Miele GAS COMBISET CS 1011 User's Manual
Contents
1. 44 Help protect our environment 45 IMPORTANT SAFETY INSTRUCTIONS WARNING When using your gas appliance follow basic precautions including the following This gas combiset conforms to all uniform safety codes and regulations Read all instructions before installation or use to prevent injury and appliance damage Keep these operating instructions in a safe place and pass them on to any future user SAVE THESE INSTRUCTIONS Correct usage D Only use the gas combiset for residential cooking and for the purposes described in this manual Other uses are not permitted and can be dangerous D Persons who lack physical sensory or mental abilities or experience with the appliance should not use it without supervision or instruction by a responsible person Children D Children should not be left Unattended in an area where the appliance Is in use Never allow children to sit or stand on any part of the appliance Caution Do not store items of interest to children in cabinets above the appliance Children climbing on the appliance to reach these items could be injured D The appliance is hot during use and remains so for some time after being switched off Keep children away from the appliance D Keep all pots and pans out of the reach of children Danger of burning or scalding D Ensure that any packing material is disposed of safely and2. 2 Appliance front 3 Installation height 4 Power supply box with connection cable L 78 3 4 2000 mm Gas fitting 6 Rating label 30 Cut out m Make the countertop cut out for the desired number of appliances Remember to maintain a minimum safety distance from the back wall as well as from any tall unit or side wall to the left or right of the combiset See also the IMPORTANT SAFETY INSTRUCTIONS m Seal the cut surfaces with a suitable sealant to avoid swelling caused by moisture The materials used must be heat resistant Installation If during installation the seal around the frame does not sit flush with the countertop in the corners the corner radius maximum 4 mm can be carefully filed down to fit 31 Installation Installation of multiple appliances When installing more than one combiset appliance a support bar 2 must be installed between the appliances Countertop cut out Countertop cut out two appliances three appliances For the installation of two appliances For the installation of three appliances the width of the countertop cut out D is the width of the countertop cut out D is the sum of A and C the sum of A and B and C A B and C appliance width 11 5 16 15 or 22 11 16 288 mm 380 mm or 576 mm minus 5 16 8 mm to allow for the overhang lf more than three appliances are being installed you will need to add A B or C for each additional
3. steel cleaner To help prevent resoiling a conditioner for stainless steel can also be used Apply sparingly with even pressure These cleaning products are available from Miele Do not use stainless steel cleaner on or around the printing it may rub off Use only a soft sponge with some dish liquid and warm water to clean this area 17 Cleaning and care Burner The burner can be dismantled and cleaned when cool m Remove the burner parts and wash them in a solution of hot water and liquid dish soap Dry them thoroughly Make sure that the flame holes are clean and completely dry m Wipe the burner base clean with a damp cloth and then dry m Gently wipe the ignitor and ignition safety control with a slightly damp cloth and then wipe dry Make sure that no liquid gets into the appliance 18 Reassembling the burner m Place the burner head 40 onto the burner base 43 making sure that the thermocouple 49 and ignitor 42 align through the holes in the burner head The burner head must fit into place properly m Fit the burner ring m Seat the burner caps and into place m Put the grates in place Be careful not to mix up the parts Frequently asked questions N Repairs should only be carries out by an authorized technician in accordance with local and national safety regulations Unauthorized repairs could cause injury or appliance damage The burner does not i
4. Boil overs cause smoking and greasy spill overs may ignite D Do not use water on grease fires Smother any fire or flame or use a dry chemical or foam type extinguisher D Do not flamb under an exhaust hood Flames could be drawn up into the hood by the suction or the grease filters may ignite D If there is a drawer directly underneath the appliance without a wooden base in between ensure that no aerosols combustible liquids or other easily flammable materials are kept in it If cutlery inserts are to be placed in the drawer they must be made of a heat resistant material IMPORTANT SAFETY INSTRUCTIONS D Make certain that the power cords of small appliances do not come in contact with the appliance The insulation of the cable could become damaged Danger of electric shock D In the event of damage or defect turn off the appliance immediately Turn off the gas shut off valve and disconnect completely from the electrical supply Contact the Miele Technical Service Department Do not use the appliance until it has been repaired Ensure power is not supplied to the appliance while repair work is carried Out D Before discarding an old appliance disconnect it from the gas and electrical supply and cut off the power cord to prevent it from becoming a hazard SAVE THESE INSTRUCTIONS AND REVIEW THEM PERIODICALLY Guide to the combiset Wok burner 2 Burner grate 3 Control knob 4 Displa
5. Off indicator and Residual heat indicator 14 Cookware cee uh tc bbe wht oe ee ous ed deu ne we es oe eRe 15 Safety features 16 Ignition Sal COnWOl 222 6 lt 8 sir anim oeetareperererm eemecrren s 16 Dell CO Oll 444 w eyw det ated d GREG de EE O Ge ee ea ie we 16 Cleaning and care 17 Frequently asked questions 19 Technical SOVICE vk ci ose na ini ete 4b Kiet ar li e drercres 22 IMPORTANT SAFETY INSTRUCTIONS 26 Installation 1 144 Wee codec craie cree cet vues rue 29 RS ONATIO REN E SION Rd a de one 30 CUTOUT saa a i AE E E A EAA E A E A ETE A EAE A E E A A A A 31 Installation of multiple appliances 32 Attach the spring clips and support bars 35 Installing the appliance appliances OP Removing Me 210 1 OS PE ch aeesgudgbihoest beeen heehee cue bee af Sealing 444 44 38 H T RO a sn di ved nd bad Re a bbs eee waded ne 38 Electrical connection 39 Gas CONNECHION 22 2 eh LR Liane mr ces 41 Gas pressure regulator sn 142 Ese OPIN OCA OG EERE init 42 OMIM QUINOS s one Sb ome eaten ye bas pe OGG ed EE E dort ae 43 Converting to another type of gas
6. due to the sudden temperature change D Do not use containers made of plastic or aluminum They may melt at high temperatures D The burner grates supplied with the appliance must always be used Never place a pan on the burner by itself D Do not use aluminum foil to line any part of the combiset D For proper lighting and performance of the burner keep the igniter clean and dry D Do not heat empty pots or pans they may be damaged D For safety reasons the flame should be adjusted to be the same size as the bottom of the pan or smaller Do not use small pans with high flame settings as the flames can climb the sides of the pan D Ensure that the burner is always covered with a pan D Only use cooking utensils suitable for combiset use D Always position pan handles and utensils inward so they do not extend over adjacent work areas burner or the edge of the combiset D Do not store items on the appliance when not in use Items could melt or catch fire from residual heat or if the appliance Is turned on inadvertently D Never cover the appliance with a cloth A fire may result D Do not let cooking grease or other flammable materials accumulate on the appliance D Do not use a steam cleaner to clean the appliance Steam could penetrate electrical components and cause a short circuit D Spills containing salt or sugar should be removed immediately D Do not leave the combiset unattended while in use
7. Miele Operating and Installation Instructions Gas Combiset CS 1011 To prevent accidents and appliance damage read these instructions before installation or use M Nr 07 366 200 WARNING If the information in this manual is not followed exactly a fire or explosion may result causing property damage personal injury or death Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance WHAT TO DO IF YOU SMELL GAS e Do not try to light any appliance e Do not touch any electrical switch e Do not use any phone in your building e Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions If you cannot reach your gas supplier call the fire department Installation and service must be performed by a qualified installer service agency or the gas supplier In Massachusetts a licensed plumber gas fitter Note to the installer Please leave this instruction book with the consumer for the local electrical gas inspector s use Contents IMPORTANT SAFETY INSTRUCTIONS 4 Guide to the combiset 9 OR en ee ao kee ee ee 10 Before using the combiset 11 Sa a ee ee ee ee 12 PaSIOmIoOn SNS ONU Re Re end en deena eed dee ta ce he 12 Train On Onan REOUMUNG Lee dense ue enr r Od OSES 12 On
8. Protect your hands with oven mitts or potholders when using the appliance Use only dry heat resistant potholders Moist or damp potholders used on hot surfaces can result in steam burns Do not let the potholder touch the hot heating elements Do not use towels or other bulky items near the appliance D Be sure drafts do not blow flammable material toward the flames or push the flames so that they extend beyond the edges of the pan D Be aware of loose fitting or hanging garments when operating the combiset they may present a fire hazard D Do not heat unopened containers Built up pressure may cause the container to burst and result in injury N WARNING NEVER use this appliance as a space heater to heat or warm the room Doing so may result in carbon monoxide poisoning and overheating D Install the combiset in a room that has sufficient ventilation D This appliance must not be operated outdoors D Make sure all components of the gas burner is assembled correctly before using the combiset IMPORTANT SAFETY INSTRUCTIONS D Do not use pans that extend past the burner grate Using larger pans may cause the flames to spread out and damage the surrounding countertop or other countertop appliances D For safety and stability do not use pans with a bottom diameter smaller than the burner grate D Only certain types of glass ceramic or other glazed cookware are suitable for use on a combiset without breaking
9. appliance D width of the countertop cut out 32 Installation Sample calculations for a countertop cut out for three appliances A B C 2 appliance width appliance width appliance width Countertop minus 5 16 minus 5 16 cut out 8 mm 8 mm 11 280mm 115 16 288mm 11 280 mm 33 3 8 848 mm 11 280 mm 15 380 mm 14 5 8 372mm 40 5 8 1032 mm 11 280 mm 22 11 16 576 mm 22 3 8 568 mm 56 1 16 1424 mm 14 5 8 372 mm 11 5 16 288 mm 11 280 mm 37 940 mm 14 5 8 872 mm 15 380 mm 14 5 8 372 mm AVAL NAE 24 mm 14 5 8 372 mm 22 11 16 576 mm 22 3 8 568 mm Se Willis 1516 Min 22 3 8 568 mm 11 5 16 288 mm 11 280 mm 44 3 4 1136 mm 22 3 8 568 mm 15 380 mm 14 5 8 372 mm 511 S200 niin 22 3 8 568 mm 22 3 8 568 mm ANAL S A T36 mm 33 Installation g 22 3 8 5 8 JET nm 1 17256 H 4 16 ul 221 m 46 15 ee mm 11 ge 80 570 Spring clips 2 Support bars 3 Space between support bar and countertop Sealing strip The illustration represents the attachment of spring clips and support bars for 3 appliances An additional support bar is required for each additional appliance The position for attachment of an additional support bar depends on the width of appliance B 34 Installatio
10. ce appliances to the main power supply see Electrical connection m Turn the appliance appliances on and check the function The appliance may be lifted out using a special tool The appliance can also be pushed up and out from underneath Note push the rear out first Removing the appliance If the appliance is accessible from below it can be pushed up and out of the cut out Push up from the back first If the appliance is not accessible from below grip the appliance with both hands at the back pull forward then lift it up and out 3 Installation Sealing Tiled surfaces The appliance must not be permanently The grouting and shaded area under sealed into the countertop when the appliance frame must be flat and installed The sealing strip under the even so that the frame will lie evenly edge of the appliance provides a and the sealing strip under the edge of sufficient seal for the countertop the upper part of the appliance can provide an adequate seal against the If the appliance is sealed into countertop position the countertop or appliance could be damaged if it needs to be removed for maintenance or service 38 This appliance must be grounded according to local or national codes All electrical work should be performed by a qualified electrician in accordance with local codes and with the National Electrical Code ANSI NFPA No 70 for the USA or Canadian Electr
11. dhere rating label sticker supplied with the appliance below 22 Technical Service MieleCare USA only MieleCare our Extended Service Contract program gives you the assurance of knowing that your appliance investment is covered by 5 years of worry free ownership MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts Only genuine Miele parts installed by factory trained professionals can guarantee the safety reliability and longevity of your Miele appliance Please note that unless expressly approved in writing by the Miele service department Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele Our goal is to prevent unauthorized and untrained service personnel from working on your Miele products possibly doing further damage to them you and or your home To learn more about MieleCare Extended Service Contracts please contact your appliance dealer or visit US Online at http miele com mielecare 23 24 Installation Instructions IMPORTANT SAVE FOR THE LOCAL ELECTRICAL INSPECTOR S USE To prevent accidents and appliance damage read these instructions before installation or use IMPORTANT SAFETY INSTRUCTIONS Installation The minimum distances given in these Installation instructions are to combustible surfaces and must be observed to ens
12. e disposed of safely and Kept out of the reach of children Danger of suffocation Help protect our environment Disposal of an old appliance Old appliances contain materials that can be recycled Please contact your local recycling authority about the possibility of recycling these materials Before discarding an old appliance disconnect it from the electrical supply and cut off the power cord to prevent it from becoming a hazard 45 46 47 Please have the model and serial number of your appliance available before contacting Technical Service U S A Miele Inc National Headquarters 9 Independence Way Princeton NJ 08540 Phone 800 843 7231 609 419 9898 Fax 609 419 4298 www miele com Technical Service amp Support Nationwide Phone 800 999 1360 Fax 888 586 8056 TechnicalService mieleusa com Alteration rights reserved 2409 For the most updated manual see the Miele web site Canada Miele Limited Headquarters and Showroom 161 Four Valley Drive Vaughan ON L4K 4V8 Phone 800 643 5381 905 660 9936 Fax 905 532 2290 www miele ca professional miele ca commercial enquiries MieleCare National Service Phone 800 565 6435 905 532 2272 Fax 905 532 2292 customercare miele ca general and technical enquries M Nr 07 366 200 02
13. een the countertop cut out and the rear wall because of the high temperatures radiated The minimum distance required from the countertop cut out to the side wall 1 2 50 mm for CS 1112 CS 1122 CS 1212 Co 1221 CS 1223 CS 1326 CS 1411 6 150 mm lor CS 1912 CS 1822 CS 1421 10 250 mm for CS 1011 CS1012 CS 1028 not allowed 28 Installation Safety distance from the wall covering If a wall covering is installed a minimum safety distance must be maintained between the countertop cut out and the covering since high temperatures can damage these materials If the covering is made of a combustible material such as wood the distance between the countertop cut out and the wall covering must be a minimum of 2 50 mm For coverings made of non combustible materials such as metal marble granite or ceramic tiles the minimum safety distance between the countertop cut out and the wall covering must be 2 50 mm minus the thickness of the covering For example thickness of wall covering 9 16 15 mm 2 50 mm 9 16 15 mm minimum safety distance 1 3 8 35 mm 1 Wall frame 2 Wall covering x thickness of the wall covering 3 Countertop 4 Countertop cut out Minimum safety distance with flammable materials 2 50 mm with non flammable materials 2 50 mm minus x 29 Installation Installation dimensions lt 36 lt R4 mm Spring clips
14. es or in the absence of local codes with the National Fuel Gas Code ANSI Z 223 1 NFPA 54 for the USA or the current Can CGA B 149 1 and 2 Installation Codes for gas burning appliances for Canada Make sure that the maximum gas supply pressure before the gas pressure regulator is never more than 72 psi for both natural gas or LP gas The minimum supply pressure to get the required gas input is 4 w c for natural gas 10 w c for LP gas 41 Gas connection Gas pressure regulator pressure regulator that is convertible from natural to LP gas Propane or vice versa is included with the appliance The included regulator corresponds with the gas type of the combiset Verify before installing The adjusted pressure is natural gas 4 w c LP gas 10 w c 14 Combiset 2 Yo NPT 3 Regulator As shown in the above diagram the included regulator must be used when connecting the Miele combiset to your gas supply This item has been customized by Miele to meet all applicable safety requirements Make sure the regulator is easily accessible for adjustment after the appliance has been installed 42 For convenience an AGA or CGA approved flexible stainless steel gas hose accordion type may be used between the gas connection and the regulator This will allow the appliance to be lifted out of the countertop for cleaning or servicing Make sure that any drawers cabinet doors etc do
15. g any pressure testing of the system performed in excess of 2 psi 3 5 kPa This appliance must be isolated at test pressures equal to or less than psi 3 5 kPa Any pipe connections must be made using a thread sealant approved for gas connections Failure to correctly install these items could lead to a gas leak and subsequent explosion Keep this instruction book in a safe place for reference and pass it on to any future user IMPORTANT SAFETY INSTRUCTIONS Safety distances above the appliance The minimum safety distance given by the hood manufacturer must be maintained between the combiset and the hood above it See the installation instructions of the hood for these safety measurements If the hood manufacturers instructions are not available or if flammable objects are installed over the combiset e g cabinets utensil rail etc a minimum safety distance of 30 760 mm must be maintained If there is more than one appliance beneath a hood e g wok burner and electric combiset and they have different minimum safety distances always observe the greater distance 2m IMPORTANT SAFETY INSTRUCTIONS Safety distances to the sides of the appliance The appliance should only be installed as shown in the illustrations while maintaining the required safety distances shown Do not install the appliance between two tall cabinets this is a fire hazard A distance of at least 2 50 mm must be kept betw
16. gnite when the combiset is being used for the first time or after an extended period of not being used Possible fault Solution There could be air in the gas pipe You may need to make several attempts before the burner ignites successfully The On Off and residual heat indicators are flashing Possible fault Solution There has been a power failure Turn all the controls clockwise to e You can now operate the appliance as normal The On Off indicator is flashing Possible fault Solution The gas supply has been cut off Turn all the controls clockwise to position e You can now operate the appliance as normal Ifthe problem persists disconnect the appliance from the electrical supply for a few seconds Frequently asked questions problem persists check if The burner does not ignite after several attempts Possible fault Solution Disconnect the appliance from the electrical supply for a few seconds If the The burner is assembled incorrectly The gas valve is closed The burner is wet and soiled The flame slits are dry and unblocked The flame goes out after being lit Possible fault Reassemble the burner as shown in Cleaning and Care Burners Open the gas valve Clean the burners See Cleaning and Care Dry the igniters Solution The burner is assembled incorrectly here is
17. he strength of the flame Description of the settings 0 12 combiset is turned off Highest flame Outer and inner burners are both at the highest settings High flame Outer burner is on the lowest setting Inner burner is on the highest setting Low flame Outer burner is off Inner burner is on the highest setting Lowest flame Inner burner is on the lowest setting The knob must only be turned left to turn the appliance on and right to turn it off If the knob is turned on without pressing it down first turned clockwise to turn on used to turn the outside ring on or off without pressing the knob down or turned counterclockwise to turn the combiset off parts of the combiset might get damaged Turning on N J ISS a m Jo turn on the burner press the control knob down to pass the resistance then release the pressure and turn it counterclockwise to the largest flame symbol The ignitor will click and ignite the gas If the burner does not ignite or the flame goes out turn the control knob to e Try again after a few seconds If the burner still won t ignite after the second attempt turn the control knob to e and see Frequently asked questions m Adjust the knob to the desired setting Use Regulating the burners The inner and outer burners are both controlled by one control knob There is a stop at the 6 o clock position that requires you to
18. iance is equipped with an If a zone has been on for an unusually Ignition Safety Control This control cuts long period of time approx 4 hours it the gas supply if the flame goes out will automatically shut off and reignition is unsuccessful m To reignite the burner turn the m o reignite the burner turn the control knob to e then switch the control Knob to then switch the burner on as usual burner on as usual 16 Never use a steam cleaner to clean this combiset Pressurized steam could cause permanent damage to the surface and to components Do not use any sharp or pointed objects which could damage the seal between the frame and the countertop Never use scouring agents pads abrasive cleaning agents or strong cleaners e g oven sprays stain or rust removers these could damage the surface of the appliance Keep the ignitor in the burner dry If it gets wet it will not spark Dry your combiset thoroughly after cleaning it to prevent lime deposits Spills containing salt or sugar should be cleaned immediately Cleaning and care Combiset Let the appliance cool to a safe temperature before removing the grates m Clean the grates combiset and knobs with a sponge and a mild solution of warm water and liquid dish soap m Soak baked or hardened spills Dry the combiset and grates thoroughly after cleaning The stainless steel surfaces can be cleaned using a non abrasive stainless
19. ical Code Part for Canada CSA Standard C 22 1 WARNING Disconnect the appliance from the main power supply before installation or service To reduce the risk of electric shock make sure that the appliance is properly grounded after installation Power supply The automatic ignition requires that the combiset be connected to a 120 VAC 60 Hz power supply The supply line should be protected by a 15 A fuse Actual power consumption during ignition only is 25 W This appliance is equipped with a 78 3 4 2000 mm long power cord that is ready for connection to the appropriate outlet Place the power outlet so that it is accessible after the appliance has been installed in the countertop Electrical connection This appliance is equipped with a three prong grounding plug to prevent shock hazards It should be plugged directly into a properly grounded outlet Do not cut or remove the grounding prong from the plug If the plug does not fit the outlet have the proper outlet installed by a licensed electrician To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding system It is imperative that this basic safety requirement be met If there is any doubt have the electrical system of the house checked by a qualified electrician Note to the installer Please leave these instructions with the consumer or the appliance 39 Electrica
20. kept out of the reach of children Danger of suffocation IMPORTANT SAFETY INSTRUCTIONS Technical safety D Installation repair and maintenance work should be performed by a Miele authorized service technician Work by unqualified persons could be dangerous and may void the warranty D Before installing the combiset check for externally visible damage Do not operate a damaged appliance A damaged gas combiset is a hazard D Before installation make sure that the voltage and frequency listed on the rating label correspond with the household electrical supply This data must correspond to prevent injury and appliance damage Consult a qualified electrician if in doubt D Be certain your appliance is properly installed and grounded by a qualified technician D To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding system It is imperative that this basic safety requirement be met If there is any doubt have the electrical system of the house checked by a qualified electrician D Install the appliance so that the power cord and gas piping do not come into contact with any portion of the combiset which may become hot during use D Do not use an extension cord to connect this appliance to electricity Extension cords do not guarantee the required safety of the appliance D Do not operate the appliance until it has been properly installed in the co
21. l connection Wiring Diagram electrode ignition I electrode conductivit TT flame monitoring 1 2 GND electrode allumage indicator lamp in operation voyant fonctionnement indicator lamp residual heat voyant chaleur residuelle electronic unit electronique switch ignition interrupteur allumage transformer ignition transformateur mains terminal strip bonier cable d alimentation interf suppression capacito antiparasite condensateur Mat Nr 08536190 40 Installation and service must be performed by a qualified installer service agency or the gas supplier In Massachusetts a licensed plumber gas fitter is required This appliance must be installed with its own shut off valve and the included gas pressure regulator Both the valve and the regulator must be easily accessible to the consumer to turn on or shut off the gas supply after the appliance is installed This appliance and its individual shut off valve must be disconnected from the gas supply during any pressure testing performed in excess of psi 3 5 kPa or isolated from the gas line by closing its individual manual shut off valve at test pressures equal to or less than Yo psi 3 5 kPa Any pipe connections must be made using a thread sealant approved for gas connections Failure to correctly install these items could lead to a gas leak and subsequent explosion Gas connection The gas connection must be made in accordance with local cod
22. n Attach the spring clips and support bars Wood or solid surface countertops m Place the supplied spring clips and the support bars 2 at the marked positions as shown above by laying them on the upper edge of the cut out and then securing them with the 1 8 x 1 3 5 x 25 mm screws Supplied 35 Installation Granite countertop The screws are not needed for granite countertops m and the space between the support bars and the countertop with silicone supplied m Position and attach the spring clips Q and support bars with strong double sided tape 36 Installing the appliance appliances m Feed the power cord down through the cut out m Place the front edge of the appliance into the cut out m With a hand on each side of the appliance press down evenly on the edges until it clicks into position When doing so make sure that the appliance seal sits tightly on the countertop to ensure it is sealed correctly This is important to ensure an effective seal Do not permanently seal into the countertop When installing more than one appliance a sealing strip must be inserted into the support bar m Push the installed appliance to the side until the slots in the support bar are visible m Insert the sealing strip into the slots in the support bar Installation m Place the front edge of the next appliance into the cut out m Connect the applian
23. no soiling on the ignition safety control The flames are not touching the ignition safety control Check if Reassemble the burner as shown in Cleaning and Care Burners See Cleaning and Care Possible fault The burner is assembled incorrectly The flame appears different than usual Solution Reassemble the burner as shown in Cleaning and Care Burners The flame goes out during operation Possible fault The burner is assembled incorrectly Solution Reassemble the burner as shown in Cleaning and Care Burners 20 Frequently asked questions The igniter does not spark Possible fault The circuit breaker has tripped Solution Re set the circuit breaker Contact an electrician for assistance if in doubt Food has deposited itself between the ignitor and the burner cap Food has deposited on the ignition safety control see Cleaning and care see Cleaning and care For safety reasons after a spill on the combiset you may need to wait approx 5 minutes before you are able to reignite the burner Wait 5 minutes and ignite the burner as usual 21 Technical Service In the event of a fault which you cannot easily fix yourself please contact the Miele Technical Service Department at the address on the back of this booklet When contacting Technical Service please quote the serial number and model of the appliance A
24. not rub on this gas hose Do not use any regulator unless it has been supplied by Miele Doing SO may cause a gas leak If there is any doubt concerning installation contact the Miele Technical Service Department After connecting the appliance check all fittings for gas leaks e g with soapy water When installed properly the flame will be steady and quiet It will also have a sharp blue inner core that will vary in length proportional to the burner size Flame adjustment will not be necessary Nominal ratings Maximum output Gas type BTU hr kW Natural Gas NG 17 500 oy Propane LP Minimum output 17 500 sa Gas type BTU hr kW Natural Gas NG 680 0 20 Propane LP 680 0 20 Gas connection 43 Converting to another type of gas The combiset should have been ordered for connection to either natural gas or LP gas propane lf the combiset is not configured for the proper type of gas connection please contact your Miele Dealer If the appliance is to be connected to a type of gas other than it was originally configured for both the regulator and burner must be converted A conversion kit is available as an optional accessory from the Miele Technical Service Department 44 Disposal of packing materials The cardboard box and packing materials are biodegradable and recyclable Please recycle Ensure that any plastic wrappings bags etc ar
25. press the knob down while turning it in order to get from the high flame zone to the low flame zone m To reduce the flames from a high to low setting turn the control knob counterclockwise until resistance is felt Press the knob down to pass the stop then release the pressure and set the combiset to the desired setting m To increase the flames from a low to high setting turn the control knob clockwise until resistance Is felt Press the knob down to pass the stop then let go Now set the combiset to the desired setting ES Since the outer portion of the flame is much hotter than the center the flame should be set so that its tips do not Spread beyond the sides of the pan Flames which extend beyond the sides of the pan are hazardous Turning off m urn the knob clockwise to e This stops the gas flow and turns off the combiset 13 Use On Off indicator and Residual heat indicator When the combiset is turned on the On Off indicator lights up Once a pre set temperature has been reached the residual heat indicator will also light up The On Off indicator goes out when the combiset is turned off The residual heat indicator will remain on until the combiset is cool enough to touch Do not touch or place any heat sensitive objects on the combiset while the residual heat indicator is on Danger of damage or injury lf the display is flashing a fa
26. ult has occurred See Frequently asked questions 14 Pan size Set the combiset to a high flame when using a large diameter pan and low flame when using a small diameter pan Generally wide shallow pans will heat faster and cook more evenly than narrow tall ones Using oversized pans may cause the flames to spread out and damage the surrounding countertop or other countertop appliances Do not use small pans with high flame settings the flame can climb the sides of the pan Pots with a smaller diameter than the burner grates and pots that do not sit securely without wobbling are hazardous and should not be used The burner grates supplied with the appliance must always be used Never place a pan on the burner by itself Cookware Suitable pans Unlike pans used on an electric combiset the bases do not need to be even for good results Thick pan bases will give more even results as hot spots are reduced due to better heat distribution Thin pan bases will conduct the heat faster but not as evenly as thick pan bases Stir the food frequently to prevent burning Wok ring You can use a wok on these burners without any additional rings trivets etc If you wish to use the wok ring for extra Stability attach it as shown to the burner grates 15 Safety features Ignition safety control Safety cut off This appl
27. untertop D Do not operate any appliance with a damaged cord or plug or if the appliance has been damaged in any manner Contact Miele s Technical Service Department D Defective components should be replaced by Miele original spare parts only Only with these parts can the manufacturer guarantee the safety of the appliance D Under no circumstance open the outer casing of the appliance D While the appliance is under warranty repairs should only be performed by a Miele authorized service technician Otherwise the warranty is void IMPORTANT SAFETY INSTRUCTIONS D Before servicing turn off the gas valve and disconnect the power supply by either removing the fuse unplugging the unit or manually tripping the Circuit breaker D This equipment has not been designed for maritime use or for use in mobile installations such as aircraft or recreational vehicles However under certain circumstances It may be possible for installation in these applications Please contact the nearest Miele Dealer or the Miele Technical Service Department with specific requirements D After connecting the appliance test for leaks according to the installation instructions D If there is any doubt concerning installation contact Miele s Technical Service Department Safety D The appliance is hot during use and remains so for some time after being switched off Be careful not to touch the appliance if it may still be hot D
28. ure safe operation Failure to do so increases the risk of fire The cabinetry and venting hood should be installed first to prevent damage to the combiset D Gas appliances should only be installed in a well ventilated area D The countertop must be bonded with heat resistant 212 F 100 C adhesive to prevent distortion or dissolving D This appliance has not been designed for maritime use or for use in mobile installations such as recreational vehicles or aircraft However under certain conditions it may be possible for installation in these applications Please contact the Miele Technical Service Department with specific requirements D The combiset must not be installed over a dishwasher washer dryer refrigerator or freezer Heat radiated by the combiset may damage the appliances 26 D Deep fat fryers must not be installed directly next to gas combisets Gas flames can ignite splattering oil A distance of at least 11 5 16 288 mm should be maintained between these two appliances D Install the appliance so that the power cord or gas piping does not come into contact with any portion of the combiset which may become hot during use This appliance must be installed with its own shut off valve and the included gas pressure regulator Both the valve and the regulator must be easily accessible to the consumer after the appliance is installed This appliance must be disconnected from the gas supply durin
29. y Indicators O 5 On Off indicator 6 Residual Heat indicator Guide to the combiset Burner 7 Small burner cap Large burner cap 9 Burner ring Burner 41 Ignition safety control Thermocouple 42 gnitor 43 Burner base 10 Cleaning the combiset Before using for the first time clean the appliance as follows m Remove any protective foil m Wash the removable parts of the gas burner in a mild solution of warm water and liquid dish soap m Dry and reassemble the parts in the correct order see Cleaning and care m Wipe down the stainless steel combiset with a suitable cleaner and dry thoroughly Before using the combiset Metal components have a protective coating which may give off a slight odor the first time your new appliance is heated The harmless odor will dissipate after a short time and does not indicate a faulty connection or appliance defect Use Fast Ignition System The gas combisets are equipped with a Fast Ignition System which incorporates the following features The control knob does not need to be pressed until the flame lights lf the flame goes out because of a draft for example the burner is automatically re ignited If re ignition is unsuccessful the gas supply is automatically interrupted see Ignition safety control Turning On Off and Regulating The control Knob is used to turn the burner On Off and to regulate t
Download Pdf Manuals
Related Search