Karcher HD 10/25 S VEX User's Manual
Contents
1. m Check water inlet volume see Technical Specifications m Check all supply lines to the pump for leaks or obstructions m Seek the help of Customer Service if nec essary 10 English Operating Instructions HD 10 25 S VEX Pump is leaky m Three drops per minute are allowable and can appear on the underside of the unit Seek the help of Customer Service if leaks are more serious Pump makes a knocking noise m Check all supply lines as well as the deter gent system for leaks m Evacuate air from the cleaner see Switch ing on the unit m Clean the fine filter m Seek the help of Customer Service if nec essary Detergent is not being drawn in m Set nozzle to Chem m Check detergent suction hose with filter for leaks or obstructions and clean it if neces sary m Clean renew non return valve in detergent suction hose connection m Open detergent metering valve or check it for leaks remove obstruction Also clean the venting orifice in the housing m Seek the help of Customer Service if nec essary Spare parts You will find a list of spare parts at the end of these operating instructions Warranty The warranty terms issued by our authorised marketing company are valid in every country We remedy any fault in the unit free of charge within the warranty period providing the cause of the fault proves to be a material or manu facturing error The warranty only becomes operative when2. cleaning facades terraces gardening equipment For stubborn dirt we recommend the dirt blaster as an optional accessory Safety features Relief valve with pressure switch On reducing the flow rate with the pressure and flow control the relief valve opens and part of the water runs back to the suction side of the pump lf the lever of the hand held spray gun is re leased the pressure switch switches the pump off If the lever is retracted the pressure switch switches the pump on again The overflow valve and pressure switch have been set and sealed at the factory Adjustments are made only by Customer Service Operating Instructions HD 10 25 S VEX English Preparing the unit for use Switching on the unit Unpack the unit When unpacking the unit check the con tents of the packaging If there has been any damage in transit inform the dealer Do not dispose of the packaging with the household rubbish hand it in at the appro priate collection point for recycling Check the oil level m Read the oil level displayed while unit is at a standstill The oil level must be above the two indicators Activate the oil reservoir vent m Unscrew the fastening screw of the hood and remove the hood m Cut off the tip on the cover to the oil reser voir m Fasten the unit cover Mount the accessories m Mount nozzle on the spray lance see markings on the top of the setting ring m Fit t
3. from an open container m Screw suction hose with filter Order no 4 440 238 to the water outlet m Vent the unit before using m To evacuate air from the unit unscrew the nozzle and leave the unit running until wa ter exits with no air bubbles m Switch off the unit and screw the nozzle back on Operating the unit Danger Observe the relative safety regulations when using the unit at filling stations or other high risk areas Caution N Only clean engines in places which have appropriate oil separators protection of the environment Caution N Only wash animals with the low pressure fan jet see Selecting the type of spray Operating with high pressure The unit is equipped with a pressure switch The motor only starts up when the lever is re tracted m Set the unit switch to I The indicator light will go green E Unlock the hand held spray gun and retract the lever of the gun m Adjust operating pressure and flow rate by rotating the pressure flow control infinitely variable m At the lowest flow rate the waste heat from the motor will heat the water to approx 15 C Selecting the type of spray The handgun must be closed m Rotate the housing of the nozzle until the desired symbol corresponds with the mark ing m Select pencil jet or fan jet by contactless changeover rotate the spray lance which is pointing down at an angle of approx 45 to the left or right Expla
4. your dealer has completed the reply card ac companying the sale of the unit has stamped and signed it and you have then sent the reply card to the marketing company in your coun try Should you wish to call upon the guarantee please apply to your dealer or nearest author ised Customer Service centre taking along also the accessories and bill of sale 11 Operating Instructions HD 10 25 S VEX English Technical Specifications HD 10 25 S VEX Mains connection Voltage V 380 220 Type of current Hz 3 50 3 60 Connected load kW 7 7 7 5 Supply fuse delayed action char C A 16 25 Max tolerable mains impedance Q 0 145 j0 090 Extension cable 10 m mm 2 5 2 5 Extension cable 30 m mm 4 _ Water connection Supply temperature max 60 Supply volume min l h l min 1200 20 Supply hose minimum length m 75 Supply hose minimum diameter inches 3 4 Suction height from an open container 20 C m 0 5 Supply pressure max MPa bar 1 10 Performance data Operating pressure MPa bar 3 19 30 190 Max operating overpressure safety valve MPa bar 20 9 209 Flow rate l h l min 500 1038 8 3 17 3 Detergent intake l h l min 0 80 0 1 3 Recoil force of the handgun N 62 Sound emission Sound pressure level dB A 72 EN 60704 1 Guaranteed sound pressure level dB A 87 2000 14 EC Vibrations of u
5. KARCHER HD 10 25 S VEX A T www karcher com 5 961 066 A 2006919 10 03 English Espa ol Portugu s PVCCKMM Lietuvi kai Latviski Eesti keeles Ae _ CD DESDE HD 10 25 S VEX OIL MN UN English Operating Instructions HD 10 25 S VEX Unit components For your safety Please fold out illustration page at the front 1 Hand held spray gun 2 Lever of hand held spray gun 3 High pressure hose 4 Handgun support 5 Detergent metering valve 6 Cap for detergent reservoir 7 Detergent reservoir 8 Detergent suction hose with filter 9 Fastening screw for hood 10 Unit switch 11 Hood 12 Pressure gauge 13 High pressure outlet 14 Nozzle rest 15 Water connection 16 Fine filter 17 Oil level display 18 Oil reservoir 19 Indicator light 20 Hose rest 21 Detergent reservoir vent 22 Accessories box 23 Cable holder 24 Handle 25 Nozzle 26 Marking of the nozzle 27 Spray lance 28 Pressure flow control 29 Safety catch of hand held spray gun Before you use the cleaner for the first time read these operating instructions and take special note of the accompanying booklet Safety Instructions for High Pressure Clean ers No 5 951 949 Use of the cleaner Use this unit exclusively for cleaning with high pressure jet and deter gent e g cleaning of machines vehicles buildings tools cleaning with high pressure jet without de tergent e g
6. bt or when expressly in structed to do so consult authorised Customer Service personnel Indicator light The indicator light shows the operating status green and faults red To reset m Switch off the unit switch m Wait a moment m Switch the unit back on again Operating status display m Constant green light Unit is operational m 1 x flashing green Operational readiness expired after 30 minutes The unit switched off after 30 minutes of permanent operation safety feature in the case of a burst high pressure hose Fault display m 1 x flashing red High pressure side leaking Check high pressure hose hose connections and hand held spray gun for leaks m 2 x flashing red Motor too hot Switch off the unit switch Leave unit to cool down Switch the unit back on again m 3 x flashing red Fault in the power supply Check the mains connection Check supply fuses m 4 x flashing red Current consumption too high Consult Customer Service Unit does not work m Availability time has run out The indicator light will flash green Switch the unit off and then on again m Check connecting cable for damage E Consult Customer Service if there is an electrical fault Unit does not come up to pres sure m Set nozzle to high pressure m Clean replace nozzle m Clean the fine filter replace if required m Evacuate air from the cleaner see Switch ing on the unit
7. can appear on the underside of the unit Seek the help of Customer Service if leaks are more serious Every week m Check oil level in oil reservoir if the oil is milky water in oil seek the help of Cus tomer Service immediately m Clean the fine filter Unpressurize unit Unscrew the fastening screw of the hood and remove the hood Unscrew the cover with filter Clean the filter with clean water or com pressed air Reassemble in the reverse order m Clean the filter at the suction hose for de tergent Annually or after 500 operating hours m Change the oil For oil quantity and type see Technical Specifications Undo the fastening screw remove the hood unscrew the front oil drain plug on the motor housing Drain oil into a suitable container Screw in the oil drain plug Fill slowly with fresh oil air bubbles have to escape Operating Instructions HD 10 25 S VEX English As and when required m Emptying and cleaning the detergent tank Pull out the screw cap and hose for the detergent tank Place the unit on its rear Empty and clean the detergent tank Troubleshooting Danger Before any repair work is undertaken switch the unit off and pull out the power plug Have electrical components checked and re paired only by authorised Customer Service personnel For faults which are not identified in this chap ter or when in dou
8. e handgun in the support m Reel in the high pressure hose and hang it over the hose rest or E Coil the connecting cable round the cable hose rest Frost protection Caution A Frost will destroy a unit that is not com pletely empty of water Store the unit where it will be free of frost If storage away from frost is not possible m Empty the detergent tank see care and maintenance As and when required m Drain off the water and rinse the unit through with anti freeze m Leave the unit to dry for max 1 minute m Use the standard glycol based anti freezes for cars m Follow the handling instructions of the anti freeze manufacturer Care and maintenance Danger Before any care and maintenance work on the unit draw out the mains plug Caution N When changing the oil dispose of any waste oil only at authorised collection points Safety inspection Maintenance contract You can arrange with your dealer to have a regular safety inspection carried out or to have a maintenance contract Please seek advice Before each use m Check connecting cable for damage risk of getting an electric shock have adamaged connecting cable replaced without delay by authorised Customer Service personnel or an electrician m Check high pressure hose for damage danger of explosion replace a damaged high pressure hose without delay m Check unit pump for any leaks Three drops per minute are allowable and
9. he spray lance to the hand held spray gun with pressure and flow control m Lock cable clincher into bore lateral to the handle m Tighten the high pressure hose according ly Electrical connection Caution N The voltage specified on the model rat ing plate must correspond to the voltage sup plied Caution N The maximum tolerable mains impedance at the electrical contact point see Technical Data must not be exceeded Caution N Use an extension cable with a sufficient cable cross section see Technical Specifica tions and unwind it fully from the cable drum For connected loads see model rating plate Technical Specifications Caution A It is essential that the unit is connected to the power supply by means of a plug An in separable connection to the power supply is prohibited The plug is used to disconnect from the mains Water connection Suction feed operation Connection to water main Caution DN Pay attention to the regulations of the water supply company according to DIN 1988 the unit may not be connected direct to the public drinking water supply A short term connection via a non return valve Order no 6 412 578 is allowed For connected loads see Technical Specifica tions m Connect a supply hose not supplied to the water outlet on the unit and to the water in let e g water tap m Open water inlet English Operating Instructions HD 10 25 S VEX Suctioning water
10. nation of the symbols High pressure pencil jet 0 for particularly stubborn accumu lation of grime High pressure fan jet 25 for dirt accumulation over a large surface Low pressure fan jet CHEM lt I FE for operation with detergent or for cleaning at low pressure se ag Operating Instructions HD 10 25 S VEX English Operating with detergent Caution N Unsuitable detergents can harm the cleaner and the object which is to be cleaned Use only detergents which are released by K rcher Proportions of detergent to be used and accompanying instructions should be not ed carefully Use detergents sparingly out of consideration for the environment Karcher cleaning agents guarantee trouble free operation Please seek advice or ask for our catalogue of information sheets on clean ing agents m Fill detergent reservoir m Set nozzle to p m Set the detergent metering valve to the desired concentration Concentration of detergent when flow at maximun Position of metering 1 3 5 7 valve 0 5 2 5 5 0 7 0 Recommended cleaning methods m Spray detergent with low pressure jet spar ingly over the dry surface to be cleaned and let it take effect but not dry out m Spray off rinse off the loosened dirt using the high pressure spray m When you have finished the operation set detergent metering valve to 0 and switch the unit on fo
11. nit total of vibration ISO 5349 Handheld gun m s 2 2 Spray lance m s 2 0 Dimensions Length mm 560 Width mm 500 Height mm 1090 Weight without accessories kg 62 Reservoir capacity detergent 6 Oil quantity pump 1 2 Oil type pump SAE 90 12 HD 10 25 S VEX 4 775 466 0 4 775 470 0 7 343 008 0 6 390 026 0 4 760 550 0 o 2 880 296 0 6 390 026 0 2 880 296 0 6 362 532 0 6 362 524 0 PAT SIE gt Qo 4 037 413 0 Z a 4 775 466 0 4 760 550 0 x 6 390 026 0 o Q 4 580 608 0 6 388 194 0 fr r 6 388 216 0 g o 5 731 609 0 2 880 296 0 4 760 550 0 5 667 061 0 7 303 110 0 5 251 049 0 _ gt P a 7 303 110 0 4 767 067 0 5 251 048 0 7 343 008 0 5 392 038 0 Deo 7 312 060 0 7 303 110 0 5 064 107 0 6 414 681 0 5 032 406 0 5 032 413 0 lt ES DER 4 515 092 0 5 363 613 0 amp 4 515 092 0 y 6 362 161 0 gt D 5 443 291 0 et VS EE 5 310 076 0 7 303 110 0 r lt X gt p eq E 7 343 008 0 5 032 463 0 7 303 110 0 5 392 038 0 5 013 091 0 D 5 057 062 0 08 03 5 961 066 0
12. r about 1 minute and rinse it clear of detergent Interrupting the operation m Release lever of the handgun the unit switches off Retract lever again and the unit switches on again Availability time Within the availability time the unit starts when the hand held spray gun is opened The indicator light will go green If the spray gun remains closed for 30 minutes the availability time ends The indicator light will flash green Reset availability time m Switch off the unit switch m Wait a moment m Switch the unit back on again Customer Service can change the unit to permanent operation Switching the unit off m Set unit switch to 0 and pull out power plug m Close water inlet m Retract lever until the unit is without pres sure m Push safety catch of the hand held spray gun forward to lock the lever of the gun from being actuated inadvertently Danger Risk of scalding due to hot water Re sidual water contained in the switched off unit can heat up When removing the hose from the water inlet the heater water can spurt out and cause scalds Do not remove the hose until the unit has cooled down Transporting the cleaner m To transport the cleaner over relatively long stretches take hold of it by the handle and pull it along behind you m Empty the detergent reservoir before trans porting it horizontally English Operating Instructions HD 10 25 S VEX Storing the cleaner m Place th
Download Pdf Manuals
Related Search