Magnadyne PPC-200 User's Manual
Contents
1. NO IMPLIED WARRANTY SHALL EXTEND BEYOND 1 YEAR FROM THE DATE OF SALE This warranty extends only to the original purchaser of the product and is not transferable Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitations or exclusion may not apply to you This warranty gives you specific legal rights and you may have other rights that vary from state to state Defective merchandise should be returned to the original point of purchase or secondly to Magnadyne Corporation 1111 W Victoria Street Compton CA 90220 or 2061 Cohen Street Montreal Quebec H4R 2N7 Return Authorization must be obtained before sending or merchandise may be refused2. to adjust the time and to the right to adjust the minutes 5 Once the correct time is showing in the display let the display change back to the radio station before turning the unit off CONTROLS AND OPERATIONS How to Preset Radio Stations Repeat the following procedures to memorize radio stations 1 Turn on the unit by rotating the volume control knob to the right 2 Select the radio band FM1 FM2 AM1 you want to memorize radio stations in by pressing the FM AM button 3 Use the manual tuning button to select a radio station you want to set into memory 4 Press the memory button ME and release it A CH indicator will begin to flash in the display area 5 Press the station recall button you want that station memorized on 1 6 6 Select the next band FM1 FM2 AM1 and repeat steps 3 4 and 5 to memorize radio stations on all bands INSTALLING THE RADIO 1 Anchoring Board 2 Flat Washer 3 Machine Screw 4 Mounting Strap 5 Hex Nut 6 Shaft Nut 7 Dashboard 8 Trim Plate Installing the Radio 4 Support the rear of the chassis using the 1 Locate the factory supplied opening for the radio or choose a location within reach of perforated back strap and nuts supplied the primary operator of the vehicle Attach the back strap to the rear chassis of 2 Cut and file the opening if necessary so the shafts and the nosepiece of the radio will the radio and find a secure solid location slide through the openi
3. to listen to by repeated pressing of the FM AM button Recall Button 10 Pressing the recall button will change the display from the radio frequency to the clock If you want to see the time in the display simply press the recall button and the clock will appear for 5 seconds Local Distant Button 11 Switch the LO DX button to the LO position to prevent strong local stations from overlapping weaker stations For normal operation and maximum sensitivity switch to the DX position Note When in the LO mode LOC will be displayed in the display area Multi Function LCD Area 12 The LCD display area will indicate the following operating functions Radio frequency and clock time FM1 FM2 and AM1 radio bands Local radio reception mode and last preset memory button pushed Display Priority The priority of the PPC 200 display area is dedicated to the radio frequency If the recall button is pushed to see the time the display will always change back to the clock after 5 seconds How to Set the Time Repeat the following procedures to properly set the clock time 1 Turn on the unit by rotating the volume control knob to the right 2 Press the recall button to turn the display from the radio frequency to the clock mode 3 Press and release the memory button while the clock time is displayed in the LCD area the time showing will begin to flash 4 While the display is flashing rotate the time set control knob to the left
4. Owner s Manual AM FM Stereo Receiver with Digital Clock Seek Scan Manual Tuning Model PPC 200 CONTROLS AND OPERATIONS 12 8 10 5 VULUME TUNE ON OFF AVER gt ime TUNING tush BALANUE On Off Volume Balance Control Knob 1 To turn the unit on rotate the the volume control knob to the right To adjust the the volume level continue rotating the knob to the right To turn the unit off rotate the knob to the left until it clicks Push in on the volume knob and rotate the knob from left to right to change the relative output of the left and right speakers Adjust the balance control to your listing preference Tone Control Knob 2 Rotating the tone control knob from right to left will adjust the overall tone quality higher or lower Make the tone adjustment to your desired preference 11 6 3 4 Fader Control Knob 3 Rotating the fader control knob from left to right will change the relative output level of the front or rear speakers Adjust the fader control to your listening preference Time Set Control Knob 4 The time set control knob is used in conjunction with the memory button ME to set the clock Please refer to the how to set the clock section of this manual for further details Station Recall Buttons 5 The station recall buttons are used in conjunction with the memory ME button to memor
5. ge Wire with fuse holder Connect the orange wire to a constant 12 volt power source The fuse block of the vehicle will provide a good connection point Use a test light or volt meter to locate the proper point of connection If a proper connection point can not be found at the fuse block connect the orange wire directly to the post on the battery Yellow Wire The yellow wire will provide 12 volts when the on off control of the radio is switched to on The yellow wire is used to trigger a power antenna relay Connect the yellow wire to the positive trigger wire of the power antenna relay Black Wire Connect the black wire to the frame of the vehicle Crimp a ring terminal to the black wire and use a nut a bolt to secure it to the vehicle chassis A good ground is essential for proper performance of the PPC 200 unit Brown Wire Connect the brown wire to the positive terminal of the left front speaker Gray Wire Connect the gray wire to the positive terminal of the right front speaker Green Wire Connect the green wire to the positive terminal of the left rear speaker Blue Wire Connect the blue wire to the positive terminal of the right rear speaker White Wire Connect the white wire to the negative terminals of all speakers used for the right channel Orange Wire Connect the orange wire to the negative terminal of all speaker used for the left channel Note In the wiring diagram there is more than one whi
6. id product or part is found defective in materials or workmanship when properly connected and operating on the correct power requirements designated for the specific product This warranty and Magnadyne Corporation or its authorized agents obligations hereunder do not apply where the product was damaged while in the possession of the consumer subjected to unreasonable or unintended use not reasonably maintained utilized in commercial or industrial operations or serviced by anyone other than Magnadyne Corporation or its authorized agents or where the warning seal on the product is broken or the power and or plugs are detached from the unit Magnadyne Corporation or any of its authorized agents will not assume any labor costs for the removal and re installation of any product found to be defective or the cost of transportation to Magnadyne Corporation or its authorized agents Such costs are the sole responsibility of the purchaser This warranty does not cover the cabinet appearance items or accessories used in connection with this product or any damaged to recording or recording tape or any damage to the to the products resulting from improper installation alteration accident misuse abuse or acts of nature MAGNADYNE CORPORATION OR ITS AUTHORIZED AGENTS SHALL NOT BE LIABLE TO ANYONE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR CLAIMS EXCEPT THOSE ACCORDED BY LAW NO EXPRESSED WARRANTY OR IMPLIED WARRANTY IS GIVEN EXCEPT THOSE SET FORTH HEREIN
7. ize desired radio stations and recall them See the How to Preset Radio Stations section of this manual for further details CONTROLS AND OPERATIONS Seek Scan Button 6 Pressing the seek button will cause the tuner to search out the next strongest station up the tuning scale To continue seeking you must repeatedly press the seek button each time the tuner stops on a station Pressing the scan button will put the tuner into scan mode When in the scan mode the tuner will seek up to the next strongest radio station and stop for eight seconds After 8 seconds the tuner will again seek up to the next strongest stations and hold for 8 seconds To stop the scan mode simply press the scan button once again and the tuner will stop scanning Manual Up Down Tuning 7 To manually tune a station up or down the scale simply press the the up or down side of the manual tuning button Hold the button down until you get close to the station and release it Fine tune by pressing the button repeatedly Memory Button 8 The memory button is used with the station recall buttons and the clock set button to program radio stations and set the clock See how to set the clock and how to preset radio stations for more details FM AM Select Button 9 Repeated pressing of the FM AM button will change the tuner from FM1 band to FM2 band and to AM operation The particular band will be displayed in the display area Select the band you wish
8. ng to attach the end of the back strap 3 Place the spacing nuts and washers on the shafts and adjust them so that the nosepiece Note Reluctance to use or properly and shafts stick through the mounting far enough for the face plate to be positioned and install the back strap will result in held into place using the remaining nuts and washers If the face plate is not used damage to the shafts and will cause the adjust the radio depth so that the knobs will fit and operate smooth and correctly nosepiece to become distorted 5 ELECTRICAL CONNECTIONS LEFT FRONT ORANGE WHITE RIGHT BROWN GRAY e lee ue E Noise Filter RED To 12 Volt DC Power ORANGE Memory to Battery BLACK To Ground YELLOW Power Antenna LEFT GREEN BLUE ORANGE WHITE e REAR RIGHT ELECTRICAL CONNECTIONS Red Wire with fuse holder and noise filter Connect the red wire to a 12 volt power source that is switched on and off by the ignition key Most power sources can be located at the vehicles fuse block Use a test light or volt meter to select the correct connection point Oran
9. te and orange wire show This is for clarification of connection of the white and orange wire There is only one white wire and one orange wire provided on the harness SPECIFICATIONS FM Tuner Range secos ta ge OSE dene dede 87 5 107 9MHz Usable Sensitivity 17dBf 2uV 50dB Quieting Sensitivity 23 2dBf 4uV Signal to Noise 60dB Stereo Separation 1 35dB Capture Ratio sos o 8450 e ys 2 5dB Alternate Channel Selectivity 65dB AM Tuner xus 34 bean eu pha m eet uus E oai dad ius 530 1620kHz Sensitivity 20dB 10uV Signal to Noise Ratio 504 42dB Audio Section Maximum Power 2 x 9 Watts Continuous Average Power Output rms 10 THD 2 x 5 5 Watts Power Supply Voltage Negative Ground 14 4 Volts DC Dimensions CHASSIS ios e bus 178mm W x 44mm H x 130mm D Nose Piece 105mm W x 42mm H x 130mm D Weight sasa a AS eve Ee Ee eT 1 2kg Copyright 1998 Magnadyne Corp WARRANTY ONE 1 YEAR LIMITED WARRANTY Magnadyne Corporation or its authorized agents will within 1 year from the date of sale to you repair replace or refund the retail sales price of said product or any part thereof at the option of the Magnadyne Corporation or its authorized agents if sa
Download Pdf Manuals
Related Search