Life Fitness Squat User's Manual
Contents
1. 20 3 7 11 Of af 33 30 3 i 27 gt 26 Squat Assembly Instructions LOOSELY assemble the PLATFORM FRAME 1 to the TOWER 2 using four M10 X 130mm BOLTS 3 eight 3 8 SAE WASHERS 4 and four M10 NYLOCK NUTS 5 as shown LOOSELY assemble the CENTER BRACE 6 to the PLATFORM FRAME 1 using two M10 X 90mm BOLTS 7 four 3 8 SAE WASHERS 4 and two M10 NYLOCK NUTS 5 as shown LOOSELY assemble the UPRIGHT 8 to the CENTER BRACE 6 using two M10 X 25mm BOLTS 9 two M10 X 90mm BOLTS 7 eight 3 8 SAE WASHERS 4 and four M10 NYLOCK NUTS 5 LOOSELY assemble the UPPER BRACE 10 to the UPRIGHT 8 and TOWER 2 using two M10 X 25mm BOLTS 9 four 3 8 SAE WASHERS 4 and two M10 NYLOCK NUTS 5 at the UPRIGHT and two M10 X 70mm BOLTS 11 four 3 8 SAE WASHERS 4 and two M10 NYLOCK NUTS 5 at the TOWER as shown Tighten all BOLTS and NUTS securely Install the PIVOT SHAFT 12 LONG SPACER 13 two BEARINGS 14 and two SHORT SPACERS 15 into the PIVOT HOUSING A of the WORKARM 16 Assemble the WORKARM 16 to the UPRIGHT 8 using two M10 X 25mm BOLTS 9 and two 3 8 SAE WASHERS 4 as shown Tighten the BOLTS securely 7 Assemble the OUTPUT 17 OUTPUT PLATE 18 and OUTPUT RING 19 using three M10 X 45mm BOLTS 20 and three 3 8 SAE WASHERS 4 as shown Tighten the BOLTS securely 8 Assemble the REAR SHROUD2. 21 and FRONT SHROUD 22 to the TOWER 2 using four M10 X 20mm BOLTS 23 four 3 8 SAE WASH ERS 4 as shown Be sure all tabs along the sides and top of the SHROUDS are fully engaged in the slots located inside the TOWER Tighten the BOLTS securely Do not overtighten the BOLTS 9 Secure the OUTPUT CAM ASSEMBLY B to the TOWER HUB C using one M10 X 25mm BOLTS 9 one 3 8 SAE WASHERS 4 and one PLATE 24 as shown Tighten the BOLT securely IMPORTANT Be sure the OUTPUT CAM ASSEMBLY is oriented as shown before securing it to the TOWER HUB 10 Attach the CAM GUARD 25 to the FRONT SHROUD 22 using two M5 X 10mm PHILLIPS SCREWS 26 Tighten the SCREWS securely Do not overtighten the SCREWS Squat Assembly Instructions 11 12 13 14 15 NOTE Some components have been removed from the illustration for clarity Assemble one M10 HEX JAM NUT 27 onto one end of the CABLE 28 approximately 1 2 Assemble the ROD END BEARING 29 to the same end of the CABLE until it meets the M10 HEX JAM NUT Tighten the HEX JAM NUT securely Loosely assemble the ROD END BEARING 29 of the CABLE 28 to the WORKARM 16 using one M10 X 40mm BOLT 30 SPACER 31 3 8 SAE WASHER 4 and M10 NYLOCK NUT 5 Route the cable over the CAM GUARD 25 and around the OUTPUT CAM ASSEMBLY B Insert the remaining end of the CABLE through the inner hole of the OUTPUT CAM ASSEMBLY Insert the CABLE RETAINING PLATE 32
3. over the end of the CABLE Install two M8 HEX JAM NUTS 33 to the end of the CABLE Tighten the M8 HEX JAM NUTS until the WORKARM begins to move and all push pins still move in and out freely Be sure the M8 HEX JAM NUTS are tight against each other Attach the OUTPUT CAM COVER PLATE 34 to the OUTPUT CAM ASSEMBLY B using three M10 X 45mm BOLTS 20 and three 3 8 SAE WASHERS 4 Place the unit in the inteded place for use and check stability If the unit is not stable the FEET D can be adjusted by inserting or removing sup plied SHIMS 36 To add or remove SHIMS loosen the LEVELING FOOT BOLT E and NUT 5 until the desired SHIM S can be inserted or removed Lightly tighten the BOLT and NUT Do not over tighten the BOLT and NUT 16 Attach the PLATFORM 35 to the PLATFORM FRAME 1 using four M10 X 25mm BOLTS 9 and four 3 8 SAE WASHERS 4 as shown Tighten the BOLT securely 17 Install HOLE PLUGS in all open bolt holes 2006 Life Fitness a division of Brunswick Corporation All rights reserved Life Fitness is a registered trademark of Brunswick Corporation TCSL 6 09 06 8061101 RevA 2
4. Squat Assembly Instructions Squat Assembly Instructions Item Qty Description 1 1 Platform Frame 2 1 Tower 3 4 M10 x 130mm Bolt 4 46 3 8 Hat Washer D 15 M10 Nylock Nut 6 1 Center Brace 4 M10 x 90mm Bolt 8 1 Upright 9 11 M10 x 25mm Bolt 10 1 Upper Brace 11 2 M10 x 70mm Bolt 12 1 Pivot Shaft 13 1 Long Spacer 14 2 Bearing 15 2 Short Spacer 16 1 Workarm 17 1 Output Cam 18 1 Output Plate 19 1 Output Ring 20 6 M10 x 45mm Bolt Tools Required 17mm Wrench Metric Allen Wrench Set Ratchet with 17mm Socket Rubber Mallet Ratchet Extension Phillips Screwdriver Part Number 80201XX 79854XX 3291720 3102514 3242002 80202XX 3251715 80203XX 3251702 80319 3251711 7316508 7330007 3235601 7330001 80204XX 7998501 7998495 7998895 3251706 Item 21 22 23 24 25 26 2 28 29 30 31 32 33 34 35 36 37 38 39 Qty Qj Q2 N fF FF NO p Description Rear Shroud Front Shroud M10 x 20mm Bolt Plate Cam Guard Mb x 10mm Phillips Screw M10 Hex Jam Nut Cable Rod End Bearing M10 x 40mm Bolt opacer Cable Retaining Plate M8 Hex Jam Nut Output Cam Cover Plate Platform Leveling Shim 7 16 Hole Plug 1 Hole Plug Multi language Label Part Number 8024808 8024708 3291701 7322301 8013201 7511503 3236901 8020601 3237901 3251705 7489402 8001801 3247502 7998995 8018200 7893101 3237401 3237403 8047101 23 9
Download Pdf Manuals
Related Search