InFocus INF5520 User's Manual
Contents
1. Battery Door 1 Insert a SD card not included into the camera s SD slot on the right hand side of the camera being careful to align the SD card appropriately 2 Attach the lens by aligning the dots and turning the lens clockwise until an audible click is heard 3 Set the Lens Focus Mode Switch located on the lens to AF 4 Using the Canon adapter kit plug the AC adapter into the DC coupler AC Power Cord AC Adapter E 0C Coupler 5 Open the battery door located on the bottom of the camera and insert the DC coupler into the battery slot 6 Close the battery door being careful to route the AC adapter cable through the slot in the door PhotoBooth Assembly Page 11 7 Attach the camera to the pivot arm securely 8 Carefully loosen the pivot arm adjustment knob to make final adjustments to the camera s position being very careful of the camera A WARNING Turning the adjustment knob will release the arm pivot points Damage to the camera could occur if the camera is allowed to fall 9 Connect the AC adapter to the AC power cord 10 Plug the other end of the AC power cord to a power strip or power outlet Page 12 PhotoBooth Assembly Preparing the Wireless Trigger 1 2 a Slide the battery door off Insert a 12V battery into the wireless receiver being careful of the battery orientation and slide the battery door back on D Slide the wireless receiver onto the bottom of2. the hot shoe Slide the hot shoe to the camera Note The receiver can also be attached using Velcro tape to the back of Mondopad Attach the sync cable from the sync socket on the back of the flash unit to the hot shoe Note Secure excess cable to avoid tripping hazard Attach the receiver cable to the Remote Control Terminal on the camera and attach the other end to the receiver Hot Shoe amp Receiver Sync Cable to Flash Unit Receiver Cable to Receiver PhotoBooth Assembly Page 13 Taking a PhotoBooth Photo Cell Button Power Switch 1 Turn Mondopad ON 2 Turn the camera s power switch to ON and the Mode Dial to M Manual 3 Turn the flash units power switch to the ON position 4 Verify that the Cell button LED is off If the Cell button LED is lit press the Cell button to turn it off 5 Press the receiver s power button and slide the slider from Hold to Ready 6 Slide the wireless transmitter button to Single Bulb 7 When ready click the transmitter button The image will be saved on the SD card and in the View amp Share gt PhotoBooth folder Page 14 PhotoBooth Assembly Framing Images 1 From the Mondopad home page navigate to View amp Share on Prorhas pada Enin ag Say hello to mI ppi ae lpr Womndecs 0 2 Open an image file Note Images created with PhotoBooth appear in the PhotoBooth folder 3 Tap Annotations Framing Images Page 15 7 Tap Fr
3. 8 8385 www infocus com support Page 22 Troubleshooting
4. NF5520 amp on do wnloads Page 8 PhotoBooth Assembly 3 Attach the flash unit to the half pole using the knurled clamp screw Tighten securely Knurled Clamp Screw Tilt Head 4 Slide the half pole onto the L bracket and adjust as needed 5 Adjust the half pole above the Mondopad panel allowing room for the camera 6 Adjust the angle of the flash unit and softbox to accommodate the camera and your situation using the flash unit tilt head 7 Plug the power cord into the flash unit and route through the mobile cart post 8 Plug the other end of the power cord into a power strip or power outlet PhotoBooth Assembly Page 9 Attaching the Pivot Arm A WARNING Do not attach the camera to the arm until it is fully positioned and locked into place 1 Insert the stud into the super clamp and attach the super clamp securely to the pivot arm 2 Position the super clamp along the top vertical bar of the Mondopad frame and tighten securely 3 Turn the large black adjustment knob on the pivot arm counterclockwise All pivot points will become loose 4 Position the arm similar to the image below and turn the adjustment knob clockwise to tighten Adjustment Knob Page 10 PhotoBooth Assembly Preparing the Camera Note For this section you will need the Canon AC adapter kit the Canon camera camera lens and an SD card required Mode Dial Power Switch Lens Focus Mode Switch SD Slot
5. ames from the menu ii i ee it Tow it fe fa 4 June ka 15 Las Pests Convention Center LE mO a Q e Created on the InFocus Mondopad at booth 5130 Page 16 Framing Images 9 To save the image tap Save JPG IN EM aed Ae June 9 15 Las Vegas Convention Center 11 Saved images can be viewed in the View and Share folder Framing Images Page 17 Note Saved images can also be found in the following folder Documents gt Mondopad Documents Adding New Frame Files to Mondopad 1 From within the Mondopad software navigate and login to Extras 2 Tap Minimize to go to the Windows Desktop 3 Navigate to the Zoos gt Files gt Frames folder 4 Copy and paste your PNG images from a thumb drive into this folder Page 18 Framing Images Note For best results PNG images should be the same resolution as the Mondopad 1920 x 1080 and have transparent centers Framing Images Page 19 Accessing additional documentation To complete the setup of this product and the Mondopad Collaboration software please download the Installers Guide located at www infocus com INF5520docs Page 20 Accessing additional documentation Troubleshooting The following table is meant to assist you with troubleshooting your PhotoBooth It is nota comprehensive list For the best troubleshooting advice we recommend reviewing the manufacturer s documentation associated with each part The flash unit is not turning on
6. e Verify that the modeling lamp mode is not set to OFF e Verify that the power switch on the back of the light is turned on e Verify that the power cord is properly connected e Unplug the light and check the main fuse standard type 5 x 20mm use only tempered fuse 8 AT p n 19022 on the back of the light located near the power cord If needed replace the fuse using the spare fuse in the handle See manufacturer s documentation for fuse replacement instructions e Unplug the light and check the modeling lamp fuse fast type 5x20mm 2 5AF p n 19035 See manufacturer s documentation for fuse replacement instructions e Check the flash tube e Check the modeling lamp Modeling lamp 110V 100W p n 23006 e Verify that the power outlet is good e Anerror code is displayed on the D Lite LCD screen Refer to the manufacturer s instructions The flash unit is at the wrong angle e Use the tilt head to adjust the angle of the Flash Unit The wireless transmitter is not triggering the flash e Verify that the transmitter is on the LED unit to flash will be on e Check to see if the receiver is connected properly to the camera e lf the transmitter or receivers Status LED is off or displaying a dim light replace the battery Follow manufacturer instructions e Verify that both the transmitter and receiver have good batteries which are properly installed and in the correct orientation e Decrease your distance between
7. ing the security allen wrench which was included with your Mondopad remove the two security screws on the top and bottom of the PC module 4 Using the PC handle carefully pull out the PC module Insert the new PC module and tighten the screws 6 Re attach the antennas on Preparing the Flash Unit 1 Disconnect the cap from the flash unit by sliding the blue lock slider button to the unlocked position and rotating the cap counterclockwise and lifting up PhotoBooth Assembly Page 5 2 Attach the speed ring to the flash unit by aligning the slots of the speed ring to the front of the flash unit and turning clockwise until it is fully attached Move the blue lock slider button to the locked position 3 Route the cables into each corner of the softbox Page 6 PhotoBooth Assembly 4 Insert the cable ends into the speed ring 5 Secure the Velcro at each corner of the softbox to complete its rectangle shape PhotoBooth Assembly Page 7 Attaching the Flash Unit 1 Attach the L bracket to the back of the Mondopad mobile cart NOTE If your mobile cart does not have holes drilled into it as per below please contact InFocus Support at www infocus com support 2 Attach the Mondopad panel to the mobile cart as per the manufacturer s instructions and the INF MOBCART addendum located on the InFocus Support site Direct link https portal infocus com support Product 20Pages downloads aspx mic I
8. m ndopad Reset Meet i OCs ua D T NS Getting Started View amp Share Browser Whiteboard Video Meeting Extras Schedule m InFocus ll Bright Ideas Made Brillian i Hi AN AA VAV DIRIA UTR IMPORTANT NOTES PhotoBooth is a combination of various manufacturer items such as the camera and light Please read all manufacturer documentation BEFORE following these instructions Pay particular attention to all safety and regulatory information contained therein InFocus is not liable for damage or injury caused by improperly using these items Trademark information Apple Mac and Facetime are trademarks or registered trademarks of Apple Inc Microsoft Windows PowerPoint Excel and Word are trademarks or registered trademarks of Microsoft Corporation The SDXC logo is a trademark of SD 3C LLC Canon and Rebel are trademarks or registered trademarks of Canon Inc D Lite It and Elinchrom are trademarks or registered trademarks of Elinchrom LTD Kaiser is a trademark or registered trademark of Kaiser Fototechnik GmbH amp Co KG Chimera is a trademark or registered trademark of Chimera Lighting Avenger and Manfrotto are trademarks or registered trademarks of Lino Manfrotto co Spa Lowel is a trademark or registered trademark of Lowel Light Manufacturing Vello Freewave and Impact are trademarks or registered trademarks of Gradus Group LLC InFocus In Focus INFOCUS stylized and Mondopad are either registered trademarks
9. or trademarks of InFocus Corporation in the United States and other countries All other trademarks are the property of their respective owners Any other trademarks service marks personal names or product names are assumed to be the property of their respective owners and are used only for reference There is no implied sponsorship affiliation certification approval or endorsement if we use one of these terms Contents IVIPOR TAIT NOTE Scree 1 Trademark ITON IAL ON arianen nren a e E 1 CONTENTS currsorirsi rues r inipon err rari IEN EE EI EEE EEA N E ATONE E OOOO O OEEO 2 Accessory IdeniNCa O asni EAEAN 3 PhotoBooth Assembly rions 5 PhotoBooth PC Module InstalatiOn ccccccseeecccsesecccceusecccueeescsusececsusessceueeesssusecsssuseceseusesssuecssssuesessseseseeeestsesecenas 5 Preparing ne Fash Uni cerris aan A E E EA EE E E OOO N N OO O E 5 Alaco tne FOSNU sree eas cca ane E EE ESAE ANAE ie add a nets cg stone ANE OO AEEA OOO E 8 Aa OTE TIO FIA aor EAA EA ENAA EEOAE NAE EAEAN AAE ONEA 10 Preparing the Cometa epiese nies RE E 11 Preparing the Wireless TriQG s ccccsssssccccsssesecessnseeseesenseeseecssaueseeessauneneeseesuuseeessaauseeeesaausaeessssaunseessauaneesessaaaeeseeeas 13 Taking a Phot Booth POLO teseosetescecece recesses ccotaceteseuswtendecsesteccesns ENIAN AE NO a Ea 14 Famine IMn S T T E 15 Adding New Frame Files to Mondopad s sessseseseseoscscscscscsosososososcsoscsososcscsoscsososososososososcsoeoscscecsoscs
10. sesseeessesesee 18 Accessing additional documentation sesesessosoeososcscecsososcscsoscscsoscsososososcscsoscsososososcsosososcscecsososcscscscssessesseeesee 20 TVOUDIGSWOO UNG esre 21 Accessory Identification Canon EOS Camera Flash Unit Kit Kit gt gt y Wireless Remote Sync Cord Hot Shoe Speed Ring Shutter Kit 0 lay a s7 b Canon AC Adapter Kit Super Clamp L Bracket Half Pole 18 30 46 74cm Pivot Arm with Camera Bracket Mondopad l Mobile Cart 2 Softbox Accessory Identification Page 3 The accessories which you receive depend upon the part number you ordered INF 5520 PB C INF PBKit NOMP cmeant E E Half Pole C E E gt x lt gt lt gt lt gt lt x lt gt x lt gt lt x lt MondopedMobleCort X Mondopad PC with X Photobooth Software installed Remote Shutter Kit a ee x lt gt lt gt lt Speed Ring Not shown on previous page gt lt gt lt x lt gt lt Page 4 Accessory Identification PhotoBooth Assembly PhotoBooth PC Module Installation If you ordered INF PBKit NOMP you will need to follow these instructions to replace your Mondopad PC Otherwise skip to the next section 1 Locate the Mondopad PC module on the back of the Mondopad panel 2 Rotate the two antenna connectors counter clockwise and disconnect them Set them aside in a safe place 3 Us
11. the transmitter and receiver e Extend the antenna on the transmitter The PhotoBooth images are not being saved in the e Verify that the camera s lens cap has been View amp Share gt PhotoBooth folder removed Troubleshooting Page 21 Verify that the camera power switch is turned on Turn the camera off and on again Verify that the camera s SD memory card is not full Verify that the camera s SD memory card is properly installed and that the card cover is closed Verify that the SD memory card write protect switch is set to the upward position to enable writing and erasing Verify the AC adapter is properly connected If using the camera s battery pack verify that the battery is fully charged and in the correct orientation Verify that the battery cover is closed Verify that the power outlet is good If the camera s LCD monitor displays an error refer to the camera manufacturer s reference guide The camera turned off Press the Disp Button on the camera Note The camera will turn off after 30 minutes of inactivity unless this feature is deactivated See the camera manufacturer s reference guide for more information The camera LCD monitor is displaying an error e Refer to the camera manufacturer s message reference guide For additional troubleshooting support please refer to the original manufacturer s documentation or contact InFocus Corporation Technical Support 6am 5pm PST 877 38
Download Pdf Manuals
Related Search