Lightolier CCLRD01 User's Manual
Contents
1. LIGHTOLIER Architectural Decorative IS C C LR D01 Page 1 of 3 Instruction Sheet for Assembly and Installation Read and understand these instructions before installing luminaire This luminaire control is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical inspector before installation To prevent electrical shock turn off electricity at fuse box before proceeding Retain these instructions for maintenance reference Introduction Color rotary dial control is a digital lighting controller that features eight pre programmed effects plus OFF Effect selection and modification is easy with the rotary knob Push to cycle through the effects and turn to vary the color or speed Color rotary dial control is packaged in an easy to use wall mount assembly Included in this box Color Rotary Dial Control Note Face Plate supplied by others e Color rotary dial control assembly e Knob e 2 6 32 Phillips flat head screws Additional items needed e Single or multi gang wall box e CAT 5 data cable unshielded twisted pair flying lead RJ 45 e 18 AWG power cable with flying leads or 18 AWG power cable with BNC connector and coupling Refer to the wiring diagrams to deter mine your installation requirement e Face Plate Lightolier is a Philips group brand Identification and Warnings2. and user to install maintain and operate the color rotary dial control in such a manner as to comply with all state and local laws ordinances regula tions and the American National Standard Institute Safety Code 631 Airport Road Fall River MA 02720 e 508 679 8131 Fax 508 674 4710 We reserve the right to change details of design materials and finish www lightolier com 2008 Philips Group A0908 PHILIPS LIGHTOLIER Page 2 of 3 Installation The color rotary dial control shall be installed by a qualified electrician in accordance with NEC and relevant local codes for power supplies with Class 2 outputs Color Rotary Dial Control Back Cc Mounting Holes A mi al Enable Disable COE EEELL DIP Switches Tia actin trad OF bid 2243 63a as Fig 2 Five position H H H H H Modas Mode Selection Terminal Block mo 1 Fixed color ON Enabled OFF Disabled 2 Color wash 3 Rainbow 4 or 5 Rainbow 12 6 Random 7 Random fade 8 White Ground 24VDC Data Shield amp WARNING Ensure that power is off before installing the color rotary dial control Wiring the color rotary dial control refer to Fig 3 wiring diagram 1 Using the 18 AWG power cable connect 24 VDC and ground from power supply to the screw terminal located on the back
3. gh the color sp ights the colors appear to follow Random Color Random Color E ectrum When applied to a group of each other from light to light fect is an abrupt transition of 128 ran o the next in spectrum incremen sive colors have similar values Lightolier is a Philips group domly generated colors at specified intervals Colors jump from one hue ts of at least 25 so no two succes brand Architectural Decorative IS C C LR D01 Instruction Sheet for Assembly and Installation Random Fade Random Color Fade is a smooth transition of 128 ran domly generated colors at specified intervals Colors jump from one hue to the next in spectrum increments of at least 25 so no two succes sive colors have similar values Speed Determines the duration of an Effect In Color Wash Speed is defined as the amount of time which elapses between the initial display of the Starting Color in cycle one and its next display which begins cycle two In Cross Fade Speed is defined as the amount of time which elapses between the initial display of the Starting Color to the display of the Ending Color and back again round trip In Random Color Speed is defined as the amount of time a color is displayed before it jumps to the next color In Variable Color Strobe speed determines how fast the colors advance around the spectrum which in turn affects what color will be flashed at each strobe Stand Alone built in o
4. of Safety Hazards In accordance with ANSI 2535 4 the following system of identifying the severity of the hazards associated with the products is used Danger Imminently hazardous situation which if not avoided will result in death or serious injury Warning Potentially hazardous situation that if not avoided could result in death or serious injury Caution Potentially hazardous situation that if not avoided may result in minor or moderate injury or property damage Warning Ensure that main power supply is off before installing wiring or servicing the color rotary dial control Failure to adhere to these instructions can result in death or serious injury Warning The color rotary dial control must be installed by a qualified professional in accordance with NEC and relevant local codes Failure to comply can result in death serious injury or property damage Warning Do not attempt to install or use the color rotary dial control until you read and understand the installation instructions and safety labels Failure to adhere to these instructions could result in serious injury or property damage Caution Do not modify or alter the color rotary dial control Doing so will void the warranty Caution Color rotary dial control has no user serviceable parts Do not open Doing so will void the warranty Owner User Responsibilities It is the responsibility of the contractor installer purchaser owner
5. of the color rotary dial control 2 Using the CAT 5 data cable connect data from the color rotary dial control power data supply to the screw terminal located on the back of the color rotary dial control To Disable Effects When you receive your color rotary dial control eight light effects are preprogrammed and enabled If you wish to limit the number of effects in the cycle or if you know of effects that you will not use you can disable the them prior to physically installing the color rotary dial control into the wall box e To disable an effect set its corresponding dip switch to OFF 1 Fixed Color Color Wash Chasing Rainbow 4 lights wide Chasing Rainbow 8 lights wide Chasing Rainbow 12 lights wide Random Color Random Fade White oN on Fe SN Lightolier is a Philips group brand Architectural Decorative IS C C LR D01 Instruction Sheet for Assembly and Installation Note Keep in mind that any effects you disable prior to installation can only be re enabled by physically removing the color rotary dial control from the wall box and turning on the appropriate switch Mounting the color rotary dial control Now that you have wired the color rotary dial control and disabled enabled the desired effects you are ready to mount it 1 Using screws provided align the mounting holes to a one gang wall box or a single area of a multi gang wall box and attach 2 Attach face plate 3 Attach knob b
6. r on board Refers to a method of Control Stand Alone means that the unit is controlled by the built in microprocessor thus utilizing on board Effects Stand Alone differs from Networked in that the unit is controlling itself versus taking direction from an external source such as a DMX512 controller 631 Airport Road Fall River MA 02720 e 508 679 8131 e Fax 508 674 4710 We reserve the right to change details of design materials and finish www lightolier com 2008 Philips Group A0908 PHILIPS
7. ting from 1 The effects will appear the same Below is an example of light addressing with 24 lights Sequential Addressing A N 631 Airport Road Fall River MA 02720 e 508 679 8131 Fax 508 674 4710 We reserve the right to change details of design materials and finish www lightolier com 2008 Philips Group A0908 PHILIPS LIGHTOLIER Page 3 of 3 Installation Using RJ45 Connector To Luminaires CCLPS602P Front View CCLRDPS60 PWR SUPPLY 100 240VAC 1A COUPLER CCLPS602P BACK VIEW LHAVNY9 CTSIHS Fig 3 A Glossary of Terms Color Factors The impact of light source colors is determined by the combination of three factors hue saturation and luminance Hue indi cates whether a color looks red orange yellow green blue violet etc Saturation represents how pure a color is and luminance brightness identifies how strong the color is Fixed Color Fixed Color Effect is a static display of one color Color Wash A Color Wash Effect produces a smooth transition in hue progressing through the visible color spectrum red orange yellow green blue indigo violet Cycle Direction The sequence in which colors move through the spec rum red orange yellow green blue indigo violet Chasing Rainbow Chasing Rainbow makes a smooth transition from NHO VIVO G44 IGA 2 1 GNNOYD LHAV NUHO VVC color to color throu
8. y aligning the collar with the rotation shaft and press Operating color rotary dial control Using the color rotary dial control is as simple as pressing and turning Press the dial to cycle through the eight effect modes and OFF Turn the dial to vary the effects n Fixed Color mode turning the dial changes the color While in White mode turning the dial changes the intensity In all other modes turning the dial adjusts the speed Color rotary dial control remembers your set ings and recalls them each time you return to the effect Turn the dial clockwise to increase and counter clockwise to decrease the speed The first three revolutions of the dial varies the speed between pproximately 1 2 second to about 2 minutes After which each click of he dial doubles the speed clock wise or decreases by half counter clock wise When in this range the lights snap to a new color with each click for visual confirmation of changes e3 Note In Chasing Rainbow the speed of a single pass through the color spectrum ranges from 1 2 second to 5 hours After the third rotation of the dial the speed is reduced to the point that color changes are not immediately visible The color rotary dial contro outputs data for light addresses 1 through 60 After the first 12 addresses the data is repeated For installations with more than 12 lights you can either sequentially address the lights past 12 up to 60 or repeat the addresses star
Download Pdf Manuals
Related Search