Home

Lowrance electronic EP-60R User's Manual

1. 4 Select EP 60R FueL FLow and press ENTER and a list of data options will appear 5 Highlight FUEL Usen and press ENTER 6 Press EXIT twice to return to the page display where Fuel Used data will be displayed on the screen To check fuel flow accuracy 1 After selecting Fuel Used as overlay data fill up your tank and press MENU twice Select NMEA 2000 or NETWORKING and press ENTER 2 Highlight FUEL MANAGEMENT and press ENTER Select TANK LOCATION and press ENTER 3 Select the tank location and press ENTER 40 4 Highlight F LL TANK and press ENTER The following confirmation message will appear Are you sure you wish to Fill Tank NOTE You must use the unit s Fill Tank command when filling your fuel tank to keep the fuel flow updated with correct information on the amount of fuel in the tank 5 Select YEs and press ENTER The following confirmation message will appear Do you wish to re calibrate the device 6 Highlight No and press ENTER 7 Take your vessel out on the water and burn at least five gallons of fuel Be sure you run only ONE engine the engine connected to your fuel flow 8 Fill up your tank again noting how much fuel you added to the tank Compare that number to the Fuel Used figure displayed on your display unit s screen If the amount of fuel you added to the tank and the fuel used figure are off by more than 3 percent we recommend the fuel flow be calibrated To calibrate a fue
2. Ethernet Diagnostics right The NMEA Diagnostics page displays information about the performance of the network bus keeping you updated on bus status mode errors and bus traffic The Ethernet Diagnostics page keeps you updated on the performance of an Ethernet connection if applicable supplying information ranging from IP Address to upload and download rates bytes per second To refresh either Diagnostics page highlight the Pine ALL Devices button at the bottom of the page and press ENT Engine amp Tank Configuration The Engine Tank configuration menu is located below the NMEA 2000 Devices list but will only be accessible if a fuel related sensor is on the network 34 Setting Engine Tank Configuration 1 Press MENU twice highlight NMEA 2000 or NETWORKING and press ENTER 2 The NMEA 2000 menu will appear with five options Bus Setup Fuel Management NMEA 2000 Alarms Waypoint Sharing and Backlight Synchronization Choose Bus Setup and press ENTER 3 Select ENGINE amp TANK ConFiG and press ENTER which will open the Engine amp Tank Configuration menu with the following configuration options 1 Engine 1 Tank 1 Engine 2 Tanks 2 Engines 1 Tank 2 Engines 2 Tanks 3 Engines l1 Tank 3 Engine 3 Tanks and Unconfigured Bus 4 Choose the configuration that matches the number of engines and tanks on your vessel and press ENTER 5 Highlight TANK SELEcT and press ENTER which will open the Tank Select menu 6 Sel
3. Secure the sensor hose assembly so the sensor remains in a vertical position with the flow direction up Clamp the hose on either side of the sensor to the hull or bulkhead to minimize vibration Route the sensor s cable connector to the T on the network backbone where you intend to attach it and plug it in The sensor is ready to use 4 Connecting to a NMEA 2000 Network A NMEA 2000 network is a communications link between two or more devices that transfer NMEA 2000 information LowranceNET is the NMEA 2000 networking system developed by Lowrance Electronics A NMEA 2000 network functions like the phone wiring in a house If for example you pick up a phone in the living room you will be able to hear the conversation someone is having on a phone in the bedroom In similar fashion a NMEA 2000 network allows multiple display units to receive data from a GPS antenna or multiple sonar units to receive messages sent by a temperature sensor A NMEA 2000 network gives you the flexibility to view information like engine diagnostics and fuel level data on digital gauges or display units located anywhere on your boat There are two types of LowranceNet red connectors the single T connector left and the double T connector right Network Backbone and Network Nodes A network bus backbone consists of network cabling terminators and T connectors Network nodes are made by fitting T shaped connectors into the backbone using the sockets on
4. 4 Select Location and press ENTER which will open the Location menu NOTE If you want to unconfigure your fuel flow select UNKNown from the Location menu 5 Highlight the desired location and press ENTER The following message will appear Are you sure you wish to change this device s configuration 6 Select YEs and press ENTER Press EXIT repeatedly to get back to the main display Unconfiguring an EP 60R Fuel Flow You can unconfigure a fuel flow by manually resetting its Location to default settings Unknown via the Location menu or you can use the Restore Defaults command To reset the fuel flow s device name refer to the previous segment covering Device Name The Device Name also may be reset by using the Restore Defaults command NOTE If you execute the Restore Defaults command you will have to re enter your engine tank configuration settings The Restore Defaults command is covered at the end of this section 38 Screen Sounds Transparency yi 1 Tank Operations ee aL Doel IE ETEEN Fuel Added 7 Route Planning e an E fem My Trails ees TH Center z 0 00 gal bez Cancel Navigation pat Tank ity 0 0 i Ea Sonar Setup le Tin sea Bs ga EAA I O ee MASS oie Add Fuel Fill Tank System Setup en ata h Networking J Bus Setup nese E 7 O ti Sun Moon Calculations Fuel Management sa Engine Uperations Trip Calculator NMEA 2000 Alarms Engine Sel
5. Pitot Speed and Gnd Spd Ground Speed A NMEA 2000 GPS module measures ground speed while a paddlewheel like the EP 70R Speed Sensor measures water speed 3 Select the desired speed source and press MENU which will take you back to the main display Reset Trip Fuel Used Rst trip f The LMF 200 uses fuel flow data to keep a running total of fuel used for a trip By using the Reset Trip command you can reset to zero the running total of fuel used on a trip 16 To Reset Trip Fuel Rst trip f 1 Press MENU use the UP and DOWN keys to select System SETUP and press MENU Highlight FUEL MNGR and press MENU 2 Select Rst TRIP F Reset Trip Fuel and press MENU The Select Engine menu will appear with up to four options Select the desired engine or All Engines and press MENU If you are using a single engine configuration you will not see the Select Engine menu 3 The following message will appear Hit Menu to Rst Trip F Press MENU which will reset the trip fuel used to zero Reset Seasonal Fuel Rst Seas The LMF 200 uses fuel flow data to keep a running total of fuel used for a season By using the Reset Seasonal command you can reset to zero the running total of fuel used for a season To reset seasonal fuel 1 Press MENU use the UP and DOWN keys to select System SETUP and press MENU Highlight FUEL MNGR and press MENU 2 Choose Rst Seas and press MENU If you have more than one engine the Select Engine menu
6. T connector and two 120 ohm terminators For complete instructions on setting up a new NMEA 2000 network or expanding an existing one see the other document packed with your EP 60R Fuel Flow Setup and Installation of NMEA 2000 Networks General Information part number 988 0154 173 If that document is unavailable it can be downloaded free from the Lowrance web site Other supplies are not included unless otherwise indicated Required supplies include cable ties or other fasteners to secure the hose and cable an inline fuel filter and any items needed to install it Two 1 hose clamps are included with the sensor We assume you already have a fuel line installed The EP 60R Fuel Flow was designed to fit a typical 3 8 SAE USCG Type A1 fuel hose If your engine has different diameter hoses or metal fuel lines a section of 3 8 fuel line must be installed between the sensor and the existing lines Recommended tools are a flathead screwdriver to tighten the clamps and a knife to cut the fuel hose If you need to route the sensor connector through a bulkhead you will need a drill and a 3 4 drill bit Installation Install one EP 60R sensor per engine If you have multiple tanks place the sensor after any Y or T in the line feeding the engine The sensor should be installed vertically as close as possible to the fuel tank in an area where vibration is minimized The housing has a molded in fuel flow direction arrow which should be po
7. use the UP and DOWN keys to select Customize and press ENTER The Position menu will appear with three options Top Data Center Data and Bottom Data 3 Highlight the desired data position and press ENTER 4 Select FueL FLow FUEL RANGE FUEL USED TRIP FUEL USED or SEASONAL FUEL Usep and press ENTER A menu will appear allowing you to display data from a single engine or from all engines on the vessel If you select FuEL RANGE or if your unit is configured for one engine you will be taken back to the Position menu 5 Select the desired engine or to display data from all engines highlight Vessel and press ENTER You will be taken back to the Position menu To display data in another data box repeat Steps 3 5 6 Press EXIT twice to return to the main display Reset Values By accessing Reset Values from the Fuel Flow menu you will be able to reset configuration and calibration settings for a particular fuel flow NOTE After using the Reset Values command you will have to re enter your engine tank configuration It however will not affect the configuration or calibration of other devices on the network To reset values 1 Press MENU use the UP and DOWN keys to select System SETUP and press ENTER 2 Highlight Bus Devices and press ENTER Select the fuel flow you want to reset and press ENTER 3 Choose RESET VALUES from the fuel flow menu and press ENTER The following message will appear Press Enter to Reset Device V
8. TANK CFG and press ENTER twice The following message will appear Press ENTER to reset Eng Tnk Cfg 3 Press MENU The Setup Menu will appear with Boat Setup highlighted Fuel Remaining Source The Fuel Remaining source function allows you to select the device used to measure the amount of fuel remaining in the tank It must be set to Fuel Flow Eng FFlow to work properly with the EP 60R The Fuel Remaining Source will be set to fluid level by default To change Fuel Remaining Source to fuel flow 1 Press MENU use the UP and DOWN keys to select System SETUP and press ENTER 2 Highlight Fue Setup and press ENTER 3 Select FUEL Rem Src Fuel Remaining Source and press ENTER 4 Highlight ENc FFLow Fuel Flow and press ENTER You are ready to configure your fuel flow sensor EP 60R Fuel Flow Configuration You can have up to three fuel flow sensors installed on your vessel one for each engine supported by the LMF 400 When accessing a fuel flow its menu will appear with the following options Change Engine for two or more engines only Fuel Warning Unset Engine Reset Values and Reset Calibration NOTE If after configuring unconfiguring or reconfiguring a fuel flow it is not shown on the Bus Devices list you will have to refresh the list To do this press MENU select System SETUP and press ENTER Highlight Bus Devices and press ENTER To configure a fuel flow When you configure a fuel flow you are linking the fuel
9. flow s location engine on the boat to its matching configuration name in the LMF 400 22 1 Press MENU use the UP and DOWN keys to select System SETUP and press ENTER 2 Highlight Bus Devices and press ENTER The Bus Devices list will appear nm a al a Eng Displayed A Eng Displayed J Pll til ape Bus nga TETN I N Message F PELL ae ADS 208 a E ial Searching A TT ecg Bus remp 2 DEVICES eee Reset Yalues o System Info 9 e W System Info a oe Bus Devices highlighted in the System Setup menu left Searching Bus Devices window center with Bus Devices list right 3 Select UnCrc F Flow and press ENTER The following message will appear Press Enter to Configure Fuel Flow Snsr 4 Press ENTER If your unit is configured for more than one tank the Select Engine menu will appear If your unit is set to a single tank configuration the Select Engine menu will not appear The fuel flow will automatically be given the configuration name Eng FF low 5 Select the desired engine and press ENTER You will be directed to the Bus Devices list Press EXIT repeatedly to return to the main display To unconfigure a fuel flow You will use the Unset Engine command to unconfigure a fuel flow To unset engine 1 Press MENU use the UP and DOWN keys to select System SETUP and press ENTER 2 Highlight Bus Devices and press ENTER to open the Bus Devices list 3 Select the desired fue
10. fuel flow and press ENTER The Device Configuration menu will appear 4 Highlight ADVANCED Options and press ENTER 5 Select RESTORE DEFAULTS and press ENTER The following message will appear Are you sure you wish to change this device s configuration 6 Highlight YEs and press ENTER Press EXIT repeatedly to return to the main display 44 Notes 45 Notes 46 LOWRANCE ELECTRONICS FULL ONE YEAR WARRANTY We our or us refers to LOWRANCE ELECTRONICS INC the manufacturer of this product You or your refers to the first person who purchases this product as a consumer item for personal family or household use We warrant this product against defects or malfunctions in materials and workmanship and against failure to conform to this product s written specifications all for one 1 year from the date of original purchase by you WE MAKE NO OTHER EXPRESS WARRANTY OR REPRESENTATION OF ANY KIND WHATSOEVER CONCERNING THIS PRODUCT Your remedies under this warranty will be available so long as you can show in a reasonable manner that any defect or malfunction in materials or workmanship or any non conformity with the product s written specifications occurred within one year from the date of your original purchase which must be substantiated by a dated sales receipt or sales slip Any such defect malfunction or non conformity which occurs within one year from your original purchase date will either be repaired without
11. the UP and DOWN keys to select System SETUP and press MENU 2 Highlight B Devices and press MENU Select the fuel flow you want to reset and press MENU 3 Select Rst CaL from the fuel flow menu and press MENU The following message will appear Hit Menu to Rst the Cal 4 Press MENU to set calibration back to factory default settings To recalibrate the fuel flow refer to the fuel flow calibration instructions in this section Refill Tank Refill T Since the EP 60R is not connected to the tank its fuel information is not automatically updated when the tank is filled up You must use the Refill Tank command to ensure the fuel information in the EP 60R stays consistent with the amount of fuel actually in the tank To refill tank 1 Press MENU use the UP and DOWN keys to select System SETUP and press MENU Highlight FuEL MNGR and press MENU 2 Select REFILL T and press MENU If your unit is configured for more than one tank the Select Tank menu will appear with up to three options If you are using a single tank configuration you will not see the Select Tank menu 3 Select the desired tank and press MENU The following message will appear Hit Menu if Tank filled up Press MENU and you will be taken you back to the main display Partial Fill Part Fill Since the EP 60R is not connected to the tank its fuel information is not automatically updated when fuel is added to the tank When you 15 add fuel to a tank witho
12. the sides and attaching any network device to the bottom of the T Staying with the previous phone wiring example T connectors on the backbone are the equivalent of phone jacks spread throughout a house To pick up a phone and be able to hear a conversation from another phone in the house both phones have to be connected to the main phone line In similar fashion only sensors and display units plugged into the NMEA network can share information The network backbone is like the phone wiring that runs throughout a home It connects the network nodes allowing them to communicate across the network Connections found in the middle of the bus could have T connectors or backbone network cable plugged into one or both sides Connections at the end of a network will have the backbone cable plugged into one side and a terminator plugged into the other as shown in the following figure Backbone cable to rest of bus Terminator at the end of the shasta eae backbone bus connector h able from di _ sensor or display unit Cap for unused connector NMEA 2000 network node located at the end of a NMEA 2000 backbone NOTE If you have a double T Connector on your network that is not attached to a device you must cap the unused connector with a NMEA 2000 cap This will protect the pin connectors from corrosion The NMEA 2000 cap looks like a terminator but has Cap stamped into the connector housing All T connectors on
13. will appear with up to four options 3 Select the desired engine or All Engines and press MENU The following message will appear Hit Menu to Rst USD S 3 Press MENU which will take you back to the main display Fuel Warning The Fuel Warning feature allows you to set a Low level or High level alarm for each fuel tank A pop up window will appear and an alarm will sound if the amount of fuel rises above High Level or falls below Low level the selected percentage of tank capacity To set a fuel warning 1 Press MENU select System SETUP and press MENU 2 Highlight Bus Devices and press MENU to display the Bus Devices list Select the desired Fuel Flow FFlow and press MENU The Configuration Options menu will appear 3 Select FUEL WARNING Fuel Wrng and press MENU 4 The Select Level menu will appear with two options High Level and Low Level 5 Select the desired level and press MENU The Level Percentage window will appear It will be set to Off by default 17 6 Use the UP and DOWN keys to input the desired percentage of tank capacity and press MENU Let the menus time out to return to the main display NOTE To turn off a fuel warning repeat Steps 1 4 then select Orr from the Level Percentage window mentioned in Step 5 Press MENU Repeat these steps for each warning you want to turn off Let the menus time out and you will be directed to the main display Engine Warnings Alarms The Engine Warnings
14. your network probably will be connected to a device If you want to add another node to a working network add another T connector T connectors may be purchased from LEI ordering information appears on the back page of this booklet If you are adding a Lowrance or LEI NMEA 2000 sensor it will come with a T connector Adding a Network Node You can add a node to any existing connection anywhere along the network backbone This connection could be between a T connector and a terminator between two T connectors between a T connector and a backbone extension cable or between two extension cables Wherever you want to add the new node separate the sockets of the existing connection and install the T connector between them If you want to add a node at the end of the backbone network bus remove the terminator from the last connector like the figure above Install the new T connector and attach the terminator to the side of the connector Use T connector or double T connector to add device to bus maintaining linear architecture mas Attach terminator at end of bus Backbone cable to rest of bus 4 Existing network node Devices connect to double T connector In this example a new device is added to the NMEA 2000 bus by installing a T connector between a T connector and a terminator at the end of the backbone network bus Additional Network Information For more information on creating or expanding a network refe
15. DD PAGE and press MENU 3 Highlight FUEL MANAGER Fuel Mngr and press MENU You will be taken back to the main display NOTE Make sure the Fuel Remaining Source has been set to Fuel Flow 13 To customize Fuel Manager page 1 With the Fuel Manager page displayed on the main display press MENU select Customize and press MENU 2 Highlight USD Fuel Used and press MENU If your unit is configured for more than one tank the Select Tank menu will appear If your engine tank configuration is set for one tank you will be directed to the main display 3 Select the desired option and press MENU You will be directed to the main display To check fuel flow accuracy 1 Make sure your Fuel Remaining Source has been set to Fuel Flow then fill up the fuel tank connected to the EP 60R Fuel Flow you want to calibrate Press MENU use the UP and DOWN keys to select SYSTEM SETuP and press MENU 2 Highlight FUEL MNGR and press MENU Select REFILL T and press MENU If your unit is configured for more than one tank the Select Tank menu will open Select the tank you refilled and press MENU If your unit is configured for one tank you will be taken directly to the Recalibration menu 3 The Recalibration ReCal menu will appear with two options Yes and No Select No and press MENU The following message will appear Hit Menu if Tank filled up 4 Press MENU which will direct you to the main display 5 Take your boat out but
16. Dual Digital Quad Digital and Fuel Manager pages Page Screen Rotation The Page Screen Rotation consists of multiple pages that have been set up for display Once pages have been added to the page screen rotation they can be set to scroll across the screen automatically or manually Use the ENTER and EXIT keys to manually scroll pages across the screen Pressing the ENTER key moves the scroll in one direction Pushing the EXIT key moves the scroll in the other direction You will use the Page Scrolling if you want pages to automatically scroll across the screen Refer to your LMF 400 manual for more information about Page Scrolling To add a page to the display 1 Press MENU use the UP and DOWN keys to select Paces and press ENTER A menu will pop up with four options Add Page Remove Page Page Scrolling and Pop Ups Setup 2 Select App PAGE and press ENTER 3 Highlight Single Digital Dual Digital Quad Digital or Fuel Manager and press ENTER The following message will appear Press Enter to add the selected page 4 Press ENTER which will take you back to the main display where the page you selected will be shown on the screen Customizing Pages The customizing pages feature allows you to choose what data will be displayed and how it will be displayed on select pages You can customize the Single Digital Dual Digital and Fuel Manager pages with fuel flow data which includes Fuel Rate fuel flow Fuel Used Fuel Range Tr
17. MENU twice select NMEA 2000 or NETWORKING and press ENTER A menu will appear with five options Bus Setup Fuel Management NMEA 2000 Alarms Waypoint Sharing and Backlight Synchronization 2 Highlight Bus Setup and press ENTER which will open the Bus Configuration menu A list of network devices will be at the top of the page 3 Select the fuel flow with the device name you want to reset and press ENTER The Device Configuration menu will appear with the Device Name dialog box highlighted 4 Press ENTER Depress the left arrow key until the device name disappears Press ENTER then press EXIT to return to the NMEA 2000 menu 37 5 Highlight the device and press ENTER The Device Configuration menu will open The device name will be reset to its default setting Press EXIT repeatedly to return to the main display Location The Location menu allows you to select a configuration name that matches the location of the engine connected to your fuel flow sensor To change fuel flow location 1 Press MENU twice select NMEA 2000 or NETWORKING and press ENTER A menu will appear with five options Bus Setup Fuel Management NMEA 2000 Alarms Waypoint Sharing and Backlight Synchronization 2 Highlight Bus Setup and press ENTER which will open the Bus Configuration menu A list of network devices will be at the top of the page 3 Select the fuel flow you want to configure and press ENTER The Device Configuration menu will appear
18. Pub 988 0154 432 L EP 60R Fuel Flow Electronic Sensor Installation Configuration and Calibration Instructions This document shows how to install an EP 60R Fuel Flow sensor and how to connect it to a NMEA 2000 network It also provides instructions on how to configure and calibrate your fuel flow sensor with Lowrance digital gauges LMF 200 amp LMF 400 and display units NMEA 2000 is the communication bus standard developed by the National Marine Electronics Association NMEA for use in boats Lowrance has introduced a line of products that can communicate over a NMEA 2000 network LowranceNet All Lowrance NMEA 2000 capable devices are either NMEA 2000 certified or certification is pending Caution Installing LowranceNET NMEA 2000 devices is significantly different from installing earlier Lowrance components without NMEA 2000 features You should read all of the installation instructions before proceeding You should decide where to install all components before drilling any holes in your vessel Fuel Flow module Bae NMEA 2000 red connector The EP 60R Fuel Flow sensor Some sonar or GPS display units may require a software upgrade to display NMEA 2000 data correctly For free software upgrades or additional information on the LowranceNet NMEA 2000 network system visit our web site www lowrance com The EP 60R consists of a red cable connector and the sensor module The sensor module contains a turbine to meas
19. alues 4 Press ENTER and you will be taken back to the Bus Devices list 32 Display Unit EP 60R Configuration amp Calibration All NMEA 2000 capable Lowrance sonar and sonar GPS combo display units can be used to configure and calibrate your EP 60R Fuel Flow sensor on a NMEA 2000 network LOWRANCE The LMS 525cDF is one of many Lowrance display units that may be used to configure an EP 60R Fuel Flow sensor NOTE Your unit may have NMEA 2000 menu or a Networking menu depending on your display unit s software version Both menus allow you to perform the same NMEA 2000 related functions Bus Setup Selecting Bus Setup from the NMEA 2000 or Networking menu will open the Bus Configuration menu giving you access to the Engine Tank Configuration menu and the NMEA 2000 Devices list The list located in the top half of the Bus Configuration menu shows all devices connected to the network The Engine Tank Configuration menu is located in the bottom half of the Bus Configuration menu The network devices list is located in the top half of the Bus Configuration menu 33 Screen Ez a Screen Sounds ee ig Sn s a Transparency Transparency oS Aerie Alarms S te Route Planning Route Planning My Trails My Trails i fr Cancel Navigation Billings oe Sonar Setup Cancel Navigation A at 7 GPS Setup Sonar Setup F Si System Setup La GPS Setup pis Ne oc E Bus Sern be Sun Moon Calculations Fuel Manageme
20. and press ENTER If your unit is configured for more than one tank the Select Tank menu will open Select the tank you refilled and press ENTER 11 The Recalibration menu will appear with two options Yes and No Select YES and press ENTER 12 The Filled Fuel Quantity window will appear Use the UP and DOWN keys to input the amount of fuel you added to the tank and press ENTER 13 Repeat these steps for each fuel flow you want to calibrate NOTE It is a good idea to periodically check the calibration of a fuel flow Reset Calibration The Reset Calibration command allows you to set fuel flow calibration to factory defaults To reset calibration 1 Press MENU use the UP and DOWN keys to select System SETUP and press ENTER 26 2 Highlight Bus Devices and press ENTER Highlight the fuel flow you want to reset and press ENTER 3 Select RESET CaL from the fuel flow menu and press ENTER The following message will appear Press Enter to reset the Calibration 4 Press ENTER to set calibration back to default settings To recalibrate the fuel flow follow the fuel flow calibration steps in this section Refill Tank Since the EP 60R is not connected to the tank its fuel information is not automatically updated when the tank is filled up You must use the Refill Tank command to ensure the fuel information in the EP 60R stays consistent with the amount of fuel actually in the tank To refill tank 1 Press MENU use th
21. ar and GPS products manufactured by Lowrance Electronics and Eagle Electronics To order Lowrance or Eagle accessories please contact 1 Your local marine dealer or consumer electronics store To locate a Lowrance dealer visit the web site www lowrance com and look for the Dealer Locator To locate an Eagle dealer visit the web site www eaglesonar com and look for the Dealer Locator Or consult your telephone directory for listings 2 U S customers LEI Extras Inc PO Box 129 Catoosa OK 74015 0129 Call toll free in the U S 800 324 0045 8 a m to 5 p m Central Standard Time M F or visit our web site www lei extras com 3 Canadian customers Lowrance Eagle Canada 919 Matheson Blvd E Mississauga Ontario L4W2R7 or fax 905 629 3118 Call toll free in Canada 800 661 3983 or dial 905 629 1614 not toll free 8 a m to 5 p m Eastern Standard Time M F ACCESSORIES For Lowrance and Eagle Products Pub 988 0154 432 Copyright 2007 All Rights Reserved Printed in USA 091407 Lowrance Electronics Inc 48
22. ation 35 menu To configure or calibrate most devices you will select it on the NMEA 2000 Devices list and press ENTER This will open its Device Configuration menu NMEA 2000 Devices 1 Ep 10 Fuel Flow 2 EP 15 Fuel Level PORT 3 EP 35 Live Well Temp 4 Internal GPS Non Network 5 LGC 2000 0 Engine amp Tank Config 1 Engine s 2 Tank s Set Configuration Tank Select Tank Size Pot ssti it t SLO A Bus Configuration menu with five items displayed on the NMEA 2000 Devices list Engine Tank Configuration and Tank Select menus are at the bottom of the screen Device Configuration Menu When a device is selected from the network devices list on the Bus Configuration menu its Device Configuration menu will appear Device configuration menus vary among devices Available functions on device configuration menus allow you to change device names tank sizes fluid types and provide access to the Advanced Options menu We will cover configuration and calibration later in this section Device Information and Device Data The Device information panel located to the left of the Device Configuration menu displays information on the selected device that includes software version model address serial number instance and current status Device Data is shown in the Device Data window at the bottom of the device configuration menu The information displayed in the Device Data window will vary among d
23. be taken back to the Position menu 5 Select the desired engine or to display data from all engines highlight Vessel and press ENTER You will be taken back to the Position menu To display data in the other data box repeat Steps 3 5 6 Press EXIT twice to return to the main display To customize Quad Digital page 1 After the Quad Digital page has been added to the page screen rotation use the ENTER and EXIT keys to display it on the main screen 2 Press MENU use the UP and DOWN keys to select Customize and press ENTER The Position menu will appear with four options Data Box 1 Data Box 2 Data Box 3 and Data Box 4 3 Highlight the desired data position and press ENTER 4 Select FueL FLow FUEL RANGE FUEL USED TRIP FUEL USED or SEASONAL FUEL Usep and press ENTER A menu will appear allowing you to display 31 data from a single engine or from all engines on the vessel If you select FueL RANGE or if your unit is configured for one engine you will be taken back to the Position menu 5 Select the desired engine or to display data from all engines highlight Vessel and press ENTER You will be taken back to the Position menu To display data in another data box repeat Steps 3 5 6 Press EXIT twice to return to the main display To customize Fuel Manager page 1 After the Fuel Manager page has been added to the page screen rotation use the ENTER and EXIT keys to display it on the main screen 2 Press MENU
24. ch fuel flow has an internal menu with the following options Unset Engine Change Engine multiple engines only Fuel Warning Reset and Reset Calibration To configure a fuel flow 1 Press MENU use the UP and DOWN keys to select System SETUP and press MENU 2 Highlight B Devices and press MENU After a few moments the Bus Devices list will appear 10 3 Select UNCFc FF and press MENU The following message will appear Hit Menu to Cfg Flow Sns Press MENU and the Configuration options menu will appear NOTE If your unit is set to a single engine configuration the Configuration Options menu will not appear when you are configuring a fuel flow The fuel flow will automatically be configured as Eng FF low 4 Select the desired option and press MENU You will be directed to the Bus Devices list Configure remaining fuel flows by following the steps above To unconfigure a fuel flow You will use the Unset Engine command when you want to unconfigure a fuel flow To unset engine 1 Press MENU use the UP and DOWN keys to select System SETUP and press MENU 2 Highlight B Devices and press MENU After a few moments the Bus Devices list will appear 3 Select the fuel flow you want to unconfigure and press MENU 4 Highlight UNseET ENGINE and press MENU which will launch the following message Hit Menu to Unset Dev Name 5 Press MENU and you will be taken back to the Bus Devices list The newly unconfigured fuel f
25. charge or be replaced with a new product identical or reasonably equivalent to this product at our option within a reasonable time after our receipt of the product If such defect malfunction or non conformity remains after a reasonable number of attempts to repair by us you may elect to obtain without charge a replacement of the product or a refund for the product THIS REPAIR OR REPLACEMENT OR REFUND AS JUST DESCRIBED IS THE EXCLUSIVE REMEDY AVAILABLE TO YOU AGAINST US FOR ANY DEFECT MALFUNCTION OR NON CONFORMITY CONCERNING THE PRODUCT OR FOR ANY LOSS OR DAMAGE RESULTING FROM ANY OTHER CAUSE WHATSOEVER WE WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO ANYONE FOR ANY SPECIAL CONSEQUENTIAL INCIDENTAL OR OTHER INDIRECT DAMAGE OF ANY KIND Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you This warranty does NOT apply in the following circumstances 1 when the product has been serviced or repaired by anyone other than us 2 when the product has been connected installed combined altered adjusted or handled in a manner other than according to the instructions furnished with the product 3 when any serial number has been effaced altered or removed or 4 when any defect problem loss or damage has resulted from any accident misuse negligence or carelessness or from any failure to provide reasonable and necessary maintenance
26. data on your unit s main display To add overlay data from the EP 60R 1 Press MENU highlight OverLay DATA and press ENTER 2 Select PRESS ENT To ADD and press ENTER 3 Highlight NMEA 2000 and press ENTER A list of devices on the network will appear 4 Select the desired fuel flow and press ENTER Fuel Rate Fuel Used Trip Fuel Used and Seasonal Fuel Used categories will appear 5 Highlight the data you want to display and press ENTER which will place a checkmark in its enabled box It now will be shown as overlay data on your unit s main display 6 Repeat step 5 to display another data category or press EXIT repeatedly to return to the main display NMEA 2000 Alarms The NMEA 2000 Alarms menu allows you to set Full and Empty fuel alarms for a number of NMEA 2000 devices The alarms may be set to a percentage 0 100 of tank capacity To turn on off NMEA 2000 Alarm 1 Press MENU twice select NMEA 2000 or NETWORKING and press ENTER 2 Highlight NMEA 2000 ALaArms and press ENTER 3 Highlight Flup LeveL Device and press ENTER Select the desired fuel flow and press ENTER 4 Highlight the ENABLED box next to the desired alarm Full Alarm or Empty Alarm and press ENTER to turn on the alarm When the alarm is on an X will be placed in the Enabled Box 5 To set the alarm percentage highlight PERCENT and press ENT 6 Use the arrow keys to input the desired percentage and press ENTER Repeat Steps 3 4 to s
27. e UP and DOWN keys to select System SETUP and press ENTER 2 Highlight Fue Setup and press ENTER 3 Select REFILL TANK and press ENTER The select Tank menu will appear with up to three options Select the tank you refilled and press ENTER If you have one tank you will be taken directly to the recalibration window mentioned in step 4 4 A recalibration window will appear with two options Yes and No Select No and press ENTER The following message will appear Press Enter after refilling the fuel tank 5 Press ENTER You will be directed back to the main display Partial Fill Since the EP 60R is not connected to the tank its fuel information is not automatically updated when fuel is added to the tank When you add fuel to a tank without completely filling it up you must use the Partial Fill command This will ensure the fuel information in the EP 60R stays consistent with the amount of fuel actually in the tank To use Partial Fill 1 Press MENU use the UP and DOWN keys to select System SETUP and press ENTER Highlight Fue Setup and press ENTER 2 Select PARTIAL FILL and press ENTER The Select Tank menu will appear with up to three options If you have one tank you will be taken directly to the Adding Fuel window 3 Select the desired tank and press ENTER The Adding Fuel window will appear Zi NOTE When using the Partial Fill command you will only be able to input into the gauge an amount of fuel less or e
28. ect Timers X Waypoint Sharing AIl Engines amp Browse Files X Backlight Synchronization All Engines Edmond H PA Calibration Const 0 00 C Reset Calibration Reset Trip ie Reset Seasonal a I Fuel Management highlighted on Networking menu left Fuel Management menu right 36 08 971 H 95 50579 Fuel Management Menu The Fuel Management menu gives you access to the following options Tank Location Fuel Added Add Fuel Fill Tank Engine Select Reset Calibration Reset Trip and Reset Seasonal The menu is divided into two parts Tank Operations and Engine Operations You will calibrate your fuel flow from Tank Operations section of the Fuel Management menu Engine Operations are located in the lower half of the menu Tank Operations The top half of the Fuel Management menu covers Tank Operations which include Tank Location Fuel Added Add Fuel and Fill Tank Adding Fuel to Tank Tank Location Fuel Added and Add Fuel commands work together to keep NMEA 2000 fuel data consistent with the actual amount of fuel added to the fuel tank s 1 Press MENU twice select NMEA 2000 or NETWORKING and press ENTER 2 A menu will appear with five options Bus Setup Fuel Management NMEA 2000 Alarms Waypoint Sharing and Backlight Synchronization Select FUEL MANAGEMENT and press ENTER 3 Highlight Tank Location and press ENTER The Tank Location menu wil
29. ect the tank you want to set up and press ENTER Highlight the Tank Size icant box and os ENTER a Pewee ele Diagnostics NMEA 2000 Devices 1 EP 10 Fuel Flow PORT EP 15 Oil Level Unconfigured 3 EP 25 Speed EP 35 Live Well Temp 5 EP 35 Water Temp 6 Internal GPS Non Network 7 LGC 2000 0 7 LGC 2000 0 1 Engine s 1 Tank s amp 1 Engine s 2 Tank s 2 Engine s 1 Tank s 2 Engine s 2 Tank s 3 Engine s 1 Tank s Engine amp Tank Config a Engine amp Tank Config 1 Engine s 1 Tank s gt Set Configuration APTIT Set Configuration f Engine s 1 Tank s Set Configuration Tank Select Tank Size Tank Size Tank Select Center 380 0 gal StarBoard X 40 0 gal StarBoard 0610 0 gal 1 Engine 1Tank highlighted on Engine and Tank Configuration menu left Starboard highlighted on Tank Select menu center Tank Size set to 40 gallons right 7 Input the capacity gallons of the tank you chose from the Tank Select menu and press ENTER 8 Repeat Steps 5 7 for each remaining tank 9 When all tanks have been configured press the SET CONFIGURATION button The following confirmation message will appear Are you sure you wish to change the bus configuration Choose Yes and press ENTER Press EXIT to return to the main display NMEA 2000 Devices List Devices connected to your NMEA 2000 network will be listed on the NMEA 2000 Devices list located at the top of the Bus Configur
30. et the other alarm 7 Highlight SET CONFIGURATION and press ENTER to finalize alarm settings Press EXIT repeatedly to get back to the main display NOTE To turn off uncheck an alarm select its ENABLED Box and press ENTER Highlight the SET CoNFiGURATION button and press ENTER 43 Alarm Status Tab The Alarm Status tab is the second tab at the top of the NMEA 2000 Alarms page When an alarm has been set for a device the alarm and its current status will be shown on the Alarm Status window To view Alarm Status 1 Press MENU twice select NMEA 2000 or NETWORKING and press ENTER 2 Select NMEA 2000 ALARms and press ENTER 3 Highlight the Alarm Status tab 4 Press EXIT repeatedly to return to the main display Restore Defaults The Restore Defaults command allows you to reset EP 60R Fuel Flow settings to factory defaults NOTE After using the Restore Defaults command you will have to re enter your engine tank configuration It however will not affect the configuration or calibration of other devices on the network To use the Restore Defaults command 1 Press MENU twice select NMEA 2000 or NETWORKING and press ENTER A menu will appear with five options Bus Setup Fuel Management NMEA 2000 Alarms Waypoint Sharing and Backlight Synchronization 2 Highlight Bus Setup and press ENTER which will open the Bus Configuration menu A list of network devices will be at the top of the page 3 Select the desired
31. evices If for example you are viewing the device configuration menu for an EP 65R Fluid Level the device data window will include tank size and the amount of fuel left in the tank The Device Data for an EP 60R Fuel Flow includes Fuel Rate amount of fuel burned per hour Fuel Used Trip Fuel Used and Seasonal Fuel Used 36 EP 60R Fuel Flow Configuration When configuring your fuel flow you will open its Device Configuration menu where you can access the Location and Advanced Options menu You can also change your fuel flow s device name Device Name You can change how your fuel flow will be displayed on your unit s NMEA 2000 Devices list by inputting a customized device name in the Device Name dialog box NOTE Changing the Device Name only will affect the way the EP 60R is shown on your display unit The customized device name will not be seen by other devices or display units on the NMEA 2000 network To change Device Name 1 Press MENU twice select NMEA 2000 or NETWoRKING and press ENTER 2 Highlight Bus Setup and press ENTER Select the desired fuel flow from the Bus Devices list and press ENTER 3 Device Name will be highlighted Press ENTER to access the Device Name dialog box 4 Use the UP and DOWN keys to change the Device Name When you have finished inputting the desired Device Name press ENTER Press EXIT repeatedly to return to the main display To reset device name to default setting 1 Press
32. feature allows you to set an alarm for one or more engines which will alert you to several engine issues including overheating and low oil pressure To set Engine Warnings 1 Press MENU use the UP and DOWN keys to select System SETUP and press MENU 2 Highlight ENGINE WARNINGS and press MENU The Engine Warnings menu will appear with up to five options including Off and All Engines The default setting is All Engines If you have a single engine configuration the only options on the Engine Warning menu will be On and Off NOTE If you choose All Engines the alarm will be shown for each alarm engine alarm If a single engine is selected the gauge will only show warnings from the selected engine To turn off all engine warnings highlight OFF and press MENU If you turn off engine alarms no alarms will be shown for any of the engines 3 Highlight the desired option and press MENU You will be taken back to the main display Displaying data from fuel flow You can display fuel flow data on the Single Digital Dual Digital and Fuel Manager pages Page Screen Rotation The Page Screen Rotation consists of multiple pages that have been set for display Once pages have been added to the page screen rotation they can be set to scroll across the screen automatically or manually Press the UP and DOWN keys to manually scroll pages across the screen Pressing the UP key moves the scroll in one direction Pushing the DOWN key m
33. fuel flow is not shown refresh the Bus Devices list Reset The Reset command in the Fuel Flow level menu will clear the sensor s configuration and calibration settings NOTE After using the Reset command you will have to re enter your engine tank configuration It however will not affect the configuration or calibration of other devices on the network To reset fuel flow settings 1 Press MENU use the UP and DOWN keys to select System SETUP and press MENU 2 Highlight B Devices and press MENU After a few moments the Bus Devices list will appear 3 Select the desired fuel flow and press MENU Highlight RESET press MENU and the following message will appear Hit Menu to Rst Values 4 Press MENU to reset fuel flow values to default settings EP 60R Fuel Flow Calibration The factory calibration settings for the EP 60R Fuel Flow should be within 3 percent so calibration will not be necessary in most cases NOTE Make sure the fuel flow has been set as the Fuel Remaining Source otherwise you will not be able to calibrate the fuel flow Fuel Flow Accuracy To check fuel flow accuracy you must add the Fuel Manager page to the page screen rotation and then customize it with Fuel Used data To add Fuel Manager page to the display 1 Press MENU use the UP and DOWN keys to select PAGES and press MENU which will open the Pages menu with the following options Add Page Rem Page Autoscroll and Set Pop up 2 Select A
34. if your unit is configured for one engine you will be taken back to the main display 4 Select the desired engine or to display data from all engines highlight Vessel and press MENU You will be taken back to the main display where the data you selected will be shown To customize Dual Digital page 1 After the Dual Digital page has been added to the page screen rotation use the UP and DOWN keys to display it on the screen 2 Press MENU select Customize and press MENU The Position menu will appear with two options Top Data and Bottom Data 3 Select the desired data position and press MENU 4 Highlight FueL Flow Fut F FueL Usep USD FUEL RANGE RNG TRIP FueL Usep USD Tp or SEASONAL FUEL Usep USD SE and press MENU A 19 menu will appear allowing you to display data from a single engine or show data from all engines If you select FUEL RANGE RNG or if your unit is configured for one engine you will be taken back to the main display 5 Select the desired engine or to display data from all engines highlight Vessel and press MENU You will be taken back to the main display where the data you selected will be shown Repeat these steps to customize the other data position To customize Fuel Manager page 1 After the Fuel Manager page has been added to the page screen rotation use the UP and DOWN keys to display it on the screen 2 Press MENU select Customize and press MENU 3 Highlight FueL Flow F
35. in accordance with the instructions of the owner s manual for the product We reserve the right to make changes or improvements in our products from time to time without incurring the obligation to install such improvements or changes on equipment or items previously manufactured This warranty gives you specific legal rights and you may also have other rights which may vary from state to state REMINDER You must retain the sales slip or sales receipt proving the date of your original purchase in case warranty service is ever required LOWRANCE ELECTRONICS 12000 E SKELLY DRIVE TULSA OK 74128 800 324 1356 47 How to Obtain Service in the USA Contact the Factory Customer Service Department Call toll free For Lowrance 800 324 1356 For Eagle 800 324 1354 8 a m to 5 p m Central Standard Time M F Lowrance Electronics and Eagle Electronics may find it necessary to change or end their shipping policies regulations and special offers at any time They reserve the right to do so without notice In Canada Contact the Factory Customer Service Department Call toll free 800 661 3983 905 629 1614 not toll free 8 a m to 5 p m Eastern Standard Time M F outside Canada and the USA Contact the dealer in the country where you purchased your unit To locate a dealer near you see the instructions in paragraph number 1 below Accessory Ordering Information LEI Extras Inc is the accessory source for son
36. inting up Mount the sensor above the tank s maximum fuel level to avoid accidental fuel leakage in case the sensor becomes disconnected Caution Gasoline is extremely flammable If possible drain the fuel line before you start or shut any flow valves located at the tank Keep sparks and flame away from the work area After installation remember to clean up any spilled fuel 3 Cut the fuel hose where you intend to install the EP 60R sensor Slide a clamp over the hose coming from the tank then push the hose onto the bottom inlet hose barb Seat the hose flush against the sensor housing then tighten the hose clamp Attach the hose leading to the engine on the top outlet barb in the same way To engine aa ee ee ds Push the fuel line onto the hose barb then tighten the hose clamp Orient the sensor vertically with the flow arrow pointing up NOTE You must install an in line fuel filter between the tank and the EP 60R sensor This will prevent a malfunction caused by contaminated fuel Debris in unfiltered fuel can clog the sensor s turbine and result in rough performance or engine shut down As with any fuel system we recommend you always carry onboard a spare fuel filter and an in line 3 8 splice barb This allows you to remove a clogged EP 60R fuel sensor or fuel filter and restore engine operation if the fuel filter fails We strongly recommend that you inspect your entire fuel system at regular intervals
37. ip Fuel Used and Seasonal Fuel Used 30 To customize Single Digital page 1 After the Single Digital page has been added to the page screen rotation use the ENTER and EXIT keys to display it on the main screen 2 Press MENU use the UP and DOWN keys to select CustomizE and press ENTER The data menu will appear 3 Highlight Fuel Flow Fuel Range Fuel Used Trip Fuel Used or Seasonal Fuel and press ENTER A menu will appear allowing you to display data from a single engine or from all engines If you select FUEL RANGE or if your unit is configured for one engine you will be directed back to the main display 4 Select the desired engine or to display data from all engines highlight Vessel and press ENTER You will be taken back to the main display where the data you selected will be shown To customize Dual Digital page 1 After the Dual Digital page has been added to the page screen rotation use the ENTER and EXIT keys to display it on the main screen 2 Press MENU use the UP and DOWN keys to select Customize and press ENTER The Position menu will appear with two options Top Data and Bottom Data 3 Highlight the desired data position and press ENTER 4 Select FueL FLow FUEL RANGE FUEL UseD TRIP FUEL USED or SEASONAL FUEL and press ENTER A menu will appear allowing you to display data from a single engine or from all engines If you select FUEL RANGE RNG or if your unit is configured for one engine you will
38. ired tank option and press ENTER Press EXIT twice to return to the main display where Fuel Used data will be displayed on the Fuel Manager page To check fuel flow accuracy 1 Make sure the Fuel Remaining Source has been set to Fuel Flow then fill up the tank connected to the fuel flow you want to calibrate 25 2 Press MENU use the UP and DOWN keys to select System SETUP and press ENTER 3 Highlight Fue Setup and press ENTER 4 Select REFILL TANK and press ENTER If your unit is configured for more than one tank the Select Tank menu will open 5 Select the tank you refilled and press ENTER A Recalibration window ReCalibrate will appear with two options Yes and No Select No and press ENTER The following message will appear Press Enter after refilling the fuel tank Press ENTER 6 Take your boat out but run only ONE engine the engine connected to the fuel flow Burn at least 5 gallons of fuel then fill up the tank again noting how much fuel was added to the tank Check the Fuel Manager page for the fuel used figure calculated by the LMF 400 7 Compare the amount of fuel added when you filled up the tank with the LMF 400 Fuel Used figure If the difference between these two numbers is greater than 3 percent you need to calibrate the unit To calibrate a fuel flow 8 Press MENU use the UP and DOWN keys to select System SETUP and press ENTER 9 Highlight Fue Setup and press ENTER 10 Select REFILL TANK
39. ist you will have to refresh the list Let the Bus Devices list time out then access it again 6 Highlight Stsp FFLow and press MENU Select CHANGE ENGINE and press MENU which will open the Select Engine menu with up to three options Port Cen Stbd 7 Highlight Port and press MENU 8 You will be taken back to the Bus Devices list where the fuel flow you selected formerly Stbd FFlow will now be shown as Port FFlow If the newly configured fuel flow is not shown refresh the Bus Devices list 9 Now select UNCFc FFLow and press MENU The following message will appear Hit Menu to Cfg Flow Sns 10 Press MENU which will open the Select Engine menu Highlight Starboard and press MENU You will be directed to the Bus Devices list where the fuel flow now will be displayed as Stbd FFlow If the newly configured fuel flow is not shown refresh the Bus Devices list If configuration name available 1 Press MENU use the UP and DOWN keys to select System SETUP and press MENU 2 Highlight B Devices and press MENU After a few moments the Bus Devices list will appear 3 Highlight Port FFLow and press MENU Select CHANGE ENGINE and press MENU which will open the Select Engine menu with up to three options Port Cen Stbd 4 Highlight STARBOARD and press MENU 12 5 You will be taken back to the Bus Devices list where the fuel flow you selected formerly Port FFlow will be listed as Stbd FFlow If the newly configured
40. l appear 4 Select the tank you added fuel to and press ENTER 5 Follow the steps below that apply to your tank 39 If you filled up the tank A Press the FILL TANK button and press ENTER The following message will appear Are you sure you wish to Fill Tank Press ENTER Another message will appear Do you wish to re calibrate the device Highlight No and press ENTER If you did not fill up the tank B Highlight FueL AppED and press ENTER to access the FUEL ADDED dialog box Use 4 gt to input the amount of fuel added to the tank and press ENTER Select the App Fue button and press ENTER The following message will appear Are you sure you wish to Add Fuel Highlight Yes and press ENTER 6 Press EXIT repeatedly to get back to the main display EP 60R Fuel Flow Calibration The default calibration for the EP 60R Fuel Flow is adequate in most cases but if Fuel Used readings are off by more than 3 percent calibration is recommended Fuel Flow Accuracy To check fuel flow accuracy you must overlay Fuel Used data on your display to be able to check the accuracy of fuel information coming from the fuel flow To overlay Fuel Used data on your screen 1 Press MENU select OVERLAY DATA and press ENTER 2 If you currently have any overlay data on your screen it will be listed here Select ENTER TO ADD and press ENTER 3 Highlight NMEA 2000 or NETWORKING and press ENTER which will open the NMEA 2000 Devices list
41. l flow 9 Fill up your tank Press MENU twice select NMEA 2000 or NETWORKING and press ENTER 10 Highlight FUEL MANAGEMENT and press ENTER Highlight TANK LOCATION and press ENTER 11 Select the desired tank location and press ENTER 12 Highlight Fitt TANK and press ENTER The following message will appear Are you sure you wish to Fill Tank Select Yes and press ENTER 13 The following message will appear Do you wish to re calibrate the device Select YES and press ENTER 14 Repeat these steps for each EP 60R Fuel Flow you want to calibrate Engine Operations The lower half of the Fuel Management menu covers Engine Operations which include Engine Select Reset Calibration Reset Trip and Reset Seasonal Engine Select Engine Select allows you to choose the desired engine when resetting calibration resetting trip fuel and resetting seasonal fuel 41 To Reset Calibration Choosing the Reset Calibration command will switch fuel flow calibration settings back to factory defaults 1 Press MENU twice select NMEA 2000 or NETWORKING and press ENTER 2 Highlight FUEL MANAGEMENT and press ENTER 3 Highlight to ENGINE SELECT and press ENTER Select the desired engine and press ENTER 4 Highlight RESET CALIBRATION and press ENTER The following confirmation message will appear Are you sure you wish to Reset Calibration Select Yes and press ENTER Calibration settings for the selected fuel have been returned to fact
42. l flow and press ENTER The Fuel Flow menu will appear Select Unset ENGINE and press ENTER The following message will appear Press Enter to UnConfig Device Name 4 Press ENTER and you will be directed back to the Bus Devices list where the fuel flow you unconfigured will be shown as UnCfg F Flow To reconfigure a fuel flow You will use the Change Engine command to reconfigure a Fuel Flow Change Engine however will only appear on the LMF 400 menu if a multiple engine setting was chosen during Boat Setup If all the fuel flows on your vessel are configured you will have to unconfigure a fuel 23 flow to free up its configuration name If all three fuel flows are configured which means there is no configuration name available follow the first set of instructions If the desired configuration name is available follow the second set of instructions Change Engine active only with multiple engine setting The steps below show how to switch the configuration name of a fuel flow from Port engine to Starboard engine If all fuel flows configured Configuration name unavailable 1 Press MENU use the UP and DOWN keys to select System SETUP and press ENTER 2 Highlight Bus Devices and press ENTER The Bus Devices list will appear 3 Select the Port fuel flow and press ENTER Highlight UNset ENGINE and press ENTER The following message will appear Press Enter to UnConfig Device Name 4 Press ENTER You will be taken back to the B
43. low will be displayed as UNCFc FF To reconfigure a fuel flow You will use the Change Engine command to reconfigure a Fuel Flow Change Engine however will only appear on your LMF 200 menu if you have more than one engine If you want to reconfigure a fuel flow but all the fuel flows on your vessel are configured you first will have to unconfigure a fuel flow to free up its configuration name If all three fuel flows are configured which means there is no name configuration available follow the first set of instructions If the desired configuration name is available follow the second set of instructions Change Engine Active only with multiple engine setting The Change Engine command allows you to change the configuration name of a fuel flow The steps below show how to switch the configuration name of a fuel flow from Port to Starboard 11 If all fuel flows configured Configuration name unavailable 1 Press MENU use the UP and DOWN keys to select System SETUP and press MENU 2 Highlight B Devices and press MENU The Bus Devices list will appear 3 Select the Port FFlow and press MENU 4 Highlight UNseT ENGINE and press MENU The following message will appear Hit Menu to Unset Dev Name 5 Press MENU and you will be taken back to the Bus Devices menu where fuel flow formerly Port FFlow now will be displayed as UnCfg FF low Remember If the fuel flow you just unconfigured is not shown on the Bus Devices the l
44. message will appear Press Enter to reset Trip Fuel 4 Press ENTER which will reset the trip fuel to zero and take you back to the main display Reset Seasonal The LMF 400 keeps a running total of fuel used for a season By using the Reset Seasonal command you can reset to zero the running total of fuel used for a season 28 To reset seasonal fuel 1 Press MENU select System SETUP and press ENTER 2 Highlight FueL Setup and press ENTER 3 Select RESET SEASONAL and press ENTER The Select Engine menu will appear with up to four options If you have one engine the reset seasonal fuel message Step 4 will appear 4 Select the desired engine or All Engines and press ENTER The following message will appear Press Enter to reset Seasonal Fuel 5 Press ENTER to reset seasonal fuel You will be taken back to the main display Fuel Warning The Fuel Warning feature allows you to set a Low level or High level alarm for each fuel tank A pop up window will appear and an alarm will sound if the amount of fuel rises above High Level or falls below Low level the selected percentage of tank capacity To set a fuel warning 1 Press MENU highlight System Setup and press ENTER 2 Select Bus Devices and press ENTER Highlight FueL Flow and press ENTER The Fuel Flow menu will appear Select FueL Warninec Fuel Wrng and press ENTER 3 The Select Level menu will appear with two options High Level and Low Level 4 Highligh
45. nt System Setup Trip Calculator NMEA 2000 Alarms NMEA 2000 se Timers X Waypoint Sharing Sun Moon Cal Fuel Management Browse Files Backlight Synchronization Trip Calculator NMEA 2000 Alarms IE a Timers r Waypoint Sharing BS Browse Files Backlight Synchronization 135th E Lo _Venezeula Ta 2 4000 mi Bus Setup highlighted on the NMEA 2000 menu left Bus Setup selected on Networking menu right i The Engine Tank Configuration and Tank Select menus as well as the Tank Size dialog box are located on the bottom half of the Bus Configuration menu The Set Configuration button positioned next to the engine tank configuration menu allows you to finalize a e Con ao NMEA 2000 Bus Configuration NMEA Diagnostics Controller Status Controller Status Mode Normal IP Addr 0 0 0 0 Status 0x00 MAC 00 00 00 00 00 00 EP 25 Speed i re EP 35 Heating System Temp Total Per Second es aise oone 5 EP 35 Heating System Temp Rx Errors 0 0 Tx 0 bytes 0 bytes sec 6 Internal GPS Non Network K im Tear 7 LGC 2000 0 Tx Errors 0 0 I Bus Traffic Open Ports Total Per Second Rx Messages 0 0 Tx Messages 0 0 Engine amp Tank Config f Engine s 1 Tank s Set Configuration J OH Tank Select Tank Size Center 120 0 gal Ping All Devices Ping All Devices Bus Configuration menu left NMEA Diagnostics page center
46. ory defaults To Reset Trip The Reset Trip function allows you to reset to zero the running total of fuel used on a particular trip 1 Press MENU twice select NMEA 2000 or NETWORKING and press ENTER 2 Highlight FUEL MANAGEMENT and press ENTER The Fuel Management menu will appear 3 To reset trip fuel used for a particular engine highlight ENGINE SELECT and press ENTER Select the desired engine or All Engines and press ENTER 4 Highlight REset Trip and press ENTER The following confirmation message will appear Are you sure you wish to Reset Trip 5 Highlight Yes and press ENTER The Trip Fuel Used figure has been reset to zero To Reset Seasonal Your unit can track fuel usage not only for trips but also for entire seasons The reset seasonal command allows you to reset to zero the running total of fuel used during a season 1 Press MENU twice select NMEA 2000 or NETWORKING and press ENTER 2 Highlight FUEL MANAGEMENT and press ENTER 3 To reset seasonal trip fuel used for a particular engine highlight ENGINE SELECT and press ENTER Select the desired engine or All Engines and press ENTER 4 Highlight Reser SEASONAL and press ENTER The following confirmation message will appear Are you sure you wish to Reset Seasonal 5 Highlight Yes and press ENTER The Seasonal Fuel Used figure has been reset to zero 42 Displaying data from fuel flow The Overlay Data function will be used to show EP 60R Fuel Flow
47. oves the scroll in the other direction You can use the 18 Autoscroll feature if you want the pages to automatically scroll across the screen Refer to your LMF 200 manual for more information about Autoscroll Adding a page 1 Press MENU use the UP and DOWN keys to select Paces and press MENU which will open the Pages menu with the following options Add Page Rem Page Autoscroll and Set Pop up 2 Highlight App PAGE and press MENU 3 Select Single Digital Dual Digital or the Fuel Manager page and press MENU You will be taken back to the main display where the page you selected will be shown Customizing Pages The customizing pages feature allows you to choose what data will be displayed and where it will be displayed on select pages You can customize the Single Digital Dual Digital and Fuel Manager pages with fuel flow data which includes Fuel Rate fuel flow Fuel Used Fuel Range Trip Fuel Used and Seasonal Fuel Used To customize Single Digital page 1 After the Single Digital page has been added to the page screen rotation use the UP and DOWN keys to display it on the screen 2 Press MENU select Customize and press MENU 3 Highlight FueL Flow Fut F FueL Usep USD FUEL RANGE RNG TRIP FueL Usep USD Tp or SEASONAL FUEL Usep USD SE and press MENU A menu will appear allowing you to display data from a single engine or show data from all engines on the vessel If you select FUEL RANGE RNG or
48. qual to the fuel used figure The unit will not allow you to enter a fuel amount greater than the fuel used figure 4 Use the UP and DOWN keys to input the amount of fuel added to the tank and press ENTER You will be taken back to the main display Economy Speed Source The Economy Speed menu allows you to choose what speed source Water Speed Pitot Speed or Ground Speed the LMF 400 will use to calculate Fuel Economy Ground Speed GPS is the default speed source To change Economy Speed source 1 Press MENU use the UP and DOWN keys to select System SETUP and press ENTER Select Fue Setup and press ENTER 2 Highlight Eco speen Src and press ENTER to open the Economy Speed menu The menu has three options Water Speed Paddlewheel Pitot Speed and Ground Speed GPS 3 Select the desired speed source and press ENTER You will be taken back to the main display Reset Trip Fuel The LMF 400 keeps a running total of fuel used for a trip By using the Reset Trip command you can reset to zero the running total of fuel used on a trip To reset trip fuel 1 Press MENU use the UP and DOWN keys to select System SETUP and press ENTER Select FueL Setup and press ENTER 2 Highlight Rst Trip FueL and press ENTER The Select Engine menu will appear with up to four options If you have one tank the Press Enter to reset Trip Fuel Step 3 message will appear 3 Select the desired engine or All Engines and press ENTER The following
49. r to the NMEA 2000 network setup booklet part number 988 0154 173 which came packed with this document Notes LMF 200 EP 60R Configuration amp Calibration This section covers how to use the EP 60R Fuel Flow with a LMF 200 Multi function gauge NOTE You will notice the LMF 200 does not have an Exit key Menus will time out after a preset amount of time 8 5 10 or 15 seconds The default setting is 5 seconds Refer to your LMF 200 instruction manual for more information on the Timeout feature LMF 200 Multi function Digital Gauge Boat Setup If this is the first time you have turned on your LMF 200 you will have to complete Boat Setup before you will be able to configure or calibrate your fuel flow If you have already completed Boat Setup skip ahead to the segment covering EP 60R Fuel Flow Configuration To execute Boat Setup 1 With Boat Setup highlighted on the screen press MENU The Boat Setup menu will appear allowing you to select an engine tank configuration to match the number of engines and fuel tanks on your vessel Boat Setup options include 1 En 1 Tk 1 En 2 Tk 2 En 1 Tk 2 En 2 Tk 3 En 1 Tk and 3 En 3 Tk 2 Select the correct configuration option and press MENU If you selected a configuration with more than one tank the Tank Size menu will appear If you selected a single tank configuration you will be taken directly to the Tank Size window where you can input the size of the tank 3 Selec
50. t Low LeveL or HiGH LeveL and press ENTER The Set Percentage window will appear It will be set to Off by default 5 Use the UP and DOWN keys to input the desired percentage of tank capacity that will trigger the alarm If the amount of fuel falls below the percentage you choose the alarm will go off 6 Press ENTER and you will be taken back to the Bus Devices list Press EXIT repeatedly to return to the main display NOTE To turn off a fuel warning repeat Steps 1 3 then select OFF from the Level Percentage window mentioned in Step 4 Press ENTER Repeat these steps for each warning you want to turn off Press EXIT repeatedly to return to the main display Engine Warnings Alarms The Engine Warnings feature allows you to set an alarm for one or more engines which will alert you to several engine issues including overheating and low oil pressure 29 To set an Engine Warning Alarm 1 Press MENU use the UP and DOWN keys to highlight System SETUP and press ENTER 2 Highlight ENGINE WARNINGS and press ENTER The Engine Warnings menu will appear with up to five options including Off and All Engines The default setting is All Engines If you have a single engine configuration the only options on the Engine Warning menu will be On and Off 3 Choose the desired option and press ENTER You will be taken back to the main display Displaying data from a fuel flow You can display fuel flow data on the Single Digital
51. t the tank you want to set up and press MENU which will open the Tank Size window 4 Use the UP and DOWN keys to input the number of gallons the tank will hold and press MENU Repeat steps 3 and 4 for each additional tank After all tanks have been set up you will be directed to the main display Boat Setup Reset If you want to access the Setup screen Boat Setup after an engine tank configuration has been chosen you will have to reset the configuration to default settings To reset engine tank configuration 1 Press MENU highlight System Setup and press MENU 2 Choose ENnG TANK and press MENU twice The following message will appear Hit menu to reset Eng Tnk 3 Press MENU The Setup screen will appear with Boat Setup highlighted Fuel Remaining Source FRem Src The Fuel Remaining source function allows you to select the device used to measure the amount of fuel remaining in the tank It will be set to fluid level by default To set Fuel Remaining Source to Fuel Flow Eng FFlow 1 Press MENU use the UP and DOWN keys to select System SETUP and press MENU Select FUEL MNGR and press MENU 2 Highlight FRem Src and press MENU That will open the FRem Src menu which has two options Eng FFlow and Fuel level 3 Select ENG FFLow and press MENU You can now view fuel remaining data from the EP 60R EP 60R Fuel Flow Configuration The LMF 200 can support up to three engines with one fuel flow sensor for each engine Ea
52. tructions below to ensure fuel flow Eng FF low has been selected as the Fuel Remaining Source It is set to fluid level by default Fuel Flow Accuracy To check fuel flow accuracy add the Fuel Manager page to the page screen rotation and then customize it with Fuel Used data To add the Fuel Manager page to the display 1 Press MENU use the UP and DOWN keys to select Paces and press ENTER A menu will pop up with four options Add Page Remove Page Page Scrolling and Pop Ups Setup 2 Select ADD PAGE and press ENTER 3 Highlight the Fuel Manager page and press ENTER The following message will appear Press Enter to add Fuel Manager 4 Press ENTER which will take you back to the main display where the page you chose will be shown on the screen To customize the Fuel Manager page 1 With the Fuel Manager page on the display Press MENU select CustomizE and press ENTER The data menu will appear with three options Top Data Center Data and Bottom Data each representing one of the three data boxes on the Fuel Manager page 2 Select the desired data location and press ENTER Highlight Fue Usep and press ENTER If your unit is configured for more than one tank the Select Tank menu will appear NOTE If your unit is configured for a single tank the Select Tank menu will not appear Press EXIT repeatedly to return to the main display where Fuel Used data will be displayed on the Fuel Manager page 3 Highlight the des
53. ure fuel flow and electronics which convert flow data to the NMEA 2000 data format The cable length from the connector to the smart module is 10 feet 3 meters The sensor is designed to work with gasoline only WARNING Do not use this sensor with diesel engine fuel systems The EP 60R is designed only for gasoline engines This sensor has been optimized to measure flow rates between 0 6 to 45 gallons US per hour but it will operate at flow rates outside that range The sensor will add 0 5 PSI of back pressure on the fuel system with a flow rate of 20 gallons per hour At the rate of 40 gallons per hour the back pressure will be 1 PSI The EP 60R Fuel Flow like the other LowranceNet Electronic Probe EP sensors is designed for use with a NMEA 2000 network Your sensor however 1s also compatible with LowranceNet blue connector networks It can be added to a blue connector network by using a female red to female blue adapter cable Your sensor MUST be connected to a NMEA 2000 network or it WILL NOT function The NMEA 2000 female red to female Blue adapter cable allows users to add red connector devices to a blue connector network Tools and Supplies Your EP sensor packs with a T connector needed to attach it to a LowranceNET NMEA 2000 network If this is the first sensor you are connecting you may also need to purchase of a LowranceNET Node Kit LowranceNET Node Kit for a NMEA 2000 network Includes a 2 foot extension cable
54. us Devices list where the Port fuel flow will now be displayed as UnCfg FF low 5 Select the Starboard fuel flow and press ENTER 6 Highlight CHANGE ENGINE and press ENTER The Select Engine menu will appear 7 Select PORT and press ENTER You will be taken back to the Bus Devices list 8 Highlight UnCfg FFlow and press ENTER The following message will appear Press Enter to Configure Fuel Flow Sns 9 Press ENTER which will open the Select Engine menu Choose Starboard and press ENTER You will be taken back to the Bus Devices list where both fuel flows will be shown with their new configuration names If desired configuration name available 1 Press MENU use the UP and DOWN keys to select System SETUP and press ENTER 2 Highlight Bus Devices and press ENTER The Bus Devices list will appear 3 Select the fuel flow you want to reconfigure and press ENTER Highlight CHANGE ENGINE and press ENTER The Select Engine menu will appear 4 Choose the desired configuration name and press ENTER You will be taken back to the Bus Devices list where the fuel flow you reconfigured will be displayed with its new configuration name 24 EP 60R Fuel Flow Calibration The factory calibration settings for the EP 60R Fuel Flow should be within 3 percent so calibration will not be necessary in most cases NOTE The Fuel Remaining Source must be set to fuel flow for the unit to correctly display fuel level information Follow the ins
55. use only ONE engine the engine connected to the fuel flow Burn at least 5 gallons of fuel then fill up the tank again noting how much fuel was added to the tank Check the Fuel Management page for the fuel used figure calculated by the EP 60R Fuel Flow 6 Compare the amount of fuel you added when you filled up the tank with the EP 60R Fuel Used figure If the difference between these two numbers is greater than 3 percent you need to calibrate the unit To calibrate a fuel flow 7 Press MENU use the UP and DOWN keys to select System SETUP and press MENU 8 Highlight FUEL MNGR and press MENU Select REFILL T and press MENU If your unit 1s configured for more than one tank the Select Tank menu will open Select the tank you refilled and press MENU If your unit is configured for one tank you will be taken directly to the Recalibration menu 14 9 The Recalibration The Recal menu will appear with two options Yes and No Select YEs and press MENU NOTE If you do not have the fuel remaining source set to Eng FFlow the recalibration message will not appear 10 The Filled Quantity window will appear Use the UP and DOWN keys to input the amount of fuel you added to the tank and press MENU 11 Repeat these steps for each fuel flow you want to calibrate Reset Calibration The Reset Calibration command allows you to reset a fuel flow calibration back to factory defaults To Reset Calibration 1 Press MENU use
56. ut F FueL Usep USD FUEL RANGE RNG TRIP FueL Usep USD Tp or SEASONAL FUEL Usep USD SE and press MENU A menu will appear allowing you to display data from a single engine or show data from all engines If you select FuEL RANGE RNG or if your unit is configured for one engine you will be taken back to the main display 4 Select the desired engine or to display data from all engines highlight Vessel and press MENU You will be taken back to the main display where the data you selected will be shown Reset The Reset command will reset EP 60R Fuel Flow values to default settings NOTE After using the Reset command has been executed you will have to re enter your engine tank configuration The Reset command will not affect the configuration or calibration of other devices on the network To use reset command 1 Press MENU select System SETUP and press MENU 2 Highlight Bus Devices select the desired fuel flow and press MENU The Configuration Options menu will appear 3 Select RESET and press MENU The following message will appear Hit Menu to Rst Values 4 Press MENU then let the menus time out to return to the main display 20 LMF 400 EP 60R Configuration amp Calibration This section covers how to use the EP 60R Fuel Flow with a LMF 400 Multi function gauge L LOWRANCE LMF 400 Multi function Digital gauge Boat Setup If this is the first time you have turned on your LMF 400
57. ut completely filling it up you must use the Partial Fill command This will ensure the fuel information in the EP 60R stays consistent with the amount of fuel actually in the tank To use Partial Fill 1 Press MENU use the UP and DOWN keys to select System SETUP and press MENU Highlight FUEL MNGR and press MENU 2 Highlight PART FILL and press MENU The Select Tank menu will appear with up to three options If you have one tank you will be taken directly to the Fuel Quantity window Select the desired engine and press MENU NOTE When using the Partial Fill command you will only be able to input an amount of fuel less or equal to the fuel used figure The unit will not allow you to input a fuel amount greater than the fuel used figure 3 The Fuel Quantity window will appear Use the UP and DOWN keys to enter the amount of fuel you added to the tank and press MENU You will be taken back to the main display Economy Speed Source Eco spd The Economy Speed Source menu allows you to choose the speed source Water Speed Pitot Speed or Ground Speed the LMF 200 will use to calculate Fuel Economy Ground Speed GPS is the default speed source for Fuel Economy To change Economy Speed Source 1 Press MENU use the UP and DOWN keys to select System SETUP and press MENU Select FUEL MNGR and press MENU 2 Highlight Eco spp and press MENU which will open the Eco spd menu The menu has three options Water Spd Water Speed
58. you will have to complete Boat Setup before you will be able to configure or calibrate your fuel flow If you have already completed Boat Setup skip ahead to the segment covering EP 60R Fuel Flow Configuration To execute Boat Setup 1 With Boat Setup highlighted on the screen press ENTER A menu will appear allowing you to choose the number of engines and fuel tanks on your vessel The Boat Setup menu options are 1 Eng 1 Tank 1 Eng 2 Tank 2 Eng 1 Tank 2 Eng 2 Tanks 3 Eng 1 Tank or 3 Eng 3 Tanks 2 Use the UP and DOWN keys to select the engine tank configuration that applies to your vessel and press ENTER After setting the engine tank configuration the Tank Size menu will appear with up to three options If you selected one tank during Boat Setup you will be taken directly to the Setting Tank Size Window in Step 4 3 Select the desired tank and press ENTER which will open the Setting Tank Size window 4 Use the UP and DOWN keys to input the size of the tank and press ENTER Repeat steps 3 and 4 for each of the remaining tanks 5 After all tanks on your vessel have been set up press EXIT repeatedly to return to the main display 21 Boat Setup Reset If you want to access the Setup screen Boat Setup after an engine tank configuration has been chosen you will have to reset the configuration to default settings To reset engine tank configuration 1 Press MENU highlight System Setup and press ENTER 2 Choose ENG

Lowrance electronic EP-60R User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents