Inland Products 10630 User's Manual
Contents
1. 10885 8 Flat Lap Conversion Kit Convert any SwapTop Table Saw into a flat lap machine for shaping and polishing Includes 4 graduated grit diamond laps master lap polishing pad and compound 10655 Grinder Shaper Conversion Kit Converts any SwapTop Table Saw into a diamond grinder shaper Service For questions or comments regarding the use of this or any Inland product visit our website at www inlandcraft com email us at helpdesk inlandcraft com call Inland Customer Service at 1 800 521 8428 from 9 AM to 5 PM EST or write Inland Craft Products Co 32052 Edward Drive Madison Heights MI 48071 Rev No 5 Stock No 69861060 fainiand SwapTop Table Saws Users Guide Thank you for buying this Inland product These instructions cover assembly and use of the SwapTop Table Saw models 10630 10660 10670 and the SwapTop Table Saw Conversion Kit models 10665 10675 Please read all the instructions to understand the correct components set up and use of your machine Safety y Always wear safety glasses or goggles You can use a FaceShield or MagnaShield for additional protection Plug into a grounded electrical system Do Not override the grounding system V If your motor unit has a speed control feature make sure that you set it at the maximum speed for proper operation Always unplug your machine when switching between set ups installing blades and making adjustments Place on a sturdy level water tol2. Product Specifications Convertible Motor Unit Table Saw Variable Speed Motor Unit Height 6 1 2 Permanent Magnet DC motor rectified for AC outlets Blade Diameter 6 1 2 Max Torque 48 oz in Work Surface 12 x 9 3 4 Max RPM 2800 Maximum Cutting Thickness 1 Shaft OD 312 5 16 Stainless Steel Available in 115V or 230 240V models Two Year Full Confidence Warranty Parts and Accessories 40960 6 12 x 020 Trim Saw Blade Standard A great all around diamond blade for cutting hard materials 40961 6 x 012 Trim Saw Blade ThinCut A little bit thinner diamond blade which will cut a little faster and consume a little less material but will also be a little less durable 40968 6 1 2 x 008 Trim Saw Blade Extra ThinCut Our thinnest diamond blade for use on the most precious materials when you need to minimize the waste involved in cutting 90960 MetalCut 6 1 2 Trim Saw Blade Toothed blade for use when cutting soft nonferrous metals such as copper brass or silver and some plastics 24 TPI teeth per inch 90964 WoodCut 6 1 2 Trim Saw Blade Toothed blade for use when cutting wood and some plastics 10 TPI teeth per inch 69801661 Rip Fence Kit Use to saw uniform width strips and pieces 10685 6 Flat Lap Conversion Kit Convert any SwapTop Table Saw into a flat lap machine for shaping and polishing Includes 4 graduated grit diamond laps master lap polishing pad and compound
3. ade to do the cutting Too much pressure will slow the cutting process 3 If you feel the blade binding make sure you are feeding material slowly and straight into the blade Using the protractor or optional rip fence Inland no 69801661 to help guide material may help alleviate this 3 NEVER cut anything thicker than the blade height above the work surface Wet Sawing 1 One of the most versatile features of your saw is it can operate wet using diamond blades 2 If you have been dry sawing you will need to remove any sawing debris from the surface and sawing well Install a 6 12 Trim Saw diamond blade following the instructions in Setting Up the Swap Top Table Saw 3 Set up the Water Drip AddOn Kit per its instructions and connect the coolant feed hose to the top of the blade guard Make sure the coolant flow adjustment valve is closed then fill the reservoir with coolant 4 Connect the plastic drain hose to the overflow outlet on the bottom rear of the saw base Place the end in an appropriate receptacle 5 Open the valve on the coolant reservoir to start the coolant flowing onto the blade The coolant keeps the working area of the blade clear of debris with a small puddle of coolant showing while sawing There should not be water flooding the saw table If a paste forms around the cutting area increase the coolant flow sawing dry will severely affect the life and performance of diamond blades 6 Practice with a scrap pi
4. ece of material and start slowly to get a feel for cutting with a diamond blade You will soon develop a feel for the speed that does not slow the motor while giving you a good sawing rate Maintenance Always unplug the unit when cleaning We recommend after wet use to drain any remaining coolant The debris from many materials has a tendency to harden Rinse and dry the reservoir and removable work surface After dry use empty or vacuum the reservoir of debris and then wipe down and dry the reservoir and removable work surface Never allow the yellow motor unit to get wet or immerse it in water Use a vacuum to remove any debris from the bottom air vents on the unit Always secure blades to the flat side of the motor shaft You can use a thin coating of Inland MotorShaft Lubricant Inland no 50028 or petroleum jelly to help keep the arbor from seizing on the shaft Check the power cord periodically for cuts or damage Check all coolant lines and tubes to see that they are not clogged
5. ep Set the motor unit with blade mounted loosely into the machine base Press down on the motor unit slowly yet firmly until you feel it seat in the base It will locate snugly Slide the arbor to the center of the saw blade well Tighten the blade arbor set screw to the flat portion of the motor shaft using the 5 64 allen wrench provided Lower the work surface straight down onto the base making sure the U shaped extensions in the top slide inside the blade well Make sure the spring loaded latches on each side snap into place You should be able to lift the entire machine by the work surface without it disengaging Verify that the motor unit is unplugged Turn the blade by hand to make sure it does not rub against the sides of the metal work surface If necessary reposition the blade arbor so that the blade will spin freely Set the blade guard in position in the slot provided on the work surface behind the blade Check the blade to make sure there is no interference be tween the blade guard and the work surface by plugging in the saw and turning the switch on and off quickly The saw should run smoothly and quietly If the blade makes contact with anything repeat Steps 4 6 until it turns properly saw blade unthreaded s side toward Sawing With Your SwapTop Dry Sawing Turn on the saw 2 Place your material flat on the table Slowly feed it into the blade Allow the bl
6. erant surface at a comfortable working height V Never operate with guard covers and safety features removed or disabled Parts List Name Qty 10630 10660 10665 10670 10675 A Machine Base 1 yes yes no yes no B Motor Unit 1 yes yes no yes no C Removable Work Surface 1 yes yes yes yes yes D Blade Arbor amp Nut 1 yes yes yes yes yes E Blade Arbor Wrench 1 yes yes yes yes yes F Protractor 1 yes yes yes yes yes G Blade Guard 1 yes yes yes yes yes 5 64 Allen Wrench 2 yes yes yes yes yes J Plastic Drain Tube 1 yes yes yes yes yes 1 6 Saw Blade WoodCut MetalCut MetalCut Diamond Diamond Setting Up the SwapTop Table Saw Make sure the machine is unplugged If you were set F up as a grinder or flat lap remove all diamond tools work surfaces and reservoirs You should have only the open machine base and yellow motor unit Mount the saw blade on the blade arbor with the blade teeth positioned to saw downward If you are using a diamond blade this is not applicable Secure the blade using the blade arbor nut with the unthreaded side toward the blade and tighten using the provided wrench The threads are reverse threads so the nut tightens by turning it to the left counterclockwise Slide the arbor with mounted blade onto the motor shaft Position the blade and arbor so the blade will rest approximately in the center of the saw blade well Don t tighten yet exact positioning will be done in the next st
Download Pdf Manuals
Related Search