Ives 611 Series User's Manual
Contents
1. Installation Instructions MN Hh 829172 00 611 and 711 Series Swing Clear Continuous Hinges A CAUTION Please follow the installation instructions carefully Not doing so may result in improper installation and void the manufacturer s guarantee INSTALLATION NOTES Reinforcing and Rivet Nuts No reinforcing is necessary except on heavy doors Reinforcement and rivet nuts are required in the frame and door when door weight exceeds 300 pounds Maximum door weight is 600 pounds Pairs of Doors with Mullions If the mullion is between the doors treat as a single door installation If the mullion is behind the doors treat as a double door installation Note Before proceeding check to be sure that hinge is proper size Height of hinge should be 7 8 LESS than opening height See other side of page for cutting instructions Mark frame hole locations A Determine TOP of hinge using To bottom of frame door and frame as guide B Open hinge and place frame leaf flat against surface of frame leaving 1 8 gap between top of hinge and bottom of frame header and edge of hinge frame leaf flush with inside edge of frame C Mark hole locations on frame using center punch A center punch mark is required to start self drilling screws accurately DO NOT install hinge to frame at this time 2 Mount hinge to door A Place door leaf of hinge against hinge edge of door so that top of hinge is F2. save tip for step 5 B Expose 1 of hinge pin Measure and mark 3 4 from end of pin DOUBLE CHECK MEASUREMENT BEFORE CUTTING C Cut pin at mark O Insert top and bottom tip A Tap hinge pin back into barrel B Tap hinge pin tips retained from step 3 and 4 firmly into top and bottom of barrel until shoulder sets squarely on barrel NOTE Both tips MUST BE INSTALLED to hold hinge pin in position Important Note If more than 6 is cut from bottom of hinge additional mounting holes will be required on bottom of hinge Use cut off piece of hinge to mark and prepare hole locations on bottom of hinge 829172 00 0
3. lush with flush with top of door and edge guard top of door is flush with inside face of door S i a aa aa B With hinge held firmly in place use 2 o 10 x 1 2 self drilling screws to fasten Door leaf to metal door or 10 x 1 wood o screws to fasten leaf to wood door Flush Note Fasten top screw first and S bottom most screw second making Lee ee Ne sure hinge is aligned correctly A Ea ALL HOLE LOCATIONS ON HINGE LEAF MUST BE FASTENED TO DOOR FOR PROPER OPERATION FAILURE TO INSTALL ALL FASTENERS WILL VOID WARRANTY AND UL FIRE LABEL LISTINGS Mount door to frame A Move door into opening and align mounting holes in frame leaf of hinge with marks on frame made in step 1 above Note An angle block jack or Door shims will be helpful in positioning the door properly B With hinge and door held firmly and accurately in place use 10 x 1 2 self drilling screws to fasten frame leaf of hinge to frame in marked locations al o ALL HOLE LOCATIONS ON HINGE LEAF MUST BE FASTENED TO FRAME FOR PROPER OPERATION FAILURE TO INSTALL ALL FASTENERS WILL VOID WARRANTY AND UL FIRE LABEL LISTINGS Check for proper operation A Close door and check for proper operation and y clearances There should be 1 8 clearance between the A top of the door and the bottom of the frame header and 5 32 1 8 clea
4. rance between the frame and edge of the door when the door is closed Adjustments can be made by shimming frame or door leaf of hinge EE 5 32 LEX Ingersoll Rand 829172 00 0 2006 Ingersoll Rand Company Limited Security Technologies Instructions for Cutting Hinge 1 Determine hinge height A Measure height of opening from finished floor to underside of door frame header B Hinge height is height of opening MINUS 7 8 Height of opening MINUS 7 8 a 2 Mark hinge for cutting A Determine which end of Top hinge will be the TOP using door and frame as a guide B Open hinge to expose Opening back of hinge holes height are NOT countersunk minus 7 8 C Measure hinge height calculated in step 1 from top of hinge D Using square mark a line on back of both hinge Bottom leaves and the barrel DOUBLE CHECK MEASUREMENT BEFORE CUTTING NOTE Cut end of hinge must be used as BOTTOM OF HINGE ONLY Cut hinge A Fold hinge so that cut line is visible B Starting on barrel cut through A entire hinge along line C Debur all cut edges with file D Use center punch or heavy gauge 4 nail on pin in short cut off portion of hinge to remove hinge tip SAVE HINGE TIP for use in step 5 Page 2 of 2 O Shorten hinge pin 3 4 A Using center punch or heavy nail tap on cut surface of hinge pin to remove top hinge tip
Download Pdf Manuals
Related Search