Makita HM1306 User's Manual
Contents
1. e Taa kita mer 008264 nd UNDERSTAND before using OR FUTURE REFERENCE ENGLISH SPECIFICATIONS Model HM1306 Blows per minute 1450 min Overall length 652 mm Net weight 15kg Due to our continuing programme of research and development the specifications herein are subject to change without notice Note Specifications may differ from country to country END103 2 Symbols The following show the symbols used for the equipment Be sure that you understand their meaning before use CR Read instruction manual K Only for EU countries Do not dispose of electric equipment together with household waste material In observance of European Directive 2002 96 EC on waste electric and electronic equipment and its implementation in accordance with national law electric equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility ENE046 1 Intended use The tool is intended for heavy chiselling and demolition work as well as for driving and compacting with appropriate accessories ENF001 1 Power supply The tool should be connected only to a power supply of the same voltage as indicated on the nameplate and can only be operated on single phase AC supply This tool should be grounded while in use to protect the operator from electric shock Use only three wire extension cords which have three prong groun2. it on Avoid unintentional starting Do nat carry a plugged in tool with a finger on the switch Ensure switch is off when plugging in Use outdoor extension leads When tool is used outdoors use only extension cords intended for outdoor use Stay alert Watch what you are doing Use common sense Do not operate tool when you are tired Check damaged parts Before further use of the tool a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment of moving parts free running of moving parts breakage of parts mounting and any other conditions that may affect its operation A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated in this instruction manual Have defective switches replaced by an authorized service facility Do not use the tool if the switch does not turn it on and off Warning The use of any accessory or attachment other than those recommended in this instruction manual or the catalog may present a risk of personal injury 22 Have your tool repaired by a qualified person This electric tool is in accordance with the relevant safety requirements Repairs should only be carried out by qualified persons using original spare parts otherwise this may result in considerable danger to the user ENB049 3 ADDITIONAL SAFET
3. operation they may be extremely hot and could burn your skin PROPER GROUNDING This tool should be grounding while in use to protect the operator from electric shock 15 EXTENSION CORDS Use only three wire extension cords which have three prong grounding type plugs and three pole receptacles which accept the tool s plug Replace or repair damaged or worn cord immediately 16 Do not operate the tool at unnecessarily SAVE THESE INSTRUCTIONS no load FUNCTIONAL DESCRIPTION ACAUTION Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool Switch action 1 Lock button 2 Switch trigger A CAUTION Before plugging in the tool always check to see that the switch trigger actuates properly and returns to the OFF position when released To start the tool simply pull the switch trigger Release the switch trigger to stop For continuous operation pull the switch trigger and then slide down the lock button To stop the tool from the locked position pull the switch trigger fully then release it ASSEMBLY ACAUTION Always be sure that the tool is switched off and unplugged before carrying out any work on the tool Installing or removing the bit 1 Bull point 2 Notched portion 3 Tool retainer 4 Tool holder With the notched portion on the shank of the bit facing toward the tool retainer insert the bit into the tool holder as far as it wi
4. Y RULES 10 11 Wear ear protectors Exposure to noise can cause hearing loss Use auxiliary handles supplied with the tool Loss of control can cause personal injury Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord Contact with a live wire will make exposed metal parts of the tool live and shock the operator Wear a hard hat safety helmet safety glasses and or face shield It is also highly recommended that you wear a dust mask and thickly padded gloves Be sure the bit is secured in place before operation Under normal operation the tool is designed to produce vibration The screws can come loose easily causing a breakdown or accident Check tightness of screws carefully before operation In cold weather or when the tool has not been used for a long time let the tool warm up for a while by operating it under no load This will loosen up the lubrication Without proper warm up hammering operation is difficult Always be sure you have a firm footing Be sure no one is below when using the tool in high locations Hold the tool firmly with both hands Keep hands away from moving parts Do not leave the tool running Operate the tool only when hand held Do not point the tool at any one in the area when operating The bit could fly out and injure someone seriously Do not touch the bit or parts close to the bit immediately after
5. ding type plugs and three pole receptacles which accept the tool s plug ENA001 2 SAFETY INSTRUCTIONS WARNING When using electric tools basic safety precautions including the following should always be followed to reduce the risk of fire electric shock and personal injury Read all these instructions before operating this product and save these instructions For safe operations 1 2 Keep work area clean Cluttered areas and benches invite injuries Consider work area environment Do not expose power tools to rain Do not use power tools in damp or wet locations Keep work area well lit Do not use power tools where there is risk to cause fire or explosion Guard against electric shock Avoid body contact with earthed or grounded surfaces e g pipes radiators ranges refrigerators Keep children away Do not let visitors touch the tool or extension cord All visitors should be kept away from work area Store idle tools When not in use tools should be stored in a dry high or locked up place out of reach of children Do not force the tool It will do the job better and safer at the rate for which it was intended Use the right tool Do not force small tools or attachments to do the job of a heavy duty tool Do not use tools for purposes not intended for example do not use circular saws to cut tree limbs or logs Dress properly Do not wear loose clothing or jewellery they can be caught in moving part
6. irmly 1 Wrench 2 Oil gauge 1 Oil supply To replenish remove the oil gauge with the wrench 23 Use only Makita genuine oil The use of any other oil may harm the tool To maintain product SAFETY and RELIABILITY repairs any other maintenance or adjustment should be performed by Makita Authorized Service Centers always using Makita replacement parts ACCESSORIES ACAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons Only use accessory or attachment for its stated purpose If you need any assistance for more details regarding these accessories ask your local Makita Service Center Bull point Cold chisel Scaling chisel Clay spade Rammer Oil supply Wrench 23 Steel carrying case Makita Corporation 884757 9
7. ll go Then pull out and turn the tool retainer 180 to secure the bit After installing always make sure that the bit is securely held in place by trying to pull it out Side handle auxiliary handle 1 Side handle The side handle swings around to either side allowing easy handling of the tool in any position OPERATION Chipping Scaling Demolition Hold the tool firmly with both hands Turn the tool on and apply slight pressure on the tool so that the tool will not bounce around uncontrolled Pressing very hard on the tool will not increase the efficiency MAINTENANCE ACAUTION Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance Replacing carbon brushes 1 Commutator 2 Insulating tip 3 Carbon brush When the resin insulating tip inside the carbon brush is exposed to contact the commutator it will automatically shut off the motor When this occurs both carbon brushes should be replaced Keep the carbon brushes clean and free to slip in the holders Both carbon brushes should be replaced at the same time Use only identical carbon brushes Use a hex wrentch to remove the holder cap plates 1 Hex wrench 2 Holder cap plate Use a screwdriver to remove the brush holder caps Take out the worn carbon brushes insert the new ones and secure the brush holder caps 1 Screwdriver 2 Brush holder cap Reinstall the holder cap plates f
8. s Rubber gloves and non skid footwear are recommended when working outdoors Wear protecting hair covering to contain long hair Use safety glasses and hearing protection Also use face or dust mask if the cutting operation is dusty Connect dust extraction equipment If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used Do not abuse the cord Never carry the tool by the cord or yank it to disconnect it from the socket Keep the cord away from heat oil and sharp edges 12 13 14 15 16 17 18 19 20 21 Secure work Use clamps or a vice to hold the work It is safer than using your hand and it frees both hands to operate the tool Do not overreach Keep proper footing and balance at all times Maintain tools with care Keep cutting tools sharp and clean for better and safer performance Follow instructions for lubrication and changing accessories Inspect tool cord periodically and if damaged have it repaired by an authorized service facility Inspect extension cords periodically and replace if damaged Keep handles dry clean and free from oil and grease Disconnect tools When not in use before servicing and when changing accessories such as blades bits and cutters Remove adjusting keys and wrenches Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning
Download Pdf Manuals
Related Search