LG HCS6600 User's Manual
Contents
1. LG HCS6600 CodePlus Series Cable HD Transcoder MPEG 2 Installation amp Setup Guide Warranty Copyright 2010 LG Electronics U S A Inc Part No 206 4119 For Customer Support Service please call 1 888 865 3026 The latest product information and documentation is available online at www LGcommercial com products RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACk NO USER SERVICEABLE PARTS INSIDE REFER TO QUALIFIED SERVICE PERSONNEL ALL CARDS MUST BE INSERTED AND REMOVED BY QUALIFIED SERVICE PERSONNEL ONLY The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO PREVENT FIRE OR SHOCK HAZARDS DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus L appareil ne doit pas tre expos a des gouttements d eau ou des claboussures et de plus qu aucun objet rempli de liquide tel que2. The system will request a configuration cfg file Transfer the new configuration file using Xmodem protocol For example in HyperTerminal select Transfer and then Send File In the Send File window enter or select the appropriate configuration file in the Filename field and select Xmodem in the Protocol field Upon receipt of the configuration file the system will request a package pkg file Transfer the package file using Xmodem protocol This process may take several minutes please be patient When the process is com plete the system will report success or failure of the firmware installation Repeat steps 1 to 4 of this procedure for each HCS6600 card whose firmware you wish to update Upon successful installation s power cycle the system Unplug the power cord of the card frame for 15 seconds then plug it in again 15 Troubleshooting Many problems can be corrected with a simple reset of the Cable TV STB and or the HCS6600 Running the system test on the Cable TV STB receiver can also help you diagnose and solve many common problems If you experience image freezes audio freezes or a blank screen or the system won t respond to a front panel button or remote control key presses try one of these Remove and reinsert the cable access card in the Cable TV STB If your STB has a RESET button press it and then wait for program guide information to be acquired Unplug the power cord
3. CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS TO AVOID DEFEATING THE SAFEGUARDS THAT HAVE BEEN BUILT INTO THIS PRODUCT PLEASE READ AND OBSERVE THE FOLLOWING SAFETY POINTS WHEN INSTALLING AND USING THIS PRODUCT 1 Heed all warnings Follow all instructions Read these instructions 9 Outdoor Use Read all the safety and operating instructions Warning To prevent fire or shock before operating the product hazards do not expose this product Keep these instructions to rain or moisture Retain the safety and operating instructions 10 Wet Location for future reference The apparatus shall not be exposed to drip ping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus 11 Test Equipment In some cases LG has supplied or recom mended the use of test equipment and Adhere to all warnings on the product and in the operating instructions Follow all operating and use instructions Do not use this apparatus near water devices for the setup and testing of the Do not use this product near water or mois equipment The operation and maintenance ture or in an area such as a basement that of test equipment is described in their asso might become flooded ciated instruction manuals Please refer to Clean only with dry cloth these manuals for explicit instructions Unplug this product before cleaning Do not regarding the safe use and handling of the use liquid cleane
4. Service Port using the FTDI TTL USB cable P N TTL 232R 5V AJ e Plug the USB end of the cable into an open USB port on your PC If necessary install the device driver Plug the other end of the cable into the Service Port jack on the HCS6600 front panel 3 Using HyperTerminal or an equivalent terminal emulation program on the PC configure the COM port as follows e Baud 115200 e Data bits 8 e Parity None Stop bits 1 e Flow Control None Then initiate communication with the HCS6600 4 Press Enter to refresh the menu display in the terminal 206 4119 You now have access to the HCS6600 configu ration Main Menu Refer to the following sections for information on user configurable options Disable the Content Advisory Descriptor For legacy systems using LST5600 Set back Box receivers it is necessary to disable the Content Advisory Descriptor in the PMT of the HCS6600 s Transport Stream output All other products will operate normally with the Content Advisory Descriptor enabled The default setting is Content Advisory Descriptor Enabled Note Disabling the Content Advisory Descriptor will disable the Parental Control V Chip feature of all room receiv ers for this channel Use the following procedure if you wish to dis able V Chip 1 Connect your PC to the HCS6600 Service Port and access the Main Menu as described previously 2 With the Main Menu on display type the number c
5. dated bill of sale or delivery ticket as evidence of the purchase date Read the Installation and Setup Guide carefully so that you will understand the operation of the HCS6600 and how to adjust the controls Reception problems caused by inadequate antenna or faulty antenna connections are the owner s responsibility For warranty service information call 1 888 865 3026 Parts and service labor that are LG s responsibility see above will be provided without charge Other service is at the owner s expense If you have any problem in obtaining satisfactory warranty service call 1 888 865 3026 You must provide the model number serial number and date of purchase or date of original installation For Customer Support Service please call 1 888 865 3026 www LGcommercial com CodePlus is a trademark of LG Electronics U S A Inc All other trademarks or registered trademarks are the property of their respective owners 206 4119 Copyright 2010 LG Electronics U S A Inc Revision A
6. des vases ne doit tre plac sur l appareil REGULATORY INFORMATION This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communica tions Operation of this equipment in a residential area is likely to cause harmful interference in which case the user should be required to correct the interference at his own expense CAUTION Do not attempt to modify this product in any way without written authorization from LG Electronics U S A Inc Unauthorized modification could void the user s authority to operate this product COMPLIANCE The responsible party for this product s compliance is LG Electronics U S A Inc 2000 Millbrook Drive Lincolnshire IL 60069 USA Phone 1 847 941 8000 Marketed and Distributed in the United States by LG Electronics U S A Inc 2000 Millbrook Drive Lincolnshire IL 60069 2 Copyright 2010 LG Electronics U S A Inc 206 4119 IMPORTANT SAFETY INSTRUCTIONS Important safeguards for you and your new product THIS PRODUCT HAS BEEN MANUFACTURED AND TESTED WITH SAFETY IN MIND IMPROPER USE HOWEVER
7. in a card frame return the HCS6600 card to the anti static bag in which it was shipped Note The CodePlus series products are NOT designed to be hot swappable Power must be removed to the card frame before any CodePlus transcoder cards are inserted or removed Note The card slots in the card frame are NOT all identical An HCS6600 card can only be installed in Slots 1 to 6 and 7 to 12 The CONTROLLER slot between Slots 6 and 7 is dedicated for optional feature cards and is not compatible with HCS6600 cards Note When installing cards remove blank cover plates and insert new cards as applicable For ports that will not be used leave the blank cover plates in place for proper ventilation and FCC and safety agency compliance 206 4119 CONTROLLER Slot The card in this slot may vary depending on system features 1 Unpack the HCS6600 unit s and all accessories Accessories provided IEEE 1394 Cable Length 1 meter Select the slot s in the card frame in which to install the HCS6600 Note All cards must be used in an LG approved card frame for this product Remove the AC power cord for the card frame from the power outlet Remove the blank cover plate from each slot into which a card is to be inserted Without using force slide each new card into its designated slot and ensure that it is fully inserted Engage and tighten the top and bottom thumbscrews securely Note that the thumb scre
8. of the STB for 15 seconds then plug it in again Press the RESET button on the HCS6600 card to reboot it Unplug the power cord of the CodePlus card frame for 15 seconds then plug it in again Equipment Setup Review Make sure all connectors and connections are tight and secure on all entertainment system components Check the IEEE 1394 connection Ensure that the access card is installed is up to date and has been authorized by the Cable Service provider Check that the batteries in the remote control are fresh and that the remote mode selector switch is set on CATV Note that only one Cable TV STB should be ON at a time Status LED The green Status LED on the HCS6600 front panel provides general information about the operating condition of the transcoder Observe the Status LED and refer to the following table Status LED Behavior Operating Status Slow Blinking System Booting Rapid Blinking Ready for Input Continuously On Normal Operation Continuously Off Fault Condition No Output 1 6 206 4119 Specifications Dimensions Height 3U 130 20 mm Width 1 102362 inches 28 00 mm Depth 9 055118 inches 230 00 mm Weight 0 485016 pounds 0 22 kgrms Est Environmental Storage Conditions Temperature 20 to 70 degrees Celsius 4 to 158 degrees Fahrenheit Humidity 95 non condensing Environmental Operating Conditions Temperature 0 to 40 degrees Celsius 32 to 104
9. CodePlus series of transcoder cards Pairing an HCS6600 card in the appropriate CodePlus card frame with a suitable Cable TV STB receiver will provide one chan nel of Cable TV content Features e Part of modular system easily scaled for each application e Transcodes Cable DTV content to ATSC compatible MPEG 2 Built in Pro Idiom content protection e DVB ASI output available to connect to external MUX or modulator e Transcoded output supports Closed Captions and V Chip Parental Control e Short 3U height profile to minimize rack space usage If included in the signal source 6 206 4119 Transcoder Product Description Typical Cable HD Transcoder System Overview The LG HCS6600 Cable HD transcoder represents a single channel HDTV solution for commercial and institutional MATV systems hotels hospitals etc A typical Cable HD Transcoder system includes e An HCS6600 Cable HD transcoder for each HD program offered in the commercial facility MATV system e A CodePlus series card frame Example HCS6100R specified for the HCS6600 Purchased separately Cable TV service feed Cable TV STB receiver for each transcoder HD program VSB or QAM modulator with ASI input for each transcoder or LG CodePlus series unique feature card Example HCS6300 Multiplexers can be used in front of the modulator if multiple programs are desired and 256 QAM is used For each modulator if applicable Upconverter compatible
10. anted for the remaining portion of the original warranty period Warranty service is provided at LG Customer pays for shipping charges to LG LG pays for return shipping charges to return HCS6600 to customer Call 1 888 865 3026 for further information This warranty covers manufacturing defects and does not cover installation adjustment of customer controls installation or repair of antenna systems cable converters or cable company supplied equipment it also does not cover damage due to misuse abuse negligence acts of God or other causes beyond the control of LG Any alteration of the product after man ufacture voids this warranty in its entirety This warranty does not cover any missing or stolen access cards THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND LG SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL INDIRECT OR INCIDENTAL DAMAGES OF ANY KIND INCLUDING LOST REVENUES OR PROFITS IN CONNECTION WITH THIS PRODUCT SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU OWNER S RESPONSIBILITY Effective Warranty Date Installation Guide Antenna Warranty Service Warranty begins on the date of delivery of the HCS6600 For your convenience keep the dealer s
11. controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation d If the product has been dropped or the cabinet has been damaged e If the product exhibits a distinct change in performance Caution Refer all servicing to qualified service personnel 14 Servicing Caution These servicing instruc A tions are for use by qualified service personnel only To reduce the risk of electrical shock do not per form any servicing other than that described in the operating instructions unless you are qualified to do so 15 Safety Check Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition 206 4119 Table of Contents Setup Information Table of Contents Safety Warnings 2 Important Safety Instructions 3 4 Table of Contents Setup Information 5 HCS6600 Product Description 6 Transcoder Product Description 7 Card Description 8 Installing CodePlus Transcoder Cards 9 Cable TV STB Receiver amp HCS6600 Initialization amp Setup Connections 10 System Setup 11 12 Configuration Options 13 15 Troubleshooting 16 Specifications 17 Documen
12. degrees Fahrenheit Humidity 95 non condensing Electrical DC Input 12V DC 0 4 Amps Impedance at ASI Out jack 75 Ohms Active Output Level at ASI Out jack 800 mv IEEE 1394 Input IEEE 1394a 2000 Note Design and specifications subject to change without prior notice 206 4119 17 Document Revision History Notes Document Revision History Date Description February 2010 Revision A New Document Product documentation is available online at www LGcommercial com products From the Products page select Head End Systems then CodePlus Transcoder Series then Cable TV Modular Systems then the applicable CodePlus series card frame then HCS6600 Click the Downloads amp Images tab on the HCS6600 page and select the required document from the Downloads list Notes 18 206 4119 LG HCS6600 Cable Transcoder Warranty Broadcast Products Welcome to the LG family We believe that you will be pleased with your new HCS6600 Cable TV Transcoder Please read this warranty carefully it is a LIMITED WARRANTY as defined under Federal Law This warranty gives you specific legal rights and you may also have other rights that vary from state to state within the U S A LG s RESPONSIBILITY Warranty Term Parts Warranty Service Not Covered One year parts and labor from date of purchase or delivery date New or remanufactured replacements for factory defective parts may be used Such replacement parts are warr
13. e the IEEE 1394A port for the Cable TV STB connection ASI Out DTV signal output Retaining Screw Install after inserting HCS6600 card 206 4119 Installing CodePlus Transcoder Cards CONTROLLER Slot HCS6600 x Sota _ slota SR slots slots Slot Slot8 Slot9 Slot10 Slot11 Slot 12 HCS6600 HCS6600 Hcs6600 Hcs6300 Hcs6600 Hcs oo Hcs6600 Hcs6600 T Hcs6600 Hcs 6o0 SERVICE PORT Osme LES save sva sme Osave sme Osma 4 O RESET PORT PORT PORT PORT PORT PORT PORT x O reser O reser O reser O reser O reser O reser O reser ee O status Osmus Osm O sms Osu O sms Osm Osmu ce 1 am E 5 5 5 G G Ae 3 E 3 9 9 9 3 9 fo AU Ef I es l s l s l s l es l oe ES nT i i i i ii n ss E E E E ee EU EU EU EU EU EU EU E3 x A FN IN A IN AN FN f o 0 0 0 6 01 6010 f SZ A a SZ fi SZ a SF q LI A SZ a Ss A G ASI OUT G e L ASI OUT G ASIOUT G ASIBUT G ASI OUT G asiour G ASIOUT AD Note All cards used in the card frame must be inserted and removed by qualified service personnel only Note Use extreme care when handling an HCS6600 card Always observe proper precautions with respect to static electric ity and mechanical shock When not installed
14. fo option and press Enter The system will display a System Information banner that contains important information about the HCS6600 including the unit serial num ber hardware ID firmware version and software version LG suggests that you record this infor mation for future reference If you find it neces sary to call customer service or engineering sup port please have this information available Reset the HCS6600 Use the following procedure if you wish to reset the HCS6600 1 Connect your PC to the HCS6600 Service Port and access the Main Menu as described previously 2 With the Main Menu on display type the number corresponding to the Reset option and press Enter The system resets the HCS6600 During the reset process several pages of status and diag nostic messages may be displayed After reset the HCS6600 resumes normal operation and the system displays the System Information ban ner and Main Menu Update HCS6600 Firmware Use the following procedure if you wish to update HCS6600 firmware Note If you are not sure of the current firmware version LG recommends that you view and record the System Information see procedure above before you initiate the firmware update 206 4119 Connect your PC to the HCS6600 Service Port and access the Main Menu as described previously With the Main Menu on display type the number corresponding to the Update Firmware option and press Enter
15. l be stored in non volatile storage regardless of pro cess results 14 Note The process of updating the encryption key will synchronize the decryption key in any receiver tuned to this card s output If the target receiver is turned off or viewing a different card the synchroni zation will not occur and the output will be scrambled Ensure that all encrypters and decrypters in a system are synchronized to the same key View the Pro ldiom Key Checksum Use the following procedure if you wish to dis play the Pro ldiom Key checksum 1 Connect your PC to the HCS6600 Service Port and access the Main Menu as described previously 2 With the Main Menu on display type the num ber corresponding to the Read PI Key Checksum option and press Enter The system will display the following PI key checksum is XXXXXXXXXX where xxxxxxxxxx identifies the set of Pro Idiom Key files installed on the transcoder Note All transcoder cards in the card frame must have the same Pro ldiom Key files installed View System Information Use the following procedure if you wish to dis play system data including HCS6600 hardware and software information 1 Connect your PC to the HCS6600 Service Port and access the Main Menu as described previously Continued on next page 206 4119 Configuration Options Cont Continued from previous page 2 With the Main Menu on display type the number corresponding to the System In
16. n the Cable TV STB and the HCS6600 IEEE 1394A port Perform one of the following per your installation If the HCS6600 will NOT be used with a unique feature card in the card frame CONTROLLER slot connect a 75 ohm BNC to BNC coaxial cable between ASI OUT on the transcoder and ASI IN on the modulator Then continue with step 5 Note The BNC cable must be less than 30 feet 9 2 meters in length If the HCS6600 will be used with a unique feature card in the CONTROLLER slot the cable to the ASI OUT port may not be required Refer to the Installation amp Setup Guide for the feature card for further instruc tion before you continue this setup procedure 206 4119 5 If your installation includes a separate modula tor and upconverter connect an RF coaxial cable between IF OUT on the modulator and IF IN on the upconverter and then check the modulator and upconverter for correct settings QAM type channel number etc Repeat steps 1 to 5 for each of the Cable TV STB transcoder pairs Plug in power to the CodePlus card frame containing the newly installed HCS6600 card s The green Status LED will blink at an approximately 1 Hz rate while the HCS6600 card boots up The boot up process for an HCS6600 may take up to two minutes and there is no ASI output if applicable during boot up When the boot up is complete the green Status LED will be lit continuously If applicable connect the RF output o
17. n the upconverter to the combiner Check one or more room receivers to make sure all channels are properly tuned mapped and operating 11 System Setup Cont Typical Setup Flow Chart for a Single HD Channel Cable TV Service Feed RF Cable Cable TV STB AN 1394 Out 1394 In Cables for monitor only HCS6600 Combiner NTSC VSB or QAM DTV Monitor Modulator Upconverter Note This diagram shows setup connections where a unique feature card is NOT installed in the card frame CONTROLLER slot 12 206 4119 Configuration Options The HCS6600 contains several internal registers for different configuration options These can either be left at their default values or configured by the user There are two methods available for configuration purposes e Service Port Method Controller Card Method This document describes configuration procedures using the Service Port Method which requires that you connect a PC directly to the transcoder Service Port For configuration procedures using the Controller Card Method refer to the Installation amp Setup Guide for the feature card installed in the card frame CONTROLLER slot Connect a PC to the HCS6600 Service Port and Access the HCS6600 Main Menu 1 Follow the directions in the Installation and Test sections of this manual The Cable TV STB and the HCS6600 must be installed and operating before you proceed 2 Connect the PC to the HCS6600
18. orresponding to the Toggle Content Advisory option and press Enter The system will print out the new state of the Content Advisory Descriptor option This state will be stored in non volatile storage and remain in that state until changed by a user 13 Configuration Options Cont Change or Renew the Pro ldiom Encryption Key The Pro ldiom encrypter built into the HCS6600 contains a default encryption key When first installed the HCS6600 will use this key to encrypt content Note In order for a Pro ldiom encrypted channel to be displayed the following conditions are required The receiver must contain a Pro ldiom decrypter The MPI control card in the receiver must be configured to allow decryption of the desired channel If it becomes necessary to change or renew the encryption key use the following procedure 1 Connect your PC to the HCS6600 Service Port and access the Main Menu as described previously 2 With the Main Menu on display type the number corresponding to the Setup PI option and press Enter 3 The system will request a key file Transfer the new Pro ldiom key file using Xmodem protocol For example in HyperTerminal select Transfer and then Send File In the Send File window enter or select the appropriate Pro ldiom key file in the Filename field and select Xmodem in the Protocol field The system will then print out the result of the update process Note that the new key wil
19. rs or aerosol cleaners equipment Refer all servicing to qualified service per 12 Replacement Parts sonnel When replacement parts are required be Servicing is required when the apparatus has sure the service technician uses replace been damaged in any way liquid has been ment parts specified by the manufacturer or spilled or objects have fallen into the appara that have the same characteristics as the tus the apparatus has been exposed to rain original parts Unauthorized substitutions or moisture does not operate normally or may result in fire electric shock or other has been dropped hazards Object and Liquid Entry Never push objects of any kind into this prod uct through openings as they may touch dan gerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product Continued on next page 206 4119 3 IMPORTANT SAFETY INSTRUCTIONS Continued from previous page 13 Damage Requiring Service Unplug this product from the wall power out let and refer servicing to qualified service personnel under the following conditions a If liquid has been spilled or objects have fallen into the product b If the product has been exposed to rain or water c If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other
20. t Revision History Notes 18 Warranty Back Cover Setup Information This document provides installation and setup support only for an HCS6600 transcoder card Cable TV service and a Cable TV STB receiver must be installed and operating before you can proceed to set up the HCS6600 LG recommends that the system be professionally installed Check the items listed below before you begin the HCS6600 installation and setup procedures Cable Set top Box STB Refer to the documentation provided with the Cable TV STB and carefully follow the sys tem setup procedures The Cable TV STB receiver provides the IEEE 1394 signal input for the HCS6600 Authorization is required for HD channels Contact your local Cable TV provider to get subscription programming authorization for the Cable TV STB receiver ASI Output Optional __ If applicable install the DTV modulator and upconverter that will receive the ASI output signal from the HCS6600 Refer to the man ufacturer s documentation 206 4119 HCS6600 If the HCS6600 will be used with a unique feature card Example HCS6300 in the card frame CONTROLLER slot you will also need a copy of the Installation amp Setup Guide for the feature card in order to com plete the HCS6600 system setup For HCS6600 Service Port connections you must use an FTDI TTL USB cable P N TTL 232R 5V AJ HCS6600 Product Description The HCS6600 is one of the LG
21. with digital modulation 19 inch rack for mounting Miscellaneous cables and installation hardware see also HCS6600 setup information on page 5 The elements of such a system combined can e Receive a selected HD channel from Cable TV service using a Cable TV STB receiver e Transcode the digital video and audio stream to an ATSC A 53E compatible transport stream e Encrypt the received digital data stream e Modulate the stream in 64 QAM or multiplexed 256 QAM A Pro ldiom compatible television with a QAM VSB tuner is required to view premium HD content The HCS6600 changes the Cable TV encryption scheme to a Pro ldiom encryption scheme A proper session ID must be set at the TV in order for Pro ldiom decryption to be enabled LG s Pay Per View PPV partners can properly set up this session through their interface An LG Free to Guest FTG card is substituted for the supplied Multiple Protocol Interface MPI card and can set the session to allow decryption Note Design and specifications subject to change without prior notice 206 4119 7 Card Description HCS6600 Service Port TTL USB serial port connection use FTDI TTL 232R 5V AJ cable Reset Reboots card Status Blinking pattern indicates condition of card SERVICE PORT O RESET status Retaining Screw Install after inserting HCS6600 card IEEE 1394 In To Cable TV STB 1394 Out Note Always us
22. ws should only be finger tight overtighten ing may damage the assembly Refer to the diagram on page 10 for cable connections and complete the system instal lation and test procedure on page 11 Cable TV STB Receiver amp HCS6600 Initialization amp Setup Connections RF Feed Laptop abie TY from Cable TV C Power Outlet as Provider Ke 120V 60Hz AC TTL USB Q Service Port Connection Composite HCS6600 Video In Card Frame and L R Audio 1394 Chassis to NTSC Monitor Link ASI Out Pead Power Outlet o 120V 60Hz AC oe oo LA on RF Distribution ot Grid SCeiver Modulator Eceiy Combiner WS Upconverter Room Receive Note This diagram shows setup connections Room where a unique feature card is NOT installed Receive in the card frame CONTROLLER slot 10 206 4119 System Setup Typical HCS6600 System Installation amp Test see also Typical Setup Flow Chart on page 12 1 Verify that the Cable TV STB receiver is set up and functioning i e check that the STB is connected to an NTSC monitor for tuning pur poses that it is powered up that initialization is complete and that the NTSC monitor is displaying the default channel properly refer to the STB documentation On the Cable TV STB tune to the appropri ate channel using the controls on the front panel or the IR remote control Connect the IEEE 1394 cable betwee
Download Pdf Manuals
Related Search