Land Pride Snow Plow User's Manual
Contents
1. 26 07 8 Manual i 57M Land Pride Assembly Instructions Kit No 823 227C NT MOUNT KIT SNOW PLOW item Part No Part Description Qty 1 CYC4598 BLADE MOUNT 2 PUR1209 3 8 CLEVIS PIN 3 805 010c RPBY 805 010C 4 PUR1415 3 8 X 1 1 2 X 2 1 2 U BOLT 5 PUR1435 5 16 X 2 X 3 U BOLT 6 804 011C WASHER FLAT 3 8 USS PLT 7 804 078C WASHER INTERNAL STAR 3 8 PLT 803 078C NUT LOCK 3 8 16 NYLON INSERT 803 094C NUT 5 8 11 NYLON COLLAR THIN Fi 823 2270 3 8 06 26 07 Manu I 1577M 9 Corporate Office PO Box 5060 Salina Kansas 67402 5060 USA www landpride com2. 823 226C A WARNING Due to reduced ground clearance remove plow Mount Brackets before trail riding Do not exceed 5 MPH with the blade or its brackets installed OPERATION TIPS When plowing snow or dirt into a pile back away from the pile before attempting to raise the blade For best results set the suspension to the stiffest setting if possible The Blade is shipped with the Blade Skids mounted upside down for boxing Be sure to mount the Skids properly before using your blade MAINTENANCE Periodically check for wear and tightness of all bolts nuts and fasteners Replace or tighten as necessary Grease all pivot points and hinges as needed NOTICE The use of Winch Mounting Kits Not Manufactured by Land Pride Accessories with Work Power Blades will void all warranties The Winch Kits are specifically designed to help prevent damage to the Blades Winch Kits and the Machine All directions referring to the right and the left are when the operator is sitting on the machine Blade Connection To secure the Blade to the Blade Hinge 2 Place the Steel Bushings 9 into the holes in the Blade Hinge 2 Using the Top holes in the Blade Secure the Blade 2 Manual No 701 157M m 06 26 07 Assembly Instructions Land Pride Hinge 2 to the Blade with the 1 2 x 1 Bolts and Locknuts 15 Tighten Nuts to 60 Ft Pounds of Torque See diagram below Remove the two Blade Spring Attaching B
3. LADE HEIGHT LOWER BLADE TO THE DOWN POSITION 7 WHEN BLADE IS NOTIN USE STOP ATV ENGINE SET AND LOCK BRAKES AND LOWER BLADE TO DOWN POSITION OPERATION Your blade and hardware were designed with your safety in mind In order to protect you and your machine certain parts of the blade and or hardware are designed to fail when the equipment is over stressed For this reason Push Tubes Blade Hinges Foot Peg Brackets Push Plate Attaching Pins and Clevis Pins are not covered by Warranty Blade angle is adjustable Lock blade in the up position To move the blade left right or straight pull the Blade Copyright 2007 Printed 06 26 07 Assembly Instructions Land Pride Position Lever ahead and turn the blade to the desired position The Lever will spring back when the blade is at the correct angle The blade skids are adjustable so the blade can be lowered but still held a certain distance off the ground The blade is designed to trip when it strikes an object or digs in too far When pressure is released the blade springs back into position Blade spring tension may be set stiffer by tightening the Locknuts on the bottom of the Eyebolts For less spring tension loosen the Locknuts Do not exceed 5 MPH with blade installed Operate with extreme caution on slopes steep grades and rough terrain Keep away from blade and moving parts during operation When plowing snow or dirt into a pile start ba
4. RMS FOR SNOW PLOW item Part No Part Description Qty 823 226C PUSH ARMS FOR SNOW PLOW 1 CYC3154 Y2K PUSH TUBE 1 2 CYC2389 BLADE HINGE 1 3 CYC0345 BLADE POSITION LEVER BRACKET 1 4 CYC0813 ADJUSTABLE BLADE STOPS 2 5 CYC2259 BLADE POSITION LEVER 1 6 PUR1437 SPRING 1 7 PUR1361 SLEEVE BUSHING 2 8 CYC0812 BLADE SPRING BRACKETS 2 9 PUR1411 7 8 STEEL BUSHING 2 10 802 079C HHCS 3 8 16X1 1 4 GR5 2 11 803 155C NUT LT JAM 1 1 4 12 NYLN INSRT 1 12 802 138C HHCS 5 16 18X2 1 4 GR5 1 13 802 159C HHCS 5 16 18X1 GR5 2 14 PUR1216 5 16 X 4 1 4 EYE BOLT 2 15 802 091C HHCS 1 2 13X1 1 2 GR5 2 16 803 019C NUT LOCK 1 2 13 PLT 2 17 PUR1409 BLADE SPRING 2 18 U610 1 3 8 END CAP 2 19 SNATCH BLOCK ASSEMBLY 1 4 D po D g 10 4 i b i A e 5 P i if Pai 19 jiz va L4 i i gig I le X 13 H 17 i 11 a V E 06 26 07 Manu W 157M 7 Land Pride Assembly Instructions Kit No 823 230C ST MOUNT KIT SNOW PLOW item Part No Part Description Qty 1 CYC4610 BLADE MOUNT 2 PUR1209 3 8 CLEVIS PIN 3 805 010C PIN HAIR COTTER 094 4 PUR1415 3 8 X 1 1 2 X 2 1 2 U BOLT 5 PUR1435 5 16 X 2 X 3 U BOLT 6 804 011C WASHER FLAT 3 8 USS PLT 7 804 010C WASHER FLAT 5 16 USS PLT 803 078C NUT LOCK 3 8 16 NYLON INSERT 803 084C NUT HEX NYLOCK 5 16 18 PL R a fa f m D i wA H NJ j l i KE ha na i p f N ha 1 u 1 R he ha e ha ha Sa k o TO pp 823 230C A JE A 06
5. Snow Plow Assembl Instructions Treker NT amp ST Series Before You Start When you see this symbol the subsequent A instructions and warnings are serious follow without exception Your life and the lives of others depend on it IMPORTANT Before you begin read these instructions and check to be sure all parts and tools are accounted for Please retain these installation instructions for future reference and parts ordering information Your Snow Plow is exclusively designed for your Land Pride NT amp ST Treker Please read these installation instructions and your NT amp ST Treker Operator s Manual thoroughly before beginning Especially read information relating to safety concerns Also included in the Operator s Manual is important information on operation adjustment troubleshooting and maintenance for this attachment Some manual sections do not apply to all accessories General Information These assembly instructions apply to the following Snow Plow Accessories listed below 701 067A NT 60 SNOW PLOW 701 068A ST 60 SNOW PLOW Further Assistance Your dealer wants you to be satisfied with your new Snow Plow If for any reason you do not understand any part of this manual or are not satisfied with the service received the following actions are suggested 1 Discuss the matter with your dealership service manager making sure he is aware of any problems you may have and that he ha
6. cking up before raising the blade Do not ram the blade into the pile SLOW DOWN BEFORE HITTING THE PILE Be aware of possible hidden objects under snow Wear head protection safety glasses and shoes as recommended in the machine s Operators Manual Allow no riders on blade or machine while moving or stationary Keep bystanders away from blade and machine while moving or stationary When blade is not in use stop the machine s engine set and lock brakes and lower blade to down position Only mature adults over the age of 16 should operate the machinery Do not operate this machinery if you are under the age of 16 Please read and follow all of the instructions in the owner s manual Please read and follow all of the instructions in the machine s operations manual Keep all bystanders a minimum of 15 Meters away from the machine and Blade when it is in operation Do not use this equipment at night in the dark or under poor weather conditions unless your machine has adequate lighting which produces clear safe vision Due to the extra length of the 60 1 52 M Blade loss of directional control may result when pushing heavy material Use with Caution Assembly Instructions A detailed listing of parts for this accessory kit is provided on page 6 Use the list as a checklist to inventory parts received Please contact your local Land Pride dealer for any missing hardware UNIVERSAL PUSH TUBE Part No
7. fere with the normal use of the blade system Attach the Lift Strap 6 to the top of the brush guard Hook the winch hook onto the Lift Strap 6 Snatch Block parts list T gt sain EI tais ole z wHMal noch Bock iiras i Ia T IS r m R Lu rule ira 18 ZEN ocking Fi 1 UISI2P U Shox s CP Pla M Srch Block i Winch ya PLOW MOUNT JA i 1 Attach 1 Blade Mount to bottom of frame tubes YR o Shown above using the 5 5 16 x 2 x 3 U Bolts for p the rear and the 4 3 8 x 1 1 2 x 2 1 2 U Bolts for the front Figure A 4 Manual No 701 157M M 06 26 07 Land Pride Assembly Instructions 823 227C NT MOUNT KIT SNOW PLOW W INST PLOW MOUNT 1 Attach 1 Blade Mount to bottom of frame tubes Shown above using the 5 5 16 x 2 x 3 U Bolts for the rear and the 4 3 8 x 1 1 2 x 2 1 2U Bolts for the front 06 26 07 E Manual No 701 157M 5 Land Pride Listing of Parts Kit No 823 224C 60 STEEL SNOW PLOW Item Part No Part Description Qty 1 823 224C 60 STEEL SNOW PLOW 1 2 802 282C RHSNB 5 16 18X1 GR5 9 2 803 084C NUT HEX NYLOCK 5 16 18 PLT 9 3 PUR0400 5 8 X 1 SPACER 4 4 805 240C PIN LINCH 3 16 X 1 9 16 LONG 2 5 CYC0790 60 WEAR BAR METAL Optional 1 5 PUR1494 60 WEAR BAR PLASTIC Optional 1 6 804 021C WASHER FLAT 5 8 SAE PLT 12 7 PUR1467 H D SKID 2 6 Manual No 701 157M m 06 26 07 Assembly Instructions Land Pride Kit No 823 226C PUSH A
8. rackets 8 from the LEFT side of the Blade Hinge Fasten one on either side of the Blade Hinge as shown in the parts breakdown and picture Hang the two Blade Springs 16 from the top holes in the Blades ribs Place the Eyebolts 14 onto the springs and fasten the Eyebolts to the Blade Spring Attaching Brackets 8 using the two locknuts Spring tension may be set stiffer by tightening the locknuts on the Eyebolts or for less tension loosen the Locknuts Setting the tension stiffer means the blade will not trip as easily as when set with less tension Both Hushengs sb il Same Sk a Install the Blade Position Lever 5 and Blade Position Spring using the 5 16 x 2 1 4 Bolt 12 Roller Bushings and 5 16 Nylock Locknut provided See picture above Tighten bolt fully and THEN LOOSEN JUST ENOUGH TO ALLOW THE BLADE POSITION LEVER TO MOVE FREELY Both Roller Bushings on the LEFT side These Instructions are for the Push Tube Assembly only Final Blade Installation Position the Push Tube Assembly 1 under the machine Lift the rear of the assembly up and secure it to the Push Tube Attaching Brackets using the 3 8 Clevis Pins and 3 Hairpins provided in the Attaching Kit The Blade Stops 4 on either side of the Blade Hinge are shipped loose By turning the Stops around the pitch of the Blade changes The recommended pitch is one that allows the top and bottom of the blade to be perpendicular to the ground Se
9. s had the opportunity to assist you 2 If you are still not satisfied seek out the owner or general manager of the dealership explain the problem and request assistance 3 For further assistance write to Land Pride Service Department 1525 East North Street P O Box 5060 Salina Ks 67402 5060 E mail address loservicedept landpride com Manual No 701 157M Exercise EXTREME CAUTION when plowing Always plow at a slow speed A WARNING TO AVOID SERIOUS INJURY OR DEATH l DO NOT EXCEED 5 MPH WITH BLADE INSTALLED 2 OPERATE WITH EXTREME CAUTION ON SLOPES STEEP GRADES AND ROUGH TERRAIN 3 KEEP AWAY FROM BLADE AND MOVING PARTS DURING OPERATION 4 WHEN PLOWING SNOW OR DIRT INTO A PILE START BACKING UP BEFORE RAISING THE BLADE 5 DO NOT RAM THE BLADE INTO THE PILE SLOW DOWN BEFORE HITTING PILE 6 BE AWARE OF POSSIBLE HIDDEN OBJECTS UNDER SNOW A CAUTION TO AVOID PERSONAL OR OTHER INJURY l READ BLADE OWNER S MANUAL ATV OPERATOR S MANUAL AND SAFETY DECALS BEFORE OPERAT ING 2 WEAR HEAD PROTECTION SAFETY GLASSES AND SHOES AS RECOMMENDED IN ATV OPERATOR S MANUAL 3 ALLOW NO RIDERS ON BLADE OR ATV WHILE MOVING OR STATIONARY 4 KEEP BYSTANDERS AWAY FROM BLADE OR ATV WHILE MOVING OR STATIONARY 5 BEFORE ADJUSTING BLADE ANGLE STOP ATV ENGINE SET AND LOCK BRAKES RAISE AND LOCK BLADE IN UP POSITION DO NOT ATTEMPT TO RAISE BLADE BY HAND USE THE LIFT HANDLE ONLY 6 BEFORE ADJUSTING B
10. t the Stops to the desired position they must be the same on both sides and tighten the bolts on the stops fully The Blade Skids on 60 blades are installed up side down at the factory for shipping boxing purposes Turn the Blade Skids around by loosening the two end bolts on the Blade and tighten the Bolts before using the Blade Blade Angle Operation To move the Blade Left Right or Straight pull the Blade Position Lever 5 forward and turn the blade to the desired position The Lever will automatically spring into the slot when the Blade reaches the proper angle Blade Lift Operation with a winch Method One The blade can be lifted using the winch Hook the winch hook onto the slot in the Blade Position Lever Bracke 3 and lift with the winch See diagram below Method Two Some assembly may be done for you Align the Cable Pulley 1 between the two Snatch 06 26 07 M Manual No 701 157M 3 Land Pride Assembly Instructions Block Straps 2 secure with the supplied 1 2 x 1 1 2 823 230C ST MOUNT KIT SNOW PLOW W INST bolt 3 and the 1 2 center lock nut 4 Do not over tighten The Cable Pulley 1 should be able to move freely See below Thread the winch cable under the Cable Pulley 1 as shown in the picture below Position the Snatch Block assembly over one of the holes on the blade position lever bracket Insure that the Snatch Block assembly is free of any moving parts and does not inter
Download Pdf Manuals
Related Search