Maytag MGR8600DS Dimension Guide
Contents
1. same room but external to the range opening such as an adjacent cabinet It should be in a Range can be raised approximately 1 2 5 cm by adjusting the leveling legs location that allows ease of opening and closing Do not block access to shutoff valve The valve Front of door and drawer may extend farther forward depending on styling is for turning on or shutting off gas to the range B Electrical A J A Gas supply line A 120 volt 60 Hz AC only 15 amp fused electrical circuit is required A time delay B Shutoff valve open position fuse or circuit breaker is also recommended It is recommended that a separate gt C To range circuit serving only this range be provided CABINET OPENING SAL SONE T TEFLON is a registered trademark of E l Du Pont De Nemours and Company Cabinet opening dimensions shown are for 25 64 0 cm countertop depth 24 61 0 cm base cabinet depth and 36 91 4 cm countertop height IMPORTANT If installing a range hood or microwave hood combination above the range follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface A 18 45 7 cm upper side cabinet to countertop B 13 33 cm max upper cabinet depth C 30 76 2 cm min opening width D For minimum clearance to top of cooktop see NOTE E 30 76 5 cm min opening width F The shaded areas are recommended for installation of rigid gas pipe G2. ANAVE 30 76 2 cm Freestanding Gas Range PRODUCT MODEL NUMBERS PRODUCT DIMENSIONS MGR8600D MGR8674A MGR8775A MGR8850D MGR8885A MGR8670A MGR8700D MGR8800D MGR8880A Type of Gas Natural Gas This range is design certified by CSA International for use with Natural gas or after proper conversion for use with LP gas This range is factory set for use with Natural gas See Gas Conversions section The model serial rating plate located on the oven frame behind the top right side of the oven door has information on the types of gas that can be used If the types of gas listed do not include the type of gas available check with the local gas supplier LP gas conversion Conversion must be done by a qualified service technician No attempt shall be made to convert the appliance from the gas specified on the model serial rating plate for use with a different gas without consulting the serving gas supplier See Gas Conversions section Gas Supply Line Provide a gas supply line of 4 1 9 cm rigid pipe to the range location A smaller size pipe on longer runs may result in insufficient gas supply With LP gas piping or tubing size can be 4 1 3 cm minimum Usually LP gas suppliers determine the size and materials used in the system NOTE Pipe joint compounds that resist the action of LP gas must be used Do not use TEFLON tape Flexible metal appliance connector e If local codes permit a
3. 11 27 9 cm H 17 43 2 cm 1 2 5 1 cm J 4 11 4 cm K 3 7 6 cm min clearance from both sides of range to side wall or other combustible material L Grounded outlet M Cabinet door or hinges should not extend into the cutout NOTE 24 61 0 cm minimum when bottom of wood or metal cabinet is covered by not less than 1 4 0 64 cm flame retardant millboard covered with not less than No 28 MSG sheet steel 0 015 0 4 mm stainless steel 0 024 0 6 mm aluminum or 0 020 0 5 mm copper 30 76 2 cm minimum clearance between the top of the cooking platform and the bottom of an uncovered wood or metal cabinet Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only For complete details see Installation Ref W10553363A our products we reserve the right to change materials and specifications without notice Instructions packed with product Specifications subject to change without notice 5 14
4. new CSA design certified 4 to 5 ft 122 to 152 4 cm long 1 3 cm or 34 1 9 cm I D flexible metal appliance connector may be used for connecting range to the gas supply line A 1 2 1 3 cm male pipe thread is needed for connection to the A 277 70 8 cm max depth with handle B 36 91 4 cm cooktop height max with leveling legs screwed all the way in female pipe threads of the inlet to the appliance pressure regulator C 46 119 1 cm overall height max with leveling legs screwed all the way in D 297 75 9 cm width E 25746 64 6 cm depth Back of range to front of cooktop F Model serial rating plate located on the oven frame behind Do not kink or damage the flexible metal tubing when moving the range Rigid pipe connection The rigid pipe connection requires a combination of pipe fittings to obtain an in line connection to the range The rigid pipe must be level with the range connection All strains must be removed from the supply and fuel lines so range will be j D the top right side of the oven door 2 level and in line IMPORTANT Range must be level after installation Follow the instructions in the e Must include a shutoff valve Level Range section Using the cooktop as a reference for leveling the range is not recommended The supply line must be equipped with a manual shutoff valve This valve should be located in the a 2
Download Pdf Manuals
Related Search