Klipsch IC - SW - 8 T 2 User's Manual
Contents
1. N G SUBWOOFER IC SW 8T 2 SPECIFICATIONS IC SW 8T2 FREQUENCY RESPONSE 50 130 Hz A dB CONT POWER HAND 150 watts 27 V CALC MAX CONT OUTPUT IM 111 dB SENSITIVITY 2 83 V 1M 92 dB COVERAGE N A DI N A Q N A NOMINAL IMPEDANCE 6 ohms min 4 9 ohms switch set to mono or stereo position DIAMETER 14 125 CUTOUT DIAMETER 14 25 OVERALL DEPTH 13 625 MOUNTING DEPTH 13 313 WEIGHT 23 lbs INPUT CONNECTORS Terminal Strip TRANSFORMER TAPS 70V 60W 30W 100V 120W 60W FINISHES White TRANSDUCERS 8 Woofer AND 8 Drone ENCLOSURE TUNING Bandpass via an 8 Drone 2003 Klipsch Audio Technologies All Rights Reserved Specifications Subject to Engineering Changes Klipsch Limited Warranty KLIPSCH AUDIO TECHNOLOGIES KLIPSCH warrants this product to be free from defects in materials and workmanship subject to the terms set forth below for a period of five 5 years from the date of purchase During the Warranty period KLIPSCH will repair or replace at KLIPSCH s option this product or any defective parts excluding electronics and amplifiers For products that have electronics or amplifiers the Warranty on those parts is for a period of two 2 years from the date of purchase To obtain Warranty service please contact the KLIPSCH authorized dealer from which you purchased this product If your dealer is not equipped to perform the repair of your KLI2. a 24 LU Ll O O gt ca N Z Lu U SW 8T2 IN I C OWNER S MANUAL AND WARRANTY Thank you for purchasing your Klipsch IC SW 8T2 in ceiling subwoofer The IC SW 8T2 in ceiling speaker is designed for music reinforce ment applications Unobtrusive these loudspeakers are engi neered for easy versatile installation The IC SW 8T2 features a transformer less design for 70 7V 100V distributed line systems Some of the benefits of this design are Elimintation of transformer saturation at high output levels elimination of transformer insertion losses improved bandwidth particularly at low frequencies and improves power transfer to the loudspeaker at low frequencies For applications where 4 ohm mono or 8 ohm stereo operation is required the mode of operation can be selected by using an optional connection located on the back input terminal and by properly setting the rotary switch located under the grill Before installing your speakers take a moment to check the contents of the cartons and make sure nothing has been damaged in transit Contents Description QUANTITY Speaker Module Grille Reinforcement Ring Rails 2 Cardboard Cutout Template and Paint Mask Screws Attach Rails to Reinforcement Ring 2 3 8 Adapter Fittings l Adapter Fittings Installation Guidelines The IC SW 872 includes a tilebridge for use when installing the loudspeaker into suspended ceilings or wherever additi
3. PSCH product it can be returned freight paid to KLIPSCH for repair Please call KLIPSCH at 1 800 KLIPSCH for instructions You will need to ship this product in either its original packaging or packaging affording an equal degree of protection Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that this product is within the Warranty period must be presented or included to obtain Warranty service This Warranty is invalid if a the factory applied serial number has been altered or removed from this product or b this product was not purchased from a KLIPSCH authorized dealer You may call 1 800 KLIPSCH to confirm that you have an unaltered serial number and or you purchased from a KLIPSCH authorized dealer This Warranty does not cover cosmetic damage or damage due to misuse abuse negligence acts of God accident commercial use or modification of or to any part of the product This Warranty does not cover damage due to improper operation maintenance or installa tion or attempted repair by anyone other than KLIPSCH or a KLIPSCH dealer which is authorized to do KLIPSCH warranty work Any unau thorized repairs will void this Warranty This Warranty does not cover product sold AS IS or WITH ALL FAULTS REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE REMEDY OF THE CONSUMER KLIPSCH SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED
4. WARRANTY ON THIS PRODUCT EXCEPT TO THE EXTENT PROHIBITED BY LAW THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES WHATSOEVER INCLUDING BUT NOT LIMITED TO THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PRACTICAL PURPOSE Some states do not allow the exclusion or limitation of incidental or consequential damages or implied warranties so the above exclusions may not apply to you This Warranty gives you specific legal rights and you may have other rights which vary from state to state 3502 Woodview Trace Suite 200 Indianapolis Indiana 46268 USA 1 800 KLIPSCH e www klipsch com 193152 1003
5. onal reinforcement of the ceiling material is required The tilebridge and loudspeaker are designed such that installation may be accomplished where access above the ceiling is not possible or may be difficult Installation 1 The tilebridge is composed of three parts a reinforcement ring and two rails The two rails should be attached to the reinforcement ring using the two included screws as shown below Caution Be sure to comply with any and all building codes in your area 2 To install your IC SW 8T2 cut out a hole in the ceiling using either the cardboard cutout template provided with your speak ers or consult the measurements below Pull wiring through hole IC SW 8T2 12 5 Round 3 To install the tilebridge fold the rail side of the ring back upon itself using the spring tensioner on the reinforcement ring to allow insertion into the cutout hole Once it is inserted into the cutout hole release the reinforcement ring such that it unfolds back to its normal position Position tilebridge over cutout hole 4 The wiring compartment is intended as a termination point for the audio circuit Access to this compartment is gained by removing the terminal cover located on the back of the speaker The terminal cover will accept the appropriate conduit wire adapter provided Feed wires through conduit wire adapter and connect to the input terminal according to the desired operation mode Be sure to observe proper polarity Re
6. place the terminal cover and tighten the conduit wire adapter to secure the wire Caution When connecting 70V or 100V distributed line systems take care to ensure proper terminal connection Connection to the low impedance termi nal could result in speaker damage amplifier damage or both 70 100v 5 Insert the speaker into the cutout hole With a 2 Phillips screw 6 For installations using 70v 100v input connection set the driver tighten the four dog clamps until they are seated securely switch on the front panel to 70V 100V against the ceiling surface Do not overtighten For low impedance stereo applications the switch should be set to 8 ohms stereo For low impedance mono applications the switeh should be set to 4 ohm mono In all cases please make sure the speaker wires are connect ed to the appropriate terminal on the back Stereo 4 el Mono Stereo IC SW 8T2 tap selectable 7 Using the flat of your hand insert grille into soeaker frame making sure it is securely seated and flush Seismic Tab A seismic tab located on the back of the speaker is used as a secondary security point Some construction codes may require its use To utilize the seismic tab run a support wire from a secure point in the ceiling and attach it to the tab Be sure to consult the construction codes in your area Klipsch recommends the use of this tab in all installations as a secondary means of support
Download Pdf Manuals
Related Search