InFocus SP-CEIL-010 User's Manual
Contents
1. Use the Allen wrench F to remove the upper plate from the mount assembly D 7 Use the Allen wrench to remove the two screws from the enclosed end of the of the suspension adapter and place it into the slotted extension on the upper plate E Make sure that the two 2 outer holes on the suspension adapter align with the holes on the slotted extension on the upper plate 8 Replace the two screws removed in step 2 into the two 2 holes to secure the suspension adapter to the upper plate 9 Attach the mount assembly to the suspension adapter and secure them with the two screws removed in step 1 10 Secure the upper assembly to the ceiling using the commercially available hardware E suitable for your environment Be sure that the upper assembly arrow is pointing toward your screen 11 Carefully raise the projector C with the mounting bracket B attached and insert it into the bottom of the upper assembly D by its tabs 12 Rotate the projector C with the mounting bracket B attached 180 so that the projector s focus ring is pointing toward your screen 13 Align the safety knob on the mount assembly with the end of the arrow shaped slot on the mounting bracket B and screw it through the opening to prevent further rotation Hand tighten the safety knob remaining two tension knobs to secure the mounting bracket to the amount SEE FIGURE 3 CAUTION Check all of the hardware for proper tightness and security Do not over tighten2. installation environment If you are unsure about the installation environment please consider having it reinforced and having the projector installed by qualified personnel Failure to do so could result in serious personal injury and damage to the projector To avoid personal injury use only an approved projector mount Using an unauthorized projector mount may lead to poor ventilation and projector failure When installing the projector mount keep in mind that the projector s focus ring is not squarely in the center of the front of the projector but offset by several inches Make sure that when you mount the projector you offset the installation to match the amount of inches that the projector s focus ring is offset from the center of the front of the projector UL E176225 Copyright by InFocus Corporation Wilsonville OR All rights reserved Hardware description The Digital Projector Mount utilizes the following hardware Note that the letters associated with the hardware on this list correspond to the letters listed in the instructions for each installation method A Four 4 6 mm x 10 mm Phillips head screws supplied B One 1 mounting bracket supplied C Digital Projector not included D One 1 Litemount Plus assembly supplied NOTE Hardware item E is what secures the Digital Projector Mount to your ceiling wall tabletop floor Make sure you consult with your local hardware store staff for t
3. the screws NOTE Use the Allen wrench key F for the following modification SAI Wood stud Ceiling structure Center of wood stud Adjustable screws ri i I J J Extension adapter e Insert and rotate 180 and lock down Solid ceiling structure WARNING When using the optional extension adapters and making a height adjustment while secured to the wall or ceiling do not remove the screws completely from the extension Failure to do so could result in injury and damage to the projector Insert and rotate 180 and lock down Wall Mount Installation Complete the following steps to install the projector mount and projector to your wall FIGURE 4 e PA A Wall waod stud Note Look at the bottom of the upper assembly D and locate the arrow Make sure you install the projector mount with the arrow pointing toward your screen NOTE Follow step 3 to secure the extension to the mount assembly 15 Secure the upper plate to the wall using the commercially available hardware E suitable for your environment Be sure that the screen indicator arrow is pointing toward your screen 16 Carefully raise the projector C with the mounting bracket B attached and insert it into the bottom of the mount assembly by its tabs 17 Rotate the projector C with the mounting bracket B attached 180 so that the projector s foc
4. InFocus Cc OR PO RATIO N 27700B S W Parkway Ave Wilsonville Oregon 97070 9215 1 800 294 6400 www infocus com SP CEIL 010 DIGITAL PROJECTOR MOUNT Installation Instructions These are the installation instructions for your Digital Projector Mount Included are four methods of installation Select the method that works best for your viewing situation The methods are 3 Fixed Height Ceiling Installation best for short ceilings eight 8 or lower g Adjustable Height Ceiling Installation best for high ceilings nine 9 feet or higher SP LTMT EXTP S height adjustable extension is required Q Wall Mount Installation for installing the Digital Projector Mount on a rear wall the SP LTMT EXTP S height adjustable extension is required NOTE If the required height range is greater than 1274 the optional SP LTMT EXTP could be used to extend the length of the suspension adapter For further information or ordering assistance please contact us at the phone number and address listed at the top of this column A Before You Start the Installation The wall or ceiling where you want to install the digital projector must be capable of supporting a weight that is five 5 times the weight of 7lbs the projector you are installing Consult the projector s documentation for weight specifications If the wall ceiling tabletop shelf or floor is not strong enough to handle five 5 times the weight of 7lbs then you must reinforce the
5. he type of hardware that works best for your installation environment E SINGLE WOOD STUD If mounting on a single wood stud use three 3 14 x 2 Lag bolts minimum commercially available Use the mounting points on the center of the plate as indicated in the assembly diagram SOLID STRUCTURE If mounting to a solid structure use four 4 5 16 x 2 Lag bolts or commercially available hardware depending on the installation requirements Use the mounting points found on the outer points of the mounting plate as indicated in the assembly diagram F Allen wrench supplied Tools Needed for Installing the Digital Projector Mount You need the following tools to install the Digital Projector Mount e Phillips head screwdriver not included e Allen wrench included e Drill for installation environment only do not use a drill on the Digital Projector or the Digital Projector Mount and drill bit to match the hardware for your installation environment not included e The commercially available hardware E that is required by your installation environment not included Lightmount Plus Overview 3 Single wood stud mounting points 4 Solid structure mounting points 2 Cable access points Adjustable extension Safety knobs Red indicator 2 Tension knobs Screen side Yellow indicator Clamp plate Lower assembly Ce
6. iling plate Getting the projector ready Before you start the installation process prepare your Digital Projector by performing the following steps FIGURE 1 1 Turn the projector C upside down and place it on a clean flat surface preferably on a towel 2 Locate the mounting bracket B and align it over the holes on the projector 3 Locate the four 4 6 mm x 10 mm Phillips head screws A 4 Use the Phillips head screwdriver to secure the mounting bracket B to the projector via the three 3 Phillips head screws A Do not over tighten the screws FIGURE 1 a Optional Fixed Height Ceiling Installation Complete the following steps to install the projector mount and projector on your ceiling This installation works best with low ceilings FIGURE 2 Note Look at the bottom of the mount assembly D and locate the arrow Make sure you install the projector mount with the arrow pointing toward your screen 1 Remove the upper plate from the assembly D secure to the ceiling structure using the commercially available hardware E suitable for your environment Be sure that the mount assembly screen indicator arrow is pointing toward your screen 2 _ Replace the mount assembly with the upper plate and fully raise the safety knob and tension knobs all the way Carefully raise the projector C with the mounting bracket B attached and insert it into the bottom of the mount assembly D by its tabs 3 Rotate
7. the projector C with the mounting bracket B attached 180 so that the projector s focus ring is pointing toward your screen 4 Align the safety knob on the mount assembly D with the end of the arrow shaped slot on the mounting bracket B and screw it through the opening to prevent further rotation Hand tighten the safety knob 5 Hand tighten the remaining two tension knobs to secure the mounting bracket B to the mount assembly D CAUTION Check all of the hardware for proper tightness and security Do not over tighten the screws Remove M8 Hex head screws flat washers and star lock washers Remove the center extension from the assembly Remove M8 Hex head screws flat washers and star lock washers Ceiling plate Replace the ceiling plate Bottom assembly Replace M8 Hex head screws flat washers and star lock washers Insert and rotate 180 and lock down Insert and rotate 180 and lock down Adjustable Height Ceiling Installation Complete the following steps to install the projector mount and projector on your ceiling with the optional suspension adapter This installation works best with high ceilings FIGURE 3 Note Look at the bottom of the upper assembly D and locate the arrow Make sure you install the projector mount with the arrow pointing toward your screen 6
8. us rings is pointing toward your screen Adjustable extension 18 Align the safety knob on the mount assembly with the end of the arrow shaped slot on the mounting bracket B and screw it through the opening to prevent further rotation Hand tighten the securing knob 19 Hand tighten the remaining two tension knobs to secure the mounting bracket B to the mount assembly D CAUTION Check all of the hardware for proper tightness and security Do not over tighten the screws SEE FIGURE 4 WARNING When using the optional extension adapters and making a height adjustment while secured to the wall or ceiling do not remove the screws completely from the extension Failure to do so could result in injury and damage to the projector NOTE Use the Allen wrench key F for the following modification
Download Pdf Manuals
Related Search