Mitsubishi Electronics DX-TL5716U User's Manual
Contents
1. la 00000 Camera number buttons Bl Displaying images in the split screen mode The numbers shown in the figures indicate the factory default camera number display positions 4 split a 4 split b _ Each time you press the button the 1 2 5 6 J im Screen mode changes in the order of ooo 4 split a gt 4 split b gt 4 split c gt 3 4 7 EE lese D Elo 0000 4 split d gt 4 splita gt E 2 0000 4 split c 4 split d gt 9 10 13 14 4 split button i f 5 16 9 split button 10 split button 13 split button 16 split button 7 Press the 9 split button UOU0U Each time you press the button the screen mode changes in the order of 9 split a gt 9 split b 9 split a gt 7 Press the 10 split button Each time you press the button the Screen mode changes in the order of 10 split a gt 10 split b gt 10 split a gt 7 Press the 13 split button Each time you press the button the screen mode changes in the order of 13 split a gt 13 split b gt 13 split a gt 7 Press the 16 split button y lt a a e You cannot switch the screen mode while the menu screen is displayed To switch the screen mode close the menu screen first and then pre2. 16 Servicing 18 Replacement Parts Do not attempt to service this product yourself as When replacement parts are required be sure the opening or removing covers may expose you to service technician has used replacement parts dangerous voltage or other hazards Refer all specified by the manufacturer or have the same servicing to qualified service personnel characteristics as the original part Unauthorized substitutions may result in fire electric shock or 17 Damage requiring Service other hazards Unplug this product from the wall outlet and refer servicing to qualified service personnel under the 19 Safety Check following conditions Upon completion of any service or repairs to this a When the power supply cord or plug is product ask the service technician to perform damaged safety checks to determine that the product is in b If liquid has been spilled or objects have fallen safe operating conditions into the product c If the product has been exposed to rain or 20 Heat water The product should be situated away from heat d If the product does not operate normally by sources such as radiators heat registers stoves following the operating instructions Adjust or other products including amplifiers that only those controls that are covered by product heat the operating instructions as an improper adjustment of other controls may result in 21 This equipment does not provide connection damage and will often require exte
3. MITSUBISHI ELECTRIC DIGITAL RECORDER USER S MANUAL MODEL DX TL5716U THIS INSTRUCTION MANUAL IS IMPORTANT TO YOU PLEASE READ IT BEFORE USING YOUR DIGITAL RECORDER WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE AVERTISSEMENT DANGER D ELECTROCUTION NE PAS OUVRIR AVERTISSEMENT POUR ELIMINER TOUT RISQUE D ELECTRO CUTION NE PAS OUVRIR LE COUVERCLE OU LA PARTIE ARRIERE AUCUNE PIECE REPARABLE PAR L UTILISATEUR NE SE TROUVE L INT RIEUR POUR TOUTE INTERVENTION D ENTRETIEN OU DE R
4. Installation Manual This manual describes connections of devices as well as functional settings and operations to use this unit User s Guide this manual This manual is for operators of this unit and describes the operating procedures for the basic functions only 4 Symbols Tips gt Reference for operation Shows information to be referred to when you operate this recorder E gt Point to be noted Shows information to be noted when you operate this recorder 37 Reference page Shows the sections and pages to be referred to a Reference for operation Shows the operating procedures for related functions 4 Troubleshooting See Troubleshooting in the Installation Manual and take appropriate measures Contents Beginning Important Safeguards ececececececes jij Before use Contentse 0 9 0 2 Caution and Care eecccccccccccccccccc c3 Note cccceccceccccccccccccccccccccc Software License Agreement 11 Operations Adjusting the built in clock 12 Playing back recorded images 913 Changing the screen mode to display images from cameras eeeeececcccccce14 Searching for the desired image 916 Copying recorded imagese e eeeeeeeee18 Caution and care HEAVY OBJECTS SHOULD NEVER BE PLACED ON THE UNIT E G MONITOR NEVER TOUCH OR INSERT ANY OBJECT INSIDE THE UNIT Touching the inside of the cabinet or inserting foreign ob
5. Each time you click this button the display size of the search result screen changes Images recorded in the quarter picture size cannot be displayed on the full screen Each time you click this button the reverse playback speed changes in the order of approx X2 gt approx X4 gt approx X8 gt approx X16 gt Fast playback gt approx X2 Reverse frame by frame playback starts Reverse playback starts Playback reverse playback stops Playback reverse playback pauses Playback starts Frame by frame playback starts Each time you click this button the playback speed changes in the order of approx X2 gt approx X4 gt approx X8 approx X16 gt Fast playback gt approx X2 Operations 17 18 Copying recorded images You can copy the still image being displayed to a USB memory device or DVD CD disc as a still or moving image one touch copy This function is convenient to copy recording data for a short period of time 1 5 6 Set a USB memory or a DVD CD disc in the recorder The recorder automatically detects the copy destination device When both a USB memory device and DVD CD disc are detected the DVD CD disc is used as the copy destination device Display the image you want to copy in the still image playback mode and the single screen mode See 37 page 14 for the single screen mode See 37 page 13 for the still image playback mode Press the COPY button on the front panel to displ
6. PARATION SE CONFIER AUX TECH NICIENS QUALIFI S La fl che symbolisant l clair dans un triangle quilateral a pour objet de tirer l attention de l utilisateur sur le fait qu il y a des tensions dangereuses non isol es l int rieur de l enceinte du produit qui peuvent tre suffisamment importantes pour conduire au risque d lectrocution Le point d exclamation au sein d un triangle quilateral a pour objet de tirer l attention de l utilisateur sur le fait qu il y a des instructions de mise en service et d entretien de r paration dans les fiches descriptives de l appareil qui doivent obligatoirement tre respect es AVERTISSEMENT AFIN D VITER TOUT RISQUE D INCENDIE OU D LECTROCUTION NE PAS EXPOSER CET APPAREIL LA PLUIE NI L HUMIDIT ATTENTION POUR PR VENIR LES CHOCS LECTRIQUES NE PAS UTILISER CETTE FICHE POLARIS E AVEC UN PROLONGATEUR UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT SAUF SI LES LAMES PEUVENT TRE INS R ES FOND SANS EN LAISSER AUCUNE PARTIE D COUVERT L A Beginning Important safeguards PLEASE READ ALL THESE INSTRUCTIONS REGARDING YOUR RECORDER AND RETAIN FOR FUTURE REFERENCE FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE RECORDER Read Instructions All the safety and operating instructions should be read before the appliance is operated Retain Instructions The safety and operating instructions should be retained for futu
7. no event will Mitsubishi repair restore or reproduce recorded data In no event will Mitsubishi assume responsibility or liability for the following 1 Disassembly repair or alteration of this unit by the user or installer 2 Failure or breakdown in or damage to this unit resulting from misuse or careless handling by the user or installer 3 Inconvenience or damages resulting from inability to display or record images or to operate the unit s functions correctly due to any reason or cause including breakdown or failure in this unit 4 Failure in this unit due to combination with other equipment manufactured by a third party or inconvenience or damages resulting from such failure 5 Inconvenience damages or claims arising out of breakdown in this unit or loss of recorded video data due to replacement of the built in HDD by the user or installer Inconvenience or damages arising out of breakdown in this unit or inability to display or record images due to natural disaster including earthquake and storm Inconvenience damages or claims arising out of breakdown in the built in HDD or loss of recorded video data due to impact or vibration or environmental factors such as temperature at the installation site Demand for damages or claim of infringement of privacy on the ground that the video monitored or recorded by the user become public or are used for any purpose other than surveillance for whatever reason 9 Incidental spe
8. When copying to a CD RW or DVD RW disc is not done successfully clear the data and then retry With the special PC viewing communication software you can play data copied to a DVD or CD using this unit However it is not guaranteed that they can be played by all types of personal computer or DVD CD drive Mitsubishi doesn t compensate for data not recorded copied or played correctly because of a failure occurring in this unit or DVD CD disc DVD R RW discs may not be recorded or played depending on their characteristics and conditions When discs are broken data recorded on them cannot be recovered Beginning Caution and care continued Maintenance of DVD drive laser pickup Dust or dirt on the recording playback lens causes image disturbance and sound skipping making it impossible to perform recording or playback correctly Ask your Mitsubishi dealer for cleaning Don t use commercially available lens cleaning discs because they may damage the lens The DVD drive may be prone to have an error in recording or playback when its operating time for recording and playback exceeds 1000 hours CLASS 1 LASER PRODUCT Copyright This unit records data digitally Therefore exercise caution in recording video images protected by copyright Recording time and product warranty Estimated recording time displayed on the menu screen is a continuous recordable time calculated in terms of the functional operation not a pr
9. an the product regularly to prevent the ventilation openings from being covered by dust Precautions for rack mounting When mounting this unit in a rack ensure that the temperature inside the rack doesn t rise to 40 C or higher When installing a rack you are recommended to install fans to keep the temperature inside the rack 30 C or lower Don t install a device that becomes hot under this unit Otherwise the inside temperature may rise causing a failure Don t give a shock to all HDD devices in the rack Before taking this unit in or out of the rack be sure to turn off HDD devices being energized in the rack Don t place this unit near a device that generates vibrations Beginning Caution and care continued Changing installation location When moving this unit be sure to turn off the MAIN switch make sure that the unit is completely stopped and then unplug the power cord When this unit is exposed to excessive shock while being energized the internal electronic parts or HDD may be damaged Be careful especially while the power indicator or access indicator is blinking Don t move this unit for at least one minute after you turn off the power Even after the power is turned off the disc in the HDD keeps rotating by inertia for a while and the head is in an unstable state This unit in such state is more vulnerable to vibrations and shocks than while being energized Be careful not to give this unit even a slight shock for
10. are also excluded from Licensed Software and not covered by the following Software License Agreement For the terms and conditions for use of these software programs please see Notice about Apache software and Notice about OpenSSL soft DES ware Other open source software contained in this product is excluded from Licensed Software and not covered by the following Software License Agreement For the terms and conditions for use of these software programs please see Notice about other open source software The documents of Notice about software to which GNU GPL LGPL is applied Notice about Apache software Notice about OpenSSL software and Notice about other open source software are contained in the format of electronic files as notice GPL LGPL ja pdf notice Apache ja pdf notice OpenSSL ja pdf and notice other ja pdf in the OpenSoft License folder in the CD supplied with this Product MPEG 4 patent This Product is licensed under the MPEG 4 pool license only for the purpose of personal and non commercial use involving the following activities 1 Encoding video in compliance with the MPEG 4 visual standard MPEG 4 Video 2 Decoding MPEG 4 Video that was encoded by a consumer engaged in a personal and non commercial activity and or was obtained from a video provider licensed by MPEG LA to provide MPEG 4 Video For more information visit http www mpegla com 3 Playback of video recorded
11. at least one minute after turning off the power Wait at least one minute for the disc to stop and then you can move the product When moving this unit cover it with shock absorbers to prevent shocks to the inside When placing this unit on a floor lay it gently on a soft mat or cloth Maintenance Gently wipe dirt off the cabinet with a soft cloth When dirt persists clean it off using a cloth soaked in water diluted neutral detergent and wrung well and then wipe dry When using a chemical cleaning cloth follow its instructions Don t use solvent such as benzene and thinner Otherwise the surface of the product may deteriorate or the coating may come off Notes for constructing a surveillance system using this unit This unit can be controlled by external devices via the external connector RS 232C connector or LAN connector In addition external devices can be controlled via the external connector RS422 485 connector or RS 232C connector These functions allow this unit to flexibly support an advanced security system However depending on the settings of this unit or connection or combination with external devices this unit or externally connected devices may operate wrongly causing adverse effects on the entire surveillance system When constructing a surveillance system using this unit you are recommended to check its operation by connecting or combining it with other devices in advance Don t use the alarm function of this un
12. ay lt Copy menu gt Select the image to be copied from Moving image or Still image Moving image Copies data for the specified recording duration starting from the image being displayed Still image Copies 1 GOP including the still image being displayed When Moving image is selected in step 4 click the time next to Duration until the desired copy duration appears Click Execute copy You can start copying also by pressing the COPY button on the front panel After the completion of copying check that the COPY indicator goes out before you remove the DVD CD or USB memory ES You cannot perform one touch copy during copying Cfips D When the copy destination DVD CD disc or USB memory device becomes full during copying the copying is stopped D NN One touch copy Camera 1ch Copied data O Moving image Still image Start 07 07 2009 13 25 08 Duration 5Min Execute copy Copy starts also by pressing COPY Other copy Archive Setting 2 y M se LM M Displaying Copy menu using the mouse 7 Right click the mouse The mouse operation screen is displayed 2 Click the caz button to
13. by the recorder using a personal computer in which the PC viewing communication software or the OCX software for Web browser is installed or playback of video recorded by the recorder using a Web browser Software License Agreement This Software License Agreement Agreement is an agreement between you User and Mitsubishi Electric Corporation Licensor with regard to the license to use Licensed Software Article 1 Grant of license Licensor hereby grants to User a nonexclusive nontransferable license to use Licensed Software Article 2 License 1 The license to use Licensed Software granted hereunder shall mean the User s right to use Licensed Software sole ly on this Product User is hereby allowed to refer to the descriptions and instructions related to Licensed Software contained in the user s guide of this Product to the extent necessary for use of such Licensed Software 2 User shall not reproduce copy or modify in whole or in part or make addition or alteration to Licensed Software and pertinent documents 3 User shall use Licensed Software in accordance with the operating instructions described in the user s guide Article 3 License conditions 1 User shall not transfer to any third party the license stipulated in the preceding article 2 User shall not disassemble decompile or otherwise analyze the source code of Licensed Software Article 4 Ownership of Licensed Software All and any r
14. cial or consequential damages arising directly or indirectly related to this unit 10 Failure caused by any program created based on the command data provided by Mitsubishi or inconvenience damages or losses resulting from such failure This unit is intended for recording and playback of video monitored by cameras Mitsubishi doesn t assure that this unit is capable of preventing crimes Beginning 10 Note Open source software Thank you for purchasing Mitsubishi digital recorder DX TL5716U hereinafter referred to as Product Before using this Product please be sure to read the following Software License Agreement with regard to the software contained in this Product hereinafter referred to as Licensed Software By using this Product you are agreeing to be bound by the terms and conditions of the following Software License Agreement This Product contains software programs that are covered by GNU General Public License or GNU Lesser General Public License Such software programs are excluded from Licensed Software and not covered by the following Software License Agreement For the terms and conditions for use of the software programs covered by GNU General Public License or GNU Lesser General Public License please see Notice about software to which GNU GPL LGPL is applied In addition this Product contains Apache and OpenSSL including Original SSLeay library These software programs
15. ely and may claim against User for resulting damages it suffers 1 User s violation of any provision of this Agreement 2 Occurrence of filing against User for seizure provisional seizure provisional injunction or other forcible execu tion Article 9 Disposal of Licensed Software If this Agreement is terminated pursuant to the preceding article User shall dispose of Licensed Software pertinent documents and any copies thereof in its possession within two weeks after termination hereof and shall provide Li censor with a written certification of such disposal Article 10 Update of Licensed Software If User updates Licensed Software using an update CD supplied or sold by Licensor or any other means this Agree ment shall remain applicable to the updated version of such Licensed Software unless Licensor provides additional separate terms and conditions for using the updated version of such Licensed Software Article 11 Miscellaneous 1 If any provision of this Agreement is determined to be invalid by law the remaining provisions hereof shall remain valid and enforceable 2 If any doubt arises in relation to matters not defined herein or interpretation hereof Licensor and User shall discuss such doubt and attain a solution in a faithful manner Beginning 11 Adjusting the built in clock 1 Left click the mouse to display lt Main menu gt You can display lt Main menu gt also by pressing the SET UP button on t
16. er under Camera filter 5 6 until the desired number appears 4 Dy dace ead RE TZ EX ee E Click on each of date month year hour minute and second until the desired value appears 5 Click Search The image recorded on the specified date and time is displayed on the quarter screen Playback pause In addition to the time and date search you can search for images using the following methods For the detailed operating procedures see the Installation Manual For searching data in the HDD Preliminary you can use time date search only 01 12 2009 Mon Play device HDD Emergency Start 01 01 2009 09 24 31 lll Start point search This function searches for the End 11 11 2009 024008 ll Alarm list search oldest recorded data Ere seem This function searches for images using the list of times and dates when alarm recording and emergency recording started Alarm list search ll MD search This function searches for images from E End point search This function searches for the latest recording data ff NN a _ M Displaying Search menu using the mouse 7 Right click the mouse The mouse operation screen is displayed Search menu is displayed gray and dates without recording data are displayed in black 3 Click the date to be searched 2 Click the CA button to expand the menu 3 Click the Search button 49 Specifyi
17. expand the menu 3 Click the Copy button 5 Copy menu is displayed In addition to one touch copy you can copy images using the following methods For the detailed operating procedures see the Installation Manual Bl Copying data by specifying the copy range This function copies data based on the specified start and end times and data size There are 3 methods for specifying the copy conditions as follows Specifying the start time and data size Specifying the end time and data size Specifying the start and end times Backup This function makes backup of data Copying images registered in the alarm list This function copies images registered in the alarm list Operations 19 872C495A2 PRINTED IN MALAYSIA
18. he front panel 2 Select Setup to display the lt Setup gt screen IN N Setup 3 Select Setting next to Clock and language setting to display the lt Clock and language gt screen 4 Click on each of month day year hour minute and second until the desired value Clock setting SNTP is active appears 4 E 5 EEN time zone 6 5 Click Set Day light saving setting 8 B cite ee ESTE ee Select Setting next to Present time zone st lt Zone setting of time gt screen appears 7 setthe time zone depending on the location of 2 lt the recorder and then select Set After finishing the setting select Return to return to the screen of step 4 Set the day light saving setting Auto Automatically adjusts the clock according to the settings For the detailed settings select Set and then use the In area to set the time and date for advancing the clock and Out area for putting back the clock Off Auto day light saving function is not used Close the menus Playing back recorded images 1 Press the PLAY button on the front panel 2 You can play back images even during recording Se ee 2 Press the PAUSE button to pause playback e eJ Still image playback me DX Pob Run EN 3 PPE PAPER EEE PES EE EA EE E E AEE E E E E B 2 E CEE 1 Press the STOP button to stop playback Noticed W
19. heat 2 A solid vibration free surface 3 Free from high humidity excessive dust and away from magnetic fields 4 Please ensure that the ventilation fan located on the unit s back panel is not blocked UNSUITABLE LOCATIONS Placing the unit in the following places might shorten the product life Extremely cold places such as refrigerated warehouses and ice houses Places where excessive hydrogen sulfide is likely to be generated such as hot springs areas Places or locations with salt air environment NO OBJECTS FILLED WITH LIQUIDS SUCH AS VASES SHALL BE PLACED ON THE APPARATUS DO NOT PLACE HEAVY OBJECT ON THIS UNIT DO NOT STEP ONTO THIS UNIT DO NOT PLACE ANY OBJECTS IN FRONT OF THE DISC LOADING SLOT The unit may drop or fall by losing its balance It may cause injury or failure of the unit WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE THIS APPARATUS MUST BE GROUNDED Beginning Caution and care continued WARNING The supplied power cord is used for 120 V only Never connect to any outlet or power supply having a different voltage or frequency About the hard disk drive HDD This unit is equipped with HDD which is a very delicate device Therefore handle this unit carefully Don t expose this unit to vibrations and shocks It may be damaged when exposed to vibrations and shocks especially during power on or access to the HDD Don t unplug the power cord d
20. hen you change the multiplexer playback direction or playback speed during playback a black screen may be displayed When you change the multiplexer or the playback related settings during playback or when you play back data where recording status was changed due to change of recording operation a black screen may be displayed or image dropout may occur This recorder uses the motion picture compression format Due to this the recorder may take time to display the playback picture Crips D After the power is turned on playback starts from the oldest recorded data Otherwise playback starts from the point where it was stopped last time e When the PAUSE JUMP TO END button is pressed while the playback is stopped images around the end of the latest recorded data are played back in the still image playback mode Toresume playback during still image playback press the PAUSE or PLAY button When you press the camera number button during still image playback in the single screen mode the image from the camera corresponding to the button you pressed is displayed Convenient function M Selecting the device or audio to be played back 7 Press the SET UP button on the front panel or left click the mouse to display lt Main menu gt Change the playback device while playback is stopped 2 Select Device selection to display the lt Change audio and play device gt screen 3 Under Play device selection select the b
21. his unit is placed directly on the waxed floor the adhesion may increase between the floor and the non slip rubber pads on the bottom of the product causing the floor coating to come off or be colored The HDD and cooling fans are motor driven parts To ensure stable recording it is recommended to replace them every 30 000 hours of use as a guide assuming that the ambient operating temperature is 25 C When replacing HDD also replace the vibration proof rubbers at the screwed areas Note that this period is just for a guide of replacement interval and isn t intended to guarantee the lifetime of the parts They may be broken earlier because of shocks applied to the product and ambient operating temperature Be sure to use this unit within the allowable ambient temperature range 5 to 40 C and humidity range 80 or less When you use the unit out of this temperature range the internal parts may be adversely affected or a malfunction may occur In addition when the temperature rises high the characteristics of the HDD may deteriorate or its lifetime may be shortened When you use the unit in a low temperature environment supply it with power for at least 10 minutes before use Don t put your hand into the tray ejection opening Your hand may be caught in by the tray causing injury If your hand should be caught in don t try to pull it out forcefully Turn the power off first unplug the power cord and contact your Mitsubishi dealer Cle
22. ights including copyrights related to Licensed Software and pertinent documents shall be owned by Licensor or the original right holder who granted to Licensor the right to sublicense Licensed Software hereinafter referred to as Original Right Holder User shall not own any rights other than the license granted hereunder with regard to Licensed Software and pertinent documents Article 5 Disclaimer Licensor and Original Right Holder shall make no warranties whatsoever with regard to Licensed Software and have no liability for any damages suffered by User or any third party arising out of User s execution of the license granted hereunder except in cases where any applicable laws are extended Article 6 Responsibility toward third party Any issues related to intellectual property rights including but not limited to rights of privacy copyright and patent involving any third party arising out of User s use of Licensed Software shall be settled by User on its own responsi bility and Licensor shall have no responsibilities for such issues Article 7 Confidentiality User shall keep secret the details of Licensed Software and pertinent documents provided hereunder and the con tents of this Agreement that are unknown publicly and shall not disclose or leak such details and contents to any third party without consent of Licensor Article 8 Termination In case of either of the following events Licensor may terminate this Agreement immediat
23. isc wipe the moisture off the disc surface before use Dirt on the disc surface such as fingerprints and dust may deteriorate the picture and audio quality Gently wipe it off from the center toward the edge of the DVD CD disc using a soft cloth Don t use solvent such as benzene and thinner record cleaner and anti static agents Otherwise the disc is damaged When dirt persists clean it off using a cloth soaked in water diluted neutral detergent and wrung well and then wipe dry Don t use the following discs Those discs may break or a failure may occur in the unit Recording or playback may not be performed correctly Discs on which paper slips or stickers are placed or scratched discs Discs from which labels are peeled off or on which excessive adhesive is present Cracked discs deformed discs or discs repaired with adhesive After using discs store them in their cases Don t store discs in the following places Place where they are exposed to direct sunlight Place where there is much dust Place where the temperature and humidity are high You cannot play DVD video discs that are commercially available or recorded with home DVD recorders Only data recorded on this unit can be played back Don t use discs used by a personal computer or other recorder or those used for unsuccessful copying or interrupted copying due to a power failure because they may cause malfunction Data recorded halfway may not be played back
24. it for the purpose of making serious decisions or for applications involving human lives When this unit becomes unable to recognize an external device in recording because of a power failure voltage drop or other failure the recording point may move to the HDD inside this unit or other HDD To prevent such symptom it is recommended to use an uninterrupted power supply or other similar device When you unplug the power cord or turn off the breaker during recording the HDD may be broken or recorded data may become unable to be played back When you turn on and off the breaker every day program the timer recording to be performed while the breaker is on and don t turn off the breaker during the recording When the user or any third party uses external devices wrongly or external devices are affected by electric noise or they are damaged or repaired the saved data may be lost Mitsubishi doesn t take any responsibility for damages related to such data loss By connecting external HDDs to this unit you can expand the memory or use them as a copy device However when you perform recording playback or copy at a high rate using this unit recording or playback data dropout or other failure may occur depending on the connected device because of slow data transfer or slow response Be sure to check for such failure before starting the practical operation of the unit Don t use the function to control the powers of external devices using the bus powe
25. jects of any kind through the disc loading slot or ventilation holes not only creates a safety hazard but can also cause extensive damage PROTECT THE POWER CORD Damage to the power cord may cause fire or shock hazard If the power cord is damaged turn OFF the MAIN switch and carefully unplug the cord by holding the main plug If this unit is moved with the power on status the built in HDD may be damaged Confirm that more than one minute have passed since the power cord and the connecting cords were disconnected then move this unit Make sure to take the disc out and close the disc loading slot UNPLUG THE POWER CORD DURING A LONG ABSENCE Turn off the power and unplug the power cord during a long absence MAINTAIN GOOD VENTILATION Do not obstruct the many ventilation holes on the unit For maximum ventilation leave some space around the unit and place the unit on a hard level surface only and ensure it is not covered during use Heavy objects should never be placed on the unit WHEN NOT IN USE When not in use always eject the disc and turn OFF the MAIN switch CABINET CARE Never use petroleum based cleaners Clean with a soft cloth moistened with soap and water and wipe dry PVC cables or leads should not be left in contact with the cabinet surface for long periods INSTALLATION LOCATION For excellent performance and lasting reliability install in a location that is 1 Well ventilated out of direct sunlight and away from direct
26. ng the search time using the calendar 7 Click Time and date of Search menu la Set the search start time The lt Set the search start time gt screen is displayed 2 ors Hour SunMon Tue Wed Thu Fri Sat oTiT2laTaTs i i i 1 2 3 e 7 s o to t 2 Click on each of year and month until the desired value appears slot alolu ism 14 12 13 14 15 16 17 The calendar of the selected year and month appears Y a olala zz a 18119120121 22123 4 a 25 26 27 28 29 30 31 Minute Click Check data to check whether the selected device has vo os 10 15 20 zs 30 35 40 45 50 55 recording data or not Dates having recording data are displayed in check data Search start time 01 01 2008 10 30 00 5 4 Click the hour and minute to be searched 5 Click Execute The date and time specified in steps 2 to 4 are set as the search start time and then lt Search menu gt reappears Playing back the retrieved image using the buttons on the front panel Playback starts when the PLAY or PAUSE button is pressed Playback stops when the STOP button is pressed M Changing the playback speed or display size of the retrieved image using the mouse You can change the playback speed or display size using the buttons on the search result screen Search menu CD OOOO 2 3 4 5 6 7 8 9 o M DO A Oo
27. nsive work for used with outdoor or cable distribution by a qualified technician to restore the product systems to its normal operation e If the product has been dropped or the cabinet has been damaged f When the product exhibits a distinct change in performance this indicates a need for service NOTE This equipment has been tested and found to comply with the limits for a Class A digital de vice pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial en vironment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interfer ence to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Changes or modifications not expressly approved by the party responsible C for compliance could void the user s authority to operate the equipment y NOTE THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES 003 CET APPAREIL NUM RIQUE DE LA CLASSE A EST CONFORME LA NORME NMB 003 DU CANADA L yy Beginning Before use Contents How to use this User s Guide 4 About this User s Guide This manual of this recorder consists of the following two manuals
28. oduct warranty period In addition they are not a warranty period of the operational reliability of the parts and components used in the unit Motion detection function Motion detection function in this unit may malfunction depending on the input condition of the video signal If you connect this unit to a system that issues an alarm using the motion detection function take care to avoid such malfunction When the motion detection function malfunctions connect another sensor to the ALARM IN terminal on the rear of this unit Supplied power cord The supplied power cord is designed for this unit only Don t use this cord for other products Network It is recommended to confirm with your network administrator about the network settings in advance As this unit is operated through network you may suffer from damage as follows 1 Leakage or drain of information through this unit 2 Unauthorized operation of this unit by malicious third parties 3 Disturbance or deactivation of this unit by malicious third parties To prevent damage listed above take sufficient network security measures on your own responsibility Set a network password that cannot be easily guessed by third parties In addition change the password regularly Disclaimer Mitsubishi assumes no responsibility or makes no compensation for operation error of your surveillance system loss of recorded data or other damages or losses due to a failure in this unit In
29. orrectly Installation location and handling Before you first use this unit supply power to it for at least 48 hours to charge the built in backup battery so that the built in power compensator circuit can be activated When the battery isn t charged sufficiently the built in clock may go wrong or the unit may not able to recover in case of a power failure Don t plug this unit and high current devices such as copier and air conditioning into the same wall socket Place this unit on a level and stable surface When it is used on an unstable surface a failure may be caused Don t remove the outer covering of this unit Don t place this unit close to other devices They may interfere with each other disturbing video and audio Don t place this unit on a heat source In addition don t place this unit near a heat source because this unit has ventilation openings in its sides and bottom Otherwise the inside temperature may rise causing a failure When this unit is placed on or under the monitor a failure may be caused such as image disturbance and DVD CD disc ejection failure Don t place a strong magnetic object near this unit It may affect the images adversely and cause loss of recorded data Don t expose this unit to volatile substances such as insecticide or don t leave this unit in contact with rubber or plastic products for a long time Otherwise the surface of the product may deteriorate or the coating may come off When t
30. r of this unit External devices you want to use may not be suitable for the intended application of this unit For details you are recommended to contact your Mitsubishi dealer When connecting external devices be sure to secure the connected cables using the supplied clamp bands When the cables are disconnected or not connected firmly the system may become unstable or images may not be recorded Don t disconnect the cables while this unit is running Otherwise a failure may be caused For important recordings Be sure to perform test recording before starting the practical operation of this unit and also check regularly that the recording is performed correctly according to the settings during the practical operation Mitsubishi doesn t compensate for data not recorded or not played back correctly because of a failure occurring in this unit or connected devices during the use of this unit As a preparation for unexpected breakdown or accident you are recommended to make regular backups of important recordings Though digital signals don t deteriorate playback or recording may become impossible because of aging deterioration of discs depending on the storage conditions About DVD CD discs Don t use cracked discs deformed discs and discs repaired with adhesive It may break up and scatter around during the use causing breakdown or injury When you hold the disc don t touch the recording surface When condensation occurs on the d
31. re reference Heed Warnings All warnings on the appliance and in the operating instructions should be adhered to Follow Instructions All operating and use instructions should be followed Cleaning Unplug this product from the wall outlet before cleaning Do not use liquid or aerosol cleaners Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating and these openings must not be blocked or covered This product should never be placed near or over a radiator or heat register This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to 10 Power Sources This product should be operated only from the type of power source indicated on the marking label For products intended to operate from battery power other sources refer to the operating instructions Use a damp cloth for cleaning 11 Grounding or Polarization This product is equipped with a 3 wire grounding Attachments type plug a plug having a third grounding pin Do not use attachments not recommended by This plug will only fit into a grounding type power the product manufacturer as they may cause outlet This is a safety feature If you are unable hazards to insert the plug into the outlet contact your electrician to replace your obsolete outle
32. ss the camera number button or a split button Clips D To set the camera number to be displayed in each screen mode use Multiplexer setting in the Setup menu You can set the camera number to be displayed differently for each of output A and output B Y 4 O Convenient function M Changing the screen mode using the mouse single screen mode 7 Right click the mouse The mouse operation screen is displayed yu Right click 2 Click the single screen button to display the camera number buttons 3 Click the button of the camera you want to display M Changing the screen mode using the mouse split screen mode 7 Right click the mouse Right click The mouse operation screen is displayed P diei Ol DDR 2 Click the button of the split screen mode you want to display 2 Operations 15 16 Searching for the desired image You can search for images by specifying the recording date and time Press the SEARCH button on the front panel to display lt Search menu gt os 2 O 000000000 o o E L L 1 cGO69EBi NS H fol f C LH al Click the device name under Play device for example HDD Emergency until the desired a o device name appears 2 LEM Start 01 01 2009 09 24 31 You cannot select devices that are not set End 11 11 2009 02 50 08 3 nuin EM IU mime LI Eee e Click the camera numb
33. t Do not Water and Moisture defeat the safety purpose of the grounding type Do not use this product near water for example plug near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a 12 Power Cord Protection swimming pool and the like Power supply cords should be routed so that they are not likely to be walked on or pinched Accessories by items placed upon or against them paying Do not place the product on an unstable cart particular attention to cord at plugs convenience stand tripod bracket or table The product receptacles and the point where they exit from may fall causing serious injury Any mounting of the appliance the appliance should follow the manufacturer s instructions and should use a mounting accessory 13 Lightning recommended by the manufacturer For added protection for this product receiver during a lightning storm or when it is left An appliance and cart combination should be unattended and unused for long periods of time moved with care Quick stops excessive force unplug it from the wall outlet This will prevent and uneven surfaces may cause the appliance damage to the product due to lightning and power and cart combination to overturn line surges 14 Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock 15 Object and Liquid Entry Never spill liquid of any kind on the product nih
34. uring recording playback or power on This unit is equipped with a system that automatically resumes and continues recording in the event of a minor failure in the HDD or other components during recording However depending on the type of a failure in the HDD this unit may not able to continue recording For early detection of failures it is recommended to have this unit inspected every year In the event of a fault in the HDD replace it immediately For replacement of the HDD please contact your Mitsubishi dealer To replace the HDD it is required to stop recording Use recommended HDD only For HDD supported by this unit please contact your Mitsubishi dealer When the HDD is replaced the recorded data are deleted To ensure stable operation of this unit the firmware may be updated from time to time The recorded data may be deleted in such a case When you dispose of or transfer this unit handle the video data stored in HDD carefully and take all responsibilities related to the disposal or transfer In the event of a failure in the HDD during normal recording or mirroring this unit may not be able to resume recording after rebooted depending on the failure condition When you enable the mirroring function while the recorded data are stored in the HDD the recorded data are deleted When you delete the data the recorded images cannot be played back any more It is recommended to check regularly that the recorded data are played back c
35. utton of the device you want to play back You cannot select devices that are not set HDD Normal Plays back the data in the normal recording area HDD Alarm Plays back the data in the alarm recording area HDD Emergency Plays back the data in the emergency recording area HDD Preliminary Plays back the pre alarm or pre emergency recording data HDD Copy Plays back the data in the copy device HDD Archive Plays back the data in the archive device DVD CD Plays back the data on a DVD CD disc USB memory Plays back the data in a USB memory device When you change the playback device on the lt Change audio and play device gt screen and then start playback with that screen being displayed data in the device that was selected before the change are played Before starting playback close the screen 4 Under Audio channel selection select the button of the audio you want to output The audio setting made here is reflected to both the live display and playback Audio A1 Outputs the audio A1 Audio A2 Outputs the audio A2 Off No audio is output Operations Changing the screen mode to display images from cameras You can change the screen mode to display images on the monitor Bl Displaying images in the single screen mode 7 Press the button of the camera you want to display oo 0 0 0 o gt El
Download Pdf Manuals
Related Search