Kobe Range Hoods RA9436SQF User's Manual
Contents
1. 8 Connect three wires black white and green to house wires and cap with wire connectors Connect according to color black to black white to white and green to green as shown in Figure 8 Figure 8 9 Test the operation of the hood before performing the next step Make sure power is supplied to the hood Duct Cover Installation 10 Slide inner duct cover up 2 inches before sliding entire duct cover onto the hood Figure 9 11 Align the inner duct cover to the duct cover mounting bracket Secure inner duct cover with two 4x8 mm screws provided Fasten outer duct cover to plastic plate on the hood with four 4x8 mm screws provided Install Accessories 13 Place aluminum baffle filters underneath the hood Refer to Figure 10 Final Assembly 14 15 Turn power ON in control panel Check all lights and fan operation leave this Installation Instructions and Operation Manual for the homeowner Figure 9 Figure 10 OPERATION INSTRUCTIONS This KOBE hood is equipped with four electronic controls with a 10 second standby startup amp 30 second delay shutoff one powerful centrifugal squirrel with baffle or aluminum filters and two bright 12 volt 20 watt halogen lights The four electronic controls are Light Control Speed Control A Speed Control B and the Power Control On Off Refer to Figure 11 Figure 11 Light Control Power Control Speed Control A Speed Control B2. For service please contact KOBE Range Hoods Inc 4934 Walnut Grove Avenue Suite 202 San Gabriel CA 91776 U S A Tel 626 309 1356 Fax 626 309 1366 Email customerservice koberangehoods com www KobeRangeHoods com 17 PRODUCT REGISTRATION Register Your Product Any covered failure occurring within two years of original purchase arising from defective workmanship or material in manufacture will be repaired or at our option replaced free of charge by an authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable Keep proof of purchase original invoice handy for inspection If the range hood is sold by the original purchaser during the warranty period the new owner is protected until the expiration of the original purchaser s warranty See warranty section for complete warranty coverage information This appliance has been manufactured tested and inspected to the standards required by KOBE Range Hoods PLEASE MAIL IN YOUR WARRANTY REGISTRATION CARD AND PROOF OF PURCHASE TO KOBE Range Hoods Inc 4934 Walnut Grove Avenue Suite 202 San Gabriel CA 91776 RECORD THE FOLLOWING INFORMATION FOR YOUR RECORD Model No Serial No Purchased Date Purchased From IMPORTANT PLEASE KEEP A COPY OF YOUR SALE RECEIPT OR INVOICE HANDY WHEN REQUESTING FOR SERVICE 18
3. 1 Using references in Table 1 and measurements on Page 11 mark the leveling locations point for hood mounting bracket on the wall 2 Secure two mounting screws not provided to the wall leaving an 1 8 space from the wall Figure 5 o 3 Align the hood mounting bracket to the mounting screws on the wall and hang EEDD hood into place View from back of the hood Rubber Stand 4 Secure and tighten the mounting screws Figure 5 CAUTION MAKE SURE THE HOOD IS SECURE BEFORE RELEASING Ductwork Installation 5 Using Reference E from Table 1 and measurements on Page 11 mark the leveling point for duct cover mounting bracket 6 Secure the duct cover mounting bracket to the wall with two screws not provided Figure 6 Make sure all screws are tightened NOTE Inner duct cover will Figure 6 cover the duct cover mounting bracket 7 _ Use aluminum or steel pipe not provided to connect the plastic exhaust on the hood to the ductwork above Use duct tape to ensure all joints are secure and air tight as shown in Figure 7 Wiring to Power Supply SAFETY WARNING RISK OF ELECTRICAL SHOCK THIS RANGE HOOD MUST BE PROPERLY GROUNDED MAKE SURE THIS IS DONE BY A SPECIALIZED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL Aluminum nr CODES BEFORE CONNECTING WIRES ARE SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY Figure
4. TURN ON e Press Power Control On Off button once Note If any control button is not pressed within 10 seconds power will be automatically turned off e The KOBE hood will start on Low speed Each press of the Speed Control button will cycle through the various speeds e Press Speed Control A button to cycle from Low Medium High or QuietMode Press Speed Control B button to cycle from Low QuietMode High or Medium Note Speed Control A or B will operate both fans e Press Light Control button to turn on halogen light TURN OFF e Press Power Control On Off button once panel lights will flash and power will be completely shut off after 30 seconds OR e Press Power Control On Off button twice and all power will be completely shut off immediately e If only the lights are on pressing Power Control On Off button once will turn power off after 30 seconds MAINTENANCE For the optimal level of operation clean the range hood surface and filters regularly To Clean Hood Surface CAUTION NEVER USE ABRASIVE CLEANERS PADS OR CLOTHS Regular care will help preserve your KOBE Range Hood s fine appearance 1 Use only mild soap or detergent Dry surface using a soft cloth If hood looks splotchy stainless steel hood use an orange base cleaner to clean the surface of the hood Avoid getting cleaner on the control switches Use a damp towel to get rid of any cleaning solution Use dry soft cloth to dry the
5. KORBE KOBE Brand Range Hood Model No RA9436SQF RA9436SQB RA 094 SERIES INSTALLATION INSTRUCTIONS AND OPERATION MANUAL READ AND SAVE THESE INSTRUCTIONS CONTENTS Important oaret IMS MU CIA i Ei 1 Conibonent orP acKade su eneu ee 3 A RNN i 4 Operation INS TUCASA liada 8 Maintenance it calls 9 PD CCIM e tc a 30 10 Measurements amp Diagrams 11 RESULISE RNN 12 CIRCUIT DIO am RY ta dene au 14 RI e ele ae ae eek 15 W TEG A A A 16 Product Redal een dois 18 READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING ALL WIRING MUST BE DONE BY A PROFESSIONAL AND IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES KE 221547 kv 071505 IMPORTANT SAFETY INSTRUCTIONS PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION bwarninG TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR PERSONAL INJURY OBSERVE THE FOLLOWING 1 Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards including fire rated construction 2 When cutting or drilling into wall or ceiling be careful not to damage electrical wiring or other hidden utilities 3 Ducted fans must be vented to the outside a Before servicing or cleaning unit open the light panel and SWITCH POWER OFF AT SERVICE PANEL b Clean fan baffles filters and grease laden surfaces frequently To reduce the risk of fire and to disperse air properly m
6. LING CLEANING OR SERVICING NOTE BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER DAMAGE TO THE HOOD MAY OCCUR Preparation before Installation Figure 1 NOTE TO AVOID DAMAGE TO YOUR HOOD PREVENT DEBRIS FROM ENTERING THE VENT OPENING Decide the location of the venting pipe from the hood to the outside Figure 1 A ls DUCT COVER A straight short venting run will allow the hood to perform more efficiently Try to avoid as many transitions elbows and long run as possible This may reduce the performance of the hood Figure 2 Temporarily wire the hood to test for proper operation before installing Refer to step 8 4 9 and figure 8 on page 6 WALL STUDS Important Peel any protective film off the hood Use duct tape to seal the joints between pipe sections If necessary prepare back wall frame with cross framing lumber for secure installation Refer to Table 1 and measurements on Page 11 to decide the level of the lumber Figure 2 Loosen hood mounting brackets at the back of the hood adjust brackets and tighten screws as shown in Figure 3 If necessary remove the rubber stand on the back of the hood and discard Figure 4 Hood Installation CAUTION If it is necessary to move the cooking range to install the hood be sure to turn off the power on an electric range at the main electrical box SHUT OFF THE GAS BEFORE MOVING A GAS RANGE _ HOOD Figure 3 Hood Mounting Brackets Figure 4
7. Light BF 9436 Aluminum Filter AF 9436 C1 0604 0101 H T 9 12 MODEL NO RA9436SQF RA9436SOB Complete Set Model No RA9436SQF Required RA 9436 amp AF 9436 Model No RA9436SOB Required RA 9436 amp BF 9436 ITEM NO RA 9436 13 ITEM NO BF 9436 e ITEM NO AF 9436 gt CIRCUIT DIAGRAM MODEL NO RA9436SQF RA9436SOB Power Blue Low Low Ch Ground Capacitor ial Brown Transformer Motor es ED o o D E OU S White Blue Black White White c B B Eaa Z EL Bap E op as eee m O gt O rc m 0 14 DISCLAIMER 1 CAREFULLY INSPECT ALL ITEMS FOR DAMAGES BEFORE ACCEPTING DELIVERY NOTE ANY DAMAGES ON THE FREIGHT BILL OR EXPRESS RECEIPT REQUEST NAME AND SIGNATURE OF THE CARRIER S AGENT AND KEEP COPY TO SUPPORT YOUR CLAIM Upon acceptance of items owner assumes responsibility for its safe arrival Report damages to the carrier and file a claim immediately Failure to do so may result in the denial of your claim The carrier will furnish you with necessary forms for filing a claim DAMAGES CAUSED DURING TRANSIT ARE NOT COVERED UNDER OUR WARRANTY PLEASE INSPECT CONTENTS OF PACKAGE S CAREFULLY UPON RECEIPT We must be notified in writing of any damages and or missing parts within the allocated days upon your receipt of package s Contact your local KOBE dealer or distributor or call KOBE for the time limi
8. MES with a close fitting lid cookie sheet or metal tray and then turn off the burner KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES If the flames do not go out immediately EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911 e NEVER PICK UP A BURNING PAN You May Get Burned e DO NOT USE WATER including wet dishcloths or towels a violent steam blast will result e Use an extinguisher ONLY if a You have a Class A B C extinguisher and know how to operate it b The fire is small and contained in the area where it started c The fire department has been called d You can fight the fire with your back to an exit What to Do If You Smell Gas e Extinguish any open flame e Do not try to turn on the lights or any type of appliance e Open all doors and windows to disperse the gas If you still smell gas call the Gas Company and Fire Department right away d caution 1 For general ventilation use only Do not use to exhaust hazardous or explosive materials and vapors 2 To reduce the risk of fire use only metal ductwork 3 Follow the heating eguipment manufacturer s guideline and safety standards such as those published by the National Fire Protection Association NFPA and the American Society for Heating Refrigeration and Air Conditioning Engineers ASHRAE and code authorities Activating any switch on may cause ignition or an explosion A WARNING ELECTRICAL SHOCK HAZARD Can result in serious i
9. S MODEL SIZE COLOR CONSUMPTION AMPERE VOLTAGE NUMBER OF MOTORS DESIGN FAN TYPE EXHAUST CONTROLS HALOGEN LIGHTS HOOD DIMENSION W x D x H OPTIONAL ACCESSORIES W x D x H WEIGHT Ibs SPEED Air Capacity cfm Sone RA9436SOF 36 RA 9436 AF 9436 RA9436SOB 36 RA 9436 BF 9436 304 Commercial Grade Stainless Steel 215W 1 79A 120V 60Hz 1 18 Gauge Seamless Satin Finish Squirrel Cage Top 6 Round Electronic Control 4 Buttons 10 Second Standby Startup 30 Second Delay Shutoff RAI436SQF 12V 20W x 2 RA9436SOB 12V 20W x 2 RA9436SQF 35 1 4 x 20 1 2 x 12 1 4 RA9436SQB 35 1 4 x 20 1 2 x 12 1 4 1 Model No RA0931DC 1 Piece Extension Duct Cover for 9 10 Ceiling 2 Model No RA0946DC 1 Piece Extension Duct Cover for 10 11 Ceiling 3 Model No SSP36 36 Stainless Steel Back Panel 36 x 1 10 Net Gross RA9436SOF 37 5 46 0 RA9436SOB 46 0 53 0 QuietMode Low Medium High 280 420 580 760 1 2 2 0 2 9 4 5 In House Test Static Pressure 0 One sone is equivalent to the sound of a refrigerator at 40 decibels Specifications subject to change without notice 10 MEASUREMENTS 8 DIAGRAMS Bottom View O O 20 1 2 25 32 Mn 35 1 4 1 1 4 12 1 4 PARTS LIST MODEL NO RA9436SQF RA9436SOB NO DESCRIPTION MODEL SIZE PART NO RA9236DC iri z C1 0404 4001 Transformer
10. ake sure to vent air outside DO NOT vent exhaust air into wall spaces attics crawl spaces or garages NOTE This warranty is invalid without an authorized agent s receipt or if unit is damaged due to misuse poor installation improper use mistreatment negligence or any other circumstances beyond the control of KOBE RANGE HOODS authorized agents Any repair carried out without the supervision of KOBE RANGE HOODS authorized agents will automatically void the warranty KOBE RANGE HOODS will not be held responsible for any damages to personal property or real estate or any bodily injuries whether caused directly or indirectly by the range hood WARNING TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF A RANGE TOP GREASE FIRE 1 Keep fan baffle filter if any and grease laden surfaces clean 2 Always turn hood ON when cooking at high heat 3 Use high settings on cooking range ONLY when necessary 4 Do not leave cooking range unattended when cooking 5 Always use cookware and utensils appropriate for the type and amount of food prepared 6 Use this unit only in the manner intended by the manufacturer 7 Before servicing switch power off at service panel and lock service panel if possible to prevent power from switching on accidentally 8 Clean ventilating fans frequently Grease should not be allowed to accumulate on fan and baffles filters What to Do In The Event Of a Range Top Grease Fire e SMOTHER FLA
11. hood To bring the glow back into a stainless steel finish use a stainless steel cleaner DO NOT allow deposits to remain for long periods of time DO NOT use ordinary steel wool or steel brushes Small bits of steel may adhere to the surface causing rust 6 DO NOT allow salt solutions disinfectants bleaches or cleaning compounds to remain in contact with stainless steel for extended periods Many of these compounds contain chemicals which may be harmful Rinse with water after exposure and wipe dry with a clean cloth nr To Clean Aluminum Baffle Filter CAUTION DRAIN OIL FROM BAFFLE FILTERS BEFORE OIL OVERFLOW 1 Remove all the aluminum baffle filters 2 Wash with warm soapy water Dry completely before returning into place Note Baffle Filters are top rack dishwasher safe To Replace Light Bulb CAUTION HALOGEN LIGHT UNIT MAY BE HOT HALOGEN LIGHT GLASS COVER HALOGEN LIGHT HOUSING HALOGEN LIGHT BULB 12V 20W 1 Make sure all controls are OFF and range hood is unplugged 2 Place the flat head screwdriver into the groove between the halogen light glass cover and light housing 3 Pop outthe halogen light glass covering 4 Gently pull out the defective light bulb and discard Light bulbs should be 12V 20W maximum 5 Using a cloth hold the new light bulb and push securely into light socket 6 Return halogen light glass cover to the housing 7 Turn range hood ON to test for operation SPECIFICATION
12. njury or death Disconnect appliance from electric power before servicing If equipped the fluorescent light bulb contains small amounts of mercury which must be recycled or disposed of according to Local State and Federal Codes m a COMPONENTS OF PACKAGE Must keep all material for returns or refunds BOX 1 OF 2 BOX 2 OF 2 Item No RA 9436 REOUIRED ONE OF THESE ITEM Item No BF 9436 Model No RA9436SOB O KOBE Range Hood 1 Warranty Registration Card 1 Instructions Manual 1 o Hood Mounting Bracket 2 O Screws Package 1 O Baffle Filter 3 Baffle Handle 3 O Screws Package 1 M 4 x 8 mm 6 pcs Item No AF 9436 Model No RA9436SOF A Aluminum Filter 3 el fi g M 4 x 8 mm 6 pcs Attached to Hood INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation To calculate the length of the installation please refer to Table 1 All calculations are measured in inches TABLE 1 A Height of Floor to Ceiling B Height of Floor to Counter Top Standard 36 C Preferred Height of Counter Top to Hood Bottom Recommended 27 to 30 D Height of Hood E Height of the Hood Installation A B C F Height of Duct Cover E D dA sarre WARNING HOOD MAY HAVE VERY SHARP EDGES PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTAL
13. p or material in manufacture will be repaired or replaced at our own discretion free of charge by an authorized KOBE Range Hoods agent or KOBE Range Hoods as applicable Keep proof of purchase or original invoice handy for inspection If the range hood is sold by the original purchaser during the warranty period the new owner is protected until the expiration of the original purchaser s warranty CONDITIONS The following conditions apply only in relation to the warranty expressly given in this certificate 1 This warranty applies only a within U S A and Canada b to range hoods used for PRIVATE SINGLE FAMILY USE if used for COMMERCIAL or MULTIPLE FAMILY USE or other purposes warranty will be voided 2 Repair of any fault under this warranty shall not be provided a if the identification number attached to the range hood has been removed altered or rendered illegible b if notice of the defect has not been given within the period applicable c for failure of light bulbs d for physical damage e for surfaces damaged by use of improper chemical cleaning agents f if the appliance has been i subject to misuse abuse negligence accident incorrect installation or failure to follow the operating instructions ii connected to improper inadequate or faulty electricity service exhaust ducts or duct cover or operated using incorrect or contaminated lubricants iii installed maintained or operated not in accordance with the in
14. structions furnished by KOBE Range Hoods including the improper use of detergents bleaches or cleaners g for damage to range hood during transit delivery installation or removal h for damage by or resulting from attempted repairs conducted by anyone other than KOBE Authorized Service Agent 3 The purchaser shall be responsible for any expenses involved in making the range hood readily accessible for servicing and service to range hood installed outside the main sales territory of the retailer or service territory of the nearest approved KOBE Range Hoods Agent as applicable for any traveling expenses and costs of transporting the range hood or parts thereof to and from the dealer or Service Agent 4 The purchaser must produce proof of purchase and this warranty certificate when making the claim 16 5 Damages caused during shipment are not covered under our warranty CONSEQUENTIAL DAMAGE The warrantor is not responsible for any consequential damage UNLESS YOU LIVE IN A STATE THAT DOES NOT ALLOW THE EXCLUSION OF CONSEQUENTIAL DAMAGE IMPLIED WARRANTIES STATE LAW Any implied warranties including the implied warranty of merchantability and fitness for purpose imposed on the sale by the laws of the state of sale are limited to two year from the date of original purchase Some states do not allow limitations on the duration of implied warranties This warranty gives you specific legal rights which vary from state to state SERVICE
15. t CLAIMS WILL NOT BE ACCEPTED AFTER THE ALLOCATED DAYS NOTE ITEMS WERE THOROUGHLY TESTED AND CAREFULLY PACKED IN OUR FACTORY BEFORE SHIPPING Products must be returned in good working condition with ALL original parts and documentation packed in ALL original cartons fillers and shipping cartons A restocking fee of 25 will be charged for all approved items EXCHANGES OR RETURNS MAY NOT BE ACCEPTED IF ANY PACKAGING IS MISSING MAKE SURE TO INSPECT THE HOOD FOR DAMAGES AND DEFECTS BEFORE INSTALLATION Appearance flaws of the hood found after installation and not affecting hood performance is not covered under our warranty for returns or exchanges Service visits not covered under warranty will carry a service charge A Before Installation Return for exchange or refund please see above for acceptable returns B After Installation NO exchange or refund 15 WARRANTY WARRANTY CERTIFICATE KOBE Range Hoods Inc warrants all products manufactured or supplied by it to be free from defects in workmanship and materials lts obligations pursuant to this warranty are limited to a period of two years from the date of purchase and to the repair or replacement at its option and subject to the terms and conditions stated below of any component which its examination shall disclose to be so defective TWO YEAR WARRANTY SERVICE PERIOD Any warranted failure occurring within two years of original purchase arising from defective workmanshi
Download Pdf Manuals
Related Search