Jasco 45245 User's Manual
Contents
1. areas where half of the area is in bright sunlight and the other half is dark such as the shadow of a building All types of cameras have difficulty seeing into areas of such divergent light levels e In low light conditions the camera will automatically activate its high powered Infrared IR LED s and switch the camera to Long Range Night Vision mode Long Range Night Vision viewing distance can be up to 60ft and will be viewed in B W e The included AC adapter must be positioned no farther than 8 from an AC outlet Do not use the supplied adapter outside If you need to extend the AC adapter cable 12 ft extensions are available by contacting Technical Support at 800 654 8483 6 e The Camera has an unobstructed wireless transmission range up to 200 ft from the receiver Transmission distance indoors is reduced due to interior walls wiring household fixtures and metal plumbing LONG RANGE NIGHT VISION The 45245 Wireless Color Camera features Long Range Night Vision tech nology Objects and images can be seen in little or no light up to 60 ft The camera A uses a special image sensor that automatically detects available light levels It turns on off the high powered Infrared IR LEDs on the front of the camera These LEDs provide artificial light that allows the camera to see in the dark Night Vision will appear as a Black and White image When the image sensor detects enough light color will return to the2. check and identify all the parts before proceeding with the installation 1 Wireless Add on Color Camera 2 Wall mounting hardware 3 screws 5 plastic anchors 5 AC adapter 4 Adjustment wrench CHOOSING A CAMERA MOUNTING LOCATION The Wireless Add on Color Camera is desiged to be mounted to a wall It is suitable for indoor or outdoor use When choosing a mounting location please be advised e The wireless camera must be used with a GE Wireless Home Monitoring system The location of the GE Wireless Receiver or monitor may affect where you mount the camera e This camera is designed to be reliable for outdoor use however its flexible design allows it to be used indoors as well It is expecially suited for viewing large areas in low or no light e f using outdoors take time to first consider how you will route the cable back the power adapter The mounting bracket routes the cable through the bracket providing a vandal resistant design There is a slot located at the base of the mounting plate so that the cable can exit the cable ran on the outdoor surface The cable can also be routed out the bracket and along a wall and or ceiling keeping it hidden protected e The universal multi axis bracket allows you to mount at almost any angle e DO NOT position the camera so that it points directly into the sun or any bright light as this may cause damage to the camera e Avoid positioning the camera so that it is viewing
3. Indoor Outdoor 45245 Home Monitoring Wireless Add on Color Camera User Manual For indoor outdoor use www jascoproducts com 1 800 654 8483 2 Table of Contents Product Features eese 3 eje sede Qu IQ Seen 4 Choosing A Camera Mounting Location 4 Long Range Night Vision see 6 Mu lti Camerg SYSTEMS ossia on tenenti editus 6 Camera Channel Selection sssr 7 ASS Mennen 8 TEODUDISSIDOHDU etende 12 SC CIM CO WONS asana hist 19 LO s M M 16 FCC Statement tud oret ASS 17 Thank you for purchasing the GE Wireless Add on Color Camera This product is intended for use as an add on camera for the GE Home Monitoring Surveillance Systems Please review these instructions carefully before attempting to operate the camera PRODUCT FEATURES e Weather resistant metal camera casing designed for outdoor use e Black anodized finish prevents rust and unwanted reflections e Long Range Night Vision high powered LED s allow you to see up to 60ft in the dark e Vandal resistant bracket hides cables e Adjustable sun shield to minimize glare e Multi axis adjustment bracket allows you to mount the camera at almost any angle e Adjustable antenna e WiFi friendly won t interfere with home wireless networks Wirelessly transmits audio and video up to 200 ft unobstructed line of sight e UL approved power cable 4 PACKAGE CONTENTS Please
4. ceiver or both to improve the reception quality 5 If a camera is positioned close to the monitor point antenna away from the receiver 4 Reposition other nearby equipment transmitting on the 900MHz frequency 5 Adjust the antenna for the camera monitor or both to obtain best image 14 mmm Audio problems 1 Ensure the volume is turned up sufficiently on the Monitor lor TV 2 Make sure the sound is within the microphone range 3 If the unit emits a loud wailing sound feeds back try moving the camera away from the receiver or angle the receiver differently 15 SPECIFICATIONS Subject to change without notice CAMERA HUtcia pem nee eee no ee E es er Pee eT NTSC Integrated Lens 6 0mm F1 5 fixed focus TN 510x496 TV Lines Image Sensor ennen erneer 1 3 CMOS Min Illumination 0 5lux up to 60 ft VOI NEN a e ret eT ge re E CTT 9VDC Current CONSUMPTION ananas ennen 550mA maximum Overall SIZE nennen 2 5 W x2 25Hx6 75D Frequency KONE neee 902 928 MHz Patenten hetis FM channel Sal OC LOT seams dni Rc atqtie Manual Case FINIS N anpenpan Aluminum Operating Temperature 14 F to 104 F 20 C to 55 C Pagi I NR ET Less than 8596 16 ONE YEAR LIMITED WARRANTY Jasco Products Company warrants this product to be free from manufacturing defects for a period of one year from the original date of consumer purchase This warranty is limited to the repair or replacement of t
5. drilling into brick drill holes and insert anchors into drilled holes for snug fit Align holes in mounting bracket to drilled holes insert screws and screw in until plate has secure fit Do not over tighten screws Figure C Mounting bracket using plastic anchors Plastic anchors BO DTT auuJJo EO MUTET OV TIG Vr Or a auuQ c Using included adjustment wrench slightly loosen the hex head bracket nuts on camera bracket to position camera s multi axis bracket so camera is pointed toward desired viewing area Tighten bracket nuts Do not over tighten nuts 11 d Take care to position the camera in the correct orientation To ensure the camera image is not QISA positioned upside down you may have to rotate the camera housing so the channel slelection switch is positioned above the lens and the light sensor is below the lens Step 4 Antenna Adjustment Once mounted adjust the camera s antenna to achieve best reception Note if ceiling mounted you may not be able to position the antenna completely vertical pointed up It is acceptable to position the antenna vertically but pointed down This typically will not cause any interference or reduce the reception ability of the camera Do not force the antenna beyond physical stops Off Q Ji SS K i Proper a Antenna Rotation Uu Wall B Mount 5 Ceiling Mount Channel Selection 12 Step 5 AC P
6. e the camera s mounting bracket as a template to mark holes for drilling Mark three holes on the wall for the anchors or screws as shown Please take care to mark the center of the holes Note Before mounting camera permanently check to ensure the appropriate channel has been selected see Channel Selection to provide good reception at the receiver monitor Step 2 Cable routing IMPORTANT a If running the cable along the wall surface position cable through slot at base of mounting bracket before installing mounting bracket see figure A Figure A Running cable on surface of wall Pilot holes for mounting screws ED d rt TT auuJ b If the cable needs to be ran through a wall or ceiling then an additional hole will need to be drilled using the 3 8 drill bit Drill the hole in the center of the three mounting screw holes see figure B Fit connector and cable through hole before securing the mounting bracket Figure B Plasti meme m pees cam exo anchors ERRO CEERD lemn E ES OND lt 10 Step 3 Mounting bracket a If mounting to a stud wood surface or other non brick material use the 1 8 drill bit to drill pilot holes drill holes Align holes in mounting bracket to drilled holes insert screws and screw in until plate has secure fit Do not over tighten screws b If mounting to drywall or brick material use plastic anchors see Figure C Using 3 16 drill bit masonry bit if
7. his product only and does not extend to consequential or incidental damage to other products that may be used with this unit This warranty is in lieu of all other warranties express or implied Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damages so the above limitations may not apply to you This warranty gives you specific rights and you may also have other rights which vary from state to state If unit should prove defective within the warranty period return prepaid with dated proof of purchase to Jasco Products Company 10 E Memorial Road Oklahoma City OK 73114 17 FCC STATEMENT This device complies with part 15 of the FCC rules Operation is subject to the following two conditions e The supplied adapter is for indoor use only 1 This device may not cause harmful Do not run the camera cable inside walls when securing the interference Peer unir 2 This device must accept any interference received including interference that may cause undesired operation FCC NOTE The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These
8. images 20 Infrared IR LEDs MULTI CAMERA SYSTEMS The Wireless Add on Color Camera is designed as an add on camera to work only with a variety of GE Wireless Camera Systems 45234 45236 45239 45246 Each system can accept a maximum of two cameras CAMERA CHANNEL SELECTION Each wireless camera must be assigned to a specific channel 1 or 2 through the use of a slide switch located on the inside of the camera housing First slide off the sun shield and then unscrew the lens from the camera The receiver or monitor must have its channel selection set to the same corresponding number Channel Selection switch In a two camera system one camera is set to Channel 1 and the other is set to Channel 2 The receiver or monitor must be set to the 2 camera position in order to view both cameras alternately see receiver or monitor manuals for specific channel selection requirements 8 INSTALLATION Wall Mount or Ceiling Mount you will need Drill 3 8 Drill bit if running cable thru wall or ceiling 1 8 drill bit for drilling screw pilot holes if mounting into wood or non brick material 3 16 drill Bit for drilling holes for plastic anchor s if mounting onto drywall or brick material a screwdriver Adjustment wrench included Step 1 Mounting preparation Once a suitable location for the camera has been selected and the cable route has been determined you will need to us
9. limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Only use the supplied cUL listed AC to DC adapter 18 Notes Notes 19 is a trademark of General Electric Company and is used under license to Jasco Products Company LLC 10 E Memorial Road Oklahoma City OK 73114 www jascoproducts com 45245 rev 5 18 10
10. ower Locate the power cable end connection Attach the AC adapter labeled camera to end of cable coming from the camera Plug in AC adapter to nearest AC outlet Adapter must be used in a dry location AC power extension cables are available from the Call Center 1 800 654 8483 or visit online at Www jascoproducts com TROUBLE SHOOTING If you are having trouble operating this product please consult the guide below If you have any questions or feel the camera system is not operating correctly or you simply need additional information please visit our web site www jascoproducts com or contact our Technical Support Group 1 800 654 8483 option 4 No camera picture 1 Check all connectors Make sure camerats and receiver are powered ON 2 Ensure camera s and receiver are set to correct channel s 3 Make sure camera is within range of receiver 4 Adjust the antenna for the camera monitor or both to obtain best image 13 Ee ELELL ICOEICIIZIIIL ILI L I OLLLLIL JLOILICUG LCLLIL1 ce Blank monitor 1 Make sure receiver or monitor is switched ON and the correct video input has been selected 2 Ensure AC adapters are completely plugged into the socket and the camera and or receiver s power indication light is on Interference on camera picture 1 Make sure each camera transmitter is within range and that no large obstructions are blocking the signal 2 Try repositioning the camera monitor re
Download Pdf Manuals
Related Search