Jet Tools DC-1200CK User's Manual
Contents
1. 2 Flat WashOt estie ite PER tta tet et d VL 1 Pan Head Bolt W Flange M6X12 iio 8 Flat Washer E tta tet t MB 34 Spring Washo astir eea tarte te reb iud 8 Spring Waslief P e ibas 4 Tapping MbX12 i ied 2 Grounding Label not Hee 1 Direction Label not 1 0 Hee 1 Name Plate not 1 Hardware Package not 1 Centrifugal Switch not semen 1 Warning Label not 0 1 16 Parts Breakdown Canister Index Filter Assembly Part No Description Size Qty 331050 inei Handie 1 5 1540071 rette tesa ter dee tete qs 2 5 1550071 Flat Washer ccc etin rtu MO tete 2 5 2361101 Lock aceite needs de 1 000052 3 331014 iiec Gales2. Base Unit SN 710700 Base Unit SN 710720 Filter Bag Kit SN 708636F Canister Filter Kit SN 708639B DC 1200BK 1200 DC 1200 3BK X X DC 1200 3CK X X Table DC 1200 Dust Collector cartons Hardware Bag for Base Unit SN DC1100 HP 16 M8 x 16 Hex Cap Screws K 22 M8 Flat Washers L 8 M6 x 12 Pan Head Flange Screws M 6 M8 Hex Nuts N 16 M8 x 16 Hex Cap Screws 22 M8 Flat Washers A WO 8 M6 x 12 Pan Head 6 8 Hex Nuts Flange Screws c Vs m Assembly Hardware Shipping Content Base Units SN 710700 and 710720 1 Housing A 2 Hose Clamps B 1 Hose 1 Impeller Motor Fan Assembly D 1 Inlet Port E 1 Impeller Cover 3 Support Legs 1 Base 4 Casters J 1 Owner s Manual not shown 1 Warranty Card 1 Hardware Bag SN DC1200 HP 9994 Base Machine Shippin Canister Filter Kit Bag Filter Kit SN 708639B 1 Handle SN 708636 1 Canister Filter 1 Upper Bag 1 Snap Ring 1 Hanger 2 5 1 Collector 1 Canister Filter Hardware Bag SN DC1100 CHP 1 Piker Bag Contains 1 Retainer Strap AA 2 M10 Hex Nuts S 2 M10 Flat Washers T 1 M10 Lock Washer U 4 Knobs V Filt
3. 15 Removing the Collector Bag DC 1200CK and 1200 3 15 ERES 15 Connecting the Dust Collector to a Machine pp 15 Grounding the Dust Collection eme eene EEATT AEAEE EA 15 17 Canister Filter Assemb 22 08 PER 18 Assemb REP ov eR ete e Ede tins dete 19 Warnings 10 11 12 13 14 15 16 17 18 19 Read and understand the entire owner s manual before attempting assembly or operation Read and understand the warnings posted on the machine and in this manual Failure to comply with all of these warnings may cause serious injury Replace the warning labels if they become obscured or removed This dust collector is designed and intended for use by properly trained and experienced personnel only If you are not familiar with the proper and safe operation of a dust collector do not use until proper training and knowledge have been obtained Do not use this dust collector for other than its intended use If used for other purposes Walter Meier Manufacturing Inc disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use Always wear approved safety glasses face shields while using this dust collector Everyday eyeglasses only have impact resistant lenses they are not safety glasses Before operating this
4. Cleaning the Filter Bag DC 1200BK and DC 1200 3BK ACAUTION Wearing a particle mask or respirator for protection against fine dust particles during cleaning is highly recommended During first use and after cleaning the filter bag may allow some dust to escape This is normal and will stop after a short period of time Clean both the filter and collector bags frequently to keep the collector s performance at its optimum To clean 1 Disconnect the machine from the power source 2 the filter bag from the hanger and shake the bag so that the majority of the dust falls into the collector bag 3 Loosen the retaining strap and remove the filter bag from the housing Turn the bag inside out and clean 5 Turn the bag outside and re attach to the housing using the retainer strap to secure Removing the Collector Bag DC 1200BK and DC 1200 3BK 1 Disconnect the machine from the power source 2 Remove the collector bag by pushing the ring of the collector bag upwards and pulling the bag out at an angle 3 Empty the contents into an appropriate container 4 Turn the bag inside out and clean 5 Turn bag outside in and insert into the housing To replace the collector bag refer to Collector Bag Installation on page 11 Use the proper type hose to connect the dust collector to the machine being operated Dryer vent hose is not acceptable for this purpose Contact your nearest JET
5. 1 150623 comm 1 33105 she Soft Grip Hand 2 5 1540041 8 708739 1 331052 Krems 1 TS 1482044 Hex Cap tet utm an 4 5 2361061 Lock Washer 2 0 1 4 5 1550041 Flat Washer et Erie ene e 4 331012 III 2 331017 rd 2 3310015 Press ae 2 5 1482021 MOXA 2 ars 4 933109 nes 4 331031 PAG Heiss EA T AN E e OH 1 331009 ee 1 57049200 Tapping amp 4 331038 SNAP RING 1 709563 5 DC1100 CHP Canister Hardware 18 Filter Bag Assembly Index Description Size Qty 708698 Filter Bag EDEN SG 30 Micron Bag 708702 Filter Bag
6. EE NM UN 2 micron Collector Bag Capacity ft 5 6 Remote Control Unit Optional Stock Number main unit and remote control switch 230V 708636D Stock Number Remote Control Switch 708636T The above specifications were current at the time this manual was published but because of our policy of continuous improvement Walter Meier reserves the right to change specifications at any time and without prior notice without incurring obligations Ordering Replacement Parts Replacement parts are listed in the back of this manual To order parts or reach our service department call 800 274 6848 Monday through Friday see our website for business hours www waltermeier com Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately Unpacking The table below lists the shipping cartons that are included with the various models of the DC 1200 Dust Collector 1 Locate your particular model and verify that you have received the all the correct cartons 2 Check contents of each carton against the ship ping content listings on this and the following page Report any damage to your distributor 4 Do not discard any shipping material until after the dust collector has been assembled and is running properly
7. JET Operating Instructions and Parts Manual Dust Collector DC 1200 Series Dust Collectors A 1 DC 1200BK DC 1200CK WALTER MEIER Manufacturing Inc 427 New Sanford Road LaVergne Tennessee 37086 Part No M 710700 Ph 800 274 6848 Revision A1 03 2010 www waltermeier com Copyright 2010 Walter Meier Manufacturing Inc Warranty and Service Walter Meier Manufacturing Inc warrants every product it sells If one of our tools needs service or repair of our Authorized Service Centers located throughout the United States can give you quick service In most cases any of these Walter Meier Authorized Service Centers can authorize warranty repair assist you in obtaining parts or perform routine maintenance and major repair on your JETe tools For the name of an Authorized Service Center in your area call 1 800 274 6848 MORE INFORMATION Walter Meier is consistently adding new products to the line For complete up to date product information check with your local Walter Meier distributor or visit waltermeier com WARRANTY JET products carry a limited warranty which varies in duration based upon the product MW Metalworking WW Woodworking Body Repair Kits Beam Clamps 5 Bottle Jacks Chain Hoist Cable Pullers Manual Cold Saws YEAR YEAR Lever Hoists YEAR Hoists Air KEARI Pullers JCH Models HERR Hoists Electric Palet Trucks Scissor Lift Tables WW Drill Presses Fastening Too
8. 5 Micon AB410012 Retainer tese 708699 430038 HANG Deest Rer Dead be ose dus 30 Micron Bag Hanger sands ha tune te tan AB430039 Hanger 5 Micron Bag Hanger 523011W Hanger Bracket ettet et E exer am aN ff 1 460V 230V 230V i 901 019 Ve Vi MOTOR Wiring Diagram For 3 Phase 230V 460V Dust Collector DC 1200M 3 MOTOR CORD POWER SUPPLY CORD 0 S SWITCH GREEN GROUND WIRE R T GREEN GROUND WIRE PR MOTOR CORD 5 POWER SUPPLY CORD e SWITCH D R T Wiring Diagram For Single Phase 230V Only Dust Collector DC 1200M D BLACK SWITCH BLACK 22 WHITE WHITE 9 19 MOTOR CORD POWER SUPPLY CORD GREEN GROUND WIRE 20
9. Unit Assembly o DRE Tbe donee eA EE Ett 9 9 Motor and FanAssemibly 9 Connector HOUSING EET 10 EE 10 Filter Bag Kit Assembly E em 11 Filter Bag Installation devas Le ena e Ra EE ERR 11 Collector Bag Installation teint edited nn tere we Eua daa 11 Canister KEASSemMDIY ie diee Leod en D nnd LE se LUC a dha ened ete 12 Canister FINGI edo Ee edd t e aono EE Ee c das eua Ld ERR ae 12 Collector Bag RET 12 Electrical COnneCtiOns ses 13 Turning the Machine On amp Off osiers ekerin nannini RARE AAEE TAAA 13 13 Remote Neo OE 13 Turning the DCG RC230 Otr amp Off i oe er Hb HE ce ERE a EE e 13 Changing Operating Frequency 5 2 e REP 14 Installing the DC RC Remote Power Control pp 14 MEE ES 15 Cleaning the Filter Bag DC 1200BK and 1200 3 15 Removing the Collector Bag DC 1200BK and 1200 3 15 Cleaning the Canister Filter DC 1200CK and 1200
10. dust collector remove tie rings watches and other jewelry and roll sleeves up past the elbows Remove all loose clothing and confine long hair Non slip footwear or anti skid floor strips are recommended Do not wear gloves Wear ear protectors plugs or muffs during extended periods of operation Some dust created by power sanding sawing grinding drilling and other construction activities contain chemicals known to cause cancer birth defects or other reproductive harm Some examples of these chemicals are Lead from lead based paint Crystalline silica from bricks cement and other masonry products Arsenic and chromium from chemically treated lumber Your risk of exposure varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as face or dust masks that are specifically designed to filter out microscopic particles Do not operate this machine while tired or under the influence of drugs alcohol or any medication Make certain the switch is in the OFF position before connecting the machine to the power supply Make certain the machine is properly grounded Make all machine adjustments or maintenance with the machine unplugged from the power source Remove adjusting keys and wrenches Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before turning it on Keep safety gu
11. either your local supplier or Walter Meier Manufacturing Inc Specifications Base Machines 1200 1200 3 uicti patentes t ere e e 710720 Blower Wheel Diameters oder olv abet ee 12 Sournd Rating at 70 80 db DIGG 4 amp 6 GEM eerte RUM GL 1 200 Melocity at A EF PM RE ae RI m E eroe 13 745 static Pressure inch of Water exceed creed eade ee needed eral XXI dhe Min 11 44 Overall Dimensione een ariere ect ode RA MR ERRORI E ER CHER Ped 37 L x 28 W x 79 H Motor TEFC 2 HP 1Ph 230 2 HP 3Ph 230 460 Prewired 230V Ner Veig 140 Ibs Filter Kit Sois Be E RO od 708636 Bag Diameter 20 Filter Efficiency 30 micron Collector Bag Capacity ft 5 6 Canister Filter lt 708639B Bag Da 20 Filter Efficiency
12. 0MFD 300 1 Starting Capacitor not 200MFD 125V 1 BOX 1 EE 1 EE 1 E 1 E 1 Motor Packing EE 1 Impeller 1 as 1 VA TR 1 Net Cap EM 2 erennert Fee od eo AT a 1 E eee A OT T 1 Pivoting Caster cede ee eee EAR R EENAA EEA e depo owe ds 4 HOUSING E E T 1 67 a iH 3 poi 5 5 1 Ring Clamp eite eere tee dines 2 Tapping M3 5x12 AB 6 ic Lo 1 ea eke 10 ai and 3 87 160 4 Hex Head Bolt 8 20 1 Hex Head Bolt MBX12 4 Hex Head 16 Hex Head Bolt iet rt 4 Pan Head Bolt W Flange MOX12
13. ERCHANTABILITY AND FITNESS ARE EXCLUDED SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU WALTER MEIER SHALL IN NO EVENT BE LIABLE FOR DEATH INJURIES TO PERSONS OR PROPERTY OR FOR INCIDENTAL CONTINGENT SPECIAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU Walter Meier sells through distributors only The specifications in Walter Meier catalogs are given as general information and are not binding Members of Walter Meier reserve the right to effect at any time without prior notice those alterations to parts fittings and accessory equipment which they may deem necessary for any reason whatsoever branded products are not sold in Canada by Walter Meier 2 Table of Contents peces rco toten decies ee petes patie 2 Ie 3 aret ES 4 AE 6 sete nag ce oe Aaa ant LU ak ML MIX MIL m P 6 Ordering Replacement Parts ied cH CHR e re vd EE ARR RR e PAR ERR TERRE Dea and Tag eR 6 7 Shipping Contenen eee oves NODUM tutem mme emer E UL dd 7 XN cS 7 Canister Filter 8 iecit 8 Base
14. ards in place at all times when the machine is in use If removed for maintenance purposes use extreme caution and replace the guards immediately Check damaged parts Before further use of the machine a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment of moving parts binding of moving parts breakage of parts mounting and any other conditions that may affect its operation A guard or other part that is damaged should be properly repaired or replaced Provide for adequate space surrounding work area and non glare overhead lighting Keep the floor around the machine clean and free of scrap material oil and grease Keep visitors a safe distance from the work area Keep children away Warnings 20 21 22 23 24 25 26 27 Make your workshop child proof with padlocks master switches or by starter keys Give your work undivided attention Looking around carrying a conversation and horse play are careless acts that can result in serious injury Do not use the dust collector for anything except wood dust Materials such as liquids metal shavings metal dust screws glass plastic or rock can cause sparks and or damage when coming into contact with any part of the dust collector Use recommended accessories improper accessories may be hazardous Maintain tools with care Follow i
15. at may be present and located within the radio frequency range 5 Set the DIP switches C in the remote control switch B to match the switch settings in the main unit 6 Replace the back covers to the main unit and remote control switch 7 Operate a device as described in Turning the DC RC230 On amp Off and verify that other devices using the same type remote control do not turn on Figure 14 Installing the DC RC Remote Power Control The DC RC230 Remote Power Control unit can be placed anywhere for convenience and portability if used to control other machines or it can be mounted as a permanent part of a machine such as the DC 1200 Dust Collector 14 To mount the DC RC230 Remote Power Control refer to Figure 15 Note Mounting hardware is not included and must be supplied by the machine s owner or user 1 Place RC Power Control Unit A on the open clearing of the base B of the dust collector near the motor C 2 Using a marker mark the base through the mounting holes of the power control units mounting tabs 3 Drill two holes D through the base where marked 4 Insert screws through the tabs and base Place washers and hex nuts on the threaded ends of the screw underneath the base and tighten Figure 15 Maintenance AWARNING Never perform maintenance on this machine before turning switch off and removing plug from power source Failure to comply may cause serious injury
16. being operated Dryer vent hose is not acceptable for this purpose Contact your nearest JET distributor for the full line of JET Dust Collector Hoses and Accessories Customize your installation and obtain maximum performance with JET s dust hoods hoses clamps fittings and blast gates Grounding the Dust Collection System The dust collection system includes the dust collector and the hose or ductwork you use to connect the tools dust collector is grounded though the ground wire in the cord The hose or ductwork you use to connect the tool to the dust collector must also be grounded To assist in grounding your system you can purchase the JET Dust Collector Grounding Kit stock JW1053 through JET Distributors Index No Part No TS 1490011 TS 1490021 TS 1490041 TS 1554041 TS 0680031 TS 1554041 TS 0680031 TS 0720081 TS 1551071 ST059304 DC1200 53 DC1200 54 DC1200A NP DC1100 HP DC1200A CS DC1900 53 Parts List for the DC 1200M DC 1200M 3 Description Size Qty day orsi Housing E 1 Motor 2 nnt RE E ERR MEER EE ID 1 AT IERI D LUCNDOLLOIUDEEI LUI MEER 1 2 Phaser tdt 1 huoc 2 tete 1 Motor Fan Cover not shown sn 1 Motor Fan not 1 Running Capacitor not 3
17. dedicated circuit to the dust collector will give you the best results since dust collectors are generally used at the same time other tools are running Turning the Machine On amp Off All Models Before hooking up to the power source make sure that the switch is in the off position This machine is intended for indoor use only Turn the dust collector on by pressing the Start button mounted next to the motor Press the Stop button to turn off the dust collector Remote Control optional If you have the DC 1200BK or DC 1200CK the DC RC230 RF Remote Power Control unit is available as an optional accessory contact Customer Service by calling the number on the cover Important The DC RC230 Remote Power Control can be used for activating Dust Collection units powered by 230V only up to 3HP single phase only en J 7 I T RADIO FREQUENCY RF TRANSMITTER CONTROL SWITCH Figure 12B QUENCY RF TRANSMITTER CONTROL SWITON Figure 12A 13 Dust Collector RF Remote Power Control optional The DC RC230 Remote Power Control Figure 13 should be used for activating Dust Collection units powered by 230V only up to 3HP 1 Phase The DC RC230 Remote Power Control unit is rated at 230V Single Phase only Use an outlet rated at least 20amps The circuit for the device being controlled by the DC RC230 should also be protected by at least a 20 amp circuit breaker or fuse Before hooking up
18. distributor for the full line of JET Dust Collector Hoses and Accessories Customize your installation and obtain maximum performance with JET s dust hoods hoses clamps fittings and blast gates 15 Cleaning the Canister Filter DC 1200CK and DC 1200 3CK AWARNING Never perform maintenance on this machine before turning switch off and removing plug from power source Failure to comply may cause serious injury Clean both the filter and collector bags frequently to keep the collector s performance at its optimum To clean the filter turn the handle a couple of rotations so the dust falls into the collector bag Removing the Collector Bag DC 1200CK and DC 1200 3CK ACAUTION Wearing particle mask respirator for protection against fine dust particles during cleaning is highly recommended 1 Disconnect the machine from the power source outlet 2 Remove the collector bag by pushing the ring of the collector bag upwards at an angle and pulling the bag and snap ring out 3 Empty the contents into an appropriate container To replace the collector bag refer to the Collector Bag Installation on page 12 Motor Make frequent inspections of the motor fan and blow out with low pressure air hose or vacuum any accumulation of foreign material in order to maintain normal motor ventilation Connecting the Dust Collector to a Machine Use the proper type hose to connect the dust collector to the machine
19. er Bag Kit Contents Canister Filter Kit Contents Canister Filter Hardware SN DC1100 CHP O S 2 M10 Hex Nut 2 M10 Flat Washer U 1 M10 Lock Washer 4 16 20 Knob Canister Filter Hardware AWARNING Read and understand the entire contents of this manual before attempting set up or operation Failure to comply may cause serious injury 8 Base Unit Assembly Base 1 Install four casters to the under side of the base as pictured in Fig 2 Referring to Figure 1 2 Thread the hex nut B onto the caster shaft Then slide the ock washer A over the caster shaft Thread the caster shaft into the threaded hole on the underside of the base turn until snug Tighten the nut B against the base with a 14mm wrench This will give the caster proper clearance Motor and Fan Assembly Referring to Figure 2 3 Place the base C with casters on the ground Attach the motor and fan assembly to the base using four each M8 x 16 hex cap screws and M8 flat washers B Tighten with a 13mm wrench AWARNING The dust collector must not be connected to the power source during assembly Failure to comply may result in serious injury Referring to Figure 3 4 Attach impeller cover A to fan housing D using eight M6 x 12 pan head screws B Press the inlet ports C onto the inlet guard until it snaps into place AWARNING To reduce the risk of injury from moving parts always keep inlet p
20. g A Fig 11 of the collector bag into the bottom of the housing at an angle 5 Pull down on the ring to make sure it seats in the housing Note make sure the snap ring snaps into place in the housing and also that the plastic bag hangs down approximately 3 so that there are no air leaks 12 hex nut flat washer flat washer handle lock washer hex nut knob Figure 9 Fold the plastic bag over the op of the snap ring Figure 11 Electrical Connections All electrical connections must AWARNING be done by a qualified electri cian All adjustments or repairs must be done with the dust collector disconnected from the power source unplugged Failure to comply may result in serious injury The DC 1200BK CK dust collectors are rated at 230V Only The DC 1200 is not supplied with a plug Use a plug and outlet rated at least 20 amps The circuit for the machine should also be protected by at least a 20 amp circuit breaker or fuse The DC 1200 3BK and DC 1200 3CK are rated at 3 Phase 230V 460V Prewired 230V If you want to run these on 460V refer to the wiring diagram found on the inside of the switch box cover Keep in mind that a circuit being used by other machines tools lights heaters etc at the same time will add to the electrical load A
21. ls Metal forming Rigging WW Benchtop Screw Jacks WW Dust Collectors Paris Hand Tools achine Accessories Contractor Mil Dril Servico Jack Trolleys Geared WW Dust Filt Mobile Bases Air Tools Industrial en Striking Tools 5 Milling Machines Stackers Trolleys Plain WW Dust Fittings Safety Equipment Air Tools Light MW Bandsaws Surface Grinders Winches Manual WW Jointers Specialty Items Industrial MW Drill Presses Tapping WW Air Filtration WW Lathes Vise Accessories Lubrication MW Finishing Trolleys Air WW Bandsaws WW Planers WW Shapers Equipment Trolleys Electric WW Buffers WW Sanders WW Tablesaws MW Lathes Web Slings MW Precision Vises Winches Electric Vises no precision Clamps Warranty reverts to 1 Year Warranty if woodworking WW products listed above are used for industrial or educational purposes WHAT IS COVERED This warranty covers any defects in workmanship or materials subject to the exceptions stated below Cutting tools abrasives and other consumables are excluded from warranty coverage WHO IS COVERED This warranty covers only the initial purchaser of the product WHAT IS THE PERIOD OF COVERAGE The general JET warranty lasts for the time period specified in the product literature of each product WHAT IS NOT COVERED Five Year Warranties do not cover woodworking WW products used for commercial industrial or educational purposes Woodworking product
22. nstructions for lubricating and changing accessories Turn off the machine before cleaning Use a brush or compressed air to remove chips or debris do not use your hands Do not stand on the machine Serious injury could occur if the machine tips over Never leave the machine running unattended Turn the power off and do not leave the machine until it comes to a complete stop Remove loose items and unnecessary work pieces from the area before starting the machine Never place hands near the inlet of the machine Always make certain machine is off and unplugged when making any connections to the inlet Familiarize yourself with the following safety notices used in this manual ACAUTION This means that if precautions are not heeded it may result in minor injury and or possible machine damage AWARNING This means that if precautions are not heeded it may result in serious injury or possibly even death SAVE THESE INSTRUCTIONS Introduction This manual is provided by JET covering the safe operation and maintenance procedures for model DC 1200 Series Dust Collectors This manual contains instructions on installation safety precautions general operating procedures maintenance instructions and parts breakdown This machine has been designed and constructed to provide years of trouble free operation if used in accordance to instructions set forth in this manual If there are any questions or comments please contact
23. ort covered with the caps provided if they are not connected to a hose Failure to comply may result in serious injury Figure 1 2 3 Connector Housing B 5 Attach three support legs A 4 to the base Le using six M8 x 16 hex cap bolts and six 8 flat washers Fig 4 Hand tighten only at this time re LI 6 Install the housing A Fig 5 to two support legs B Fig 5 using four M8 x 16 hex cap bolts eight M8 flat washers and four M8 hex nuts C Fig 5 Be sure hose opening faces fan housing Note For models DC 1200BK or DC 1200 3BK only Before attaching third support bracket place the hanger bracket D Fig 5 between the support bracket and the housing 7 Tighten all nuts and bolts at this time with a 13mm wrench Figure 5 Hose Referring to Figure 6 8 Attach the hose B between the fan housing A and the impeller housing with two clamps Tighten the clamps to secure the hose This completes the Base Unit assembly If you purchased the DC 1200BK or DC 1200 3BK Dust Collector filter bag version continue on the following page If you purchased the DC 1200CK or DC 1200 3CK Dust Collector canister filter version proceed to Canister Kit Assembly section on page 12 Figure 6 10 Filter Bag Kit Assembly If you purchased Model DC 1200BK or DC 1200 3BK Dust Collector this section describes the as
24. s with Five Year Warranties that are used for commercial industrial or education purposes revert to a One Year Warranty This warranty does not cover defects due directly or indirectly to misuse abuse negligence or accidents normal wear and tear improper repair or alterations or lack of maintenance HOW TO GET SERVICE The product or part must be returned for examination postage prepaid to a location designated by us For the name of the location nearest you please call 1 800 274 6848 You must provide proof of initial purchase date and an explanation of the complaint must accompany the merchandise If our inspection discloses a defect we will repair or replace the product or refund the purchase price at our option We will return the repaired product or replacement at our expense unless it is determined by us that there is no defect or that the defect resulted from causes not within the scope of our warranty in which case we will at your direction dispose of or return the product In the event you choose to have the product returned you will be responsible for the shipping and handling costs of the return HOW STATE LAW APPLIES This warranty gives you specific legal rights you may also have other rights which vary from state to state LIMITATIONS ON THIS WARRANTY WALTER MEIER MANUFACTURING INC LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT EXCEPT AS STATED HEREIN ANY IMPLIED WARRANTIES OR M
25. sembly and installation of the contents of the Filter Bag Kit a SN 708636F FI Filter Bag Installation Referring to Figure 7 1 Place the hanger A on the hanger bracket 2 Slide the filter bag loop over the hanger hook 3 Feed the retainer strap D through the loops on EQUIPMENT the filter bag E and fasten to the collector housing F Collector Bag Installation Referring to Figure 8 4 Insert the ring of the collector bag A at an angle into the housing through the opening at the bottom Pull down on the bag to make sure it seats in the housing 5 Position the plastic window in front so that you can easily see when the collector bag is full After completing the filter bag and collector bag installation proceed to Electrical Connections Figure 8 11 Canister Kit Assembly If you purchased Model DC 1200CK or DC 1200 3CK Dust Collector this section describes assembly and installation of the contents of the Canister Kit SN 708636 Canister Filter 1 Mount the handle onto the canister filter with two M10 hex nuts two M10 flat washers and a M10 lock washer Figure 9 2 Mount the canister filter on top of the collector housing A Fig 5 and tighten the knobs on the canister filter Figure 9 Collector Bag 3 Place the ring over the top of the plastic bag and fold over the bag approximately three inches Figure 10 4 Insert the snap rin
26. to the power source make sure that the switch is initially in the off position on both the dust collector and remote control unit Figure 12 Turning the DC RC230 On amp Off This machine is intended for AWARNING indoor use only 1 Plug the dust collector into the main unit Figure 13 and plug the main unit into the power outlet To start a machine or device 2 Turnthe machine itself on 3 On the main unit place the switch to the ON position Figure 12A The red LED on the main unit should light up 4 Press the button on the remote control transmitter Figure 13 to turn the machine on 5 To stop the machine press the button on the remote control transmitter again Remote Control Transmitter Main Unit Figure 13 When the machine is running it can be stopped by placing the switch on the main unit in the off position Figure 13 To restart repeat steps 3 and 4 Changing Operating Frequency If several devices are controlled by the same type remote control unit each remote control unit can be set to operate at its own unique operating frequency as follows Referring to Figure 14 1 Unplug the DC RC230 Remote Power Control unit 2 Remove the back covers of the main unit A and remote control switch B Locate the switch C in each unit 4 Change the position of the DIP switches in the main unit A to any combination desired as long as they are not the same as other units th
Download Pdf Manuals
Related Search