 compliant and support Plug amp Play and also hot swapping Both hosts can be used to connect any USB device such as a keyboard mouse USB flash disk or USB CD ROM
3. Core V481 Panel Layout The following figures show the panel layouts of the ThinkCore V481 P N 1802004810020 Rear View Power Button Power Input 9 36 VDC Serial Ports x 8 RS 232 422 485 Front View Speaker Audio USB 2 0 10 100 Mbps Power LED Output Input Hostx 2 Ethernet 10 100 1000 Mpbs Gigabit Ethernet Storage LED Reset VGA PS 2 LED Indicators There are 6 LED indicators located on the front panel of the ThinkCore V481 LED Name LED Color LED Function Power off No power is being received or power error exists Li Data is being written to or read Yellow Blinking 8 Storage form the storage unit Storage unit is idle LAN 1 exists LAN 2 1000 Mbps Ethernet Mode LAN2 Only Gigabit Ethernet MOR cd 100 Mbps Ethernet Mode 10 Mbps Ethernet Mode 4 Installing the ThinkCore V481 Wall or Cabinet Mounting The ThinkCore V481 has built in ears for attaching the embedded computer to a wall or the inside of a cabinet We suggest using two screws per ear DIN Rail Mounting An aluminum DIN Rail mounting kit is a standard accessory If you need to reattach the DIN Rail mounting kit to the ThinkCore V481 make sure the stiff metal spring is situated towards the top as shown in the following figures Follow Steps 1 and 2 to mount the V481 on the DIN Rail STEP1 Insert the top of the STEP2 The DIN Rail attachment DIN Rail into the slot just below the unit will snap into place as shown stiff meta
4. MOXA ThinkCore V481 XPE Quick Installation Guide First Edition November 2007 1 Overview The ThinkCore V481 is an industrial ready to run embedded computer that supports VGA and audio and comes with dual LAN ports 8 serial ports a CompactFlash slot and a USB port The V481 is based on the Intel x86 processor The VGA interface makes the V481 especially well suited for industrial applications such as SCADA factory automation and applications that require an onsite HMI or monitor 2 Package Checklist Before installing the ThinkCore V481 verify that the package contains the following items e ThinkCore V481 e Quick Installation Guide this guide e Document and Software CD e Din rail Mounting Kit e 100 cm RJ45 to RJ45 Ethernet Cross over Cable e 20cm Y type Cable for Keyboard and Mouse CBL MiniDIN6P 6Px2 20 e Terminal Block to Power Jack Converter includes Terminal Block e Product Warranty Statement Optional Accessories e Switching power adaptor for the ThinkCore V481 60W 24 VDC output 100 to 240 VAC input power cord must be ordered separately Order No 1117224250210 e Power Cords Power cord with Australian plug Order No 1705010700510 Power cord with UK plug Order No 1705010700410 Power cord with Euro plug Order No 1705010700210 Power cord with straight US plug Order No 1705010700110 NOTE Notify your sales representative if any of the above items are missing or damaged 3 Think
5. l spring CIN Rail 1 To remove V481 from Din rail simply reverse Steps and 2 5 Connector Description Power Connector Connect the 9 to 36 VDC LPS or Class 2 power line to the ThinkCore V481 s terminal block If the power is properly supplied the Power LED will light up Grounding the V481 Grounding and wire routing help limit the effects of noise due to electromagnetic interference EMI Run the ground connection from the ground screw to the grounding surface prior to connecting the power EEN ATTENTION This product is intended to be mounted to a well grounded mounting surface such as a metal panel LS toprsiiagntenwires SG The Shielded Ground sometimes called Protected Ground contact is the right most contact of the 3 pin power terminal block j connector as viewed from the angle shown nsert shielded ground here Connect the SG wire to an appropriate V V th ire h ee ae iii grounded metal surface 36 D VGA C o The ThinkCore V481 comes with a D Sub 15 pin female connector to connect a VGA CRT monitor PS 2 Connector The ThinkCore V481 has a PS 2 connector for a PS 2 keyboard or PS 2 mouse connection This 6 pin mini DIN connector has the following pin assignments 1 PS 2 keyboard data GND PS 2 keyboard clock 6 PS 2 mouse clock A Y type cable is included as a standard accessory for connecting a PS 2 keyboard and PS 2 mouse at the same time Ethernet Ports Both the 10 100 and
6. sk click OK Copyright 2007 Moxa Systems Co Ltd All rights reserved Reproduction without permission is prohibited MOXN Tel 886 2 2910 1230 www moxa com Fax 886 2 2910 1231 support moxa com
7. the battery needs to be changed please contact the MOXA RMA service team 5 ATTENTION There is a risk of explosion if the battery is replaced by an incorrect type of battery 6 Powering on the V481 To power on the V481 connect the terminal block to power jack converter to the V481 s DC terminal block located on the left rear panel and then connect the power adaptor Note that the Shielded Ground wire should be connected to the right most pin of the terminal block It takes about 30 seconds for the system to boot up 7 Starting the V481 Power on the V481 after connecting a monitor keyboard mouse and checking that the power source is ready Once the operating system boots up the first step is to configure the Ethernet interface The factory default settings for the V481 s dual LANs are shown below You can use a cross over Ethernet cable to connect directly from the PC to the V481 to test if the LAN settings are correct Default IP Address LAN 1 192 168 3 127 255 255 255 0 LAN 2 Gigabit 192 168 4 127 255 255 255 0 8 Configuring the Ethernet Interface Follow these steps to configure the Ethernet interface Step 1 My Device gt Control panel gt Network Connections to enter the network setting page Step 2 Right Click the LAN interface e g Local Area Connection 2 to configure and click property A configuration window will pop up Step 3 After inputting the proper IP address and netma
Download Pdf Manuals
Related Search