Linksys LKG0F755E User's Manual
Contents
1. The OneTouch button currently does not work with the Network Storage Link You may use the included Retrospect Express backup software however for automated backup of your files on one computer See page 6 for more information USB Only The Network Storage Link is not compatible with FireWire You may ONLY use a USB compatible OneTouch drive Windows Only The Network Storage Link currently supports Windows 98SE ME 2000 and XP only Installing the Network Storage Link and OneTouch Drive Connecting the Network Storage Link to Your Network 1 Connect one end of an Ethernet cable to the Ethernet port on the back of the Network Storage Link GO 2 Connect the other end of the Ethernet cable to your router Figure 1 Connecting the Ethernet cable Connecting the OneTouch Drive to the Network Storage Link Important Make sure that the Network Storage Link is turned OFF before you connect or disconnect your Maxtor OneTouch drive 3 Connect one end of the included USB cable to your OneTouch drive 4 Connect the other end of the USB cable to the Disk 1 port on the Network Storage Link Figure 2 Connecting the USB cable Note You can only connect up to two drives Do NOT connect additional drives using a USB hub Powering Up the OneTouch Drive 5 Connect the round female connector from the power adaptor to the drive s power connector woh oou cd 6 Connect the two pin fema2. See Chapter 6 Configuring the Storage Link in the Linksys User Guide for more information Your OneTouch drive is now ready for use as a networked drive You may drag and drop files to it just like a normal hard drive Network Backup Software Your OneTouch drive includes Retrospect Express backup software for easy automated backup of your important files If you would like to backup files from a computer on your network follow the steps outlined in the next section Note You may only install the Retrospect Express software on one computer However you may purchase additional copies of Retrospect by going to http www dantz com Retrospect Software Installation 1 Go to Chapter 2 Installing Your Drive in the Maxtor OneTouch User s Guide 2 Find the Installing the Software section for your operating system Your options are Windows 2000 and XP or Windows 98SE and ME 3 Follow the installation steps choosing the Full Installation option Note When you have completed the software installation do not proceed to the Connecting the Drive or Setting up the Maxtor OneTouch Feature sections For step by step directions on how to back up your entire computer system using Retrospect see the following section Automated Network Backup Using Retrospect 1 Open Retrospect 2 On the left side of the screen click the sign all next to Automate and then click EasyScript Retrospect Backup Th
3. and the folder IP address of your Network Storage that you want to connect to Link followed by Disk 1 using this a im format IP address Disk 1 Bee Geers v Fee Example serverishare For example 192 168 1 77 Disk 1 IReconpect egon Connect using a different user name Note Make sure there is a space i ia e er ta a se between Disk and 1 in the IP address Note If you changed the IP address in the Formatting the OneTouch Drive Figure 6 Entering IP Address of Network Storage Link section on page 3 be sure to enter that address here Note Reconnect at logon is automatically selected This means that every time you logon in the future you will automatically be connected to your OneTouch drive You will find it alongside your computer s main disks C and D for example in the My Computer window 3 Click Finish Windows will search the available networks for your Network Storage Link and a window will open displaying the contents of the Disk 1 directory on your OneTouch drive Note Two directories are automatically created for you on your OneTouch Drive The Admin 1 directory is set up for only the administrator to use and will require a User ID and Password to be entered by any user accessing it from a computer other than the administrator s The Disk 1 directory however does not require a User ID or Password You may create password protected directories for additional users
4. LINKSYS Maxtor A Division of Cisco Systems Inc What drives you Getting the most from your he Maxtor OneTouch USB hard drive and Linksys Network Storage Link Share your OneTouch drive with everyone on your network PA With the Linksys Network Storage Link you can now use your Maxtor OneTouch USB hard drive as a network hard drive This document shows you how to install everything and get up and running as quickly as possible What are the benefits of a network drive Share information Keep your files photos or MP3s in one central location Every PC or selected users on your network can access the information Save money No need to keep a PC or server turned on all the time for files to be available your network hard drive is always accessible Protect your valuable data With the included Retrospect Express backup software you can schedule automated backups to your network hard drive Before you install please read Not Hot Swappable Make sure that the Network Storage Link is turned OFF before you connect or disconnect your Maxtor OneTouch Drive Drive Format When using the OneTouch drive as a network drive it must be connected to the Network Storage Link ONLY as it is formatted using a non Windows file system The OneTouch drive may NOT be connected directly to a Windows system without reformatting Warning Reformatting will erase all of your data t OneTouch Button
5. d on
6. e EasyScript welcome window Restore will appear E Automate EasyScript 3 Click Next Manage Scripts Validate Scripts The next window will ask you to choose your RE backup media EE Configure 4 Select Disks and click Next Figure 7 EasyScript The next window will ask you how many backup sets you want 5 Select want one Backup Set for everything and click Next The next window will ask you how often you would like to back up 6 Choose either Once a week or Every weekday and click Next If you chose Once a week you will choose the day and the start time If you chose Every weekday you will choose only the start time 7 Make your choice s and click Next The Backup Summary window will appear showing the backup options you have chosen The Start the first backup now checkbox is checked which means your first backup will start when you click Finish Note It is recommended that you start your first backup now because you will choose the source and destination of your backup the first time you do it If you choose not to start your first backup now you will need to be at your computer for the first scheduled backup to choose the source and destination of your backup 8 Click Finish If you chose the Start the first backup now option Retrospect will scan your drive and the Backup Set window will appear You will now choose the disk where your backup files will be stored 9 Double click My Network Places The Adding Networ
7. he top of the screen and an icon and the name of your Storage Link will appear in the Selection Column On the right side of the screen you will see the IP Address of your Network Storage Link 14 Write down this IP Address You will need it later to use your networked OneTouch drive Note If your Network Storage Link is not found try clicking Search Again If it is still not found see Appendix A Troubleshooting in the Linksys User Guide Once your Storage Link is found the next step is to format your OneTouch drive Keep the Linksys setup screen open and proceed to the next section Formatting the OneTouch Drive 15 On the left side of the Linksys setup screen double click the icon for your Network Storage Link Selection Figure 4 Network Storage Link Icon A web browser will open and the Home page for your Network Storage Link will appear Note If your web browser does not automatically open follow the steps in Chapter 6 Configuring the Storage Link in the Linksys User Guide Note If you receive a page cannot be displayed message you may need to change the IP address URL of your Network Storage Link See Chapter 4 Setting Up the Storage Link in the Linksys User Guide for information about changing the Network Storage Link s settings If you change the IP address of your Network Storage Link be sure to write down the new number as you will need it to use your networked OneTouch dr
8. ive after formatting 16 Click Administration A window will open asking you to enter your user name and password 17 Enter admin for both user name and password and click OK The LAN page will appear 18 Click Advanced The Groups page will appear 19 Click Disk The Disk page will appear 20 Click Format Disk 1 Note If your drive is connected to the Disk 2 port on the Network Storage Link click Format Disk 2 The formatting process may take 15 to 30 minutes depending on the size of your OneTouch Drive Once it is finished the message Formatted will appear 21 Close your web browser and click No at the bottom of the Linksys Setup Screen Note For more information about the Linksys Web Utility see Chapter 6 Configuring the Storage Link in the Linksys User Guide Using Your Networked OneTouch Drive To use your networked OneTouch Drive follow these steps 1 On the desktop right click the icon for your computer and choose Map Network Drive Open Explore Search Manage Map Network Drive Disconnect Network Drive Create Shortcut Delete Rename Properties Figure 5 Mapping a Network Drive The Map Network Drive window Map Network Drive wi Il a p pear Windows can help you connect to a shared network Folder and a ae terte Gs connect so that you can access the Folder using My Computer 2 In the Folder or Path box enter the Specify the drive letter for the connection
9. k Volume window will appear 10 Click Advanced A window will open asking you to enter the UNC path for the volume 11 Enter the IP address of your Network Storage Link followed by Disk 1 using this format IP_ address Disk 1 For example 192 168 1 77 Disk 1 Note If you changed the IP address in the Formatting Your Drive section on page 3 be sure to enter that address here 12 Click OK Disk 1 will now appear under My Network Places in the Backup Set window 13 Select Disk 1 and click Proceed The Add New Member window will appear to confirm your backup destination 14 Click OK The backup will now start Note Your entire computer system including all of its drives will automatically be backed up Depending on the size of your system and the speed of your network this process may take as much as several hours For example on a home wireless network of less than 10 megabits per second a 10 gigabyte backup would take over three hours If you wish to change the specific items that are backed up or learn how to restore files from a backup see the Retrospect online help in the Retrospect Express software When the backup is finished you will see the message Execution completed successfully Congratulations You have completed your first backup Future backups will take place automatically on the days and times that you selected as long as the computer OneTouch drive and Network Storage Link are turne
10. le connector on og the power cord to the power adaptor Figure 3 Connecting the power 7 Connect the standard 3 pin electrical plug to an AC power outlet preferably a surge protected outlet 8 Turn on the OneTouch drive using the switch on its back panel Powering Up the Network Storage Link 9 Connect one end of the power adaptor to the back of the Network Storage Link 10 Connect the other end of the power adaptor to an AC power outlet preferably a surge protected outlet 11 Turn on the Network Storage Link by pressing its front panel button The Network Storage Link may take up to three minutes to completely power up During this time the Ready Status light will flash When the Ready Status light stops flashing and remains solid green the Network Storage Link is ready for use Note For more information about the lights on the Network Storage Link see Chapter 3 Connecting the Storage Link in the Linksys User Guide Installing the Linksys Software 12 Insert the Setup Wizard CD into your computer The Linksys Main Menu screen should appear after a few seconds Note If the main menu does not appear see Chapter 4 Setting Up the Storage Link in the Linksys User Guide 13 Click Setup The Linksys software will search for the Network Storage Link connected to your network When your Network Storage Link is found the message Network Storage Link s Have Been Found will appear at t
Download Pdf Manuals
Related Search