Lightolier IS:4X4LC User's Manual
Contents
1. EASE SLOT Fig 11 4 7 Remove ballast from mounting plate and install new ballast i 8 Insert wire leads into ballast Follow wiring diagram on FIG 12 BALLAST UPPER 9 Reattach ballast access plate upper reflector lamp s and iat REFLECTOR reflector trim LIC IAT COLTER 5 irpo Road Fali River MA 027202. HOUSING BRACKET HOUSING FIG 1 FIG 2 FIG 3 MOUNTING BAR ordering information For suspended T bar ceilings T bar ANCHOR CLIPS 18 long Cat No 1950 accessory No 1956 order separately may be used with 18 or 27 MOUNTING BARS Fig 4 or simply wire BALLAST MOUNTING BARS EMT TUBING or CHANNELS to ceiling members Fig 5 FIK must be securely attached to and unable to lift from ceiling members after installation is complete WIRE ANCHOR CLIP MOUNTING BAR T BAR FIG 4 FIG 5 For wood joist construction Mounting bars may be used to secure FIK to joists Fig 6 MOUNTING BARS may be bent where required to allow precise placement of FIK between joists Use nails to secure to joists FIG 6 J BOX MOUNTING BAR Note If FIK is to be used with a WALL WASH LOUVER TRIM Fig 7 FIK must be installed with either J BOX side or BALLAST side parallel to wall to be washed lt _______ Direction of wall to be washed A 7 S F G a T LIGHTOLIER LICGHTOLIER A Gilcenor THOMAS COMPANY 631 Airport Road Fall River MA 02720 READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE INSTRUCTION SHEET NO This fixture is intended for installation in accordance with the National Electrical Code and local
3. READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE This fixture is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical inspector before installation To prevent electric shock turn off electricity at fuse box before proceeding Retain these instructions for maintenance reference INSTRUCTION SHEET NO IS 4X4LC A0602 Page 1 of 2 INSTALLATION PROCEDURE FOR 4X4 4X9 AND 9X9 MATRIX SERIES RECESSED DOWNLIGHTS FOR CHICAGO PLENUM A FRAME IN AND WIRE IN Install FRAME IN KIT FIK using ADJUSTABLE MOUNTING BRACKETS Fig s 1 3 Fixture must be secured to structural ceiling members Connect to supply leads white fixture lead to neutral white supply lead black fixture lead to hot supply lead bare copper and or green insulated wire s must be connected to supply ground Use wirenuts local hardware items Place all electrical connections in the J BOX and close cover 3 4 OR 1 1 2 CHANNEL BY OTHERS MOUNTING BAR 1 2 EMT 11 16 OD BY OTHERS ee oc l ADJUSTMENT ADJUSTMENT A ADJUSTMENT ADJUSTABLE SCREW ADJUSTABLE SCREW ADJUSTABLE SCREW MOUNTING FIK MOUNTING FIK MOUNTING FIK BRACKET HOUSING BRACKET
4. SLOT oo 1 Wipe off with a soft clean dry lint free cloth 2 Wipe off with a soft clean cloth dampened in mild detergent solution REFLECTOR Rinse then wipe dry with lint free cloth or paper towel ERUM 3 Wipe off with a clean cloth dampened with a solution of wetting agent and water such as 2 oz Per gallon Pluronic L62 LF by Wyandotte Products FIG 10 Wipe dry 4 Use a liquid wax such as Glass Wax Avoid gritty cleaning agents E RE LAMPING 1 Turn off power PE 2 Pull REFLECTOR TRIM down until ends of TORSION SPRINGS reach EMBOSSED SLOTS 3 Squeeze TORSION SPRINGS to disengage from EMBOSSED a SLOTS and remove REFLECTOR TRIM FIG 11 4 Replace lamp Do not exceed maximum wattage marking S 5 Replace REFLECTOR TRIM MUS care HOUSING F BALLAST REPLACEMENT 1 Make sure AC power is OFF at fuse box 2 Remove reflector trim amp lamp s See E i i Y i 3 Undo wingnut s and remove upper reflector i j l l 4 Remove ballast access plate from housing I Gt l 5 Remove screws that secure ballast to junction box cover pull i st a l Ballast through opening into fixture i 6 Disconnect wire leads from ballast push in terminals AA Insert pin or paper clip in REL
5. regulations To assure full compliance with local codes and regulations check with your local electrical inspector before IS 4X4 LC E installation To prevent electric shock turn off electricity at fuse box before proceeding Retain these instructions for maintenance reference A0602 Page 2 of 2 B ADJUST FIK ADJUSTMENT ADJUSTABLE Set FIK so that bottom edge is flush to or SCREWS recessed 1 8 above finished ceiling Fig 8 MOUNTING BRACKET Pe ra an FIG 9 FIK D Final vertical adjustment may be made by means of FLUSH TO CEILING OR hole pattern Fig 9 to assist with the C CLOSE IN UP TO 1 8 RECESSED alignment of multiple FIK s This hole Siete pattern will facilitate the use of laser Close in and finish ceiling as required CEILING beams plumb lines etc FIG D INSTALLATION OF REFLECTOR TRIM FOR STANDARD AND CHICAGO PLENUM UNITS 1 Squeeze both TORSION SPRINGS and insert ends into EMBOSSED SLOTS 2 Push REFLECTOR TRIM up into FIK until flange is seated firmly against ceiling surface Care and Maintenance of Alzak REFLECTOR TRIM finish If handling of REFLECTOR TRIM with anodized or Alzak finish is required the use of clean white or plastic film gloves is recommended to avoid fingerprints TORSION SPRING Anodized or Alzak surfaces can be cleaned by the following methods
Download Pdf Manuals
Related Search