Kodak DC210+ User's Manual
Contents
1. Picture size is 640 x 480 pixels Use this setting when the pic LS tures are for e mail or online use The Resolution setting is changed using the Preferences mode Refer to Resolution in Chapter 5 for more information Quality You may set your camera to capture pictures in a Good Better or Best quality setting The Quality setting indicates how much the picture is compressed to save space on the mem ory card Your pictures include more detail with the Best or Better setting but they will use more memory on the card than with the Good setting You may switch freely between the three settings when taking pictures The number of pictures the camera can store varies accordingly refer to the picture count table in the pre vious subsection 3 8 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide The Quality setting is indicated on the status display using the following icons QUALITY QUALITY QUALITY Good Use this setting to maximize the number of pictures stored Pic tures taken with this setting are suitable for computer and TV viewing Better Use this setting for general picture taking and to store a large number of pictures Best Use this setting when image quality is very important for maxi mum picture quality especially for larger sized or zoom prints The Quality setting is changed using the Preferences mode See Quality in Chapter 5 for more information Battery Status The2. in Chapter 5 for details The Exposure Lock icon appears if the exposure lock option is activated Refer to Tuming On Exposure Lock found later in this chapter for details The Exposure Compensation icon appears if the exposure value is adjusted Refer to Changing Exposure Compensation found later in this chapter for details To exit Preview press the Do It button again Preview automatically turns off when the camera is turned off Deleting the Picture Just Taken NOTE This delete feature is only available when the picture is shown on the LCD and the Quickview option is activated Refer to QuickView in Chapter 5 for more details 3 2 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide To delete the picture that was just taken without leaving Capture mode perform the fol lowing steps 1 Set the mode dial to Capture 2 Tum on the camera 3 Take a picture The picture is displayed on the LCD 4 Press the button The delete screen appears in the LCD NOTE The picture must be showing on the LCD screen to activate the delete screen 4 button ATT G 4 button Sii Do It button on gt butt w button 5 Press the or Y button until the correct delete option is highlighted 6 Press the Do It button The picture is deleted from the memory card To exit press the or W button until NO is highlighted and then press the Do It button Adjusting the Exposure Valu
3. 4 Monitor Adjustment oococcocoo e mr 7 5 Reinstalling the Camera Software 7 5 Getting Help soe sese mr EXE ERES ARA EA ERE puel Yd e 7 6 Index CHAPTER 1 Introduction Congratulations on your purchase of the new KODAK DIGITAL SCIENCE DC210 Plus Zoom camera that captures pictures digitally without the use of film The camera connects to the serial port of your computer to transfer pictures NOTE The camera includes an infrared transceiver to use with computers that include an infrared port Features The DC210 camera provides the following features 2X zoom lens 29 to 58 millimeters to zoom in on subjects and a close up option to set the focus at 8 inches 20 centimeters Built in flash with red eye reduction Status display of camera settings Removable memory card Video out capabilities that allow you to connect and run a slide show on your TV Color liquid crystal display LCD to immediately see or preview your pictures Software to easily transfer pictures from the camera to your computer A mode dial to activate one of four different functions on the camera Capture Takes previews or deletes last picture taken and adjusts the exposure Review Reviews or deletes pictures Preference Adjusts camera settings Connect Camera communicates with your computer Camera Kit Contents Your DC210 camera kit includes the following items DC210 camera Carrying case Introduction 1 1 e Me
4. Tum on the camera The LCD displays the Preferences screen Adjusting Camera Settings 5 9 3 Press the Y button until the Format Memory Card icon shown below is highlighted on the Preferences screen 4 Press the Do It button The LCD displays the main Format Memory Card screen A LITE amp E LLEITELLITILTIT mmi ou Y ES COD 5 To format the card press the Y button until CONTINUE FORMAT is highlighted Then press the Do It button To stop the formatting operation press a 4 or Y button until CANCEL FORMAT is highlighted and then press the Do It button Video Out The Video Out screen sets the camera s video output to National Television Standards Committee NTSC or Phase Alternating Line PAL format The video out format selected depends on your TV or video monitor In most cases European countries use a PAL format and other countries use an NTSC format To set the video out format perform the following steps 1 Set the mode dial to Preferences 2 Tumonthe camera The LCD displays the Preferences screen 3 Press the Y button until the Video Out icon shown below is highlighted on the Pref erences screen 5 10 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide 4 Press the Do t button The LCD displays the main Video Out screen The current setting is checked v A Y 5 Pressa A or Y button until the appropriate option i
5. Video Out in Chapter 5 for details 7 Pressa 4 or button on the camera to scroll through the pictures on the TV To run a slide show press the Do It button The slide show starts and the pictures change every five seconds for a period of five minutes If you are using an AC adapter the slide show runs indefinitely To cancel the slide show press the Do It button The slide show stops and the main Review screen reappears 4 4 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide CHAPTER 5 Adjusting Camera Settings When the mode dial is set to Preferences the main Preferences screen appears on the liq uid crystal display LCD The Preferences screen illustrated below allows you to adjust or activate the following camera settings Quality icon Best High Off Off 7 Resolution icon Template icon gt ki ij Date Stamp icon e File Type icon JPEG A Quickview icon On default Date Time icon gt 07 22 settings LCD Brightness icon gt 0 kd Format Memory Card icon Farm at A Video Out icon i NTSC Language icon English About icon About l al The following sections describe each of these settings Adjusting Camera Settings 5 1 Quality The Quality screen sets the picture quality to Best Better or Good Refer to Quality in Chapter 3 for more information on picture quality To set quality perform t
6. Your monitor display settings may need to be adjusted to view pictures from the camera To do so perform the following steps 1 Double click the My Computer icon 2 Double click the Control Panel icon 3 Double click the Display icon and click the Settings tab 4 Selectthe highest available setting for Color Palette and click the OK button Reinstalling the Camera Software To reinstall the camera software perform the following steps 1 Close all open application programs 2 Place the camera software CD into your CD ROM drive 3 Inthe Welcome window click the Next button 4 Read the license agreement and click the Yes button to accept the software license agreement If you do not accept the license you cannot install the software 5 Selectthe software item you want to install and click the Next button 6 Select the name of the program folder and click the Next button If necessary type a new folder name or select from the Existing Folders list Troubleshooting 7 Verify the settings and then click the Next button A progress screen appears while the software is installed 8 Selectthe preferred restart option and click the Finish button NOTE If you installed the mounter software you must restart your computer Getting Help Additional tips and troubleshooting instructions are available on the Kodak Web site at www kodak com If problems persist contact Dell Computer Corporation for technical assistance refer t
7. and Deleting Pictures in Chapter 4 NOTE The Pictures Remaining number does not always change by one when a picture is taken if the picture content is easily compressed Self Timer Activating the Self Timer option creates a 10 second delay between the time you press the shutter button and when the picture is taken so you can include yourself in the picture To activate this function perform the following steps 1 Set the mode dial to Capture 2 Tumon the camera 3 Press the self timer button The Self Timer icon appears on the status display 4 Place the camera on a flat steady surface or tripod Taking Pictures 5 Pressthe shutter button The red self timer light located on the front of the camera tums on and stays lit for 8 seconds The self timer light flashes for 2 additional seconds just before the picture is taken Self Timer returns to the off setting once the picture is taken To stop this function press the self timer button again before the picture is taken Memory Card Status The Card Status icon changes automatically to indicate if there is a memory card inserted in the camera You may not select or change this icon No card inserted Pictures cannot be taken LI Card inserted Pictures are saved to the card s memorv Close Up The camera includes a close up button that allows vou to set the camera s focus distance at 8 inches 20 centimeters cm The red eye reduction option for
8. exhibit the memory effects seen with other rechargeable technologies If you use alkaline batteries in your camera obtain photo flash grade alkaline batteries These types of batteries last more than twice as long in digital cameras as ordinary alkaline batteries Ni Cd batteries work well in digital cameras but they typically provide the shortest duty cycle usable power between charges Lithium batteries typically provide the longest overall battery life but they carry a higher cost perpicture than other nonrechargeable battery types While using your batteries observe the following guidelines Always follow your battery manufacturer s directions fully Replace the batteries when they are low Otherwise the camera may shut down with its lens extended Limit continuous LCD preview or review operations to less than 20 minutes per ses sion If you anticipate using your camera for longer periods in these modes Kodak recommends that you use the AC adapter with the camera Dispose of batteries according to federal and local regulations Removing and Inserting Memory Cards The DC210 camera comes with a KODAK DIGITAL SCIENCE picture card memory card The reusable memory card stores the pictures taken with the camera The memory card is required for camera operation NOTE Use only certified memory cards in your camera that carry the CompactFlash logo CAUTION Do not eject or insert a card when the ready light is b
9. mode dial to Preferences 2 Tum on the camera The LCD displays the Preferences screen 3 Press the Y button until the About icon shown below is highlighted on the Prefer ences screen i 5 12 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide 4 Press the Do It button The LCD displays the About screen Shee bh mm ESI zn il EE reme eae DR fail jil whine Fo ai 5 Press the Do It button to return to the main Preferences screen Adjusting Camera Settings 5 13 5 14 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide CHAPTER 6 Transferring Pictures From the Camera to the Computer This chapter explains how to connect the camera to your Dell computer and start the Picture Easy software Serial Cable Connection To connect the camera to your Dell computer with the serial cable provided with your cam era perform the following steps 1 Set the mode dial to Connect NOTE While in Connect mode the camera is controlled by the computer Except for the mode dial and power button all other camera buttons are ignored The Ready light indicates when the camera is on mode dial Transferring Pictures From the Camera to the Computer 6 1 2 Plug one end of the serial cable into the 9 pin serial COM port on the back of your computer serial port connector 3 Openthe serial port door on the side of your camera serial port 4 Plugthe other end of the se
10. set for red eye reduction Templates do not work The memory card may not contain the templates Only the original memory card contains templates Templates are lost when the memory card is formatted Instructions for replacing the templates can be found on the Kodak Web site at www kodak com Troubleshooting 7 3 Problem Cause Solution Date and time lost Date and time infor mation is lost if the batteries totally discharge Change the batteries before they totally discharge Do not open the battery door while the camera is on LCD Messages Message Cause Solution Memory Card is Full No Memory Card Cannot read memory card Cannot establish connection Camera needs service Memory card is full and cannot hold additional pictures There is no memory card inserted in the camera Memory card is corrupted The camera cannot communicate with the computer The camera is malfunctioning Transfer pictures to your computer or insert a memory card that has available memory Insert a memory card in the camera Insert a new memory card or format the memory card Make sure the camera is connected to the computers serial port Contact Dell for camera service or repair Refer to Getting Help found later in this chapter Printing Tips You may notice that the colors on your computer screen do not always match those in your documents
11. the camera for more than a few minutes or when the camera is on the Date Time setting is deleted and must be reset LCD Brightness The LCD Brightness screen adjusts the brightness of the camera s LCD screen To make an adjustment perform the following steps 1 Set the mode dial to Preferences 2 Tum on the camera The LCD displays the Preferences screen 5 8 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide Press the Y button until the LCD Brightness icon shown below is highlighted on the Preferences screen Press the Do It button AOF The LCD displays the main LCD Brightness screen EN MS Y ES COD Press a 4 or Y button to adjust the brightness of the LCD screen to the appropri ate level The brightness of the LCD screen changes as the setting is adjusted Press the Do It button The main Preferences screen reappears The LCD Brightness setting is maintained until another setting is selected This setting does not change when the camera is tumed off Format Memory Card The Format M emory Card screen formats the memory card while it is in the camera and sets up new directories and pointers on the card CAUTION When a memory card is formatted it erases everything on the card including any pictures and templates The templates cannot be restored without a memory card reader To format a memory card perform the following steps 1 Set the mode dial to Preferences
12. the flash setting is not available when Close Up is on NOTE To accurately capture the picture in Close Up the Preview option automatically starts when the close up button is pressed Refer to Previewing a Picture found earlier in this chapter for detailed information To deactivate the Preview option press the Do It button To tum on the Close Up setting perform the following steps 1 Set the mode dial to Capture 2 Tumon the camera 3 Press the close up button The Close Up icon appears on the status display 4 View the subject on the LCD display to accurately capture the picture To cancel Close Up press the close up button again The Close Up icon disappears from the status display The Close Up setting is automatically tumed off when the camera is tumed off 3 6 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide Flash The camera is equipped with a built in flash that offers an optional red eye reduction fea ture The flash has an effective range of approximately 16 to 9 8 feet 0 5 to 3 meters There are five Flash settings A Auto Flash fires automatically when the shutter button is pressed 5 and the camera determines that there is not enough light This is the default setting A Auto Red eye Works the same as Auto except the flash fires once 5 e before the picture is taken to reduce the chance of red eve and then flashes a second time when the picture is taken Fill Flash fires every time y
13. your camera Additional memory cards e Memory card reader e Snapshot and photographic quality paper To order any of these accessories contact DellWare at 1 800 753 7201 in the U S or a Kodak dealer in the U K 1 2 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide An Orientation to Your Camera The following illustrations identify the features of the DC210 camera Front of Camera self timer light sensor viewfinder flash flash sensor infrared tensceher A f lens light sensor Top of Camera shutter status display A C ff SC power button my g CU 79 ia flash button 018 a close up l button self timer button Introduction 1 3 Back of Camera viewfinder oom Ready light a mode dial LCD screen in 4 button IL gt button Me Bottom of Camera batterv door memorv card eject i o a switch rp val GU c T j J tripod socket Side of Camera memory card door Z L serial connector video out connector AC adopter o E connector n W 1 4 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide CHAPTER 2 Operating the Camera This chapter describes basic camera operations such as using batteries and the AC adapter inserting and removing t
14. 5 6 R reinstalling software 7 5 removing a memory card 2 2 resolution 3 7 5 3 Review mode 4 1 S safety instructions v screen brightness 5 8 Self Timer icon 3 5 serial cable connection 6 1 setting the date 5 7 setting the language 5 11 setting the resolution 3 7 setting the Self Timer option 3 5 setting the time 5 7 slide show 4 4 software about 1 2 mounter 1 2 Picture Easy 1 2 6 3 reinstalling 7 5 TWAIN 1 2 status display icons 3 5 T taking pictures 3 1 adjusting the exposure value 3 3 technical assistance 7 6 Template icon 3 2 templates using 5 3 time setting 5 7 troubleshooting camera checks 7 2 getting help 7 6 LCD messages 7 4 memory card checks 7 1 monitor adjustments 7 5 monitor checks 7 1 printing tips 7 4 reinstalling camera software 7 5 TWAIN software 1 2 v video output format 5 10 viewing a slide show on TV 4 4 viewing available memory 4 1 Index 3 viewing camera information 5 12 Z viewing pictures on memory card 4 1 GEN zooming 3 10 viewing pictures on TV 4 3 4 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide Printed in the U S A 3866D x P N 3066D
15. KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera A al www kodak com KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera www kodak com Information in this document is subject to change without notice 1998 Dell Computer Corporation All rights reserved 1998 Eastman Kodak Company All rights reserved Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden Trademarks used in this text Dell is a registered trademark and DellWare is a registered service mark of Dell Computer Corporation Kodak is a registered trademark and KODAK DIGITAL SCIENCE FlashPix and Photolife are trademarks of Eastman Kodak Company Microsoft Windows and Windows NT are registered trademarks of Microsoft Corporation Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its own The FlashPix format is defined in a specification and test suite developed and published by Kodak in collaboration with M icrosoft Hewlett Packard and Live Picture Only products that meet the specification and pass the test suite may use the FlashPix name andlogo October 1998 P N 3066D Safety Instructions When using your digital camera always follow these basic safety precautions WARNING Use of co
16. camera comes with four Kodak Photolife AA batteries Standard 15 V alkaline 15 V lithium or rechargeable 12 V nickel cadmium Ni Cd or nickel metal hydride Ni M H batter ies may be used The battery power icon changes automatically You may not select or change this icon NOTE To retain the Date Time setting replace the batteries as soon as the battery power icon begins to blink j Full Batteries are fully charged Low Batteries need to be replaced Blinking Batteries are insufficient to run camera and need to be replaced NOTE Pictures on memory cards are not lost if the batteries are depleted Taking Pictures 3 9 Activating the Zoom The camera includes a 2X zoom lens that allows you to zoom in on your subject from wide angle 29 millimeters mm to telephoto 58 mm wide angle telephoto To activate the zoom perform the following steps 1 Set the mode dial to Capture 2 Tumon the camera 3 Press the zoom button The subject appears closer or farther away when you look through the viewfinder and press the zoom button zoom button Cli O amp mode dial The camera s default lens position is wide angle All other lens positions are considered telephoto settings 3 10 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide CHAPTER 4 Reviewing Pictures When the mode dial is set to Review you may use the liquid crystal display LCD to view the pict
17. d te cule s dat A dew Den Ma ADA a 3 10 Chapter 4 Reviewing PictureS oooooooooo oo eere bl Viewing Pictures on the Camera 4 1 Deleting Pictures de eee aee edt AER tels tix uis 4 2 Magnifying Pictures 2 mme 4 3 Viewing Pictures or Running a Slide Show on a TV 4 3 Chapter 5 Adjusting Camera Settings cere orl UIE xa At heh PED 5 2 RES OMIM eo eid vec cs A 5 3 Template naen Vcn age tees ue se ta ar oe P o Et dde Yee eed uidere 5 3 Date Stamp is deett dete te ae nonae a Renten et per eat 5 4 File Type i mE 5 5 QUIEKVIEW a vt dada deducted A C E UR ke 5 6 Date and Time i ree ep erate cased Wagaya egeo ei aes 5 7 ECD Brightness sco sse ate ta eg eas dae EPA Peale waded art 5 8 Format Memory Card xs cee keaton ee eh one Geek d eet ap Rae Wan toa 5 9 Video OUE correr eue pue Geol ee pera ee a ee Re ERE px du 5 10 Language E wer E AAA E AER 5 11 ADOUL ai wet tainted pecie IRA paa ira Ox ca dore ea 5 12 Chapter 6 Transferring Pictures From the Camera to the Computer oooooooo ooo oo oo ooo e 6 1 Serial Cable Connection ooooocoooocncon ashes 6 1 Infrared Connection 6 3 Chapter 7 Troubleshooting eee eee oes 7 1 Monitor Checks aii ot atttem une Feet CU tures dae gd d ta 7 1 Memory Card Checks aasan annaa 7 1 Camera Checks ome rt Aastha hath Att Pea oe i Rn ns 7 2 LED Messages M LU 7 4 Printing IDS A A A DI ete m ex du eno D et Mt mtd ud rk 7
18. e The camera s exposure value EV can be adjusted from 2 0 to 2 0 EV in 0 5 increments while in Capture mode A L0 adjustment in EV doubles the amount of light allowed to reach the charge coupled device CCD in your camera A 10 adjustment in EV halves the amount of light allowed to reach the CCD in your camera If your pictures are too dark increase the exposure compensation setting If they are too light decrease the exposure compensation setting Changing Exposure Compensation To change exposure compensation perform the following steps 1 Set the mode dial to Capture 2 Tum the camera on Taking Pictures 3 3 3 Pressthe gt button The LCD displays the Exposure Compensation screen 4 Press the and buttons to adjust the exposure 5 Press Do t to select the exposure setting The exposure setting automatically resets to 0 0 EV when the camera is turned off Turning On Exposure Lock Use Exposure Lock to take a sequence of pictures that require the same exposure When this setting is activated the camera maintains a constant exposure setting To tum on Exposure Lock perform the following steps 1 Set the mode dial to Capture 2 Tum the camera on 3 Pressthe gt button two times The Exposure Compensation screen appears followed by the Exposure Lock screen NOTE Press the b button a third time to exit the Exposure menu 4 Pressthe or Y button until ON is highlighted 5 Press the Do It bu
19. e type perform the following steps 1 Set the mode dial to Preferences 2 Tumonthe camera The LCD displays the Preferences screen 3 Press the Y button until the File Type icon shown below is highlighted on the Pref erences screen 4 Press the Do It button The LCD displays the main File Type screen The current setting is checked 7 A Y amp D COD 5 Pressa or Y button until the appropriate option is highlighted 6 Press the Do It button The main Preferences screen reappears The File Type setting is maintained until another setting is selected This setting does not change when the camera is turned off Quickview The Quickview screen tums the camera s Quickview setting on or off When you take a pic ture with Quickview on the picture momentarily appears on the LCD screen seconds after the picture is taken NOTE The Quickview option must be activated to use the delete feature available in Cap ture mode Refer to Deleting the Picture J ust Taken in Chapter 3 for more details 5 6 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide To tum on Quickview perform the following steps 1 2 Set the mode dial to Preferences Tum on the camera The LCD displays the Preferences screen Press the Y button until the Quickview icon shown below is highlighted on the sec ond Preferences screen 4 Q v Press the Do It button The LCD displays the main Quickvie
20. entation to Your Camera 1 3 Eront of Camera oue cert isch weaken Dance WEE deals Deis d 1 3 TOP of Camera eee aa 1 3 Bacl of Camera it eu S rera oer t RR RICE ae i ae eo Mops 1 4 Bottom of Camera ecd ea Ad dns 14 Side of Camera uere a ae tc e de ged eae es 1 4 Chapter 2 Operating the Camera eere eee 2 1 Installing Batteries ooooooooocooco II HH 2 1 Battery Usage Guidelines 2 2 Removing and Inserting Memory Cards 0 00 cette eee 2 2 Turning the Camera On and Off 1 0 ect tte es 2 3 Using the AC Adapter 1 2 0 0 0c cette ees 2 3 Caring for the Camera 24 Chapter 3 Taking Pictures Re ek dl TAKING A PICtUe ces mr COCOS Ee OE eee ee hele apros 3 1 Previewing a Picture LL L 3 2 Deleting the Picture J ust Taken 0000 3 2 Adjusting the Exposure Value 3 3 Changing Exposure Compensation 0000 e 3 3 Turning On Exposure Lock 3 4 vii viii Adjusting Camera Settings Using the Status Display 0 3 4 Pictures Remaining 3 seb Gaede er ree e op A 3 5 Self TII Tier so ES TUDIN REIR SRE ELE 3 5 Memory Card Status L00 00 rr 3 6 Close Up sse eer erate a ete A Peale elt oa Pas nella ER 3 6 Flash esto i i ed este Roque tentes am a f 3 7 Resolution teens Ru a pet e p RAT sceptra ee ER en ue eee Fo ER 3 7 Quality e ne xor OW RUD ORAE A RG ee ORT 3 8 Battery Status i 1 a OR ace aer ntu Fee RU Gea eet rci E eerte 3 9 Activating the ZOOM esce spu
21. he camera back on Transferring Pictures From the Camera to the Computer 63 6 4 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide CHAPTER 7 Troubleshooting This chapter provides tips and troubleshooting solutions for common problems you may experience while using your camera and software If you are experiencing difficulties with your camera check the sections for possible solutions Monitor Checks Problem Cause Monitor is not set correctly The image on your monitor is jagged or inappropriately colored Memory Card Checks Solution Adjust your monitor display settings as described in Monitor Adjustments found later in this chapter Problem Cause Solution The camera does not recognize your mem ory card The memory card may not be ATA compatible The memory card may contain com pression or stacker software Memory cards must be ATA compatible to work with the camera Reformat any memory cards that con tain compression or stacker software Refer to the memory card documenta tion or Format M emory Card in Chapter 5 for instructions on reformat ting the card Troubleshooting 7 1 Camera Checks Problem Cause Solution Ready light does not tum on and the cam era does not work Camera is not turned on Batteries are low or empty Turn on the camera and verify that the green Ready light turns on Replace the batteries Pictures remain in
22. he following steps 1 Set the mode dial to Preferences mode dial 2 Tumonthe camera The LCD displays the Preferences screen 3 Press the Y button until the Quality icon shown below is highlighted aan U ELU 4 Press the Do It button The LCD displays the main Quality screen The current setting is checked A Y 5 Pressa or Y button until the appropriate option is highlighted 6 Press the Do It button The main Preferences screen reappears The Quality setting is maintained until another setting is selected This setting does not change when the camera is turned off KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide Resolution The Resolution screen sets the picture resolution to High 1152 x 864 pixels or Standard 640 x 480 pixels Refer to Resolution in Chapter 3 for more information on picture resolution To set resolution perform the following steps 1 Set the mode dial to Preferences 2 Tumonthe camera The LCD displays the Preferences screen 3 Press the Y button until the Resolution icon shown below is highlighted gH 4 Press the Do It button The LCD displays the main Resolution screen The current setting is checked A Y 5 Pressa or Y button until the appropriate option is highlighted 6 Press the Do It button The main Preferences screen reappears The Resolution setting is maintained until anot
23. he memory card and tuming the camera on and off This chapter also provides maintenance procedures for the camera Installing Batteries The DC210 camera comes with four Kodak Photolife AA batteries Standard 15 volt V alkaline L5 V lithium or rechargeable 12 V nickel cadmium Ni Cd or nickel metal hydride Ni MH batteries may be used To install the batteries perform the following steps 1 Place your thumb on the battery door 2 Slide the battery door away from the camera 3 Insertthe batteries as indicated on the battery door and close the door Remove the batteries if the camera will not be used for an extended period of time Doing so extends battery life and prevents camera damage from battery leaks or corrosion If the batteries are removed from the camera for more than a few minutes the camera s date and time features are deleted and must be reset For information on setting the date and time refer to Date and Time in Chapter 5 WARNING Take care when removing the batteries as they may be hot Allow them to cool before touching them Operating the Camera 2 1 Battery Usage Guidelines Battery life depends significantly on age usage conditions type and brand In general dig ital cameras are very demanding on batteries In Kodak lab tests Ni MH rechargeable batteries delivered the best results in a variety of conditions Ni MH batteries are designed for high demand devices like digital cameras and they do not
24. he mode dial is set to Capture the camera can perform the following functions Capture a picture Preview pictures on the liquid crystal display LCD Delete a picture just taken Adjust the exposure Adjust some camera settings using the status display Each of these functions is explained in this chapter Taking a Picture To take a picture perform the following steps 1 Set the mode dial to Capture Mode dial Tum on the camera Center subject in the viewfinder Press the shutter button The green Ready light Memory Card icon and Pictures Remaining number on the sta tus display blink rapidly as the camera processes the picture NOTE You do not need to hold the camera still while the green Ready light is blinking but you will not be able to take another picture until it stops Taking Pictures 3 1 Previewing a Picture You can use the LCD as a live viewfinder while in Capture mode This function allows you to preview your picture before it is taken NOTE Preview significantly shortens battery life To activate Preview perform the following steps 1 Set the mode dial to Capture 2 Tumon the camera 3 Press the Do It button The LCD displays the subject that is viewed from the viewfinder with the icons of acti vated camera features Template Exposure Lock icon icon Exposure Compensation icon The Template icon appears if the template option is activated Refer to Template
25. her setting is selected This setting does not change when the camera is turned off Template The Template screen selects a creative border and or logo that is added to your picture when you take it The memory card supplied with your camera includes seven templates NOTE If you take a picture with the template feature activated the template cannot be removed from that picture Adjusting Camera Settings 5 3 To select a template perform the following steps 1 Setthe mode dial to Preferences 2 Tumonthe camera The LCD displays the Preferences screen 3 Press the Y button until the Template icon shown below is highlighted 4 Press the Do It button The LCD displays the main Template screen The current setting is checked A 9 Y QC ED 5 Pressa or Y button until the appropriate option is highlighted 6 Press the Do It button The main Preferences screen reappears NOTE The template is visible after the picture has been taken with the camera in either Review mode or in Capture mode with Quickview activated To tum off the template feature press a 4 or Y button until OFF is highlighted and then press the Do It button The Template setting is maintained until another setting is selected This setting does not change when the camera is turned off Date Stamp The Date Stamp screen records the date on your pictures To tum on Date Stamp perform the following steps 1 Se
26. linking Doing so may damage your pictures or camera To remove the memory card perform the following steps 1 Open the memory card door on the side of the camera 2 Pressthe eject button on the bottom of the camera The card partially slides out of the slot 3 Take hold of the card carefully remove it from the slot and close the card door 2 2 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide To insert the memory card perform the following steps 1 Open the memory card door on the side of the camera 2 Holdthe memory card with the connecting end pointed at the camera 3 Push the card all the way into the card slot and close the card door To obtain additional memory cards for your camera contact DellWare at 1 800 753 7201 in the U S or a Kodak dealer in the U K Turning the Camera On and Off To tum the camera on or off press the power button on the top of the camera The green ready light on the back of the camera and the status display screen tum on or off NOTE If the camera is turned off while a picture is being processed the camera finishes processing the picture before turning off If your camera is idle for approximately 5 minutes it automatically turns off To turn the camera on again press the camera s power button Using the AC Adapter An AC adapter allows you to connect your camera to a standard electrical outlet AC power is especially useful when you are transferring pictures into you
27. mory card installed in camera AC adapter Four Kodak Photolife AA batteries e Quick Reference card and this guide Serial cable Video output cable For information on using the memory card and power sources with the camera refer to Chapter 2 Operating the Camera Digital Camera Software Dell installed the following software on the hard disk drive of your computer before ship ping your computer system and camera Picture Easy Picture processing software that allows you to transfer organize edit share and print pictures taken with your camera For more information on this soft ware refer to the Using the Picture Easy Software section of the online KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide The guide can be accessed by clicking the Start button on the Microsoft Windows desktop pointing to Programs gt Dell Documents and clicking Kodak DC210 Camera User s Guide e Mounter software Allows you to view transfer or delete pictures stored on the camera s memory card through your operating system e TWAIN software An industry standard interface that allows you to directly transfer pictures stored on the camera s memory card into a TWAIN compliant application pro gram such as Adobe PhotoDeluxe Store the backup software CD that came with your system in a safe place in case you ever need to reinstall the software Camera Accessories The following accessories are available for
28. ntrols adjustments or procedures other than those speci fied in the Kodak documentation may result in exposure to shock electrical hazards and or mechanical hazards e Read and understand all instructions before using the camera e To reduce the risk of electric shock do not immerse the digital camera in water or any other liquid e Never disassemble or touch the inside of the camera This action could result in elec trical shock Service or repair work should be done by a qualified service person Incorrect reas sembly can cause electric shock To keep from damaging your camera avoid exposing it to moisture and extreme temperatures e Only use approved batteries in your digital camera e f you notice smoke or a strange smell coming from the camera immediately turn off the camera wait a few moments until the camera cools and then remove the batteries e Donotattempt to disassemble recharge short circuit or subject the batteries to high temperatures or fire e Only use the AC adapter supplied with the digital camera Use of an accessory attach ment not provided or recommended by Kodak may cause fire electric shock or injury vi Contents Chapter 1 Introduction 2 22 oue ads dl A c c ior sre et ease ette t Ao p redi e Re a l G 1 1 Camera Kit Contents persse costra Sites dag eee eel METUS EZ 1 1 Digital Camera Software 6 erre 1 2 Camera ACcessones i sia fice Pea ede pee A Oa ed Pe ee ERR E 1 2 An Ori
29. o the Getting Help chapter of your system Reference and Trouble shooting Guide 76 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide Index A AC adapter connecting 2 3 accessories 1 2 adjusting the exposure value 3 3 batteries installing 2 1 removing 2 1 status 3 9 types 2 1 2 2 3 9 usage guidelines 2 2 C camera accessories 1 2 features 1 1 1 3 package contents 1 1 software 1 2 troubleshooting 7 2 viewing information about 5 12 camera modes about 1 1 Capture 3 1 Preferences 5 1 Review 4 1 camera settings About 5 12 adjusting 3 5 Date and Time 5 7 Date Stamp 5 4 camera settings continued File Type 5 5 Format M emory Card 5 9 Language 5 11 LCD Screen Brightness 5 8 Quality 5 2 QuickView 5 6 Resolution 5 3 Template 5 3 Video Out 5 10 camera settings changing activating Self Timer 3 5 selecting Flash settings 3 7 selecting quality setting 3 8 selecting the resolution 3 7 zooming 3 10 Capture mode 3 1 Close Up icon 3 6 connecting AC adapter 2 3 6 2 connecting the camera to a computer infrared connection 6 3 using serial cable 6 1 connecting the camera to a TV 4 3 D dark pictures 3 3 date stamp 5 4 date setting 5 7 deleting last picture taken 3 2 deleting one or all pictures 4 2 Index 1 E error messages 7 4 exposure compensating for dark or light pictures 3 3 Exposure Compensation icon 3 2 Exposu
30. on the flash Refer to Flash in Chapter 3 Move so there is no more than 10 ft 3 m between the camera and the subject Change your position so the light is not behind the subject Picture is too light The flash is not needed The subject was too close when you used the flash The light sensor is covered Change to automatic flash Refer to Flash in Chapter 3 Move so there is at least 16 ft 0 5 m between the camera and the subject Hold the camera so your hands or other objects do not cover the light sensor Stored pictures are damaged The memory card was removed when the Ready light was blinking Make sure the Ready light is not blink ing before removing the memory card Pictures remaining number does not decrease The image resolu tion does not take up sufficient space to decrease the pic ture remaining The camera is operating normally Con tinue taking pictures number Picture is not clear The lens is dirty Clean the lens Refer to Caring for the Camera in Chapter 2 The subject was too Move so that there is at least 16 ft close when you took the picture Subject or camera moved during pic ture taking 0 5 m between the camera and the subject Stand at least 8 in 20 cm away for close ups and at least 3 28 ft 1 m for telephoto pictures Hold camera steady during picture tak ing until after the flash or the second flash if the camera flash is
31. onthe camera The last picture taken appears on the LCD screen The Overlay screen is turned on 3 Pressa or Y button until the Delete icon is highlighted 4 Press the Do It button The delete screen appears on the LCD 5 Pressa 4 or P button until the appropriate picture is highlighted on the filmstrip NOTE To delete all the pictures on the memory card press a 4 or Y button until ALL PICTURES is highlighted and then press the Do It button 6 Press the Do It button That picture is deleted from the memory card To exit the Overlay screen press the or Y button to highlight the Overlay icon Then press the Do It button to tum off the Overlay screen The main Review screen reappears NOTE Memory cards containing images captured from other digital cameras have less memory space available when used in the DC210 camera To free up memory space on 4 2 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide the memory card you must delete the images in the camera model that captured those images Magnifying Pictures The Magnify feature allows you to view the current picture at 2x size on the LCD screen when in Review mode To magnify a picture in Review mode perform the following steps 1 Set the mode dial to Review 2 Tumonthe camera The last picture taken appears on the LCD screen The Overlay screen is turned on 3 Pressa 4 or gt button until the appropriate picture is highlighted on the filmstrip 4 Pres
32. or prints This happens because monitors and printers use different color Systems You may be able to achieve more predictable results in your printed documents by taking the following actions e Improve the quality of your paper Copier paper may not offer the same results as coated paper or paper made especially for inkjet printers Adjust your printer software settings e Use fresh ink cartridges Do not use ink cartridges beyond their life expectancy 74 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide Keep these tips in mind when printing Color printing takes more time Complex documents require more printing and drying time Color printing is more memory intensive than black and white If your computer gives you an insufficient memory message you may need to close some application pro grams change some settings or add additional memory Color prints may not photocopy as clearly as black and white If you plan to photocopy documents consider printing the document in gray scale This setting is usually changed from the Print menu Resizing the picture to a smaller size or printing the picture on glossy paper may increase the quality of the print To improve the quality of your prints you may want to print your pictures on KODAK DIGI TAL SCIENCE snapshot paper This paper works with most inkjet printers and gives you Clearer crisper and more detailed images on your prints Monitor Adjustment
33. ou press the shutter button Use this set ting when the lighting is poor or when your subject is lit from behind Fill Red eye Works the same as Fill flash setting except the flash O fires once before the picture is taken to reduce the chance of red eye and then flashes a second time when the picture is taken 5 Off Flash is tumed off and does not fire To change the Flash setting perform the following steps 1 Set the mode dial to Capture 2 Tum on the camera 3 Press the flash button to scroll through and select the appropriate Flash settings Flash retums to its default setting when the camera is tumed off Resolution Resolution indicates the size of the picture in pixels The camera can be set to capture pictures in a high or standard resolution Your pictures include more detail with high resolu tion but they will use more memory on the card than at the standard resolution setting Taking Pictures 3 7 You can switch freely between the two settings when taking pictures The number of pic tures the camera is able to store varies accordingly Resolution Quality Number of Pictures High Best 20 Better 28 Good 45 Standard Best 41 Better 57 Good 87 The Resolution setting is indicated on the status display using the following icons IIT High Picture size is 1152 x 864 pixels This is the default setting Use sess this setting when your pictures are to be printed JUS Standard
34. r computer The adapter powers the camera but does not charge the batteries WARNING Only use the AC adapter designed for the DC210 camera Use of any other adapter may void the warranty and can cause camera failure fire electric shock or injury Operating the Camera 2 3 To connect the AC adapter to the camera perform the follow ing steps 1 Insert the AC adapter into the AC adapter connection on the side of your camera AC adapter connection 2 Connectthe other end of the adapter to a wall outlet 3 Tumonthe camera NOTE The battery icon does not appear on the status display when an AC adapter is used Caring for the Camera Clean the outside of the camera by wiping it with a clean dry cloth Never use harsh or abrasive cleaners or organic solvents on the camera or any of its parts To clean the camera lens and liquid crystal display LCD screen perform the following steps WARNING Do not use cleaning solutions unless they are designed specifically for camera lenses Do not wipe the camera lens or LCD screen with chemically treated eyeglass lens tissue as it may scratch the lens 1 Blow gently on the lens or LCD screen to remove dust and dirt 2 Moisten the lens or LCD screen by breathing lightly on it 3 Wipe the lens or LCD screen gently with a soft lint free cloth or an untreated lens cleaning tissue 2 4 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide CHAPTER 3 Taking Pictures When t
35. re Lock icon 3 2 F file types 5 5 Flash settings 3 7 FlashPix file format 5 5 formatting memory cards 5 9 G getting help 7 6 l infrared connection 6 3 inserting a memory card 2 2 installing batteries 2 1 J J PEG file format 5 5 L language setting 5 11 LCD messages 7 4 LCD screen brightness 5 8 light pictures 3 3 M magnifying a picture in Review mode 4 3 memory card deleting pictures from 4 2 formatting 5 9 inserting and removing 2 2 M emory Card icon 3 6 troubleshooting 7 1 viewing available memory 4 1 viewing pictures on 4 1 M emory Card icon 3 6 messages 7 4 monitor adjustments 7 5 checks 7 1 mounter software 1 2 N NTSC format 5 10 O Ovenlay screen 4 1 P PAL format 5 10 Picture Easy software 1 2 6 3 picture quality 3 8 5 2 Pictures Remaining icon 3 5 Preferences mode 5 1 Preferences screens About 5 12 about 5 1 Date Stamp 5 4 Date Time 5 7 File Type 5 5 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide Preferences screens continued Format M emory Card 5 9 Language 5 11 LCD Screen Brightness 5 8 Quality 5 2 Quickview 5 6 Resolution 5 3 Template 5 3 Video Out 5 10 Preview exiting 3 2 Exposure Compensation icon 3 2 Exposure Lock icon 3 2 Template icon 3 2 previewing a picture 3 2 previewing a picture just after taking it 5 6 printing tips 7 4 Q Quality icon 3 8 Quickview option
36. rial cable into the camera s serial port 5 Insert the AC adapter into the AC adapter connection on the side of your camera AC adapter connection 6 Connectthe other end of the AC adapter to a wall outlet 6 2 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide 7 Tumonthe camera When the camera is correctly connected to your computer three squares rotate on the status display 8 Tum on your computer system 9 Startthe Picture Easy software by double clicking the Picture Easy icon on your Win dows desktop s You can also start the software by clicking the Start button pointing to Programs gt Kodak gt Picture Easy Software and clicking Picture Easy For more information on this software refer to the Using the Picture Easy Software section of the online KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide The guide can be accessed by clicking the Start button pointing to Programs gt Dell Documents and clicking Kodak DC210 Camera User s Guide To cancel the connection turn the mode dial to another setting or turn off the camera Infrared Connection Your computer must be set up with an infrared connection before the camera s infrared transceiver can be used NOTE If you are using the camera s infrared transceiver to connect to the computer and the camera automatically tums off because of inactivity you need to press the cameras power button to tum t
37. s highlighted 6 Pressthe Do It button The main Preferences screen reappears The Video Out setting is maintained until another setting is selected This setting does not change when the camera is turned off Language The Language screen selects a language interface for the camera When you choose a spe cific language the LCD screens on the back of the camera change to reflect the selected language To select a language perform the following steps 1 Set the mode dial to Preferences 2 Tumonthe camera The LCD displays the Preferences screen 3 Press the Y button until the Language icon shown below is highlighted on the Pref erences screen Adjusting Camera Settings 5 11 4 Press the Do It button The LCD displays the main Language screen The current setting is checked A Y 5 Pressa or Y button until the appropriate language is highlighted 6 Press the Do It button The main Preferences screen reappears The language setting is maintained until another setting is selected This setting does not change when the camera is turned off About The About screen is a view only screen that keeps a record of the camera s use It provides the following information e Firmware version e Total number of pictures taken over the lifetime of the camera Total number of flashes fired over the lifetime of the camera To view the About screen perform the following steps 1 Set the
38. sa A or Y button until the Magnify icon is highlighted 5 Press the Do It button The LCD displays a magnified view of the selected picture 6 Use the 4 p Ax or Y buttons to scroll to different parts of the picture To cancel the M agnify feature press the Do It button The Overlay screen reappears To exit the Overlay screen press the or Y button to highlight the Overlay icon Then press the Do It button to tum off the Overlay screen The main Review screen reappears Viewing Pictures or Running a Slide Show on a TV The Video out feature allows you to connect the camera to a TV and then view or run a slide show of the pictures from the memory card on your TV This feature is especially use ful when sharing pictures with family and friends NOTE The camera s LCD screen is disabled when the video output cable is attached to the camera Reviewing Pictures 4 3 To view pictures on a TV perform the following steps 1 Tum off your TV and the camera 2 Insertthe video output cable into the video out connection on the side of your camera video out ZA connection xcd ES 3 Connect the other end of the cable to the video in connection on your TV 4 Tum on the camera and TV 5 Setthe mode dial on the camera to Review 6 Setthe TV to the correct video setting The pictures that are stored on the memory card appear on the TV screen NOTE You may need to adjust the Video Out preference on the camera Refer to
39. t the mode dial to Preferences 2 Tumonthe camera The LCD displays the Preferences screen 5 4 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide 3 Press the Y button until the Date Stamp icon shown below is highlighted 4 Press the Do It button The LCD displays the main Date Stamp screen The current setting is checked 7 Bate Stomp 5 Pressa or Y button until the appropriate date stamp order is highlighted 6 Press the Do It button The main Preferences screen reappears The next time you take a picture the date stamp appears in the lower right hand comer of the picture on the LCD screen NOTE The date stamp is visible after the picture has been taken with the camera in either Review mode or in Capture mode with Quickview activated The date stamp cannot be removed from that picture To tum off a date stamp press a A or Y button until OFF is highlighted and then press the Do It button The Date Stamp setting is maintained until another setting is selected This setting does not change when the camera is tumed off File Type The File Type screen selects how the picture file is saved in a FlashPix or J PEG default setting format Select a format that is compatible with the software you use on your computer NOTE The Picture Easy software Dell installed on your system for use with the digital camera supports both formats Adjusting Camera Settings 5 5 To set the fil
40. the camera s memory when the bat tery is removed Shutter button does not work Camera is not turned on Mode dial is not set to Capture Ready light is blink ing Camera is pro cessing picture The status display reads Full The memory card is full Camera is con nected to the computer Turn on the camera and verify that the green Ready light turns on Set the mode dial to Capture Wait until Ready light stops blinking before attempting to take another picture Transfer pictures to your computer or insert a memory card that has available memory Disconnect camera from computer Camera does not tum on Batteries are not properly installed Batteries are weak or dead Remove the batteries and install them according to the directions on the out side of the battery door Install new batteries Part of the picture is missing Something was blocking the lens when you took the picture Your eye or the picture was not centered correctly in the viewfinder Keep hands fingers or other objects away from the lens when taking pictures Leave space around the subject when centering the picture in the viewfinder 72 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide Problem Cause Solution Picture is too dark Flash is not on or did not go off The subject is too far away from the flash The subject is in front of a bright light Tum
41. tton The Take a Picture screen appears 6 Inthe viewfinder center the area in which you want to lock the exposure 7 Press the shutter button to lock in the exposure setting The Exposure Lock setting automatically resets when the camera is turned off Adjusting Camera Settings Using the Status Display The status display located at the top of your camera allows you to view and change some camera settings The following sections offer detailed descriptions of status display settings NOTE The camera must be turned on to view the status display 3 4 KODAK DIGITAL SCIENCE DC210 Plus Zoom Camera User s Guide Quality icon Resolution icon Pictures Remaining icon Battery Laa RO Status icon IE Lt ann I Self Timer icon v as LOI Flash icon a E Oa Close Up icon Card Status icon Red eye Reduction icon Pictures Remaining The Pictures Remaining icon changes automatically to indicate the remaining number of pictures that can be stored at the current quality and resolution setting You may not select or change the Pictures Remaining icon When the card s memory is full the status display indicates Full You must delete exist ing pictures or change memory cards to capture additional pictures To save pictures transfer them to your computer before deleting them For more information on how to move or delete pictures see Deleting the Picture J ust Taken found earlier in this chapter
42. ures stored on the memory card Using the Overlay screen the camera can per form the following functions e View the amount of unused memory left on the memory card e View thumbnails of the pictures Delete one or all pictures from the memory card View pictures and run a slide show from the camera on your TV NOTE To conserve battery life Dell recommends that you use the AC adapter with the camera when it is in Review mode Viewing Pictures on the Camera To view pictures on the camera perform the following steps 1 Set the mode dial to Review 2 Tumonthe camera The Overlay screen appears on the LCD screen with the last picture taken mode dial LCD screen Reviewing Pictures 4 1 3 Pressthe 4 and gt buttons to scroll through the pictures To continuously scroll hold down one of these buttons The memory bar displays the space left on the memory card and the current picture position Overlay icon highlighted picture from center of filmstrip Delete icon Magnify icon filmstrip of ey LS pictures on memory card To exit the Overlay screen press the or Y button to highlight the Overlay icon Then press the Do t button to tum off the Overlay screen The main Review screen reappears Deleting Pictures You can delete one or all of the pictures on the memory card when in the Review mode To delete a picture in Review mode perform the following steps 1 Set the mode dial to Review 2 Tum
43. w screen The current setting is checked A Y Y COD Press a 4 or Y button until ON is highlighted Press the Do It button The main Preferences screen reappears The next time you take a picture it appears for a moment on the LCD screen To tum off Quickview press a 4 or Y button until OFF is highlighted and then press the Do It button The Quickview setting is maintained until another setting is selected This setting does not change when the camera is tumed off Date and Time The Date and Time screen sets the camera s date and time To set the date and time per form the following steps 1 2 Set the mode dial to Preferences Tum on the camera The LCD displays the Preferences screen Adjusting Camera Settings 5 7 3 Press the Y button until the Date Time icon shown below is highlighted on the Pref erences screen 4 Press the Do It button The LCD displays the main Date Time screen with the current date and time listed Press a 4 or button to highlight the day month year hour or minute setting Press a 4 or Y button to adjust the setting Repeat steps 5 and 6 until the information is correct DION po U Press the Do It button The main Preferences screen reappears The date and time setting is maintained until another setting is selected This setting does not change when the camera is tumed off NOTE If you remove the batteries from
Download Pdf Manuals
Related Search