Kenwood DDX 5026 Installation Guide
Contents
1. ANT cont P CONT GPS Antenna Accessory 3 see page 8 tl Accessory AWARNING Connecting the ISO Connector he pin arrangement for the ISO connectors depends on the type of vehicle you drive Make sure to make the proper connections to prevent damage to the unit The default connection for the wiring harness is described i below If the ISO connector pins are set as described 2 make the connection as illustrated lease be sure to reconnect the cable as shown 2 below to install this unit to the Volkswagen vehicles etc Default setting The A 7 pin red of the vehicle s ISO connector is linked with the ignition and the A 4 pin yellow is connected to the constant power supply Ignition cable Red A 7 Pin Red ng Unit tese Vehicle Le Battery cable Yellow A 4 Pin Yellow The A 7 pin red of the vehicle s ISO connector is connected to the constant power supply and the A 4 pin yellow is linked to the ignition Ignition cable Red A 7 Pin Red Vehicle Bu s Battery cable A 4 Pin Yellow Yellow gt Unit gt English 5 System Connection USB device USB terminal commercially available o Cie Rear View Camera input Visual input Yellow Audio Visual output Visual output Yellow Audio left output White Aud2. KENWOOD GPS NAVIGATION SYSTEM DNX SERIES DNX5260BT MONITOR WITH DVD RECEIVER DDX SERIES DDX5026 DDX5056 INSTALLATION MANUAL Kenwood Corporation B54 4763 00 00 EW QW Accessories Accessory of DNX5260BT This accessory is used when connecting an external device to AV IN jack on the front panel of this unit For how to use this accessory refer to the instruction manual of this unit 2 DNXSERIES DDX SERIES Installation Procedure 1 To prevent short circuits remove the key from the ignition and disconnect the O terminal of the battery 2 Make the proper input and output wire connections for each unit 3 Connect the wire on the wiring harness 4 Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle 5 Take Connector A on the wiring harness and connect it to the external power connector on your vehicle Connect the wiring harness connector to the unit Install the unit in your car Reconnect the O terminal of the battery Press the reset button oo So AWARNING If you connect the ignition wire red and the battery wire yellow to the car chassis ground you may cause a short circuit that in turn may start a fire Always connect those wires to the power source running through the fuse box Acquiring GPS Signals The first time you turn on DNX5260BT you must wait while the system acquires satellite
3. gs will inhibit the cooling of the internal temperature and result in malfunction Cooling fan Reception may drop if there are metal objects near the Bluetooth antenna DNX5260BT only Bluetooth antenna unit othe Ie o el js Q i IN CAUTION Install this unit in the console of your vehicle Do not touch the metal part of this unit during and shortly after the use of the unit Metal part such as the heat sink and enclosure become hot English 3 Connection Connector Function Guide Pin Numbers for Cable Colour Functions ISO Connectors External Power Connector A 4 Yellow Battery A5 Blue White Power Control A 6 Orange White Dimmer A 7 Red gnition ACC A 8 Black Earth Ground Connection Speaker Connector B 1 Purple Rear Right B 2 Purple Black Rear Right B 3 Gray Front Right FM AM antenna B 4 Gray Black Front Right Antenna Cord input JASO B 5 White Front Left B 6 White Black Front Left B 7 Green Rear Left B 8 Green Black Rear Left C Connector A Battery wire Yellow lani ire Red o 1516 12 12 gnition wire Red WBE Cent LES 542 Orange White Dimme
4. io right output Red Visual input iPod AV input 2 switchable Resistance free mini plug 3 59 Audio input iPod AV input 2 switchable Resistance free stereo type mini plug 3 59 6 O Ore Aud ront Aud Aud Preout io left output White io right output Red Preout io left output White io right output Red b fi er Preout a Aud 6 DNX SERIES DDX SERIES io left output White io right output Red Optional Accessory Connection iPod commercially available Kc KCA iP301V Optional Accessory Audio Output Black Navigation System Optional Accessory ti pd KCA BT200 Optional Accessory input DDX5026 DDX5056 only Connection cable Included in the Navigation System TV Tuner Optional Accessory bajen nu E Navigation units that can be connected to this unit As of December 2009 KNA G620T For latest information access the www kenwood com cs ce 1 5c 57x N S11 Connection cable Included in the TV tuner English 7 Installing the GPS Antenna DNX5260BT only GPS antenna is installed inside of the car It should be installed as horizontally as possible to allow easy reception of the GPS satellite signals To mount the GPS antenna inside your vehicle 1 Clean your da
5. nition i e it will not turn on and off along with the ignition If you want to link the unit s power with the ignition connect the ignition wire to a power source that can be turned on and off with the ignition key Use a commercially available conversion connector if the connector does not fit in the vehicle connector Insulate unconnected wires with vinyl tape or other similar material To prevent a short circuit do not remove the caps on the ends of the unconnected wires or the terminals If the console has a lid make sure to install the unit so that the faceplate will not hit the lid when closing and opening If the fuse blows first make sure the wires aren t touching to cause a short circuit then replace the old fuse with one with the same rating Connect the speaker wires correctly to the terminals to which they correspond The unit may be damaged or fail to work if you share the wires or ground them to any metal part in the car After the unit is installed check whether the brake lamps blinkers wipers etc on the car are working properly Mount the unit so that the mounting angle is 30 or less Do not press hard on the panel surface when installing the unit to the vehicle Otherwise scars damage or failure may result This unit has the cooling fan to decrease the internal temperature Do not mount the unit in a place where the cooling fan of the unit are blocked Blocking these openin
6. r control wire Orange White 1745 BI s0 gt Connector B zn E Connect to the vehicle s parking brake detection switch harness Parking sensor wire Light Green PRKSW Eor the sake of safety be sure to connect the parking sensor bs Connect to vehicle s reverse lamp harness when Reverse sensor wire Purple White using the optional rear view camera Steering remote control wire Light Blue Yellow To steering remote E To use the steering wheel remote control feature you need to an exclusive remote adapter not supplied matches your car is required When this terminal is not in use leave its cap on Connect to the terminal that is grounded when either Mute control wire Brown the telephone rings or during conversation E To connect the Kenwood navigation system consult your navigation manual Power control Motor antenna control wire Blue White Connect either to the power control terminal when using the optional power amplifier or to the antenna control terminal in the vehicle If no connections are made do not let the cable come out from the tab 4 DNXSERIES DDX SERIES Bluetooth Microphone ET E Accessory see page 8 FUSE 15A REVERSE STEERING WHEEL REMOTE CONT REMOTE INPUT MUTE
7. shboard or other surface 2 Peel the backing off of the adhesive on the bottom of the metal plate accessory Press the metal plate accessory down firmly on your dashboard or other mounting surface You can bend the metal plate accessory to conform to a curved surface if necessary 4 Place the GPS antenna accessory on top of the metal plate accessory e Accessory 3 CA AN Depending on the type of car reception of the GPS satellite signals might not be possible with an inside installation The GPS antenna should be installed at a position that is spaced at least 12 inch 30 cm from cellular phone or other transmitting antennas Signals from the GPS satellite may be interfered with by these types of communication Painting the GPS antenna with metallic paint may cause a drop in performance 8 DNXSERIES DDX SERIES Installing the Microphone Unit DNX5260BT only Check the installation position of the microphone accessory Q 2 Remove oil and other dirt from the installation surface 3 Install the microphone 4 Wire the cable up to the unit with it secured at several positions using tape or the like Accessory Q Fix a cable with a commercial item of tape Peel the release coated paper of double face adhesive tape to fix on the place shown above Adjust the direction of the microphone to the driver Install the microphone as far as pos
8. sible from the cell phone Installation for Monitor Player Unit Installing the Escutcheon 1 Attach accessory to the unit Accessory E Installing the Monitor Player Unit Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place Make sure that the unit is installed securely in place If the unit is unstable it may malfunction eg the sound may skip English 9 Removing Monitor Player Unit Removing the Hard Rubber Frame escutcheon 1 Engage the catch pins on the removal tool 6 and remove the two locks on the lower level Lower the frame and pull it forward as shown in the figure gt Accessory 6 The frame can be removed from the top side in the same manner 2 When the lower level is removed remove the upper two locations 10 DNXSERIES DDX SERIES Removing the Unit 1 Remove the hard rubber frame by referring to the removal procedure in the section Removing the Hard Rubber Frame 2 Insert the two removal tools 6 deeply into the slots on each side as shown 3 Lower the removal tool toward the bottom and pull out the unit halfway while pressing towards the inside Be careful to avoid injury from the catch pins on the removal tool 4 Pull the unit all the way out with your hands being careful not to drop it English 11 KENWOOD
9. signals for the first time This process could take up to several minutes Make sure your vehicle is outdoors in an open area away from tall buildings and trees for fastest acquisition After the system acquires satellites for the first time it will acquire satellites quickly each time thereafter After the Installation After the installation perform the Initial Setup by referring to the instruction manual A Mounting and wiring this product requires skills and experience For safety s sake leave the mounting and wiring work to professionals Make sure to ground the unit to a negative 12V DC power supply Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing Do not use your own screws Use only the screws provided f you use the wrong screws you could damage the unit If the power is not turned ON PROTECT is displayed the speaker wire may have a short circuit or touched the chassis of the vehicle and the protection function may have been activated Therefore the speaker wire should be checked Make sure that all wire connections are securely made by inserting jacks until they lock completely If your vehicle s ignition does not have an ACC position or if the ignition wire is connected to a power source with constant voltage such as a battery wire the power will not be linked with the ig
Download Pdf Manuals
Related Search