Home

Miele Coffeemaker CVA 2660 User's Manual

1. Installation options The coffee system is designed to be built into cabinetry Miele appliances can be installed flush or proud Discuss your installation requirements with your architect designer and installer 57 Installation 58 Installation If the machine is installed in combination with other Miele appliances it should be installed with a protective base between the appliance and the unit 9 lo O o lo Ne 59 Installation A display cabinet is also available from Miele or your local dealer as an installation option The display cabinet is intended to hold the CVA 2660 and an optional ESS 2060 Storage Drawer or EGW 2060 Cup Warmer 60 Installation Installation Make sure power is not supplied to the appliance while installation or maintenance work is performed Disconnect the power supply to the work area by unplugging the unit tripping the circuit breaker or removing the fuse The coffee system must be properly installed before being used m Open the door and partially tighten m Plug the appliance into the electrical the screws by hand Do not use an outlet electric screwdriver m lf you have a cabinet with m Carefully turn the lower screws to 19 mm side panels you will have to center the machine drill four holes first me Center the machine in the a To fix the machine in the cabinet cabinet tighten the upper scr
2. When turned on for the first time a welcome screen along with other messages will appear in the right display The welcome screen will be displayed each time the machine is turned on until 5 drinks including steam have been prepared The displays light Turning off m Press the left jog shuttle until the displays go dark If the automatic rinsing function is activated both displays will go dark when turned off If coffee was dispensed the machine will be rinsed and Machine Rinsing will appear in the right display When finished the machine will shut off completely First steps to use Before using the coffee system 4 Rinse the lines RINSE for the first time 1 Clean the parts m Hand wash the coffee capsule plate i ia with hot water and liquid dish soap m Turn the left jog shuttle to Rinse m The water tank can be washed in the Riese MONEO SE dishwasher Water runs from the coffee dispenser gt Fill the water tank m Press the steam lever down Water runs from the steam valve m Open the appliance door m Lift the water tank and pull it out ml UST SAM oh ADS seconds m Fill the container with fresh cold tap water to the Max mark Push the water tank back into the machine 3 Fill the system with water HOT WATER m Set a cup under the steam valve m Turn the left jog shuttle to Hot water m Press the right jog shuttle The steam valve dispenses hot water m Pre
3. HOT WATER m Turn the left jog shuttle to the Hot water option m Press the right jog shuttle and half fill the cup with hot water m Press the right jog shuttle again to stop the water from dispensing m Leave the cup for a few seconds to warm then pour the water away To pre warm with steam HEATING WITH STERM m Turn the left jog shuttle to the Heating with steam option m Press the steam lever down The steam supply is temporary If the steam stops prematurely push the steam lever up then down again m Push the lever up to stop the steam from dispensing m Pour away any excess water Making coffee Espresso and coffee The flavor of the coffee depends on the coffee capsule and the quantity of water used To ensure the machine uses exactly the amount of water to suit your taste and your cup size there is a choice of four serving sizes for espresso coffee Aside from the serving size making coffee and espresso are done the same way m Place a cup under the coffee dispenser m Turn the left jog shuttle to the desired coffee type ESPRESSO m Turn the right jog shuttle to the desired coffee or espresso size Espresso W Coffee P Double espresso R Double coffee When selecting a double coffee or espresso two capsules will be dispensed one after another You can set the water amount to your taste See Setting the serving sizes m Press the right jog shuttle t
4. m To leave the menu turn the ri shuttle to the back symbol press to confirm t jog and Not saving an entry m f you do not want to save an entry turn the right jog shuttle until back is displayed Press and the entry will not be saved Making coffee Rinse the water lines before preparing the first drink of the day If the Automatic rinsing option is set to on and the machine is still cold this will take place automatically The heating system will heat and the water lines will be rinsed If the Automatic rinsing option is set to off use the option Rinse in the left display to rinse the lines See Daily coffee system care m Press the left jog shuttle to turn the machine on The left display lights The right display shows briefly This is a reminder to fill the water tank with fresh water The next message shows Heating up Please wait If the Automatic rinsing option is set to on default setting the next message shows Rinsing in progress please wait Water will run out of the coffee dispenser and a sound will be heard as the carousel aligns The right display shows ESPRESSO Making coffee Pre warming the cups Prewarming the cups allows the coffee to fully develop the flavor and aroma Use caution Steam and hot water are very hot m Place a cup under the steam hot water valve 18 To pre warm with hot water
5. The double espresso 2 and double coffee B symbols dispense two portions of espresso or coffee one after another This requires two coffee capsules and double the amount of water set for a single coffee or espresso 24 Setting a default serving size Have the correct cups handy m Place the desired cup under the coffee dispenser m Turn the left jog shuttle to the desired coffee type ESPRE m Select the drink you would like to program ESPRESSO l PROGRAM THE AMOUNT m Press and hold the right jog shuttle until Program the amount shows in the display m Release the jog shuttle m Press the right jog shuttle again when the cup is filled to the desired preference The programmed amount will now be dispensed every time the drink is selected The water flow stops automatically when it reaches the maximum amount possible espresso 2 5 oz 75 ml coffee 6 oz 175 ml The maximum water amount will then be saved for the drink selected Setting user profiles Setting the user name Up to four different user profiles can be programmed to accommodate different preferences and serving sizes See Setting serving sizes SETTINGS P m Turn the right jog shuttle to the User name symbol then press to confirm the selection USER 2 m Turn the right jog shuttle to the desired user and press to enter a user name USEF COEF GHIJELA The alphabet is displayed
6. When turning the jog shuttle to the right the rest of the alphabet and the numbers 0 through 9 are shown To enter text m Turn the right jog shuttle to the first letter or number and press to confirm The selected letter shows in the upper line m Repeat until the desired name is entered To delete text m Turn the right jog shuttle until delete appears in the display m Pressing the jog shuttle deletes the last letter entered m Turn the jog shuttle counterclockwise to the alphabet and continue entering the name Saving an entry m When the entry is complete turn the jog shuttle until OK is displayed Press to confirm The display shows the main menu The back symbol t is selected m Press the right jog shuttle to get to the main display menu Not saving an entry m Turn the right jog shuttle until back is displayed m Press the jog shuttle and the entry will not be saved 25 Setting user profiles Setting user profiles serving sizes In addition to the default different serving sizes can be programmed for four additional users PROFILE m Turn the right jog shuttle until the desired user name is selected Press to confirm The symbol will appear in the upper right hand corner of the left display to show that a user profile has been selected m Proceed as if setting a default serving size All water quantities will now apply for the selected user 26 Making
7. americano is a thin espresso with water added Caff corretto is espresso with a splash of liquor Caff freddo is iced coffee An extended version of espresso served with ice Caff latte is a double espresso in a large cup filled with hot milk topped with little or no foam Caff moca consists of equal parts of espresso hot milk and cocoa Caff ristretto is the strongest most concentrated espresso The water is reduced to 2 tablespoons 30 ml per serving Caffeine the caffeine content of espresso is only a third or half of that found in coffee The stronger the roast the less caffeine the espresso will contain Cappuccino is espresso with frothed milk It is equal parts of espresso hot milk and foam Cappuccino chiaro is a light Cappuccino with less espresso and more hot milk 64 Cappuccino scuro is a dark Cappuccino with more espresso and less hot milk Cappuccino senza schiuma is a cappuccino without the froth Crema is the sign of the perfect cup of espresso a fine nut or cinnamon brown foam on the surface of the espresso which is only created when the pressure is sufficiently high The crema contains foamed oils which are rich in flavor and aroma Espresso see Caff Espresso corto is a short strong espresso Espresso doppio is a double portion of normal espresso Espresso lungo is the longer less concentrated version served in a standard coffee cup Espresso r
8. cappuccinatore The steam supply is temporary If the steam stops and there is not enough froth prepared push the steam lever up then down again Frothing milk into a cup m Pre warm the cup before filling with froth m Push the cappuccinatore spout into the in position m Turn the valve all the way to the right for frothing m Fill the cappuccinatore no higher than the upper mark with cold milk and cover with the lid m Place the cappuccinatore under the steam valve and a cup under the spout m Slowly press the steam lever down The steam lever must click into the down position otherwise the valve is not properly connected to the cappuccinatore m Push the steam lever up when enough froth is prepared 21 Making coffee Frothing milk in the cappuccinatore m Pull the cappuccinatore spout into the out position m Turn the valve all the way to the right for frothing m Fill the cappuccinatore to the lower marking with cold milk and cover with the lid m Place the cappuccinatore under the steam valve m Slowly press the steam lever down The steam lever must click into the down position otherwise the valve is not properly connected to the cappuccinatore m Push the steam lever up when enough froth is prepared 22 Heating milk in the cappuccinatore m Fill the cappuccinatore to the upper mark with cold milk and put the lid on m Pull the capp
9. desired turn off time is set press to confirm The setting will be automatically saved and the display will go back to the previous screen The coffee system will turn off at the preset time If rinsing is set to on and the machine has been used the coffee system will automatically rinse the lines before turning off 29 Settings Turning on at a preset time A specific time can be set to turn the machine on e g for breakfast In order to use this function the clock has to be set SETTINGS fa m Turn the left jog shuttle to Settings TIMES m Turn the right jog shuttle to the clock symbol press to confirm SWITCH ON AT m Turn the right jog shuttle to Switch on at this will only be seen if the clock is correctly set m Press the jog shuttle to confirm the setting SHITCH ON AT m Turn the right jog shuttle to set the hours press to confirm m Turn the right jog shuttle to set the minutes press to confirm 30 The setting will be automatically saved and the display will go back to the previous screen The coffee system will turn on at the preset time If rinsing is set to on the coffee system will automatically rinse the lines when turned on If the coffee system automatically turns on three times and no beverage is dispensed the machine will not turn on automatically after that The preset times will remain saved and will be activated when the machine is manually
10. Please contact the Miele Technical Service Department with specific requirements P Before service or maintenance disconnect the power supply by either removing the fuse tripping the circuit breaker or unplugging the unit IMPORTANT SAFETY INSTRUCTIONS gt Installation work and repairs should only be performed by a trained technician in accordance with national and local safety regulations Repairs and other work by unauthorized persons could be dangerous gt Never open the outer casing of the appliance Tampering with electrical connections or components and mechanical parts is dangerous and may cause machine damage gt If the machine is installed in combination with other appliances it should be installed with a protective base between the appliance and the unit gt To protect against fire electric shock and injury to persons do not submerge cord or plugs in water or other liquid P Do not let cord hang over edge of table or counter or touch hot surfaces gt Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner Contact Miele gt Always attach the cord to the appliance first then plug it into the wall outlet To disconnect turn the machine off by pressing the left jog shuttle then remove plug from wall outlet Use P Use only Nespresso coffee capsules with this machine The coffee system must be maintained d
11. espresso coffee with user profile If a user profile was set select the profile first before preparing a drink PROFILE ft n m With the right jog shuttle select the user Press to confirm The user symbol will be shown in the upper right hand corner of the left display to signify that a user was selected m Place a cup under the coffee dispenser m Turn the left jog shuttle to the desired coffee type ESPRESSO m Turn the right jog shuttle to the desired coffee espresso size m Press to confirm and the drink will be dispensed Settings The coffee system can be customized to suit individual preferences Selecting a language SETTINGS P m Turn the left jog shuttle to Settings LANGUAGE DEI it The language symbol is selected in the right display m Press the right jog shuttle to select the language option LANGUAGE 5 English F gt m Turn the right jog shuttle until the desired language shows in the display A check marks the selected language Selectable languages English US and GB German French Dutch Italian Spanish Portuguese Turkish Swedish Norwegian Danish Finnish Polish Czech Hungarian Greek and Russian m Press the right jog shuttle to select the language option The setting will be automatically saved and the display will go back to the previous screen All displays will now appear in the selected language If a l
12. no type is allocated to the chamber the upper display line shows empty Some coffee types are factory set which you can either accept or change Allocating various coffee types Allocating different coffee types CHAMBER 5 _ ARPEGGIO m Turn the right jog shuttle to the desired coffee type and press to confirm it to that chamber Setting a new coffee type CHAMBERS lt BOWE OS i gt m Turn the right jog shuttle to save as if no coffee type is allocated yet to save a new coffee type or to name a coffee type yourself m Press the right jog shuttle CHAMBER 5 MB COEFGHIJELA The alphabet is displayed Turn the right jog shuttle to the right to display the rest of the alphabet and the numbers 0 through 9 16 To enter text m Turn the right jog shuttle to the first letter or number and press to confirm The selected letter shows in the upper line m Repeat until the desired name is entered To delete text m f you made a mistake turn the right jog shuttle until delete appears in the display m Pressing it deletes the last letter entered m Turn the right jog shuttle counterclockwise to the alphabet and continue entering the name Saving an entry CHAMBER 3 TEST lt E IS m When the entry is complete turn the right jog shuttle until OK is displayed m Press to confirm The main menu is displayed the last selected chamber is highlighted
13. of the cappuccinatore clogged Turn the spout to the cup See Common coffee system care Cappuccinatore Clean the cappuccinatore What if the coffee dispensing is interrupted If a double espresso coffee was selected the machine uses two coffee capsules 50 Dispensing is interrupted when the carousel chambers are empty Refill coffee capsules Frequently asked questions Coffee results What if the dispensed coffee has some ground coffee in it The capsule plate is soiled Clean the capsule plate What if the water flow stopped when p rogramming the serving size If the maximum water amount is reached the water dispensing stops automatically The maximum water amount is saved There was not enough water in the tank The dispensed water amount will not be saved Refill the water tank and reset the serving size What if the preparing time and amount of coffee is very different Depending on coffee type the grinding level will differ between coarse and fine Preparing time and amount will vary What if the espresso coffee is not hot enough Check if the capsule plate is clogged Clean the capsule plate Pre warm the cup What if water is in the waste unit This is residual water from the cleaning process Pour water away What if coffee water is in the waste unit The capsule plate is not i
14. programmed time The water temperature may be too The unit is blocked until the water has high cooled 47 Frequently asked questions What if the light turns suddenly off The light turns off automatically when the machine has not been used for 10 minutes What if the door cannot be opened or closed The steam lever is not pushed up all the way Press the lever down and then up again all the way What if the time of day needs to be reset If the machine was unplugged or a power failure occurred Reset the time of day The preset times for turning on or off automatically are saved in the memory and do not need to be reset What if despite the empty drip tray a message to empty it shows up The contacts are soiled The drip tray is not inserted correctly Clean and dry the contacts Insert the drip tray correctly Turn the machine off and on again with the main switch If the message still appears contact Technical Service What if the machine does not rinse when turned on although the automatic rinsing function is set to On If the coffee system has still a temperature of 140 F 60 C or higher the machine will not be rinsed 48 Frequently asked questions Preparing dispensing problems What if no drink is prepared although there are coffee capsules and water in the tank Take out the water tank and the
15. turned on again This is a safety measure so that the machine does not turn on daily during a longer absence Settings Turning off at a preset time A specific time can be set to turn the coffee system off In order to use this function the clock has to be set m Turn the left jog shuttle to Settings TIMES Peet oita m Turn the right jog shuttle to the clock symbol press to confirm SWITCH OFF AT m Turn the right jog shuttle to Switch off at this will only be seen if the clock is correctly set Press to confirm the setting SMITCH OFF AT m Turn the right jog shuttle to set the hours press to confirm m Turn the right jog shuttle to set the minutes press to confirm The setting will be automatically saved and the display will go back to the previous screen The coffee system will turn off at the preset time If rinsing is set to on and the machine has been used the coffee system will automatically rinse the lines before turning off Deleting the preset times m Repeat the steps to set the preset time until you are prompted to set the actual time of day m Turn the jog shuttle until only dashes are shown in the second line of the display m Press the right jog shuttle to confirm 31 Settings Setting lighting display m Turning the right jog shuttle clockwise contrast and brightness increases the bar size and brightens the settings m Press the right jog shuttle
16. Dissolve two of the enclosed descaling tablets in the water tank m Close the water tank and insert it into position Please use the waste container m Take the waste container from the interior and set it under the coffee dispenser and steam valve Please use descaling funnel and close the door m Open the door and remove the capsule plate m Insert the colored funnel into the capsule plate opening Please empty drip tray and waste container m Since the machine is also rinsed inside the drip tray needs to be emptied to continue m Also empty the waste container at this time Please fill with fresh water m Take the water tank out rinse out any descaling residue thoroughly with water m Fill with fresh water to the Max mark and reinsert the tank 45 Fault messages If an error occurs a fault message will appear in the right display Minor problems can be fixed without a service call Message Chamber empty please refill Possible fault The selected coffee chamber is empty Solution Fill with coffee capsules Please fill with fresh water This is a reminder to fill the water tank with fresh water when the machine is turned on Please set the time of day The machine was disconnected from the power supply and the time of day needs to be reset Set the time of day Empty drip tray and clean contacts The drip tray is full and or the metal contact sensors on the tr
17. Miele Operating and Installation Instructions 7 Coffee System CVA 2660 To prevent accidents en US CA and machine damage read these instructions before installation or use M Nr 07 173 890 Contents IMPORTANT SAFETY INSTRUCTIONS 5 Guide to the machine 00 0 eee 8 DiSplay iii AES Le E deed Pei 10 First steps to USE 11 Turning the machine on and Off 11 Filling water and coffee capsules 000 0 00000 13 Filling the coffee capsule carousel 0 14 Changing the coffee capsules 0 14 Allocating various coffee types 15 Making CoOmee 2i 05 3 nog ode fb Bob eee tela 17 Espresso and Cofee eo e ae an e eegen Ar aa aE 19 Interrupting the brewing ii 19 Setting serving Sizes 24 Setting a default serving size 2 eee 24 Setting user profiles 25 Setting user profiles Serving SIZES 0 2 0 0 0 eee 26 Making espresso coffee with user profile 26 Settings ee a ee 27 Selecting a languages eugecuie Siege baw ee ba ee eed See ees 27 Setting the time Of davis neds Raed derr Peay se eed eens eae ee eke bees 28 Turning off after Standby time 29 Turning on at a preset time 30 Turning off at a preset time 31 Deleting the preset UMES 4 4 c40 hte csasee a ee deena haan es 31 Setting lighting display contrast and brightness 0 000 000 eee 32 AUTOMALICAASING srt i Odd edad Ea 33 Total coffee counter INFO LL 35 Factory Selg
18. There is a slight fluctuation in the electrical supply Call Technical Service if the message appears regularly What if F 72 shows A coffee capsule has jammed above the waste unit m Open the appliance door m Remove empty and return the waste unit m Close the door m If the message still shows see Removing a jammed capsule From the carousel tray What if the message F 75 or F 76 shows in the display A coffee capsule has jammed m Open the appliance door m Remove empty and return the waste unit m f the message still shows open the appliance door and follow the prompts in the right display See Removing a jammed capsule from the capsule plate What if any other fault messages F appear in the display Call the Miele Technical Service Department 53 Removing a jammed capsule Turn the machine off at the main switch in the upper left corner Danger of electric shock The machine must be turned off before performing the next steps From the carousel tray m f the message still appears call Technical Service From the capsule plate m Take the carousel and the capsule plate out m Open the appliance door m On the right side of the capsule plate is an opening Check if a coffee capsule has jammed in there or m Insert a spoon handle underneath the further up in the unit carousel tray on the right side Move the spoon handle with care to the left si
19. aily to prevent the growth of harmful bacteria and mold Please read the Coffee system care section of this booklet Caution There is a risk of burns when dispensing hot beverages they are extremely hot P gt Do not touch hot surfaces Use jog shuttles or steam lever gt Children should not use the appliance unsupervised Danger of scalding gt This appliance must not be installed or operated outdoors gt To avoid injuries allow the coffee system to cool before cleaning or before putting on or taking off parts Turn the machine off at the main switch when not in use and before cleaning P gt Only fill the water tank with cold fresh tap water Warm or hot water or any other liquids may damage the machine The water should be changed daily to prevent bacteria or mold growth IMPORTANT SAFETY INSTRUCTIONS P The water lines must be rinsed and the machine cleaned thoroughly before the first coffee is prepared See Daily coffee system care P The use of accessories not recommended by the appliance manufacturer may result in fire electric shock or injury to persons P Do not reach into the perforator Injuries may occur gt Do not use damaged broken or dented capsules They may jam in the machine and damage it P The hot water and steam dispensed could cause scalding Use these functions carefully The machine must never be used to clean objects P gt Never use a steam cleaner to cle
20. an the appliance Pressurized steam could damage electrical components and cause a short circuit P gt The coffee system must be descaled regularly with the supplied descaling tablets In areas with very hard water the machine needs to be descaled more often The manufacturer cannot be held responsible for damages resulting from insufficient descaling P gt Only use the descaling tablets provided by Miele and be sure to use the correct mixture of water and descaler Otherwise appliance damage may occur gt The capsule plate will soil more or less depending on the coffee capsule used Clean the capsule plate as necessary with a cleaning tablet available from Miele gt Do not hang lean sit or place heavy items on the door The machine may be damaged SAVE THESE INSTRUCTIONS Guide to the machine Front view T Left display 2 Left jog shuttle Press this jog shuttle to turn the machine on and off Turning it selects a desired program option or setting 3 Right jog shuttle Press this jog shuttle to start and stop the dispensing of coffee or hot water to select an option to alter or customize a program to save a setting into memory when the machine is turned off Turning it selects a desired program option or a setting Right display Upper door handle for installation at countertop height Lower door handle for installation at a hig
21. anguage is accidentally selected follow the flag to return to the language setting Settings Setting the time of day TIME OF DAY ia do __ m Turn the right jog shuttle to select the hours press to confirm TINE OF DAN i2 DO m Turn the left jog shuttle to Settings LANGUAGE Pr e i SS tw The language symbol is highlighted in the right display TIMES m Turn the right jog shuttle to select the minutes press to confirm TINE OF DAY ae ine right jog anung to the clock The setting will be automatically saved symbol press to confirm and the display will go back to the TINE OF DAY previous screen Two symbols for preset times now be will shown m Press the right jog shuttle again TIME OF DAY lt m Turn the right jog shuttle to select the time format press to confirm Settings Turning off after Standby time To conserve energy the coffee system can be set to turn off automatically after a programmed time interval A time period between 20 minutes and 2 hours can be selected The time is measured from the last time coffee espresso was dispensed SETTINGS P m Turn the left jog shuttle to Settings TIMES PICO it m Turn the right jog shuttle to the clock symbol press to confirm SWITCH OFF AFTER m Turn the right jog shuttle to SWITCH OFF AFTER Press to confirm the setting SWITCH OFF AFTER m Turn the right jog shuttle until the
22. antee the safety reliability and longevity of your Miele appliance Please note that unless expressly approved in writing by Miele s Service department Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele Our goal is to prevent unauthorized and untrained service personnel from working on your Miele products possibly doing further damage to them you and or your home To learn more about MieleCare Extended Service Contracts please contact your appliance dealer or visit us online at http miele com mielecare 55 Electrical connection The coffee system comes equipped with a 6 ft 1 8 m power cord with a NEMA 5 15P molded plug for connection to a 120 V 15 A 60 Hz power supply Connection should be made via a suitable isolator with an on off switch which should be easily accessible for servicing work Installation repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held responsible for unauthorized work Verify that the voltage load and circuit rating information found on the data plate match that of the household electrical supply before installing the coffee system If there is any question concerning the electrical connection of this appliance to your power supply please consult a licensed electrician or call Miele s Technical Service Department 1 800 999 1360 1 800 565 6535 56 Installation
23. ay are soiled Empty and clean the drip tray Clean and dry the contacts Please use descaling funnel and close the door The capsule plate needs to be taken out and replaced by the descaling funnel Remove the capsule plate and insert the colored funnel v ease insert capsule ate ze The capsule plate or perforator are missing or the descaling funnel is still in the machine Insert the capsule plate or perforator v ease insert carousel The carousel is missing or the sensor under the carousel tray is soiled Insert the carousel and clean the sensor with a cloth Please open the valve Steam cannot be supplied if the steam valve is closed Press the steam lever down Please close the valve The steam lever is still pressed down Push the steam lever up Maintenance required The perforator needs to be replaced after about 15 000 cups of coffee Turn the left jog shuttle to Settings Turn the right jog shuttle to maintenance and change the perforator see Common coffee system care Maintenance Confirm to start The selected process is prompted to start Press the right jog shuttle Confirm to continue The descaling needs to be continued Press the right jog shuttle Empty A coffee chamber was selected which has not been allocated to a coffee type Allocate a type of coffee to the chamber No of uses until descaling has to be
24. d responsible for damage caused by improper use of the appliance Electrical safety gt Before connecting the appliance to the electrical supply make sure that the voltage and frequency details listed on the data plate correspond with the household electrical supply If in doubt consult a qualified technician gt The appliance must be properly installed before operation to ensure that no electrical components are accessible Ensure that power is not supplied to the appliance while installation work repairs or maintenance is performed gt Be certain your appliance is properly installed and grounded by a qualified technician To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding system It is imperative that this basic safety requirement be met If there is any doubt have the electrical system of the house checked by a qualified electrician The manufacturer cannot be held responsible for damages caused by the lack or inadequacy of an effective grounding system gt Do not use an extension cord to connect the appliance to electricity Extension cords do not guarantee the required safety of the appliance danger of overheating gt This appliance is not designed for maritime use or for use in mobile installations such as recreational vehicles or aircraft However under certain conditions it may be possible for installation in these applications
25. de m Turn the machine off at the main switch m Pull out the carousel and remove the coffee capsule m Throw out the capsule so it does not jam again It may be damaged or dented m Remove the coffee capsule only with a wooden spoon handle m Remove the tray by pulling it completely out then pushing it up slightly Clean the area underneath it making sure to wipe clean the sensor si Turn the machine on at the main m Reinsert the capsule plate and the carousel in the tray platform Reinsert the tray switch m Turn the machine on at the main m Close the door switch m f the message still appears contact m Close the door Technical Service 54 After sales service In the event of a fault which you cannot easily fix yourself please contact the Miele Technical Service Department at the contact information on the back of this booklet When contacting the Technical Service Department please quote the model and serial number of your appliance given on the data plate inside the appliance MieleCare USA only MieleCare our Extended Service Contract program gives you the assurance of knowing that your appliance investment is covered by 5 years of worry free ownership MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts Only genuine Miele parts installed by factory trained professionals can guar
26. done 46 The machine counts the number of drinks made before descaling has to be carried out Once this number reaches zero the machine locks until the descaling process has been successfully completed Descale the machine see Descaling the appliance Frequently asked questions Repairs to electrical appliances should only be carried out by a suitably qualified person in accordance with local and national safety regulations Repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held responsible for unauthorized work Machine Problems What if the light does not illuminate when turned on Is the unit locked If not the light bulb has burnt out Contact the Miele Service Department Is the lighting set too low Adjust the lighting What if the display messages are difficult to read The contrast or brightness of the Adjust the display contrast brightness displays are too low high What if there is no prompt in the display The unit has no power ls the main switch turned off ls the machine plugged in Check that the fuse is not defective If so contact the Miele Service Department What if the unit suddenly turns off ls the machine plugged in Plug the machine in Is the machine programmed to The machine turns off into standby switch off after a programmed mode when not used for the time
27. e chambers with the flat silver side down Take care that the capsules sit loosely in the chambers so they do not jam m Insert the carousel into the carousel tray m Push the carousel all the way into the machine m Close the door The machine aligns the carousel automatically A sound will be heard Changing the coffee capsules m Pull out the carousel tray and lift out the carousel m Push the carousel ring up and take out the capsules Allocating various coffee types Twelve different Nespresso coffee types m Take the carousel from the machine are available for this coffee system to see which coffee type is filled in They differentiate in terms of acidity each chamber fruitness bitterness and roast as Therefore the preparing times will vary TYPE ARPEGGIO See The Espresso Lungo range for le EES _ more information on the coffee types m Turn the right jog shuttle to the Allocating the coffee types desired chamber and press to confirm Five different coffee types can be filled in the five chambers of the capsule carousel The chambers can be either allocated to the desired coffee types or filled with the same coffee type in all chambers SETTINGS F m Turn the left jog shuttle to Settings ALLOCATE TYPE m Turn the right jog shuttle to the Coffee bean symbol Press to confirm The upper line shows the coffee type the lower line shows the chamber number If
28. e system should be cleaned after each Turn the machine off at the main day of use to prevent mold and switch before cleaning bacteria growth Allow the coffee system to cool Dishwasher safe before cleaning Danger of burns Watertank Do not clean the unit with a steam Drip tray with grid clean Metal drip catch Never use abrasive cleaning agents Cappuccinatore if used These will damage the machine Hand wash only with hot water and Rinse liquid dish soap If you do not wish to rinse the lines Plastic drip catch automatically they have to be flushed manually It is recommended that the machine is rinsed twice daily once before using the machine and once before turning it off for the day m Place a cup under the coffee dispenser and the steam valve RINSE m Turn the left jog shuttle to Rinse m Press the right jog shuttle Water runs from the coffee dispenser m Press the steam lever down Water runs from the steam valve m Push the steam lever up after a few seconds The lines are rinsed Drinks can either be prepared now or the machine may be turned off 37 Cleaning and care Common coffee system care Interior m Clean all interior parts and areas of the machine with a solution of hot water and liquid dish soap See below for more details Capsule carousel and tray m Pull out and remove Both pieces are dishwasher safe Capsule carousel niche m Clean the sensor i
29. e enrera ORA n RA Ana 35 System lock es i e e ed he a 36 Cleaning and care tenes 37 Daily coffee system Care 37 Common coffee system care 38 Contents Cleaning and care a 42 Descaling the appliance 0 00s 43 DESCAlIng PrOMPits cvs ve ol EL oca 45 Fault messages eee eee 46 Frequently asked questions 0 000 47 Removing a jammed capsule 00 54 After sales Service 55 Electrical connection 56 Installationi i glor eli ad e i 57 INStallvOn GOONS ee io i A a e a 57 INStAlAUON oe o awed ieee leale 61 PIOGIAMIMINO rie Lr ARIA ni 62 Setting the language 0 62 Setting the water hardness 6 eee ees 63 Coffee glossary 0 0 0 0 02 eee 64 The Espresso fange lt iii ae Ee REAR ERRE ped 65 The Lungo range iii iaia 66 Caring for the environment 67 IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances basic safety precautions should always be followed including the following Read all instructions before installation or use of the coffee system Please read these instructions carefully to prevent accidents and machine damage This appliance is for household use only Do not use appliance for other than intended use Any other use could be dangerous This appliance complies with current safety requirements Improper use of the appliance can cause personal injury and material damage The manufacturer cannot be hel
30. ews Tighten the screws just so they leave a mark in the panel Remove the machine from the cabinet and drill four holes 2 mm with a diameter of 3 46 4 5 mm m Level the machine with the four height adjustable feet The feet can be turned out up to 3 g 10 mm m Push the appliance all the way back into the cabinet 61 Installation Programming The appliance must be correctly installed and connected before the first use Setting the language m Press the left jog shuttle to turn the machine on Miele Welcome When turned on for the first time a welcome screen as well as other messages will appear in the right display The welcome screen will be displayed each time the machine is turned on until 5 drinks including steam have been prepared The displays light 62 You will then be prompted to select a language m Turn the right jog shuttle until the desired language shows in the display m Press the right jog shuttle to confirm To turn off the machine m Press and hold the left jog shuttle until the displays go dark Installation Setting the water hardness The hardness of the water used in the coffee system must be determined and programmed into the appliance The water hardness will determine how frequently the unit must be descaled to properly maintain the coffee system The machine monitors the volume of water passing through it in conj
31. her level e g upper cabinets Plastic drip grill Metal drip catch Coffee dispenser Inset for Cappuccinatore Valve Lever for steam and hot water Guide to the machine Interior view Main switch 4 Capsule carousel 19 Capsule plate l Carousel tray replaced with the descaling funnel when descaling is performed Water tank Perforator Drip tray with grid not visible penetrates capsule to grid avoids spilling during transport assist in the brewing process Waste container Displays Left display Right display costs TE 2 T ca S Eo DI i tw Drink selection selects coffee or espresso Up to 5 different coffee types as _ shows current actions e g heating well as steam amp and hot water i prompts an action e g close the User profile door Up to 4 different users Important maintenance Rinsing Fi descaling S Selection of Settings Individual settings and information can be selected in the right hand display Language Time Allocation of coffee type User name Programming eed t ZO F Total number of cups of coffee dispensed to date mi Maintenance ty Reset to default settings The selected option will be highlighted in the display 10 First steps to use Turning the machine on and off Turning on The appliance must be correctly installed and connected before the first use m Press the left jog shuttle
32. his option to on so that the rinsing process will not be forgotten The display now shows the main screen The back symbol is selected m Press the right jog shuttle to return to the main display menu 33 Settings Steam system To conserve energy the steam system can be turned off if steam is not used all the time Residual heat may allow the machine to dispense some steam when the steam system is turned off Use caution m Turn the right jog shuttle to the Programming symbol press to confirm m Turn the right jog shuttle to the Steam system option Press to confirm 34 STEAM SYSTEM CE gt m Turn the right jog shuttle to select on or off A check marks the current setting m Press the right jog shuttle to save the settings The display now shows the previous screen The back symbol is selected m Press the right jog shuttle to return to the main display menu Settings Total coffee counter INFO If the option Info is selected the display will show the number of cups of coffee dispensed to date espresso coffee double espresso coffee SETTINGS Pe m Turn the left jog shuttle to Settings INFO Pmi gt m Turn the right jog shuttle to the Info symbol press to confirm The number of coffees already dispensed will appear in the display m Press the right jog shuttle to return to the main screen of the display Facto
33. in the 12 o clock position between the hot milk and froth symbols m Re assemble the lid as shown in the illustration When replacing the valve be sure the dot is facing the upper right 42 Descaling the appliance The coffee system must be descaled regularly The time period depends on the water hardness set The appliance will display a reminder message and will eventually lock if not descaled Once the system is at the point where only 50 drinks can be prepared before descaling must be performed the display will show 50 no of uses until descaling has to be done This message will appear and countdown after each drink When the count is to zero the coffee system will lock and the left display will show Descale The right display will show confirm to start The appliance can only be used again once descaling is performed Only use the enclosed descaling tablets for descaling The descaling tablets are specially designed for this coffee system The descaling tablets can be purchased from your local Miele dealer or Miele Other agents may damage the machine and affect the taste of coffee and hot water Be sure that the correct mixture of descaling agent and water are used to prevent damage to the machine To prevent damage to the exterior wipe up any descaling solution spills immediately Thoroughly clean the water tank and the drip tray of descaling residue Descaling m Turn the left k
34. isposal of packing material The cardboard box and packing materials protect the appliance during shipping They have been designed to be biodegradable and recyclable Please recycle Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of children Danger of suffocation Disposal of an old appliance Old appliances may contain materials that can be recycled Please contact your local recycling authority about the possibility of recycling these materials Ensure that the appliance presents no danger to children while being stored for disposal Before discarding an old appliance unplug it from the outlet cut off its power cord and remove any doors to prevent hazards 67 Please have the model and serial number of your appliance available before contacting Technical Service U S A Miele Inc National Headquarters 9 Independence Way Princeton NJ 08540 Phone 800 843 7231 609 419 9898 Fax 609 419 4298 www miele com Technical Service amp Support Nationwide Phone 800 999 1360 Fax 888 586 8056 TechnicalService mieleusa com Canada Miele Limited Headquarters and Showroom 161 Four Valley Drive Vaughan ON L4K 4V8 Phone 800 643 5381 905 660 9936 Fax 905 532 2290 www miele ca info miele ca general enquiries professional miele ca commercial enquiries MieleCare National Service Phone 800 565 6435 905 532 2272 Fax 905 532 2292 cust
35. istretto is a double strength bitter tasting espresso Macchiato is espresso with a dollop of hot foamed milk giving a dappled macchiato appearance Pre warming the cup is recommended to prevent the espresso from cooling too quickly The Espresso range Ristretto black is the typical Italian espresso It is a short strong full bodied espresso with a touch of acidity It has a pleasantly lingering taste Strength 10 Ideal cup size Ristretto Espresso or Cappuccino Arpeggio dark purple is a Mediterranean blend par excellence with a strong character intense body and long exquisite after taste Its thick smooth crema remains to the last sip Strength 9 Ideal cup size Ristretto Espresso or Cappuccino Roma dark gray With its sweetness and its woody notes Roma is the ideal coffee for a short espresso that is not too strong Strength 8 Ideal cup size Ristretto or Espresso Decaffeinato Intenso brick red An intense rich taste with slightly elevated acidity gives this decaffeinated coffee all the strength of a true espresso Strength 7 Ideal cup size Espresso or Cappuccino Livanto copper brown A very well balanced blend Livanto is characterized by a dense and velvety aroma It is a uniquely rounded espresso Strength 6 Ideal cup size Espresso or Lungo Capriccio dark green is a full bodied espresso which is also creamy mild and rich Its crema is very dense and so de
36. licate that it reflects the light Strength 5 Ideal cup size Espresso Volluto yellow gold Lightly roasted but full bodied Volluto s flavor is round and fresh with a cereal hint Volluto s character is reinforced by a touch of acidity Strength 4 Ideal cup size Espresso Cosi dark brown is perfect for espresso lovers who enjoy a mild smooth crema coupled with the refreshing acidity of a hint of lemon Strength 3 Ideal cup size Espresso or Lungo Decaffeinato red This is the lighter and creamier decaffeinated blend offering a rich and delicate balance between mildness and acidity Decaffeinato s crema is distinguished by its hazel color and consistent texture in the mouth Strength 2 Ideal cup size Espresso or Lungo 65 The Lungo range Vivalto sky blue is an intense Lungo which combines a beautifully roasted note with a subtle floral note With its noticeable crema and mild aroma it is also delicious prepared with milk Strength 6 Ideal cup size Lungo Decaffeinato Lungo coral delivers a smooth body and a fine roundness in the mouth Its sustained roasting reveals flavorful grilled notes Strength 5 Ideal cup size Lungo Finezzo butter yellow Extremely balanced Finezzo is a mellow gently fruity blend that blossoms within its light body Its character is reinforced by a hint of acidity Strength 4 Ideal cup size Lungo 66 Caring for the environment D
37. n insert it again What if no coffee is prepared although water is in the tank and coffee capsules are in the carousel A coffee capsule is jammed in the carousel m Open the appliance door m Pull the carousel tray out lift out the capsule carousel and make sure all capsules can move easily m Insert the carousel in the tray and push it all the way in m Close the door What if no hot water or steam is dispensed from the steam valve m Take out the water tank and then insert it again If still no or little water is dispensed the steam valve is clogged m Open the appliance door m Press the steam lever down and pull off the rubber sleeve m Using the small end of the provided tool unscrew the top of the steam valve counterclockwise m Clean the tip and screw it on again 49 Frequently asked questions What if the steam heating system is turned off but steam can still be dispensed Steam can be dispensed as long as the steam heating system is warm Once cooled the system will no longer dispense steam What if the steam smells like rubber The rubber odor will wear off with time and usage What if the cappuccinatore dispenses no frothed milk ls the spout turned to the side so that froth can only be prepared in the cappuccinatore Are the valve and the froth dispenser of the cappuccinatore properly inserted in the lid Are any single parts
38. n of water and liquid dish soap m Reattach the rubber sleeve firmly on the steam valve tip m Push the steam lever up before closing the door or else it may get damaged 39 Cleaning and care Exterior The front of the appliance can be cleaned with a sponge and a solution of warm water and non abrasive liquid dish soap Dry with a soft cloth Only use a slightly damp sponge when cleaning the controls Water could penetrate into the electronics and cause damage Wipe any spills from descaling immediately Stainless steel surfaces Stainless steel surfaces can be cleaned using a non abrasive stainless steel cleaner To help prevent soiling a conditioner for stainless steel can also be used Apply sparingly with even pressure Jog shuttles Clean the jog shuttles with a sponge and a solution of warm water and liquid dish soap m These jog shuttles may become discolored or damaged if not cleaned regularly Do not use a stainless steel cleaner on the jog shuttles 40 Maintenance The perforator should be changed after 15000 cups of coffee espresso The perforator can be purchased from Miele It is recommended to contact the Miele Service department for assistance in performing this maintenance task m Turn the left jog shuttle to Settings MAINTENANCE m Turn the right jog shuttle to Maintenance MAINTENANCE carry out a m Press the right jog shuttle and turn it to carry
39. n the carousel tray niche Dry with a soft cloth The carousel chambers are read by the sensor m Clean the sensors left and right in the waste container niche The sensors read if the waste container is inserted and if it needs to be emptied 38 Drip tray m Clean and dry the metal contacts at the back of the drip tray If the contacts are soiled or wet the unit cannot read when the drip tray is full and needs to be emptied m Push the drip tray with the grid inserted along the right hand side of the opening and to the back of the machine Close the door Coffee dispenser cover m Push in and up to remove Cover is dishwasher safe Cleaning and care Capsule plate The capsule plate will soil more or less depending on the oil content of the coffee capsule used Clean the capsule plate as necessary or when the machine needs to be descaled with the supplied cleaning tablets The cleaning tablets can be purchased from Miele m Press the checkered part down and pull the capsule plate out m Dissolve one cleaning tablet in hot water m Place the capsule plate in the solution and let it soak for one hour m Rinse thoroughly and dry the capsule plate m Insert the capsule plate into the machine until it clicks into place Steam valve m Press the steam lever down and pull off the rubber sleeve m Clean the rubber sleeve and the steam valve tip with a mild solutio
40. nob to the Descaling symbol Confirmto start m Press the right jog shuttle to start the descaling process The descaling cannot be interrupted once the right knob is pressed This is a safety feature to ensure the process will be completed Descaling is important to increase the life of the machine and to ensure the best results possible 43 Descaling the appliance The right display will prompt you through the single steps of the descaling process Follow these prompts See Descaling prompts for more information Do not skip any steps and do not remove a part unless prompted by the display This will cause the program to fault and descaling will restart 44 At the beginning of the descaling program there will be a delayed start to allow the tablets to completely dissolve If the machine has not sufficiently cooled after use to begin the descaling program the delay start time will be extended A pump will introduce a small amount of descaling solution into the system then rest briefly to allow the solution to take effect The right display indicates how long the process will take Descaling the appliance Descaling prompts For clarification regarding the prompts see the following Please add descaling agent to the water container m Remove the water tank m Fill the water tank with cold tap water to the S mark If not filled to the mark descaling will be prematurely canceled m
41. nserted all the way Take the capsule plate out and insert it again What if the coffee is too thin Check the water amount saved in the memory per coffee After 15 000 cups of coffee the perforator needs to be replaced Adjust if necessary See Common coffee system care Maintenance after checking the coffee counter 51 Frequently asked questions Descaling problems What if the descaling process was started accidently The descaling process cannot be interrupted once the right jog shuttle is pressed The process now needs to be completed as a safety measure Descaling is important to increase the life of the machine and to ensure the best results possible What if the preheating time is increased the water flow amount is not correct and the unit performs less The machine needs to be descaled See Descaling the appliance 52 Frequently asked questions F messages What if F 10 shows No water can be pumped from the water tank F 10 also shows if the water tank was not filled correctly during descaling Fill the system with water See Before using the coffee system for the first time Remove and reinsert the water tank Refill to the mark and restart descaling If the message still shows contact Technical Service What if F 42 or F 45 shows briefly in the right display when the machine is turned off
42. o confirm and the drink will be dispensed Interrupting the brewing m Press the right jog shuttle to interrupt the coffee dispensing immediately For coffee espresso recipes see the Coffee glossary Dispensing hot water Hot water m Place a cup under the hot water steam valve HOT WATER m Turn the left jog shuttle to Hot water m Press the right jog shuttle to confirm m Press again to stop the water from dispensing Making coffee Cappuccinatore milk froth mug This appliance includes a Cappuccinatore milk froth mug which can be used to easily prepare warm milk frothed milk and Cappuccino Before using the cappuccinatore for the first time wash it either in the The steam is regulated by turning the valve dishwasher or with hot water and Left hot milk is prepared liquid dish soap Right froth is prepared See Common coffee system care Be sure not to set the valve between these two settings this may cause the milk to splatter When milk is frothed in the cappuccinatore the froth is hotter Above the handle on the and has more volume cappuccinatore there is a valve and a milk spout on the side When frothing milk into a cup while dispensing a coffee the steam Cold milk is best for creating froth system must be turned on See Settings Steam system 20 Making coffee Pushed in Milk is frothed into the cup Pulled out Milk is frothed into the
43. omercare miele ca technical enquiries Alteration rights reserved 0409 CVA 2660 For the most updated manual see the Miele web site M Nr 07 173 890 01
44. out m Press the right jog shuttle Cleaning and care The right display goes dark and the appliance is now lowering the perforator temave capsule plate and change the capsule m Open the appliance door m Pull out the capsule plate Do not reach up into the m Screw the new perforator firmly into perforator opening Danger of injury the unit The spring and ball bearing must be inserted in the perforator opening so that the ball bearing is on top m Insert the rubber disc from the bottom up with the funnel pointing downwards m Insert the capsule plate and close the door m Pull the rubber disc top down and out m Insert the tool for removing the perforator up into the unit Turn it to the left to loosen and remove the perforator 41 Cleaning and care Cappuccinatore Be sure that the parts are assembled properly e g no gap between each Clean the cappuccinatore after every half ofthe lid use otherwise it may become blocked RSI A e a Be sure that the re assembled lid is The cappuccinatore can be seated correctly on the pitcher The disassembled into parts for thorough valve belongs over the handle of the cleaning For best results use a cappuccinatore If the valve is in the dishwasher all parts are wrong position the cappuccinatore will dishwasher safe not work properly m Separate the lid remove all parts and clean To remove the valve the dot needs to be
45. ry setting This option allows you to reset all saved settings to the factory default SETTINGS f m Turn the left jog shuttle to Settings FACTORY DEFAULT m Turn the right jog shuttle to the Factory default symbol m Press to confirm FACTORY DEFAULT gt m Turn the right jog shuttle to select reset FACTORY DEFAULT m Select back to go back to the previous screen without changing the settings in the memory m Press to confirm System lock The coffee system can be locked so that it cannot be used by children or those not familiar with the operating instructions 36 Locking the coffee system m Turn the coffee system off by pressing the left jog shuttle SUSTEMLOCK cf m Turn the right jog shuttle until the display shows System lock m Press to confirm SWSTEMLOCE ef en m Turn the jog shuttle to on and press to activate the system lock The appliance is now locked and will not operate The system will remain locked and the lighting will remain turned off even if the jog shuttles are turned When the jog shuttles are pressed or turned the display shows Machine is locked amp Unlocking the coffee system m Follow the steps for Locking the coffee system but select off to deactivate the system lock The appliance is now unlocked and ready for use Cleaning and care Daily coffee system care The following components of the coffe
46. ss the right jog shuttle again to turn the hot water off m Turn the left jog shuttle to Heating with steam m Press the steam lever down m Push the steam lever up when steam starts to be dispensed The lines are filled and the coffee system is ready to use 12 Filling water and coffee capsules Filling the water tank The water tank should be washed and filled with fresh cold tap water before each day of use Never put hot water or any other liquid except cold water into the water tank m Lift the water tank and pull it out m Fill the container with fresh cold tap water to the Max mark A valve at the tank front prevents leaks m Push the water tank back into the machine Filling water and coffee capsules Filling the coffee capsule carousel Only insert Nespresso coffee capsules in the carousel Damaged broken or dented capsules should not be used they may jam in the machine There are five chambers each can hold four capsules The coffee types have to be allocated to their respective chambers to get the desired coffee type You can also fill each chamber with the same coffee type The chambers are factory set for a coffee type Fill the chambers respectively or program other coffee types according to your preference See Allocating various coffee types 14 m Pull the carousel tray all the way out m Take the carousel out m Insert the capsules into th
47. to save the settings The display shows the previous screen The back symbol is selected m Press the right jog shuttle to display the main menu m Turn the right jog shuttle to the Programming symbol press to confirm LIGHTING m Turn the right jog shuttle to the desired option Lighting Display contrast Q Display brightness it m Press to confirm A bar shows in the display m Turning the right jog shuttle counterclockwise reducing the bar size will decrease the lighting display contrast and brightness 32 Settings Automatic rinsing The rinsing feature flushes out coffee residue and pre warms the coffee system When Automatic rinsing on is selected the system will automatically be rinsed when the appliance is turned on or off Heating up please wait is shown in the display If this feature is set to Automatic rinsing off the system will only be flushed and pre warmed when selected manually m Place an empty cup under the coffee dispenser SETTINGS P m Turn the left jog shuttle to Settings PROGRAMMING m Turn the right jog shuttle to the Programming symbol press to confirm AUTOMATIC RINSING m Turn the right jog shuttle to the Automatic rinsing option Press to confirm AUTOMATIC RINSING CE gt m Turn the right jog shuttle to select on or off press to confirm A check marks the current setting It is recommended to set t
48. uccinatore spout into the out position m Turn the valve all the way to the left for heating m Place the cappuccinatore under the steam valve m Slowly press the steam lever down and carefully connect the valve to the cappuccinatore Making coffee Rinsing the lid For a quick cleaning between froths the cappuccinatore lid can be rinsed with the steam valve The rinsing does not replace the cleaning of the cappuccinatore in a dishwasher m Turn the left jog shuttle to the Rinse setting m Push the cappuccinatore spout into the in position m Place an empty cup under the spout m Press the steam lever down In the right hand display you will see Rinsing coppuccinatore Hot water now runs through the lid and flushes it clean The process will stop automatically when the lid is rinsed 23 Setting serving sizes The flavor of the coffee depends on the coffee type and the quantity of water used To ensure the machine uses exactly the amount of water to suit your taste and your cup size there is a choice of two serving sizes for espresso coffee The espresso symbol dispenses a standard size espresso The espresso water amount can be set between 1 and 2 5 oz 30 and 75 ml W The coffee symbol dispenses coffee for a standard size coffee cup It uses the same quantity of coffee as an espresso but adds more water The water amount can be set between 1 and 6 oz 30 and 175 ml
49. unction with the hardness of the water and will indicate when descaling is necessary Your local water authority can inform you of the hardness of your tap water or you can measure the hardness yourself using the enclosed test strip m Dip the strip into your tap water for one second then shake off any excess water The result will be evident after one minute If your water hardness is greater than 40 gr gal 700 ppm the water must be mixed in equal parts with non carbonated mineral water to prevent excessive lime scale build up Never use distilled water Program Water gr gal ppm setting Hardness Hardness 1 1 soft 0 3 0 130 Hardness 2 1 soft 4 7 130 250 Hardness 3 2 medium 7 14 250 380 Hardness 4 3 hard 14 21 over 380 4 very hard over 21 To adjust or set the water hardness m Turn the right jog shuttle to the Programming symbol press to confirm m Turn the right jog shuttle to the Water hardness symbol press to confirm WATER HARDMESS Mi very hard 4 gt m Turn the right jog shuttle to set the water hardness A check marks the current setting m Press the right jog shuttle to save the setting The display now shows the main screen The back symbol 4 is selected m Press the right jog shuttle to return to the main display menu 63 Coffee glossary Caff is the Italian term for a standard espresso Caff

Miele Coffeemaker CVA 2660 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents