Mitsubishi Electronics P91DW User's Manual
Contents
1. SPECIFICATIONS Type Model Power supply and power consumption Connection terminal Dot resolution Gradation Printing speed Print size Operating conditions External dimensions Weight Standard accessories Optional accessory Digital Monochrome Printer P91DW 120V AC 50 60Hz 1 4A 220 240V AC 50 60Hz 0 8A Parallel data interface 36 pin female type 1024 x 1024 pixels Standard Max 1024 x 5120 pixels 256 gradations 5 1 sec Standard 4 x 4 100mm x 100mm Standard Max 4 x 20 100mm x 500mm Temperature 41 104 F 5 40 C Humidity 20 80 RH No dewing 6 1 x 3 8 x 11 8 154mm x 97mm x 300mm W x H x D 6 8 lbs 3 1kg AC POWer Coli s ici cedet nec iii 1 piece Thermal paper K65HM 1 roll Cleaning paper miii diii 1 sheet Printer driver 1 floppy disk Thermal paper K65HM K65H K61B K61S SERVICE INFORMATION Before requesting service please review this operation manual to correct minor complaints If you are unable to correct the problem consult your MITSUBISHI Dealer or MITSUBISHI Service Department DO NOT ADJUST ANY CONTROLS NOT DESCRIBED IN THIS OPERATION MANUAL DO NOT REMOVE THE PROTECTIVE ENCLOSURE OF THIS UNIT e MITSUBISHI MITSUBISHI ELECTRONICS AMERICA INC 5665 PLAZA DRIVE P O BOX 6007 CYPRESS CA 90630 0007 USA TEL 714 220 2500 FAX 714 236 6339 Mitsubis2. in the function mode print feeding length is shorter than normal condition Before cutting the print press the FEED button on the front panel to advance the paper ADJUSTMENT OF PRINT PICTURE You can select y curve by pressing the gamma button 7 Each time the button is pressed the indicator and y curve number is switched After a y curve number has been selected press the SET button to store the y curve number FUNC O UP SET CSP Indicator Adjustable Item Adjustable contents set m This is the mode to select the gamma y curve density 5 mode diagram characteristic to get the proper density for each printing image Select the best one among the five gamma curves 0 8 SETTING OF FUNCTION MODE Q Select a function mode by pressing the FUNC button Each time the FUNC button is pressed the mode is switched as shown below Standby Y Paper type selection mode Y Paper saving mode Y Set condition printing mode Y L Buzzer set mode Adjust a numeric value by pressing W or A button E Adjustable items of each function mode are as follows Indicator Adjustable Adjustment contents item Paper type Mode to select paper type PH selection s Standard paper mode 4 High density paper 5H Paper saving Mode to select paper saving mode mode Paper saving m
3. Do not pull out the sheet and the cleaning paper while the door is closed Never use other cleaning papers It may cause damage to the thermal head This cleaning paper should be used only for cleaning the thermal head Do not use it for other purpose PARALLEL DATA INTERFACE E PARALLEL TERMINAL SIGNAL Connector JD36SL or equivalent 36 pin Pin number Input level TTL 18 1 Parallel input connector port Signal allocation Signal Compatible iaa 36 19 Pin Return Signal From To Function pin No 19 STROBE Strobe pulse for data reading Incoming pulse width shoud be 0 5us minimum At regular conditions High data will be read after becoming Low DATA1 LSB High data 1 DATA2 Low data 0 DATA4 Information will be expressed for parallel data of every signal DATA5 from bit No 1 to No 8 DATA6 DATA7 DATA8 MSB ACK PC DP The signal is yielded after data input has ended by a data ACKNOWLEDGE reception acknowledgement pulse BUSY PC DP High DP data is not accepted Low DP data is accepted The signal becomes High in the following cases During data entry PC DP High No paper PAPAER END Low Paper available SELECT POP PICTURES GND PC DP Earth High PC DP PeripheralLogicHigh GND INIT PC DP Clears sending data to this unit Low Incoming pulse width should be 100us minimum PC DP Low Abnormal con
4. Press the Cut the printed Ne POWER paper with the gooo switch to turn m cutter by on the power tearing off the ug paper in the upper right direction AES Print a picture displayed on the screen Print a picture with an application software The image data is transferred through parallel data interface Copy printing You can set the number of copies by pressing the COPY button on the front panel You can copy the same picture as many times as you desire until a new image data is printed When the COPY button is pressed during copy printing the current image will be completed and the rest will not be printed Indicator Wi The set number of the copy printing will CX a not be memorized MEA y i 9 number of copies E continuous printing COPY printing mode 41 Paper feeding H By pressing the FEED button on the front panel you can feed the paper Precautions on Printing If printing is continued with a very black picture the printer will become overheated and printing will not be available i is indicated and the button functions become invalid In this case wait for a while until the unit is cooled down Avoid pulling out or holding the recording paper during printing or copying It can cause paper jam Do not touch the paper until printing or copying ends Paper saving mode Bl When the paper saving mode switch is set to
5. s MITSUBISHI C DIGITAL MONOCHROME PRINTER MODEL P91DW OPERATION MANUAL THIS OPERATION MANUAL IS IMPORTANT TO YOU E PLEASE READ IT BEFORE USING YOUR DIGITAL MONOCHROME PRINTER DIGITAL MONOCHROM PRINTER This digital monochrome printer complies with the requirements of the EC Directive 89 336 EEC 73 23 EEC 93 42 EEC and 93 68 EEC The electro magnetic susceptibility has been chosen at a level that gains proper operation in residential areas on business and light industrial premises and on small scale enterprises inside as well as outside of the buildings All places of operation are characterised by their connection to the public low voltage power supply system WARNING Use the AC power cord recommended as below and a parallel cable Hewlett Packard C2951A etc so as not to interfere with radio and television reception If you use other cables it causes interference with radio and television reception WARNING Use the AC power cord according to the recommendations as below Case 1 2 3 and 4 in order to comply with UL2601 1 and CAN CSA C22 2 No 601 1 Case 5 in order to comply with EN60601 1 and EN60950 Case 1 Connect to the 120V receptacle of the room or the host equipment The AC power cord should be UL or CSA approved and consist of type SJT size 16 or 18AWG length 2 5m or shorter cord with IEC320 C13 type 125V 10A or higher rating connector and NEMA 5 15 type
6. Symptom Remedy Button input Symptom error e An alarm tone is given once is displayed for one second in the indicator and button operation is nullified in the following cases The COPY button is pressed first after the power is turned on The DOWN UP SET or GAMMA button is pressed when the MODE switch No 1 is set to ON Any button on the front panel is pressed when one of the other error messages is displayed on the LED LL Cause Error display Symptom Remedy Door error Symptom When the door opens an alarm tone is given Remedy Close the door Cause Error display Symptom Remedy O Gear lock error Symptom When the thermal head does not automatically go up after printing an alarm tone is given e Ei is displayed in the indicator and all the functions of buttons I and switches become invalid Remedy Turn the power off Then turn it on again STATUS AND MODES LED display Contents of right Pointand side LED displa Left ight play Set state Mode Power off Power off Stand by Print state 5 x During data receiving During printing Copy state Number of copies y curve set mode y curve 5 y curve No Paper type setting mode p Standard High density Paper saving mode Out In OFF ON Set condition printing mode Out In OFF ON Buzzer
7. 125V 10 or higher rating Hospital Grade plug Case 2 Connect to the 230V receptacle of the room or the host equipment The AC power cord should be UL or CSA approved and consist of type SJT size 16 or 18AWG length 2 5m or shorter cord with IEC320 C13 type 250V 10A or higher rating connector and NEMA 6 15 type 250V 10 or higher rating Hospital Grade plug Case 3 Connect to the 120V receptacle of the host equipment The AC power cord should be UL or CSA approved and consist of type SJT size 16 or 18AWG length 2 5m or shorter cord with IEC320 C13 type 125V 10A or higher rating connector and IEC320 2 2 E type 125V 10 or higher rating plug Case 4 Connect to the 230V receptacle of the host equipment The AC power cord should be UL or CSA approved and consist of type SJT size 16 or 18AWG length 2 5m or shorter cord with IEC320 C13 type 250V 10A or higher rating connector and IEC320 2 2 E type 250V 104A or higher rating plug Case 5 Connect to the 230V receptacle of the room or the host equipment The AC power cord should be VDE approved and consist of core size 1mm or bigger length 2 5m or shorter cord with 1EC320 C13 type 250V 10A or higher rating connector and CEE 7 VII type or IEC 320 2 2 E type 250V 10A or higher rating plug NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protecti
8. BLE LOCATIONS Avoid shaky places or hot springs areas where hydrogen sulfide and acidic ions are likely to be generated PLACES WITH HIGH HUMIDITY AND DUST Do not place the unit at locations with high humidity and or dust They can cause extensive damage Avoid places where the unit is likely to contact oily fumes and vapors PLACES NOT LIKELY TO BE EXTREMELY HOT Places exposed to direct sunlight or near heating appliances can attain extremely high temperatures which may deform the cabinet or can become a prime cause of damage SET THE UNIT ON A FLAT PLACE Do not use the unit in the state inclined 20 in vertical or horizontal direction or in an unstable place It will disturb paper feeding or ventilation or affects the set FOR LONG OPERATING LIFE UNSUITABLE MATERIALS FOR THE UNIT Many plastic components are used in the backside Coat flaking and deformation are likely to occur if the unit is wiped with chemical dusters benzine thinner or any other sol vent if rubbers or PVC items are left in contact with the unit for extended duration or if the unit is sprayed with insecticide CARE OF THE CABINET Unplug and clean with a soft cloth slightly moistened with a mild soap and water solution Allow to dry completely before operating Never use petroleum base solutions or abrasive cleaners HEAD ABRASION The thermal head like the video head wears out When it is abraded it becomes hard to print out fine detai
9. a interface such as medical equipment and personal computer Connection CD Turn off the power switches of the digital monochrome printer and the equipment to be connected Connect the digital monochrome printer with PC or medical equipment through a parallel cable When inserting the parallel cable to the printer s connector make sure to fasten the springs at the both sides of the connector to secure the cable Personal computer or medical equipment To PARALLEL DATA IN connector T Connect vo Power cord Rear panel Mode switch setting Set the mode switches on the rear panel il When setting the switch No 1 to ON FUNC DOWN UP SET and ON GAMMA buttons will be locked The functions will not be available orr 3 Set the switches other than No 1 to OFF Installing printer driver Printer driver is required to print the data from a personal computer connected with this printer The printer driver for Windows is supplied with this printer Product name Operating conditions For Windows Applies for Microsoft WindowsNT 4 0 Refer to the operation manual of the printer driver or Read me for installing WindowsNT is the registered trademarks of Microsoft Corporation in the U S A and other countries PRINTING Turn on the power Cut the printed paper Printing procedure
10. dition occurs in DP e g error ES a es 33 35 s m DP Digital printer PC Personal computer Parallel input connector port Signal allocation Signal Nibble HostClk PC DP High PC DP Unknown PC DP Sends data in Low when HostBusy is Low After HostBusy turns High this signal becomes High PtrBusy PC DP Data4 Data8 MSB AckDataReq PC DP Data3 Data7 Data2 HostBusy PC DP High DP is on BUSY status Low DP can send data 19 30 GND Earth LANE EE Clears sending data to this unit Low Incoming pulse width should be 100us minimum 32 bata val PC DP Datat LSB Data5 EE HEN Aa 33 35 36 1284 Active PC DP Becomes High when DP requests each mode of IEEE1284 Parallel input connector port Signal allocation Signal ECP Pin No Return Signal From To Function No HostClk Forward data transfer Becomes Low when PeriphAck is Low and there is data to be read Returns to High when PeriphAck becomes High DATA1 LSB High data 1 DATA2 Low data 0 DATA3 DATA4 Information will be expressed for parallel data of every signal DATA5 from bit No 1 to No 8 DATA6 DATA7 DATA8 MSB PeriphClk PC DP Reverse data transfer Sends Low data when HostAck is Low Returns to High when HostAck becomes High PeriphAck PC DP Forward data transf
11. e Wi Store the printed paper in a place with low humidity free from a direct sunlight Wi i the paper absorbs nonvolatile organic solvents alcohol ester ketone etc the print may be discolored Particularly if the paper comes in contact with soft vinyl chloride such as a transparent tape it quickens discoloration Do not use paper other than the specified one Immediately after the paper is replaced 2 3 images may be printed with a blank part due to hand s dust or oil Avoid a direct sunlight or a place near a heater and store the paper in a place with 30 C 86 F or lower temperature and 35 80 RH When the paper is rapidly transferred from a cool place to a hot place a vapor or a dew is generated on the paper surface causing paper jam or degraded printing quality W A finger print or dust on the paper surface may degrade the printing quality Note Mitsubishi brand thermal paper is specially treated with an antistatic coating against thermal head damage caused by static electricity discharge The use of non treated paper may cause premature head failure in your product SAFETY TECHNICAL CHECKS Periods According to the recommendations of the manufacturer of medical device Scope a Visual check Housing cables operator controls readout device displays LED etc labels accessories instruction manual b Function test Performance check acc instruction manual also unity and applicab
12. er High DP is on BUSY status Low DP can accept data 26 27 28 29 AckReverse PC DP High Forward data transfer Receive Low Reverse data transfer Send PC DP High During supporting ECP mode HostAck PC DP Reverse data transfer High PC is on BUSY status Low PC can send data 1617 eno 19 30 Ea TUS Earth Soo FOR Low When DP requests PC to send data 33 35 36 1284Active PC DP Becomes High when DP requests each mode of IEEE1284 2 3 4 5 6 T 8 9 10 11 MAINTENANCE Turn off the power for maintenance Maintenance of Main Unit Wipe off stains of the front panel with a soft cloth When the panel is heavily stained wipe of with the cloth moistened with neutral cleanser diluted by water and finish with a dry cloth Maintenance of Rubber Roller When the rubber roller is dirty with dust etc a black spot may appear on the print In this case eliminate the dust on to the rubber roller with a blower or a brush Rubber roller Cleaning of Thermal Head When the thermal head is dirty with dust etc white spots or stripes may appear on the print In this case clean the thermal head according to 12 USE OF CLEANING PAPER Note After installation of new roll of paper dust on the paper will generally require 2 to 3 prints to be made before the dust is eliminated
13. having a different voltage or fre quency WARNING THIS APPARATUS MUST BE EARTHED AVERTISSEMENT CET APPAREIL DOIT ETRE MIS A LA TERRE This equipment is classified as class 1 type B according to the type of protection against electric shock PROTECTIVE MEASURES IF ABNORMALITIES ARISE Use of the unit during emission of smoke or abnormal sounds without adopting countermeasures is dangerous In such a case unplug the power cord from the source outlet immediately and request maintenance services from the sales dealer NEVER INSERT ANY OBJECT INTO THE UNIT Foreign objects of any kind inserted into this unit consti tute a safety hazard and can cause extensive damage If any object should be inserted into the unit unplug the power cord then contact the sales dealer DO NOT PLACE ANYTHING ON THE UNIT Heavy objects placed on the unit can cause damage or obstruct proper ventilation PROTECT THE POWER CORD Damage to the power cord may cause fire or shock haz ard When unplugging hold by the plug only and remove carefully Never put a heavy thing on the power cord The cord may be damaged causing a fire or electric shock DO NOT PLACE WATER CONTAINERS ON THE UNIT Do not place flower vases and other water holding con tainers on the unit If for some reason water seeps to the inside of the unit unplug the power cord from the Source outlet and contact the sales dealer If used without corrective measures
14. hi Electric Europe B V UK Branch Travellers Lane Hatfield Herts AL10 8XB England U K Phone 1 707 276100 FAX 1 707 278755 German Branch Gothaer Strasse 8 Postfach 1548 40880 Ratingen 1 Germany Phone 2102 4860 FAX 2102 486 732 French Branch 25 Boulevard des Bouvets 92741 NANTERRE cedex Phone 01 55 68 55 00 FAX 01 55 68 57 31 Italian Branch Centro Direzionale Colleoni Palazzo Perseo Ingresso 2 Via Paracelso 12 20041 Agrate Brianza Milano Italy Phone 039 60531 FAX 039 6057694 Benelux Branch Nijverheidsweg 23 A 3641 RP Postbus 222 3640 AE Mijdrecht Phone 02972 82461 FAX 02972 83936 Spanish Branch Barcelona Sucursal en espafia Pol gono Industrial Can Magi Calle Joan Bucall 2 4 Apartado de Correos 420 08190 Sant Cugat del Vall s Barcelona Spa n Phone 93 5653154 FAX 93 5894388 Manufactured by Mitsubishi Electric Corporation 1 Zusho Baba Nagaokakyo City Kyoto Japan Made from recycled paper 871C590A6 PRINTED IN JAPAN
15. ility of set and accessory test C Electrical check Safety electrical test of the configuration in accordance with EN60601 1 n the interest of safety avoid the handling of liquids beside the set RESPONSIBILITY OF THE MANUFACTURER The manufacturer assembler installer or importer considers himself responsible for the effects on safety reliability and performance of the EQUIPMENT only if assembly operations extensions readjustments modifications or repairs are carried out by persons authorized by him and the electrical installation of the relevant room complies with the IEC requirements the EQUIPMENT is used in accordance with the instructions for use Any service after expiration of the warranty period will be made at cost Consult our service station in your place TECHNICAL DESCRIPTION The supplier will make available on request such circuit diagrams component part lists descriptions calibration instructions or other information which will assist the USER s appropriately qualified technical personnel to repair those parts of the EQUIPMENT which are classified by the manufacturer as repairable The use of ACCESSORY equipment not complying with the equivalent safety requirements of this equipment may lead to a reduced level of safety of the resulting system Consideration relating to the choice shall include use of the accessory in the PATIENT VICINITY evidence that the safety certifica
16. it Cutter Printed paper will come out through this slot Cut the printed paper here 9 Lever Opens the door Rear Panel PARALLEL DATAIN Name POTENTIAL EQUALIZATION TERMINAL This is used to equalize the potential of the equipment connected to this unit For details refer to the installation instruction of equipment to be connected Function Mode switches Select special functions PARALLEL data terminal Connects to the device equipped with parallel data interface such as personal computer Power terminal AC LINE Connect the power cord to this terminal Potential equalization terminal Makes the connected equipment of potential equal INSTALLATION OF PAPER Moisture fingerprints or dust on the paper surface may cause a noise at Pull out the paper end printing or deterioration in print quality Set the paper in the following procedure to prevent adhesion of Pull out the first 15 fingerprint or dust on the paper y 20cm 6 in 9 in of surface Y the paper to remove any slack in the roll Open the door Switch the lever located on the left side to the OPEN position m The door opens Place the paper roll in the printer SE INCORRECT CORRECT Note The printing su
17. ls ofthe picture In such a case it is necessary to replace the thermal head Consult with the sales dealer for replacing the head WHEN A DEFECT IS FOUND When you detect smoke or smell from the unit disconnect immediately the power cord plug from a wall socket and ask the agent for repair Dangerous if the unit is operated in that state CONNECTION DEVICES Read thoroughly Operating Precautions of the instruc tion booklets for other devices connected with the Digital monochrome printer Do not disconnect the power cord during printing CAUTION ON RELOCATING When transporting this unit make sure it is not likely to be subjected to impacts They can be a prime cause for dam age Further make sure to disconnect the power cord from the power outlet and the cables from the connected de vices UNPLUG THE POWER CORD DURING A LONG ABSENCE Turn off the MAIN power switch and unplug the power cord during a long absence THERMAL PAPER Wi When the remaining length of the paper is about10 25cm a color belt appears at the paper end Prepare for replacement of the paper If the remaining paper length is less than 10 25cm printing becomes uneven due to the uneven paper core surface When the Printed paper is touched by wet hand the print may be discolored When the paper runs out during printing the printing operation stops and EP is displayed by the indicator on the front panel Install new paper at this tim
18. ode OFF Paper saving mode ON n L Printer condi Mode to select whether the printer conditions will be printed tion printing over the image or not mode 7 The printer conditions are not printed 4 The printer conditions are printed Buzzer set Mode to select whether the buzzer will sound or not mode 5 Buzzer does not sound Sounds only at occurrence of error Buzzer sounds 9 When completing setting the function press the SET button The set functions will not be lost even if the power is turned off ERROR DISPLAY When an error in operation occurs an audible alarm and a visible error is displayed in the LED indicator Cause Error display Symptom Remedy CD No paper Symptom When the paper runs out or the paper is not installed printing becomes impossible and alarm tone is given In this case all the functions of buttons and switches become invalid Remedy Install brand new paper according to 5 INSTALLATION OF PAPER on page 8 Cause Error display Symptom Remedy 2 Overheat Symptom When the head gets overheated cy is displayed on the indicator and alarm tone is given In this case all the functions of buttons and switches become invalid Remedy Wait until the head is cooled down Cause Error display
19. on against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense Information This class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada CLASSIFIED BY UNDERWRITERS LABORATORIES INC O WITH RESPECT TO ELECTRIC SHOCK FIRE AND MECHANICAL HAZARDS ONLY IN ACCORDANCE WITH UL2601 1 AND CAN CSA C22 2 No 601 1 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the litera
20. rface is the outside Cut the paper end with the cutter just like Place the paper with the thermo tearing off the paper sensitive side printing side up When the paper roll is placed inversely images can not be printed E When setting the paper observe the following precautions to prevent paper jam Do not use defective paper E Do not use the bent or wrinkled paper m When the paper is fed out skewed from the print exit adjust the paper X X position so that it is fed out straight Do not slack the roll paper m Set the paper tightly to remove any slack X If the side of the print paper is uneven or the core is sticking out the amount of paper feeding after printing may vary When the side of paper is uneven or the core is sticking out install the print paper after making the paper side even The core is sticking out The paper is uneven Make the paper side even INCORRECT CORRECT CAUTION Keep the high density paper away from fingerprint dust or moisture when storing it Do not touch the rubber roller Do not stain or damage the roller surface Do not touch the thermal head located behind the cutter When printing the thermal head is heated to high temperature Do not touch the cutter blade EXAMPLE OF CONNECTION Connecting to various equipment with parallel dat
21. setting mode Out In OFF ON Overheat No paper Error detect state Button input error Door is open Gear lock USE OF CLEANING PAPER When the thermal head is dirty with dust and perspiration etc white spots or stripes may appear on the print In this case clean the thermal head in the following procedure BY USING THE SUPPLIED CLEANING PAPER Turn on the power Close the door m Press the POWER switch to turn on the power m Close the door without taking out the cleaning paper m Switch the left side lever to the OPEN position Press the FEED button m Roll the cleaning paper and install into the set Cleaning paper Red mark m Adjust the red mark on the cleaning paper parallel to the m Keep pressing the FEED button until you hear a beep Take out the cleaning paper m Open the door m Take out the cleaning paper m Do not pull out the cleaning paper while the door is closed platen roller Platen roller Cleaning paper ES Repeat the steps BH by 2 or 3 times and print 1 2 sheets to verify the cleaning effect CAUTION This may cause extensive damage on the unit It is recommended that after printing 10 rolls of paper the unit be cleaned using the supplied cleaning paper If the symptom of the dirty head is not corrected even after cleaning your set needs repairing contact your dealer
22. the unit may be damaged DO NOT REMOVE THE CABINET Touching internal parts is dangerous besides it may lead to malfunction Contact the sales dealer to carry out inter nal checks and or adjustments Before opening the cover for eliminating a jammed paper etc be sure to discon nect the power cord plug PLACE THE UNIT ON A HORIZONTAL LEVEL The unit is likely to be affected if it is placed in slanted conditions or in unstable places PROTECT AGAINST DEW FORMATION In extremely cold regions if the unit is moved quickly from an extremely cold place to a warmer one dew is likely to be formed If dew is formed printing is not possible OPERATING AMBIENT TEMPERATURE RANGE The operating ambient temperature range is 5 C 40 C 41 F 104 F and humidity of 20 80 BE CAREFUL AROUND PRINT PAPER EXIT SLIT Do not insert your hand or any material into the paper exit slit during printing Do not touch the cutter blade inside the paper exit slit Otherwise your finger will be injured DO NOT TOUCH THE THERMAL HEAD AND CUTTER Do not touch your hand to the thermal head located in side the unit and the cutter blade The thermal head is heated to high temperature This may cause injury INSTALLATION LOCATIONS MAINTAIN GOOD VENTILATION Ventilation slots and holes are provided on sides of this unit Place the unit on a hard and level surface and locate at least 4 10cm from walls to ensure proper ventilation UNSUITA
23. tion of the ACCESSORY has been performed in accordance to the appropriate EN60601 1 and or EN60601 1 1 harmonized national standard The transportation and storage environmental conditions are Temperature 20 C 60 C 4 F 140 F Humidity 90 RH or less at 40 C 104 F Note The above transportation environmental conditions indicate the storage environmental conditions during transport UNPACKING Take the unit out of the box by the following procedures Make sure to check the contents Open the top of the box Take the unit out of the box carefully Make sure to keep the unit horizontal Remove the cushion above the unit Accessories Thermal paper 49 AC power cord S Cleaning paper Operation manual Printer driver 1 floppy disk FEATURES AND FUNCTIONS Front Panel Name Function Power switch Turns on off the power FUNC button Function mode changes whenever FUNC is pressed DOWN button Press to change the value in function mode UP button Press to change the value in function mode SET button Press to set each function value and y curve Indicator Displays stand by functions and error messages GAMMA button Press to change the y curve FEED button Press to feed the paper COPY button Press for additional copies of the previous printout Print ex
24. ture accompanying the appliance WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE reference purpose not for medical diagnostic purpose FEED This product is to be employed with medical equipment just for CONTENTS B BgSE pw Py Py m m om BRASS ONG CONTENTS me 1 PRECAUTIONS cursada 2 4 UNPACKING 5 FEATURES AND FUNCTIONS Front Panel aa 6 hear Panel 7 INSTALLATION OF PAPER 8 9 EXAMPLE OF CONNECTION 10 PRINTING iniciada 11 12 ADJUSTMENT OF PRINT PICTURE Selection of Gamma y Curve 13 SETTING OF FUNCTION MODE 14 15 ERROR DISPLAY 16 17 STATUS AND MODES 18 USE OF CLEANING PAPER 19 PARALLEL DATA INTERFACE 20 22 nnn nnn nnn nnn 23 SPECIFICATIONS iria e eaa a ud 24 PRECAUTIONS In the interest of safety please observe the following pre cautions POWER REQUIREMENT This Digital monochrome printer is designed for opera tion on 120 220 240V AC 50 60Hz in U S A and Canada 220 240V AC 50 60Hz in Europe Never connect to any outlet or power supply
Download Pdf Manuals
Related Search