Lenco DF-831 User's Manual
Contents
1. enco DF 831 8 Digital photo frame User manual For information and support www lenco eu 1 Getting started Checking the appearance Sensor for remote control OOOOOOD 2 Understanding interface and on board buttons Om Om OT A A Q3 1 NO or 6 Menu Back Confirm Down Up Right Left 7 On Off 8 mini USB port 9 USB port 0 SD MMC reader 1 Sockets for AC power adaptor 12 Frame stand port 3 Installing and recharging your unit Open the package and remove the protective sleeve from the unit Screw in the stand to the stand screw hole on the back of the photo frame Adjust the frame position for vertical or horizontal placement Plug in the AC adapter into power outlet Plug the other end into the unit Insert your memory card and the unit starts the slideshow digital photos automatically 4 Understanding the remote Power On OFF Clock Calendar GO up Go Left Previous Picture Confirm Go Right Zoom in out 9 Go Down 10 Rotate 11 Exit go to previous menu 12 Slideshow 13 Setup d HORO OOY Understanding the MENU 1 Function Navigation Power on the unit the unit will display the following menu if there is no card inserted ro Devices Calendar Figure 1 You can use the function navigation above to change all aspects of your photo frame from the trans2. it is highly recommended to restor to factory default Figure 12 select Default then select Yes all the changed settings will be restored to factory default Trouble shooting Symptom Corrective Actions Digital Picture Frame The POWER connector to Make sure you connect the AC doesn t power on the unit is not securely adapter to the frame properly and inserted make sure you have powered on the unit by using the On Off button When you connect the AC adapter to the frame and power up the unit even without a memory card you should see a blank screen If you don t see the lit screen check if the power is connected to the Digital Picture Frame and make sure it is securely attached No Start up screen Memory card is not Insert a Supported memory card inserted correctly No photo on the Card is wrongly inserted Verify if the way you inserted the memory card card is correct Make sure the front label of the memory card is facing AWAY from you Do not force the memory card into the slot The File doesnt play Incompatible File Format Make sure there is at least one supported photo file on the memory card Compatible Photo format JPEG This symbol indicates that the relevant electrical product or battery should not be disposed of as general household waste in Europe To ensure the correct waste treatment of the product and battery please dispose them in accordance to any applicable local laws of requirement for dispo
3. itions sytle of your slideshows to the colour balance of the display To bring up the menu on screen just press the MENU button on board or the ESC button on the remote to go to the above interface 2 Playing photos DASQHO011 JPG 2010 11 19 Figure 2 Figure 3 You can slideshow the photos one by one Figure 2 or display in thumbnail mode Figure 3 3 Select the media source Devices Calendar j INTERNAL Figure 4 Figure 5 Select Device to show the media source there are 3 media sources including internal memory SD card and USB drive Figure 5 If both of SD card and USB drive are inserted please select the media source first 4 Display Clock Calendar Figure 6 Figure 7 Select Calendar from the function navigation menu shown in Figure 1 the calendar amp clock window will be displayed the frame can display a sub window to slideshow photos as shown in Figure 6 or you can bring up a analogue clock to the screen as shown under Figure 7 5 System setup To enable some customized features please configure the frame via system setup as below a Photo Setup Photo Setup Display Mode l Browse Mode DELETAR Crop to Fill Slide show time 15Min Slideshow Repeat Repeat Transition effect Erase Figure 8 Under Photo Setup you can configure Display model Display Ratio Slideshow Interval slideshow repeat as well as transition effect Navigate with Left Right button to change the optio
4. ns use Up Down to switch between menus b Calendar Setup Calendar Setup Display Mode Analog Clock Set Date 12 08 2009 Clock Mode 24hr Figure 9 As shown in Figure 9 you can configure Display mode Analog Colck Digital Clock set the right date Change the clock mode from 24hr to 12hr or vice versa change the current time settings Navigate with Left Right button to change the options use Up Down to increase decrease the numbers c System setup System setup Language English Backlight 5 Brightness 3 Contrast 3 Saturation 3 Auto Boot Time 00 00 Power Off Off System setup Saturation Power On Auto Boot Time Power Off Auto Shut Time Auto Power Frequen Everyday Default Figure 10 Figure 11 1 Language As show in Figure 10 select language menu you can change the language with left right buttons 2 Auto power On Off To enable power on off firstly please select On to enable power On Power Off as shown respectively in Figure 10 amp Figure 11 then set time for auto power on power off Use left right or Up Down buttons to change the numbers and menus 3 Reset to factory default System setup Auto Boot Time Power Off Auto Shut 7 Auto Powe Default Ver RCP 4080V1 1 system Upgrade ios Figure 12 The factory default settings include the optimized configurations for consumers in case that there is any malfunction or some features can not function as expected
5. sal of electrical equipment or batteries In so doing you will help to conserve natural resources and improve standards of environmental protection in treatment and disposal of electrical waste Waste Electrical and Electronic Equipment Directive
Download Pdf Manuals
Related Search