JVC DLA-G10E User's Manual
Contents
1. These specifications are subject to change without notice NAMES OF PARTS Tilt adjustment screw Tilt adjustment screw Ceiling mount The same screws are also used on the opposite side The same screws are also used on the opposite side Vertical angle adjustment screws L plate Horizontal angle adjustment bolts Use the hex wrench provided INSTALLATION Special techniques are necessary for safe installation The customer should never perform the installation work Consult your dealer concerning installation Projection Distance and Screen Size This projector uses a 1 5X zoom lens therefore the maximum projected image size is 1 5 times larger than the minimum projected image size Focus is possible at projection distances of from 2 5m to 20m Use the distances shown below for reference Screen size type Distance from the front screw min Max zoom of the ceiling mount to the screen L m 44 619 170 253 9 3415 5098 If the edges of images are distorted when projecting at the minimum project distance it is recommended that the projector be moved slightly backward Install the projector in a stable location away from walls and furniture for safety during light source lamp and filter replacement LU LL 7 f Wy Wy yy WC LL Yff7f k A Soa 350mm Example 317 52. Horizontal pan range Fixture Mass Fixture size Mass with projector mounted External dimensions with projector mounted Ceiling mount Model Ceiling mounting the DLA G10U E projector Applicable projector 15 degrees 5 degrees 7 degrees 6 2kg 454mm W x 359mm D x 176mm H 20 5kg 454mm W x 402mm D x 377 5mm H Accessories EF G10CG DLA G10U E only M8 x 15 screw 1 flat washer 1 Spring washer 1 M5 x 8 hex bolt 1 flat washer 1 Spring washer 1 Drop prevention fixture 2 Hex wrench 1 Instruction manual 1 Service network 1 The specifications and appearance of this product are subject to change without notice
3. MOUNTING THE PROJECTOR ON THE CEILING MOUNT 1 Engage the L plate on the pin of the ceiling mount Drop prevention fixture 2 Fasten temporarily with the vertical angle adjustment screws 4 which were removed After fastening with the vertical adjustment angle screws 4 perform the adjustments described on page 13 Vertical angle adjustment screw M5 X 15 screws 4 Prepare the following tool Y N Screwdriver Accessories to remove from the projector M5 X 15 screws PROJECTION ANGLE ADJUSTMENTS Pre adjustment Operations Look at the projector instruction manual and turn on the power Use the zoom lens to match the projected image size to the size of the screen Perform the above operations before starting the projection angle adjustments Horizontal angle adjustment top view Use the accessory hex wrench to loosen 6 bolts Move the projector left and right to center the projected image horizontally on the screen When the angle has been correctly adjusted fasten the projector securely by tightening the bolts Vertical angle adjustment side view 4 Center the projected image on the screen vertically and then fasten the projector securely by tightening the bolts Use the tilt adjustment screws 4 locations 2 in fron
4. bolts for M10 X 4 procure separately ceiling installation are to be procured separately Consult your dealer Consult your dealer concerning installation This company assumes absolutely no responsibility if the projector drops due to insufficient installation strength Temporarily fasten with four M10 bolts in the sequence of and position accurately and then securely tighten the four M10 bolts The total weight of the projector and ceiling mount is 20 5kg Install at a sufficient distance referring to the projection distance range table on page 6 Typical Installation In case of a wood ceiling In the case of a concrete ceiling Ceiling Mounting plate 7 Yj Yj pb Use materials that _ r 7 a MI9 beam will withstand the p T p Vi weight of the a JF TK Ne projector and the ceiling mount hao od Q fe 2 g J L j Mounting bolt M10 To ceiling mount Mounting bolt M10 To ceiling mount Drill holes of the above size in the ceiling and Drill holes of the above size in the ceiling and mounting plate then drive in the anchor M10 Drill holes in the beam 2 Securely fasten the ceiling mount with a Q Insert the mounting bolts M10 through the mounting bolt M10 Use anchors that will holes and fasten the ceiling mount Make sure support the weight of the projector and ceiling the weight is supported by the beam Reinforce mount the beam if its strength is insufficient
5. 15mm Completion drawing HOW TO INSTALL CAUTION Do not connect the power plug to a power outlet until all preparations have been completed 1 Extend the two legs of the DLA G10U E by rotating Rotate until rotation becomes stiff and then stop to prevent damage The other legs of Prepare the following tool the projector do not rotate Peel off the rubber pad adhered to one of the legs so the embedded nut is visible Screwdriver Rubber pad 2 Remove the 4 adjustment screws and remove the ceiling mount Remove the 2 screws from the ceiling mount and open the mount 90 degrees Remove 2 screws and then detach the stopper from the front of the mount Ceiling mount Stopper Use care to prevent the top fitting from dropping during the installation work since this could result in injury or damage HOW TO INSTALL 3 Install the ceiling mount on the DLA G10U E by aligning the holes and cutouts then install the stopper es Top fitting N CAUTION Use care to prevent the top fitting from dropping during the installation work since this could result in injury or damage Prepare the following accessories Spring washer 1 Screw M8 X 15mm M8 X 15mm 1 _ Flat washer 1 Spring washer Flat washer Completion drawing HOW TO PREVENT DROPPING 1 Remove the U fitting mounting screws Procure a drop prevention chain or wire of su
6. JVC MM D ILA Projector DLA G10U E Ceiling Mount Projecteur D ILA Monture au plafond pour DLA G10U E CONTENTS Safety Precautions Unit Dimensions Names of Parts Installation Parts List How to Install How to Prevent Dropping Installing the Ceiling Mount on the Ceiling Mounting the Projector on the Ceiling Mount Projection Angle Adjustments Replacing the Lamp and Filter Specifications Consignes de s curit Dimensions de l appareil Nom des pi ces Installation Liste des pi ces Comment installer Pour emp cher la chute Installation de la monture au plafond sur le plafond Montage du projecteur sur la monture au plafond R glage de l angle de projection Remplacement de la lampe et du filtre Fiche technique When installing also read the DLA G10U E instruction manual Thank you for purchasing this product Before using your new purchase please read this instruction manual thoroughly And after reading be sure to store this instruction manual in a safe place for future reference Pour l installation se reporter galement au mode d emploi du DLA G10U E Nous vous remercions d avoir achet ce produit Avant d utiliser votre projecteur veuillez lire attentivement toutes les instructions de ce manuel Puis apres l avoir lu rangez le en lieu sur de fa on a pouvoir vous y reporter Instruction Manual Mode d oemploi PRECAUTIONS FOR SAFE AND PROPER USE Regarding Symbol Indicat
7. fficient strength If a chain is attached M5 X 8 bolt Spring washer T amp To ceilin Flat washer 27 3 7____ Drop prevention fixture M5 X 8 bolt 1 Hex wrench Spring washer 1 Go Flat washer 1 Drop prevention fixture 1 4 Attach the drop prevention fixture to the ceiling using the same procedure as described in items 1 3 Typical Installation In case of a wood ceiling In the case of a concrete ceiling ili or M5 Ceiling Say Mounting plate 7 PS Use materials that L 7 will withstand the 1 Beam weight of the TT LT Ne projector and the ceiling mount Se 0 Mounting bolt M5 To ceiling mount Mounting bolt M5 To ceiling mount H a ita through the mounting plate beam The M5 bolts for Drill a hole in the ceiling and then drive in the and ceiling J hor M5 ceiling mounting anchor M5 ee Be ar Sie el aac hole are to be procured Securely fasten the drop prevention fixture PP separately Consult with mounting bolts M5 your dealer CAUTION Be sure to mount the drop prevention fixture directly above the projector Consult your dealer concerning the ceiling installation work INSTALLING THE CEILING MOUNT ON THE CEILING Install the ceiling mount on the ceiling To ensure safety special techniques are required for installation Do not attempt to perform the installation work yourself Mounting bolt The M10
8. ge When the prevent malfunction or deterioration of the installation work is difficult lower to a safe product height and call a professional installer Do not install where there is danger of contact with excessive dust oil smoke tobacco smoke water vapor etc These will adhere to the lens liquid crystal panel mirror etc and result in blurred or dark images Never suspend or hang objects from the S ceiling mount An excessive load can cause the ceiling mount to fall and result in injury or damage This product is to be used only for ceiling mounting Do not use it for any other application And never make alterations because this can cause an accident Do not mount any projector other than the DLA G10U E on this product This could result in an accident Install in a room that can be darkened to prevent direct sunlight illumination or reflected light on the screen Such light will cause the images to appear whitish and be hard to view Use curtains in rooms where light enters from the outside a D wy Do not install where there is danger of vibration or impact This could cause the ceiling mount to drop and result in injury or damage U N IT DI M NS l O NS All dimensions below are given in mm 3 11 Elongated holes O11 454 402 436 396 318 5 377 5
9. ions Numerous symbols are employed as indication in the precautions for safety precautions for handling and in the indication to the products These are designed to prevent in advance any possible infliction of injury on you and other individuals and the damage of properties through the proper use of the product The symbols and meanings are shown below Grasp the contents of the symbols completely before reading this manual This represents the contents in which the probabilities for death or serious injury are assumed if this symbol indication is ignored and the product is erroneously handled This represents the contents in which the probabilities for injury to be inflicted are assumed and the contents in which material damages to be sustained are assumed if this symbol indication is ignored and the product is erroneously handled Examples of Symbol Indications This symbol informs you of the presence of the contents that demands caution including danger and warning Specifically prohibited contents caution against electric shock in case of the left symbol are illustrated in the symbol This symbol informs you of prohibited actions Specifically prohibited contents prohibition of disassembly in case of the left symbol are illustrated in the symbol and its vicinity This symbol informs you of the contents that forces you to take some action or gives you some guidelines or instructions Specific contents of instructions unplug the
10. mm ce Wall furniture etc 300mm The center lines of the Z Wall furniture ete j projector lens and the ceiling a 2227 mount are not aligned omn a Screen L it 172mm 200mm j Wall furniture etc N CAUTION Do not install in locations such as those shown below since this could result in malfunction or fire S Box or other closed space where ventilation is not possible Places where there is oil smoke water vapor or tobacco smoke Humid or dusty places Places where the temperature is low or high and the humidity is outside the permissible operating range Permissible temperature range 5 35 degrees C Permissible humidity range 20 80 no condensation Direct sunlight and indoor lighting can cause the screen to appear whitish and difficult to view Use curtains to shut out light when necessary Install the projector as level as possible otherwise malfunction may occur PARTS LIST The following parts are provided as accessories with this projector Make sure all of the parts are present before stating the installation work 1 Ceiling mount 1 2 Drop prevention fixture 2 3 Hex wrench 1 1 4 Hex bolt 5 Flat washer 6 Spring washer int M5 X 8mm 8 Flat washer 1 9 Spring washer 1 B M8 X
11. power cord from the outlet in case of the left symbol are illustrated WARNING CAUTION To assure safety special techniques are ia Do not install in locations subject to low or high S required for installation The customer should S temperatures near a kitchen table or never perform this work Consult your dealer humidifier or where there is oil smoke or water concerning installation vapor This can result in projector malfunction deterioration of image quality fire or electrical shock Provide sufficient reinforcement when the Do not install the projector in a box or other S ceiling on which this product will be installed is closed space where the hot air from the too weak Install so as to prevent any safety projector cannot be exhausted Do not block related problems If the ceiling is too weak or the exhaust port of the projector Projector the installation is improperly performed this overheating can result in malfunction loss of product could possibly drop and cause injury image quality or electrical shock or damage Permissible temperature range 5 35 degrees C Permissible humidity range A CAUTI O N Ke 20 80 no condensation E When replacing he lamp or fier provi a HANDLING PRECAUTIONS solid footing from which a comfortable posture can be adopted Working with an unstable footing or in an uncomfortable posture can Please observe the following cautions to result in injury or dama
12. t and 2 at the rear to adjust the projector so that the projected image is not tilted in relation to the screen then securely tighten the screws Repeat the above adjustments if the projected image is still unsatisfactory REPLACING THE LAMP AND FILTER Observe the following cautions when replacing the light source lamp or filter Failure to do so can result in personal injury or projector damage Turn off the POWER button of the remote control or OPERATE button of the projector and disconnect the power cord from the power outlet A CAUTION Take precautions to keep the DLG G10U E main unit and lens away from furniture lamps etc Prepare a stable place to stand where you can work comfortably When the installation work is difficult lower to a safe height and call a professional installer 1 To replace the lamp and filter remove 2 screws while supporting the DLA G10U E with the hands and then lower it gently i When removing the screws always insert the accessory hex wrench to prevent the projector dropping suddenly 2 Replace the lamp and filter Replace in accordance with the instructions given in the DLA G10U E instruction manual Filter OQOQ0000000000 UOQO0D00000000 OQQDQ000000000 OQOOQ000000000 OQOO0000000000 UOQOQ000000000 SPECIFICATIONS Part name Application Vertical tilt range Horizontal tilt range
Download Pdf Manuals
Related Search